QLogic SANbox 5600/5602
Stackable FC Switch Hardware
Release Notes
For Installation in Sun™Storage Area Networks
Sun Microsystems, Inc.
www.sun.com
Part No. 819-6114-12
January 2008, Revision A
Submit comments about this document at: http://www.sun.com/hwdocs/feedback
Copyright 2008 Sun Microsystems, Inc., 4150 Network Circle,SantaClara,California95054,U.S.A.Allrightsreserved.
Sun Microsystems, Inc. has intellectual propertyrightsrelatingtotechnologythatisdescribedinthisdocument.Inparticular,andwithout
limitation, these intellectual property rights may include one or moreoftheU.S.patentslistedathttp://www.sun.com/patentsandoneor
more additional patents or pending patent applications in the U.S. and in other countries.
This document and the product to which it pertains aredistributedunderlicensesrestrictingtheiruse,copying,distribution,and
decompilation. No part of the product or of this document may be reproducedinanyformbyanymeanswithoutpriorwritten authorization of
Sun and its licensors, if any.
Third-party software, including font technology,is copyrighted and licensed from Sun suppliers.
Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark in
the U.S. and in other countries, exclusively licensed through X/Open Company,Ltd.
Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, Sun StorEdge, SunSolve, and Solaris are trademarks or registered
trademarks of Sun Microsystems, Inc. in the U.S. and in other countries.
All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International, Inc. in the U.S. and in other
countries. Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems, Inc.
The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sunacknowledges
the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry.Sun
holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s licensees who implement OPEN
LOOK GUIs and otherwise comply with Sun’s written license agreements.
U.S. Government Rights—Commercial use. Government users are subject to the Sun Microsystems, Inc. standard license agreement and
applicable provisions of the FAR and its supplements.
DOCUMENTATIONIS PROVIDED "AS IS" AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONSAND WARRANTIES,INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED,
EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.
Copyright 2008 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, Californie 95054, Etats-Unis. Tousdroits réservés.
Sun Microsystems, Inc. a les droits de propriété intellectuels relatants à la technologie qui est décrit dans ce document. En particulier, et sans la
limitation, ces droits de propriété intellectuels peuvent inclure un ou plus des brevets américains énumérés à http://www.sun.com/patents et
un ou les brevets plus supplémentaires ou les applications de brevet en attente dans les Etats-Unis et dans les autres pays.
Ce produit ou document est protégé par un copyright et distribué avec des licences qui en restreignent l’utilisation, la copie, la distribution, et la
décompilation. Aucune partie de ce produit ou document ne peut être reproduite sous aucune forme, par quelque moyen que ce soit, sans
l’autorisation préalable et écrite de Sun et de ses bailleurs de licence, s’il y en a.
Le logiciel détenu par des tiers, et qui comprend la technologie relative aux polices de caractères, est protégé par un copyright et licencié par des
fournisseurs de Sun.
Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de Californie. UNIX est une marque
déposée aux Etats-Unis et dans d’autres pays et licenciée exclusivement par X/Open Company,Ltd.
Sun, Sun Microsystems, le logo Sun, AnswerBook2, docs.sun.com, Sun StorEdge, SunSolve, et Solaris sont des marques de fabrique ou des
marques déposées de Sun Microsystems, Inc. aux Etats-Unis et dans d’autres pays.
Toutes les marques SPARC sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de SPARC International, Inc.
aux Etats-Unis et dans d’autres pays. Les produits portant les marques SPARC sont basés sur une architecture développée par Sun
Microsystems, Inc.
L’interfaced’utilisation graphique OPEN LOOK et Sun™ a été développée par Sun Microsystems, Inc. pour ses utilisateurs et licenciés. Sun
reconnaît les efforts de pionniers de Xerox pour la recherche et le développement du concept des interfaces d’utilisation visuelle ou graphique
pour l’industrie de l’informatique. Sun détient une license non exclusive de Xerox sur l’interface d’utilisation graphique Xerox, cette licence
couvrant également les licenciées de Sun qui mettent en place l’interface d ’utilisation graphique OPEN LOOK et qui en outre se conforment
aux licences écrites de Sun.
