I. Features…………………………………………………….(P3)
II. Installation………………………………………………….(P3)
III. Set and Operation……………………………………..(P4-P9)
Main Parameters………………………………………………………(P4)
Diagram…………………………………………………………………(P4) Front Panel …………………………………………………………….(P5) Rear Panel……………………………………………………………..( P6) Panel Operation……………………………………………………….(P6-P9)
IV. Web Server………………………………………………. (P9-P17)
V. Notes……………………………………………………….(P18)
VI. Solution to ordinary problems……………………………(P18)
VII. Warranty Terms…………………………………..……...(P19)
(1) Single/dual input for choice, built in optical switch for dual input, the
switching power can be set by the button in the front panel or by web
snmp.
(2) Output adjustable by buttons in the front panel or web snmp, the range
is +0.5dBm~-4.0dBm
(3) Max multi 32 ports, with built in 1310/1490/1550WDM,max total output 37
dBm
(4) Standard RJ 45 port for remote control, we can provide output contract and
web manager for choice, and also plug-in snmp hardware can be reserved
for update.
(5) With laser key to turn on/off the laser.
(6) With RF test function.
(7) Adopts JDSU or Oclaro Pump laser
(8) Led displays the working condition of the machine
(9)Dual power hot plug power supply for choice, 90V~250V AC or -48V DC
II. Installation
Before installation
1. Please check if there is damage in outside of the machine
2. Please check the spare parts is complete or not, if not complete, please
contact the seller.
Installation
1. Please keep at least 1.75inches (4.5cm) space for cooling if the machine
installed with other machines.
2. Please check the power supply socket and the grounding of the power
supply, the grounding impedance should ≤4Ω, 220V power supply should
be with three cables and the grounding cable should be in the middle,
Unfitted grounding will damage the device or influence the signal quality.
3. Please make sure the power supply switch to off in the rear panel
4. Please confirm the fiber port is clean before connection the fiber.
1. The main component of the amplifier laser is sensitive to the static electricity,
so please keep the amplifier away from the static electricity. Furthermore,
please keep it away from caustic things. Please keep the amplifier in
temperature between -25℃and 65℃.
2. Please make sure the power is earthed.
3. Please don’t now attempt to look into the optical connectors when power
applied, eye damage may result.
4. Please don’t block up the heating dispersion hole and keep the machine
aired.
5. Please don’t unfold the machine or remove any parts of the machine.
6.Please don’t insert the patch cord when the power is on
7. Please don’t test the EDFA more than 5 times.
VI. Solution to some ordinary problem
1. Power supply light STATUS: green
LED light LASER: red
VFD display: NO LASER INPUT
Reason: No 1550nm optical input
Solution: Input 1550nm optical signal
2. In LED n it displays the right optical power, but not enough by test meter
Reason: 1. the optical meter is not very correct
2. the input optical power is out of the requested value( -3~10dB)
3. too big loss in the test pigtail
4. There is dust in the connectors
Solution:
Use absolute alcohol to wash the all the connects and the test point of
2. Don’t test EDFA with pigtail again and again, it will hurt the
fiber connector and make the factual power become smaller.
VII. Warranty Term
SUN-EYDFA Series optical amplifiers are covered by TWO YEAR LIMITED
WARRANTY, which starts from the initial date of your purchase. We provide its
customer whole-life technical supports. If warranty is expired, repair service
only charges parts (if required). In the event that a unit must be returned for
service, before returning the unit, please be advised that:
1. Warranty mark pasted on the housing of unit must be in good conditions.
2. A clear and readable material describes model number, serial number
and troubles should be offered.
3. Please pack the unit in its original container. If the original container is no
longer available, please pack the unit in at least 3 inches of shock
absorbing material.
NOTE: we donot assume responsibility for damage caused by improper
packing of returned unit(s).
The following situation is not covered by warranty:
1. The unit fails to perform because of operators’ faults.
2. Warranty mark is modified, damaged and/or removed.
3. Damage caused by Force Majeure.
4. The unit has been unauthorized alteration and/or repaired.
5. Other troubles caused by operators’ faults.
SHANGHAI SUN TELECOMMUNICATION CO., LTD.
Building No.145 Lane 666, Xianing Rd.
Jinshan Industrial Zone, Jinshan District
ShangHai, China 201506
Tel: +86 21 60138638
Fax: +86 21 60138635-401
E-mail: ics@suntelecom.cn
http://www.suntelecom.cn