Sunmi Technology NC010 User Manual

QUICK START GUIDE

Brief Introduction to Cash Drawer

Line Slot

Run the connecting wires on the box through signal wires in the slot orderly.

Signal Line

Get drive signal from receipt printer or POS machine to open the cash drawer.

Paper Money Clip

It is used to press down paper money to prevent it from warping.

Coin Slot Separation Sheet

A separation sheet used for separating coins, and upon being removed, two
slots will become a large slot for coins.

Paper Money Storage Slot

The place to store paper money.

Coin Storage Slot

The place to store coins. You can adjust the number of coin slots according
to your needs.

Three-Stage Lock Head

It supports manual opening, electric driving opening and locking functions.

Key

The cash drawer can only be opened with key with the same number as that
of the lock head.

Large Bill Storage Slot

The lower part of the coin storage slot is large bill storage slot. After taking
out the coin storage slot, you can see the large bill storage slot.

Instructions on Unlocking the Cash Drawer

Completely Locked

You can insert matching keys into keyhole and rotate to the completely l
ocked position, then the cash drawer will be locked and cannot be opened.

Electric Driving Opening

You can insert the matching key into keyhole and rotate to electric driving
opening position and then install the signal line by opening the back panel
baffle and plug the signal RJ12 connector into the driving device
(e.g. receipt printer and POS machine).

Opening with Key

You can insert the matching key into keyhole and rotate to manual opening
position to open the cash drawer.If you cannot rotate the key to the manual
opening position, please check whether the number on the key is the same
as that on the lock head.

Manufacturer: Shanghai Sunmi Technology Co., Ltd.
Address: Room 605, Building 7, Chuangzhi Tiandi, No. 388, Songhu Road,
Yangpu District, Shanghai

Table for Names and Content Identification of Toxic and Hazardous Substances
in this Product

Part Name

Circuit Board Component

Structural Component

Packaging Component

○：indicates that the content of the toxic and hazardous substance in all
homogeneous materials of the component is below the limit specified in
SJ/T 11363-2006.

X：indicates that the content of the toxic and hazardous substance in at least
one homogeneous material of the component exceeds the limit stipulated in
SJ/T 11363-2006. However, as for the reason, because there is no mature
and replaceable technology in the industry at present.

The products that have reached or exceeded environmental protection service
life should be recycled and reused according to the Regulations on Control and
Management of Electronic Information Products, and should not be discarded
randomly.

Basic Parameters

Nos. of Paper Money
Storage Slots

Nos. of Coin Storage
Slots

Service Life

Lock Head

Interface
Cash Drawer Size
Cash Drawer Weight
Driving Voltage
Working
Temperature/Humidity
Storage
Temperature/Humidity

Disclaimer

Due to product updating, some details of this document may not conform to the
product. Please refer to the real product. The right of interpretation of this
document belongs to our company. We reserve the right to amend this manual
without prior notice.

Toxic or Hazardous Substances and Elements

Pb Hg Cd

4 slots for paper money and 1 slot for large bill

Max 3 coin storage slots

≥ 1 million times
Equipped with number, three-stage switch

lock supports manual opening, electric driving
opening and locking. cash drawer can only be
opened with key by the same number.

RJ12
317mmx332mmx72mm
～2.8 Kg
DC 9V~24V

0℃～45℃ / 30%～85%

‐20℃～60℃ / 10%～90%

Cr(VII)

PBB PBDE

NC010

QUICK START GUIDE

NC010_CN_EN_V1.1

FCC Statement

Any Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.

Note: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment
and receiver.
—Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV
technician for help.