LA DOCUMENTATION EST FOURNIE "EN L’ÉTAT" ET TOUTES AUTRES CONDITIONS, DECLARATIONS ET GARANTIES EXPRESSES
OU TACITES SONT FORMELLEMENT EXCLUES, DANS LA MESURE AUTORISEE PARLA LOI APPLICABLE, Y COMPRIS NOTAMMENT
TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE, A L’APTITUDE A UNE UTILISATION PARTICULIERE OU A
L’ABSENCE DE CONTREFAÇON.
Please
Recycle
QLogic SANbox 5600/5602
Stackable FC Switch Hardware
Release Notes
This document contains important information about the QLogic SANbox 5600 and
SANbox 5602 Stackable Fibre Channel (FC) switch hardware installed in Sun
storage area networks (SANs).
Note – The only difference between the QLogic SANbox 5602 and 5600 switches is
that the 5602 has two hot-swappable power supplies, while the 5600 has one fixed
power supply.
Read this document so that you are aware of issues or requirements that can impact
the installation and operation of the QLogic SANbox 5600 and 5602 FC switch in a
Sun SAN.
Note – Sun is not responsible for the availability of third-party web sites mentioned
in this document. Sun does not endorse and is not responsible or liable for any
content, advertising, products, or other materials that are available on or through
such sites or resources. Sun will not be responsible or liable for any actual or alleged
damage or loss caused by or in connection with the use of or reliance on any such
content, goods, or services that are available on or through such sites or resources.
™
This document contains the following sections:
■ “Product Features” on page 2
■ “Switch Requirements” on page 2
■ “Downloading and Installing Patches” on page 5
■ “Related Documentation” on page 6
■ “Service Contact Information” on page 6
1
Product Features
The QLogic SANbox 5600 and 5602 FC switches are 4-Gbit Fibre Channel switches
that offer low price per port connectivity. The base QLogic SANbox 5600 and 5602
FC switch has the following ports:
■ Eight 4-Gbit ports enabled initially
■ Capability to add ports in 4-port increments up to a maximum of 20 ports
■ Four 10-Gbit ISL ports
■ Capability to move a currently licensed port to another port. This allows the
activation of up to all four 10-Gbit ISL ports with only an eight port license.
Note – The capability to move a licensed port to another port requires firmware
version 6.7.0.07 (minimum) and Enterprise Fabric Suite (EFS) version 6.07.05
(minimum).
Additional QLogic 560x FC switches can be stacked together by using the QLogic
SANbox 5600 and 5602 FC switch 10-Gbit ISL ports. QLogic 5200 FC switches can
also be included in the stack. Thus, a total of six QLogic 5200 and 560x FC switches
can be stacked together to create a maximum of 96 2-Gbit or 4-Gbit ports. (For
switch stacking details, refer to the QLogic documentation listed in “Related
Documentation” on page 6.)
Switch Requirements
This section describes some special requirements for the QLogic SANbox 5600 and
5602 FC switches. The following topics are discussed:
■ “Shipping or Moving a Rackmounted QLogic 5600 FC Switch” on page 3
■ “Shipping or Moving a Rackmounted QLogic 5602 FC Switch” on page 3
■ “Firmware Requirements” on page 3
■ “Installing the Switch Into an Existing Fabric” on page 4
■ “Management Software” on page 4
2 QLogic SANbox 5600/5602 Stackable FC Switch Hardware Release Notes • January 2008
Shipping or Moving a Rackmounted QLogic 5600
FC Switch
When mounting the QLogic SANbox 5600 FC switch in the equipment rack, you
must use the accessory mounting L-brackets supplied with the switch.
Caution – The supplied mounting L-brackets are not approved for moving or
shipping a QLogic SANbox 5600 FC switch installed in an equipment rack. The
brackets cannot sustain impacts and vibration associated with equipment relocation.
To move or ship a rack with a QLogic SANbox 5600 FC switch mounted in the rack
you must do one of the following:
■ Remove the switch from the rack
■ Use rack mounting kit SG-XSWQLG5200-RK-Z, which is designed for shipping
the rack with the switch installed.
Shipping or Moving a Rackmounted QLogic 5602
FC Switch
To move or ship a rack with a QLogic SANbox 5602 FC switch mounted in the rack,
you must do one of the following:
■ Remove the switch from the rack
■ Use rack mounting kit SG-XSWQLG5200-RK-Z, which is designed for shipping
the rack with the switch installed.
