Electric Log Splitter
Electric Log Splitter
Model No. LJ601ERM
A Division of Snow Joe®, LLC
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may
result in serious bodily injury or death.
General Safety Warnings!
When using the log splitter, basic safety precautions should
always be followed to reduce the risk of re, electric shock,
and personal injury, including the following:
m WARNING! The use of any other accessory or
attachment might increase the risk of injury.
TRAINING
Before using the log splitter, take the time to familiarize
yourself with the controls, especially how to stop the log
splitter in an emergency. Only individuals who have read these
instructions and have a thorough understanding of these
instructions shall operate the log splitter. Never allow children,
under the age of 18, to operate the log splitter.
Retain this manual for future reference and reread it at the start
of each log splitting season.
1. Read, understand, and follow all instructions on the
log splitter and in the manual(s) before attempting to
assemble and operate. Save this manual for reference
and ordering replacement parts.
2. Never allow children under 18 years old to operate this
machine. Children 18 years old and over should be
trained and supervised by an adult who understands
the operation of the log splitter.
3. Never allow an untrained individual to operate the log
splitter.
4. Understand the function of all the controls and their
proper operation. Know how to stop the machine in
case of emergency.
PREPARATION
Work Area
1. Plan your log splitting pattern to avoid discharge of
material toward people, pets, and property. Thrown
objects can cause serious personal injury.
2. Always inspect the area where the log splitter is to
be used. Ensure the surface the machine is on is
60 – 75 cm (23.62" – 29.50") high, stable, level and free
from overhanging items such as limbs, wires etc.
Form No. SJ-LJ601ERM-880E
OPERATOR’S MANUAL
3. All visitors: children, adults, and pets, should be kept
at a distance from working area, at least 5 m (16.5 ft.)
from the log splitter while it is in operation. Stop the log
splitter if people or pets enter the discharge area.
4. Always observe the surface conditions to avoid
slipping, falling, and unexpected objects.
5. Avoid Dangerous Environments – Don’t use appliances
in damp or wet locations. Do not operate the log splitter
in the rain or wet conditions.
6. Operation of the log splitter where temperatures are
below 5ºC (41ºF) or above 40ºC (104ºF), at a high
altitude and/or high humidity may result in a malfunction
of the machine. Do not use the log splitter in poor
environmental conditions.
7. Ensure electrical conditions meet requirements (see
ElectricSafety).
8. Do not use the machine where gasoline, natural gas or
other ammable vapors are present. The electric motor
may spark and cause an explosion or re.
Protective Clothing
1. Thrown objects can cause serious injury to the eyes
and exposed body. Always wear safety glasses or
eye shields during operation and while performing an
adjustment or repair. Always use face or dust mask if
operation is dusty.
2. Use of rubber gloves and substantial footwear is
recommended when working outdoors. Wear protective
hair covering to contain long hair.
3. Always operate wearing adequate protective garments.
Dress Properly – Do not wear jewelry or other loose
clothing, which could become entangled in moving
parts. Wear footwear that provides protection for the
feet and ensures sure footing.
4. Always use ear protection if the noise level exceeds 85
dB. Observe any noise prevention regulations and laws.
5. Inspect the log splitter for worn, missing or damaged
parts and safety labels. See maintenance section for
detailed instructions.
6. Use the Right Appliance – Do not use this appliance for
any job except that for which it is intended.
Wood Condition
1. Do not split oversize logs (max. log diameter: 10", max
log length: 20"). Do not attempt to split “hard” wood
that requires more than 5 seconds to split.
2. Ensure the log is free from items that may be projected
or cause damage to the machine (ie.: nails, wire).
3. Ensure the end of the log is cut square and all branches
have been cut ush.
© 2013 Snow Joe, LLC
All rights reserved. Original instructions.
SAVE THESE INSTRUCTIONS
1
ELECTRICAL SAFETY
1. Always check that the power supply corresponds to the
voltage on the rating plate.
2. Do not operate in an area where there is a possibility
of body contact with grounded items (i.e.: pipes, metal
structures). Avoid contact with metal objects.
3. Do not pull/yank the power cord. Keep the power cord
away from hot surfaces and sharp objects.
4. Always use a grounded three-wire extension cord and
receptacle that are made of rubber and intended for
outdoor use. The machine is designed to operate on
120 Volt AC household current. The log splitter power
cord has a grounding prong. To avoid the possibility
of shock it must always be used with a properly
grounded three-prong receptacle protected with a 20A
fuse. Never remove the ground prong from the plug.
Grounding methods
Metal Screw
Cover of Grounded
Grounding
Pin
(C)
AA210
NOTE: If necessary, the machine can be switched to a
single-phase network (120V/60Hz). Connect the main
leads to a standard 120V/60Hz electrical supply which
has protection devices of under-voltage, over-voltage,
over-current as well as a residual current device (RCD)
with a maximum residual current rated at 30mA. Only a
qualied electrician should only do this.
