SUNLOUNGER TIMER
ST100
The towel war is over
USER MANUAL / ENGLISH
Introduction
Dear Customer,
Thank you for using Sunlounger Timer.
This product complies with statutory European and American requirements.
To maintain this status and to ensure safe operation, you as the user must
observe these operating instructions!
These operating instructions are part of this product. They contain important
notes on commissioning and handling. Also consider this if you pass on the
product to any third party.
Therefore, retain these operating instructions for reference!
All company names and product names are trademarks of their respective
owners. All rights reserved.
Unit
Bolts
Mounting
plate
Rubber
seal
Sunlounger
Timer
Bolt
caps
Hex
key
Nuts Adapter
plate
Battery
cover & screw
Locking
screw
Getting Started
1. Take out the battery cover and place 2 x AA batteries.
2. The Sunlounger Timer is now operational.
3. Setup the current time, operation time and countdown time:
Setting mode
Display Countdown
/ Setting time
_
• Press and hold “M” to enter/exit settings
• Press “M” to switch between hours and minutes
• Press “+” or “-” to switch between setting modes
• Press “+” or “-” to setup the time data
Setting modes:
• Current time = real time at your location
• Countdown = countdown time when occupied
• Start time = when should the device be active
• End time = when should the device go on standby
+
M
Mounting
1. Depending on the type of chair and mattress, you might need to drill 4 holes
to mount the unit*.
2. Place the “adapter plate” on the front, “mounting plate” on the back and get
the “ bolts” through.
3. Cut the lenght of the bolts if needed. Cut only bolts where there is no thread!
4. Tight it all together by using the nuts and cover with bolt caps.
5. Add the “Rubber seal” on top of the “adapter plate”.
6 cutting areas on the bolt
Cut here
Cut here
Cut here
Cut here
Cut here
Cut here
*Warning: mounting the device as described is the responsibility of the user.
Sunlounger Timer is NOT responsible for the modications made on the chair/bed/mattress
Chair
Lock the device
1. Place the Sunlounger Timer on top of the “adapter plate”
and “rubber seal”.
2. And lock by tightening the “lock screw” with the “hex key”.
Using the Sunlounger Timer
1. LED light will ash blue when the device detect vibration.
2. LED light will ash red when its occupied.
3. The “Battery icon” will ash when the battery level is low.
4. The user can press “STOP” when done using the chair.
Battery
icon
STOP
button
LED
light
Current
time
Technical Specication
• Countdown display format: 24-Hour Time
• 6-digit display for time countdown
• Battery: 2 x AA batteries (not included)
• Battery life (standby): more than 2380 hours
• Battery life (vibration): more than 700 hours
• Battery life (avarage usage): more than 250 days
• Battery icon starts ashing when 30% is left
• Working temperature range: -30-70˚C / -22-158˚F
• Weather proof / water resistant
• Materials: Aluminum, rubber, stainless steel and electronics.
Intended use
The Sunlounger Timer is intended to only be used with the matching
application. Any other use than that described above can damage the product.
Additionally no part of this product must be modified or converted!
Read these operating instructions completely and attentively; they contain a
lot of important information on setup, function and operation. Always observe
the safety information!
Safety
The warranty/guarantee will expire if damage is incurred resulting from
non-compliance with these operating instructions. We do not assume any
liability for consequential damage! Nor do we assume any liability damage
to property or personal injury caused by improper use or failure to observe
the safety information. In such cases the guarantee/warranty will expire!
The following safety information is intended not only for the protection of
your health but also for the protection of the device. Please read the
following items carefully:
The authorized conversation and/or modification of the product is
inadmissible for safety and approval reasons (CE).
The product is for outdoor usage and is water resistant and NOT waterproof.
Do not place the device in liquids or place any objects on the device.
Be aware that the Sunlounger Timer surface can be hot and can cause
skin bruns in sunny days.
Do not place any open sources of re, such as burning candles on the device.
Handle the product with care. It can be damaged by inpact, blows or when
dropped even from a low height.
The product is not a toy and not suitable for children. Children cannot judge
the dangers involved when handling electrical devices.
Do not leave packing material unattended, it may become a dangerous toy
for children. Also observe the safety and operating instructions of the tooling
used to mount the product. Mounting the device as described is the
resposibility of the user. Sunlounger Timer is NOT responsible for any
modications made on any object.
Disposal
Product: Electronic devices are recyclable waste and must not be disposed of
in the household waste! At the end of its service life, dispose of the product
according to the relecant statutory regulations. Remove any inserted batteries/
rechargeable batteries and dispose of them separately from the product.
Batteries/rechargeable batteries: You as the end user are required by law
(Battery Ordinance) to return all used batteries/rechargeable batteries.
Disposing of them in household waste is prohibited! Batteries/rechargeable
batteries that contain any hazardous substances are labeled with the adjacent
icon to indicate that disposal in domestic waste is forbidden. The descriptions
for the respective heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead
(the names are indicated on the battery/rechargeable battery e.g. below the
rubbish bin symbol). You may return used batteries/rechargeable batteries free
of charge at the official collection points in your community, stores or wherever
batteries/rechargeable batteries are sold. You thus fulfill your statutory
obligations and contribute to the protection of the enviroment.
Maintenance and cleaning
Servicing or reair must only be carried out by a specialist workshop.
The product contains no parts that require servicing by you, except for the
batteries and mounting process as described. Therefore never open the
product (exept for the procedures described in these operating instructions
for insertion/replacing the batteries and mounting the device on objects).
A dry, soft and clean cloth is sufficient for cleaning the outside. Do not push
the display too strongly, as this will lead to scratches or demages.
Never use any aggressive cleaning agents, alcohol or other chemical solutions
that would damage the casing (discoloration).
Contact
RoHS
Reach
E-mail: info@sunloungertimer.com
Phone number: +45 6170 1198
www.sunloungertimer.com
Loading...