Firmware Requirements
For complete feature functionality, upgrade the SANbox 5600 or 5602 FC switch to
the minimum required firmware version 6.7.0.07. Features of this version include:
■ Support for EFS
■ Support for stacking of six switches
■ Ability to move port licenses
The latest firmware patch ID for this version is 128175-01. See the section
“Downloading and Installing Patches” on page 5 for further information regarding
the installation of this patch.
QLogic SANbox 5600/5602 Stackable FC Switch Hardware Release Notes 3
Installing the Switch Into an Existing Fabric
If you are installing a QLogic SANbox 5600 and 5602 FC switch into an existing
fabric that has a QLogic switch or a Sun StorEdge™ Network FC switch, you must
do the following:
1. Remove all 1-Gbit QLogic and Sun StorEdge Network 1-Gbit FC switches from
the fabric.
2. Upgrade any QLogic or Sun StorEdge Network 2-Gbit FC switches to the
minimum firmware version 5.0.1.10. The patch ID for this firmware is 119553. See
the section “Downloading and Installing Patches” on page 5 for further
information regarding the installation of patches.
Management Software
You can manage the QLogic SANbox 5600 and 5602 FC switches using Enterprise
Fabric Suite (EFS), QuickTools, or the CLI.
software and firmware version compatibility requirements for the SANbox 5600 and
5602 FC switches.
TABLE 1 summarizes the management
TABLE 1 Management Software and Firmware Version Compatibility
Firmware Version Firmware Patch ID Management Software Version
5.0.1.10 119553-03 SANSurfer Switch Manager 5.00.05
6.7.0.07 128175-01 EFS 6.07.05 (minimum)
EFS Requirements
If using EFS, firmware version 6.7.0.07 is required. For further SANbox 5600 and
5602 FC switch firmware information, see the section “Firmware Requirements” on
page 3. See the section “Downloading EFS” on page 4 for the EFS software
downloading procedure.
▼ Downloading EFS
1. Access the following QLogic web site:
http://lk.qlogic.com/productfeatureautomation/Home.aspx?id=
m13
2. Under the Download section, click Enterprise Fabric Suite 2007 - Download
Center.
4 QLogic SANbox 5600/5602 Stackable FC Switch Hardware Release Notes • January 2008
3. Type the CD serial number and click Continue.
4. Read and accept the license agreement.
5. Download the software.
Downloading and Installing Patches
The section that follows provides instructions for downloading and installing
patches for the QLogic SANbox 5600/5602, as well as any other QLogic or Sun
StorEdge Network 2-Gbit FC switches. See the sections “Firmware Requirements” on
page 3 and “Installing the Switch Into an Existing Fabric” on page 4 for the required
or recommended firmware versions and associated patch IDs.
▼ Downloading Patches
1. Access the SunSolveSMweb site at:
http://sunsolve.sun.com
2. Read and accept the terms and conditions of the License Agreement.
3. From the Support category, select Patches and Updates.
4. Under PatchFinder, type the patch ID and click Find Patch.
Do not type the -xx revision number. PatchFinder automatically finds the latest
patch.
5. Verify that you have retrieved the correct patch.
6. Print the page.
Printing this page also prints the patch README file, which contains the
installation instructions, special instructions, special guidelines, and notes.
7. Download the patch by clicking on either HTTP or FTP as shown in the
following line:
Download Patch (nn,nnn,nnn bytes) HTTP FTP.
8. Click PatchFinder and repeat the process from Step 4 for each patch.
QLogic SANbox 5600/5602 Stackable FC Switch Hardware Release Notes 5
Patch Installation
When you are finished downloading all the patches, install the patches by following
the instructions in each patch README file.
Related Documentation
For installation instructions, refer to the following QLogic documents:
■ SANbox 5000 Series Fibre Channel Switch Installation Guide (Firmware Version 6.7)
■ SANbox 5000 Series Quick Start Guide
For other important information regarding the QLogic SANbox 5600 and 5602 FC
switches and firmware, refer to the following files. These files are located on the
product CD that comes with the switch and the QLogic web site at
http://support.qlogic.com/support/sun_page.asp
■ FirmwareReadme_6.7.0.07.txt
■ FirmwareReleaseNotes_6.7.0.07.txt
Service Contact Information
If you need help installing or using this product in the United States, call
1-800-USA-4SUN, or go to:
http://www.sun.com/service/contacting/index.html
6 QLogic SANbox 5600/5602 Stackable FC Switch Hardware Release Notes • January 2008
Loading...