Page 1
FFLLYYW
WHHEEEELL EELLLLIIPPTTIICCAALL TTRRAAIINNEERR
SSFF--EE22331100
OOWWNNEERR’’SS MMAANNUUAALL
IMPORTANT!
PLEASE READ THIS MANUAL CAREFULLY BEFORE USING THE BIKE.
For Customer Service, please contact: support@sunnyhealthfitness.com
Page 2
1
Important Safety Information
We thank you for choosing our product. To ensure your safety and health,
please use this equipment correctly. Please read the information below carefully
before using this equipment.
1. It is important to read this entire manual before assembling and using the
equipment. Safe and effective use can only be achieved if the equipment is
assembled, maintained and used properly.
2. Before starting any exercise program you should consult your doctor to
determine if you have any medical or physical conditions that could put your
health and safety at risk, or prevent you from using the equipment properly.
Your doctor’s advice is essential if you are taking medication that affects
your heart rate, blood pressure or cholesterol level.
3. Be aware of your body’s signals. Incorrect or excessive exercise can
damage your health. Stop exercising if you experience any of the following
symptoms: pain, tightness in your chest, irregular heartbeat, extreme
shortness of breath, lightheadedness, dizziness or feelings of nausea. If you
do experience any of these conditions, you should consult your doctor
before continuing with your exercise program.
4. Keep children and pets away from the equipment. The equipment is
designed for adult use only.
5. Use the equipment on a solid, flat, level surface with a protective cover for
your floor or carpet. To ensure safety, the equipment should have at least
0.5 meters of free space all around it
6. Before using the equipment, please make sure all the nuts and bolts are
securely tightened. Always use the equipment as indicated. If you find any
defective components while assembling or checking the equipment, or if you
hear any unusual noises coming from the equipment during use, stop
immediately. Do not use the equipment until the problem has been rectified.
7. There are many functions of the computer, in which the value will show up
when using the equipment. Please note that the value of the heart pulse
displayed on the monitor is an estimate for reference.
8. Wear suitable clothing while using the equipment. Avoid wearing loose
clothing that may get caught in the equipment
9. The maximum weight of user is 300 LBS.
10. Care must be taken when lifting or moving the equipment so as not to injure
your back.
11. The equipment is not suitable for therapeutic use.
12. Please keep this manual and assembling tools for future reference.
13. This equipment is designed for indoor and home use only, not intended for
commercial use.
Page 3
55
1
3
2
5
4
7
8
9
10
9
10
10
9
9
11
11
12
12
13
13
14
14
15
15
16
16
17
17
17
17
17
17
18
18
19
19
20
20
21
21
22
22
22
22
22
22
23
23
24
24
25
25
26
20
28
26
20
28
29
29
29
29
30
30
31
31
32
32
33
33
34
34
35
35
36
36
37
38
39
39
39
39
32
33
32
33
32
33
32
33
40
40
41
41
42
42
42
42
43
44
45
46
47
48
49
5051521653
16
15
16
15
16
54
59
60
56
57
58
62
61
63
64
65
66
67
68
68
69
70
70
71
72
72
72
72
73
73
74
74
33
33
75
75
79
77
78
80
81
82
82
83
83
85
85
86
86
87
