www.SunLED.com
PRELIMINARY SPEC
Features
●SINGLE COLOR.
●SUITABLE FOR ALL SMT ASSEMBLY AND
SOLDER PROCESS.
●AVAILABLE ON TAPE AND REEL.
●IDEAL FOR BACKLIGHTING.
●PACKAGE : 500PCS / REEL.
●MOISTURE SENSITIVITY LEVEL : LEVEL 4.
●RoHS COMPLIANT.
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Part Number: ZM2BB67S
4.0x4.0mm RIGHT ANGLE SURFACE MOUNT
LED LAMP
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ± 0.25(0.01") unless otherwise noted.
3.Specifications are subject to change without notice.
Absolute Maximum Ratings
A=25°C)
(T
Reverse Voltage V
Forward Current I
R 5 V
F 30 mA
M2BB
(InGaN)
Forward Current (peak)
1/10 Duty Cycle
i
FS 100 mA
0.1ms Pulse Width
Power Dissipation P
Operating Temperature T
T 111 mW
A -40 ~ +85
Storage Temperature Tstg -40 ~ +85
Electrostatic Discharge Threshold
(HBM)
Part
Number
Emitting
Color
1000 V
Emitting
Material
Unit
°C
Lens-color
Operating Characteristics
A=25°C)
(T
Forward Voltage (Typ.)
F=20mA)
(I
Forward Voltage (Max.)
F=20mA)
(I
Reverse Current (Max.)
(VR=5V)
Wavelength of Peak
Emission (Typ.)
F=20mA)
(I
Wavelength of Dominant
Emission (Typ.)
(I
F=20mA)
Spectral Line Full Width
At Half-Maximum (Typ.)
(I
F=20mA)
Capacitance (Typ.)
(V
F=0V, f=1MHz)
Luminous
Intensity
(IF=20mA)
mcd
M2BB
(InGaN)
F 3.2 V
V
F 3.7 V
V
R 10 uA
I
λ P
λ D
Δλ
458 nm
465 nm
22 nm
C 110 pF
Wavelength
nm
λ P
Viewing
Angle
2 θ 1/2
Unit
min. typ.
ZM2BB67S Blue InGaN Water Clear 110 278 458 120°
Published Date : FEB 27,2008 Drawing No :SDSA6298 V1 Checked : B.L.LIU P.1/5
Part Number: ZM2BB67S
www.SunLED.com
4.0x4.0mm RIGHT ANGLE SURFACE MOUNT
LED LAMP
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might leads to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
Published Date : FEB 27,2008 Drawing No :SDSA6298 V1 Checked : B.L.LIU P.2/5
www.SunLED.com
M2BB
Part Number: ZM2BB67S
4.0x4.0mm RIGHT ANGLE SURFACE MOUNT
LED LAMP
Published Date : FEB 27,2008 Drawing No :SDSA6298 V1 Checked : B.L.LIU P.3/5
Part Number: ZM2BB67S
www.SunLED.com
4.0x4.0mm RIGHT ANGLE SURFACE MOUNT
LED LAMP
Recommended Soldering Pattern
(Units : mm;Tolerance:
± 0.1)
Tape Specification (Units : mm)
The device has a single mounting surface. The device
must be mounted according to the specifications.
Remarks:
If special sorting is required (e.g. binning based on forward voltage, luminous intensity / luminous flux or wavelength),
the typical accuracy of the sorting process is as follows:
1. Wavelength: +/-1nm
2. Luminous Intensity / Luminous Flux: +/-15%
3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters.
Published Date : FEB 27,2008 Drawing No :SDSA6298 V1 Checked : B.L.LIU P.4/5
Part Number: ZM2BB67S
www.SunLED.com
4.0x4.0mm RIGHT ANGLE SURFACE MOUNT
LED LAMP
PACKING & LABEL SPECIFICATIONS ZM2BB67S
Published Date : FEB 27,2008 Drawing No :SDSA6298 V1 Checked : B.L.LIU P.5/5
Loading...