Sunmi Technology W6900 User Manual

Open handle

NFC reader

Magnetic card reader

Power button

Short Press:

Wake up the screen, lock the screen.

Long Press:

Long press for 2-3 seconds in power oﬀ mode switches on the

device.

Long press for 2-3 seconds in normal operation mode selects power oﬀ or reboot.

Long press for 11 seconds when system is frozen automati cally reboots.

Volume buttons

Volume adjusts. These buttons can be set as quick scan button by

app setting.

Printer

For printing sales slips in power on mode.

Return button

Tap to return to the previous screen.

Home button

Tap to quickly go back home screen.

Menu button

Tap to quickly view the background apps. Select the app and slide laterally to close.

Magnetic card reader

Read the magnetic stripe information of bank cards.

IC card reader

Read the chip-based band cards.

NFC reader

Read the contactless card information.

Printer

USB interface

Indicator light

Power button

Volume buttons

IC card reader

Menu buttonHome buttonReturn button

Camera

Flash light

Extend pins

SAM card slot SIM card slot

SIM

Speaker

Battery

Strap ring

Indicator light

Remind the payment steps for band card.

USB interface

Use for charging or developer debugging.

Camera

5M Auto Focus, 1D&2D scanner.

Flash light

For lighting in camera mode.

SAM card slot

For inserting encrypted SAM cards.

SIM card slot

Note: To prevent system errors, please make sure the device is oﬀ when

you insert or remove the SIM card.

· Move the battery cover horizontally to open.

· Insert/remove SIM card in the direction as shown.

· Fasten the battery cover horizontally.

（Support GSM/CDMA/WCDMA/TDS CDMA/EVDO/LTE SIM card.）

Battery

Avoid contacting with water, metal material and other electrically equipment while in use.

Strap ring

For ﬁxing handheld strap to prevent slippage.

Extend pins

To connect to dock.(Need to buy dock separately)

Battery cover

①

Printing paper

③

②

Printing instructions

This device support 58mm thermal paper with the speciﬁcation of

57±0.5mm×Ø40mm

· Please open pater container with open handle, as shown in Fig.1. Please don’t open directly to damage print gear.

· Put the paper correctly into the pater container as shown and pull some paper outside the cutter, as shown in Fig.2.

· Close the cover of pater container to ﬁnish print paper feeding,

as shown in Fig.3.

Note: If the printed paper is blank, please check whether the paper roll has been installed wrong.

Ultra-simple setting

Only a few steps to start the smart business device

① 2G/3G/4G settings, in the power-oﬀ status, insert related 2G(GSM/CD-

MA)/3G(WCDMA/TDS CDMA/EVDO)/4G(LTE) SIM card and then power it on. (For card support details, please read the technical speciﬁcation table)

② Long-press the power button for 2 to 3 seconds, and then the screen is

lightened. Enter the ﬁrst power-on interface and just operate according to

instructions. The device provides two Internet accessing modes for selection.

③ WIFI setting

·Click the [setting] button, then enable WLAN, enter the WLAN search interface, and wait for its search for accessible WLAN hotspots and the

result;

·Click on the WLAN you want to connect to. If you select an encrypted

network, you need to enter the access code to connect.

How to download/un-install applications

In the networked mode, open the application market, browse and download applications to complete the installation of related applications.

Software uninstall method: select "Settings-> Applications-> Manage Applications-> Uninstall" to uninstall the application; or long press the

icon to drag it to the trash to uninstall.

USB interface

supply socket

Adapter

Instructions for charging and battery

This device supports charging by USB cable or dock.

· Connect the 5V adapter to the power supply socket.

· Connect the USB cable to USB interface of the device.

· The screen will display charging icon during charging.

· Please check the USB connect if there is no charging icon.

Instructions/Notes for battery

· This device adopts 3.6V/5200mAh Lithium battery, please don’t remove the battery.

· In order to protect the battery life, please charge your device whenever possible and don’t let battery to fully drain before charging.

Trouble shooting

Printer not working

· Make sure the cover of paper container is closed correctly.

· Make sure the right printing pater is used and fed.

· Check whether 58mm × 40mm thermal paper roll is fed into the paper container.

· If the printed paper is blank, please check whether the paper roll has been installed in the correct direction.

The device can’t be power on(eg, exhausted battery).

· Connect the device properly with a USB cable to charge for three minutes.

· Check whether the charging icon is displayed or not.

What we can do if the system freezes

Press the power button for 11 seconds to reboot.

Please read “Help App” in the device for more information on user’s guidance

Name and Content of Toxic or Harmful Substances in this Product

Toxic or Harmful

Substances

or Elements

Lead

（Pb）

Mercury

(Hg)

Cadmium

(Cd)

Hexavalent chromium

(Cr(VII)

Polybrominated

biphenyls

(PBB)

Polybrominated diphenyl ethers

(PBDE)

Means that the content of the toxic or harmful substance

in all homogeneous materials of this part is below the limit

stipulated in SJ/T11363-2006.

Means that the content of the toxic or harmful substance in

at least one of the homogeneous materials of this part is

beyond the limit stipulated in SJ/T11363-2006; but as for

the component marked with “×” on the table, the content is beyond the l imit since there is no alternative mature technology

in the industry yet.

The products reaching or exceeding the environmental service

life shall be recycled per “Regulations on the Control and

Management of Electronic Information Products” and shall not

be littered.

Part Name

Components of circuit board

Precautions

Safety Warning

· Insert the AC plug into the AC socket-outlet corresponding to the identiﬁcation input on the accessory power adapter;

· It must not be used where there is any potential explosive

gas;

· This is a Class A product. In a living environment, this prod uct may cause radio interference. In this case, the user may need to take practical measures against the interference.