87
88
89
90
91
91
91
91
91
92
92
93
93
93
93
93
93
93
93
94
94
95
96
96
97
100
100
98
99
101
101
101
101
104
105
10
10
10
10
S6
S8
S8-14-22
106
107
108
109
76
76
76
76
27
102
78
84
35
35
103
103
110
110
6L
6R
2
EXPLODED VIEW
Page 4
NO
DESCRIPTION
QTY
NO
DESCRIPTION
QTY
1
Main frame
1 37
Left pedal 395*160*52
1 2 Front stabilizer
1 38
Right pedal 395*160*52
1 3 Rear stabilizer
1 39
Bolt M8*45*20*S14 grade A
4 4 Left handle bar
1 40
End cap J40*25*15
2 5 Right handle bar
1 41
End cap J60*30*15
2
6L/R
Left and Right Swing rod
2 42
Alloy wrap Φ28*4*φ24*12*Φ16.1
4 7 Left pedal post
1 43
Left nut 9/16*20*H8*S22 L
1 8 Right pedal post
1 44
Right nut 9/16*20*H8*S22 R
1 9 Screw M10*25*S6
4 45
Left pedal bolt Φ16*121.5*24*9/16*S8
1
10
Washer d10*Φ20*2
8 46
Right pedal bolt Φ16*121.5*24*9/16*S8
1
11
End cap J80*40*18
4 47
Knob M10*φ49*46
1
12
Transport wheel Φ71*Φ19*24
2 48
Brake rod Φ10*320*30*100
1
13
Screw φ7.8*30*M6*15
2 49
Spacer 20*20*120
1
14
Screw M6*12*S5
2 50
Spacer Φ11*Φ16.5*80 11g
1
15
Foot pad M10*30*Φ52*49
4 51
Spring Φ2.0*Φ15*54*N12
1
16
Nut M10*H7*S17
6 52
Square nut 16*16*25*M10
1
17
Alloy bush Φ38*5*Φ34*15*Φ25.4
6 53
Nut M6*H14*S10
1
18
Bolt M8*16*S14
2 54
Screw M6*10*Φ12
1
19
Washer d8*Φ32*2
2 55
Spring piece t2.0*15.8*153
1
20
Spring washer d8
4 56
Brake block 12*25*138
1
21
Wave washer d26*Φ34*0.3
2 57
EVA pad 10*22*95
1
22
End cap S13
6 58
Cow leather pad t5*25*138
1
23
Bolt M8*40*20*S14
2 59
Bolt M6*12*S10
2
24
End cap Φ28*32*Φ50
2 60
Washer d6*Φ12*1.2
2
25
Foam grip Φ26*3*600
2 61
Screw M5*18*Φ12
1
26
Arc washer d8*Φ20*2*R16
2 62
Nut M5*H4*S8
1
27
Swing rod axle
1 63
Screw M5*10*Φ10
1
28
Nut M8*H16*S13
2 64
Screw M5*20*Φ8.5
1
29
Plastic bush Φ32*3*Φ28*16*Φ14.3
4 65
Nut M5*H9*S8
1
30
Spacer Φ14*Φ8.3*48
2 66
Inertial wheel
20*Φ460*38*30*Φ40*4
1
31
Bolt M8*65*30*S14,grade 8.8
2 67
Inertial axle
Φ12*162*M12*1.0*30*50
1
32
Washer d8*Φ16*1.5
6 68
Bearing 6001-2RZ NBK
2
33
Nut M8*H7.5*S13
8 69
Small chain wheel two ways 16 teeth
1
34
Bolt M10*42*20*S17
2 70
Nut M35*1*Φ41*3
2
35
Washer d10*Φ25*2
4 71
Spacer Φ18*Φ12.1*8
1
36
Nut M10*H9.5*S17
2 72
Nut M12*1*H6*S19
4
3
PARTS LIST
Page 5
73
Nut M12*1*H19.5*S19
2 92
Screw M5*20*Φ8.5
2
74
Washer d12*φ24*2.0
2 93
Screw ST4.8*16*Φ10
8
75
Adjusting screw M8*83*Φ12*5
2 94
Screw M5*12*Φ8.5
2
76
Screw M10*16*S6
4 95
Washer d5*Φ10*1
2
77
Sensor stopper
1 96
Washer φ6.5*Φ25*6
2
78
Screw M5*10*Φ10
3 97
Computer
1
79
Big chain wheel
1 98
Trunk wire
1
80
Left crank
1 99
Sensor
1
81
Chain 1/2”*1/8”*106 KYC
1 100
Screw M6*12*Φ12
2
82
Crank cap Φ25*7
2 101
Sensor wire holder Φ12*11*Φ3
4
83
Bearing 6004-RZ NBK
2 102
Computer holder
1
84
Middle axle Φ20*146*37*74.5
1 103
D shape washer
2
85
Jump ring d20
2 104
Shipping front tube
1
86
Wave washer d20*Φ26*0.3
2 105
Shipping rear tube
1
87
Nut M10*1.25*H7.5*S14
2 106
Allen wrench S6
1
88
Inner chain cover
1 107
Allen wrench S8*33*80
1
89
Outer chain cover
1 108
Spanner S8 S14 S22
1
90
Front chain cover
1 109
Spanner S13-14-15
1
91
Fixing piece t0.8*11
5 110
Wave washer d17*Φ25*0.3
2
4
Page 6
5
HARDWARE PACKAGE
Page 7
1
76
10
76
10
105
104
6
STEP 1:
ASSEMBLY INSTRUCTIONS
A. Unscrew the screws (76) with wrench (S6), then remove and discard the
shipping rear tube (105) and the shipping front tube (104).