· bout battery replacement:

① There is a risk of explosion if you replace the battery with

a wrong type!

② The replaced battery shall be handed over to repair per sonnel disposal. Do not throw it into the ﬁre!

Important Safety Instructions

· Try not to install or use the device during lightning, or else there would be lightning stroke danger;

· When you ﬁnd unusual smell, overheat or smoke, please cut oﬀ the power immediately;

· Be cautious of the sharp paper knife, and please do not

touch! ！

Suggestions

· Do not use it in extremely cold or hot conditions (e.g., near ﬁre or a lighted cigarette);

· Do not drop, throw or bend it;

· Try to use it in a clean and dustless environment and avoid tiny articles falling into the terminal;

· Do not use it near medical equipment without permission.

Declaration

The company shall not be responsible for the following actions

· Any damage caused by not using and maintaining it under the conditions described in the guide;

· Any damage or problem caused by optional parts or con sumptive materials (not the original products provided by the company or approved products), the company will assume no responsibility for this. It is not allowed to modify or change the product without the consent of the company.

· The operating system of this product supports oﬃcial system

update. If users install ROM system from the third party or

modify the system ﬁles by means of cracking, it may lead to

system instability, as well as security risk and security threat.

Disclaimer

Owing to the update of the product, some details of this document may not be in conformity with those of the product.

Please refer to the material object. The company reserves the

right to interpret this document. The company reserves the right to modify this instruction book without prior notice.

Product technical speciﬁcations

Item Technical Speciﬁcations

Operating system

CPU MTK 6737

CPU basic frequency

RAM 1GB LPDDR3

FLASH 8GB Nand Flash

Display

Touch screen Capacitive multi-touch screen, supportive of the glove mode

Camera 500W AF

Wireless data

Wi-Fi Build-in WIFI 802.11 a/b/g/n（2.4G/5G）

Bluetooth Support of bluetooth 3.0/4.0BLE and iBeacon

Keys Power key, volume key,

Interfaces USB Type C，SIM、PSAM、USB OTG

Printer type Thermal Printer

Printer paper spec

Magnetic card reader

IC card reader ISO7816\EMV2000\PBOC3.0

SAM Slot ISO7816

Contactless card reader

Battery 3.6V/5200mAh

Outline dimensions

Adapter

Android 6.0

Quad-core 1.3GHz

5.5 inch IPS, resolution 1280*720

2G：B2/B3/B5/B8 3G：wcdma(B1/B2/B4/B5);EVDO(BC0/BC1) 4G：B2/B4/B7/B17/B28

Width 58mm, maximum diameter 40mm

Track 1/2/3, Bi-directional, ISO7810/7811/7813

ISO 1443A/B

L211 mm × W83 mm × H54 mm

OUTPUT：DC5V/2A INPUT：AC100~240V/0.3A 50/60Hz

Package content

One host One user guide (including package content, product warranty

card and product qualiﬁcation certiﬁcate)

One power adapter One USB cable

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired operation.

FCC ID: 2AH25W6900

NOTE: Changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment oﬀ and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit diﬀerent from that

to which the receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help.

Body-worn Operation

This device was tested for typical body-worn operations. To comply With RF exposure requirements, a minimum separation distance of

1.0cm must be maintained between the user’s body and the handset, including the antenna.

Third-party belt-clips, holsters, and similar including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn

accessories that do not meet these requirements may not comply with

RF exposure requirements and should be

avoided.

Speciﬁc Absorption Rate (SAR) information:

This wireless phone meets the government's requirements for exposure

to radio waves. The guidelines are based on standards that were

developed by independent scientiﬁc organizations through periodic and thorough evaluation of scientiﬁc studies. The standards include a

substantial safety margin designed to assure the safety of all persons regardless of age or health.

FCC RF Exposure Information and Statement. The SAR limit of USA (FCC) is 1.6W/kg averaged over one gram of tissue.

Device types: W6900 has also been tested against this SAR limit. The highest SAR value reported under this standard during product certiﬁcation when properly worn on the body is 1.856W/kg（10gSAR， test distance：0mm，limit 4W/kg）and 1.477W/kg (1gSAR， test distance ：5mm，limit 1.6W/kg). This device was tested for body-worn

operations with the back of the handset kept 0mm and 5mm from the

body. To maintain compliance with FCC RF exposure requirements, use

accessories that maintain a 0mm and 5mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these

requirements may not comply with FCC RF exposure requirements, and

should be avoided.

Technical features and characteristic

the product includes the following features and characteristics：

Operation Frequency

GSM850

GSM1900

WCDMA bandII

WCDMA bandIV

WCDMA bandV

LTE Band 2

LTE Band 4

LTE Band 7

LTE Band 17

CDMA BC0

CDMA BC1

BLE

wiﬁ

Manufacture

Room 505 No.388 Song Hu Road Shanghai, China

824MHz-849MHz

1850MHz-1910MHz

1710MHz-1755MHz

824MHz-849MHz

1850MHz-1910MHz

1710MHz-1755MHz

2500MHz-2570MHz

704MHz-716MHz

824MHz-849MHz

1850MHz-1910MHz

2402MHz-2480MHz

2412MHz-2462MHz

5150MHz-5250MHz

5250MHz-5350MHz

5725MHz-5850MHz

Transmitted

33dBm

29dBm

21.5dBm

22.5dBm

23.5dBm

21.5dBm

23.5dBm

22dBm

21.5dBm

6dBm

-1dBm

18dBm

18.5dBm

Smart POS System

User’s Guide