B. You can save these parts for future packaging and transportation of the bike if
desired. {screws (76), washers (10), shipping rear tube (105) and the shipping
front tube (104)}
Page 8
1
10
9
3
10
9
2
7
STEP 2:
A. Secure front stabilizer (2) and rear stabilizer (3) to main frame (1) with screws
(9) and washers (10).
Page 9
103
103
22
18
20
4
19
21
27
21
22182019
5
1
S13-14-15
S8-14-22
S14
8
STEP 3:
A. Attach swing rod axle (27) into main frame (1), insert wave washer (21) into the
swing rod axle (27) on both sides;
B. Secure left handle bar (4) and right handle bar (5) to swing rod axle (27) with
bolts (18), spring washers (20), washers (19) and D shape washers (103);
* NOTE: In order to tighten bolt #18 on both sides, use a spanner to hold on the
left side, and to tighten the right side. You are required to use both spanners.
C. Attach end cap (22) on bolt (18).
Page 10
S8
S8-14-22
S22
23
26
20
28
43
45
23
26
20
28
46
44
22
22
22
22
5
4
7
8
80
79
31
31
110
110
6L
6R
9
STEP 4:
A. Secure swing rod (6L) to left handle bar (4) and Swing rod (6R) to right handle
bar (5) with bolts (23), arc washers (26), spring washers (20) and nuts (28);
B. Secure right pedal post (8) to crank on the big chain wheel (79) with right pedal
bolt (46), wave washer (110) and right nut (44) by screwing clockwise;
C. Secure *left pedal post (7) to left crank (80) with left pedal bolt (45), wave
washer (110) and left nut (43) by screwing *counter-clockwise;
D. Attach end cap (22) on both sides of the bolt (31).
Page 11
33
32
38
39
33
32
7
8
37
39
10
STEP 5:
A. Secure left pedal (37) to left pedal post (7) with bolts (39), washers (32) and
nuts (33);
B. Secure right pedal (38) to right pedal post (8) with bolts (39), washers (32) and
nuts (33).
Page 12
97
100
100
98
102
78
1
11
STEP 6:
A. Secure computer holder (102) to main frame (1) with screws (100);
B. Secure computer (97) to computer holder (102) with screws (78), then connect
the wire of computer (97) with trunk wire (98).
Assembly is finished.
Page 13
22
31
22
33
30
II
I
After a period of time, the grease in the joint will become dry and it might
cause noise. Please follow instructions on how to lubricate the joint below:
Remove end caps (22), bolt (31) and nut (33) as diagram Ⅰ, then remove
spacer (30) as diagram Ⅱ, and add some grease on the surface and inside of
spacer (30) to decrease the rub, after finishing it, please assembly spacer
(30), bolt (31), nut (33) and end caps (22) back.
12
MAINTENANCE
Version: Mar 10, 2014
Loading...