5. Do not operate the machine where water is present (i.e.:
rain, sprinkler, puddles).
6. Do not touch electrical plugs with wet hands.
7. Keep the extension cord away from the moving parts
and hot motor housing.
8. Immediately replace and dispose of damaged wires
and plugs.
9. Do not open the switch box on the motor. If service is
necessary take the machine to a qualied electrician.
10. Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be
used for the gardening appliance. Receptacles are
Grounding
(A)
Adapter
Means
Outlet Box
(B)
Grounding
Pin
(D)
available having built-in GFCI protection and may be
used for this measure of safety.
11. Warning – To reduce the risk of electric shock, use
only with an extension cord intended for outdoor use,
such as an extension cord of cord type SW-A, SOW-A,
STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A, or
SJTOW-A.
EXCEPTION: Types SW, SOW, STW, STOW, SJW,
SJOW, SJTW, and SJTOW are alternative designations
to Types SW-A, SOW-A, STW-A, STOW-A, SJW-A,
SJOW-A, SJTW-A, and SJTOW-A, respectfully.
12. Extension Cord – Make sure your extension cord is
in good condition. When using an extension cord, be
sure to use one heavy enough to carry the current
your product will draw. An undersized extension cord
will cause a drop in line voltage resulting in loss of
power and overheating. Table 1 shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gage.
The smaller the gage number, the heavier the cord. To
reduce the risk of disconnection of appliance cord from
the extension cord during operating:
Minimum Gauge For Extension Cords
Volts
120V
Ampere Rating
More than
Not more than
0 – 6
6 – 10
10 – 12
12 – 16
NOTE – Only the applicable parts of the Table need to
be included. For instance, a 120-volt product need not
include the 240-volt heading.
i) Make a knot as shown in Figure 1 or
ii) Use one of the plug-receptacle retaining straps
Total length of cord in feet
25
18
18
16
16
50
16
16
14
12
AWG
Not Recommended
Not Recommended
Table 1
100
16
14
Method of securing extension cord
Cord set Appliance cord
(A) Tie cord as shown
Figure 1
(B) Connect plug and receptacle
150
14
12
2
or connectors described in this manual.
13. Avoid Unintentional Starting – Don’t carry plugged-in
appliance with nger on switch. Be sure switch is off
when plugging in.
14. Don’t Abuse Cord – Never carry appliance by cord or
yank it to disconnect from receptacle. Keep cord from
heat, oil, and sharp edges.
15. Don’t Force Appliance – It will do the job better and
with less likelihood of a risk of injury at the rate for
which it was designed.
16. Don’t Overreach – Keep proper footing and balance at
all times.
17. Stay Alert – Watch what you are doing. Use common
sense. Do not operate appliance when you are tired.
18. Disconnect Appliance – Disconnect the appliance from
the power supply when not in use, before servicing,
and when changing accessories.
19. Store Idle Appliances Indoors – When not in use,
appliances should be stored indoors in dry, and high or
locked-up place – out of reach of children.
20. Maintain Appliance With Care – Keep cutting edge
sharp and clean for best performance and to reduce
the risk of injury. Follow instructions for lubricating
and changing accessories. Inspect extension cords
periodically and replace if damaged, have it repaired by
an authorized service facility. Keep handles dry, clean,
and free from oil and grease.
21. Check Damaged Parts – Before further use of the
appliance, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other condition
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by
an authorized service center unless indicated elsewhere
in this manual.
OPERATION
Operator Requirements
1. Only one person shall operate the log splitter. All other
individuals and animals shall maintain a safe distance
during operation (see safety warning in Preparation).
2. Always operate the machine in a standing position and
in a location that is not in the path of projected debris.
The location of the machine should provide safe footing
and balance for the operator.
3. Do not operate the machine while under the inuence
of alcohol, drugs or physically, mentally fatigued.
Always be alert and watch what you are doing!
4. Contact with the moving parts can amputate body parts.
Do not put any part of your body near moving parts.
Workload Requirements
1. Never exceed the operating capacity of the log splitter.
2. Always split the log in the direction of the grain. Do not
place a log across the log splitter.
3. Never spilt more than one log at a time.
4. Do not load a log when the ram is moving.
Log Splitting
1. Remove any keys and adjusting wrenches before
turning the machine ON.
2. Do not use accessories or attachments that are not
recommended in this manual.
3. Place the log on the log retention brackets. Do not hold
or secure the log with your hands.
4. Do not split wood that takes more than 5 seconds to
split. Doing so will apply excessive pressure on the ram
cylinder and damage the machine.
5. Do not push/force the log onto blade. Always let the
blade initiate splitting the log.
6. If the log moves during operation, stop and reset.
7. If a log is jammed do not request assistance of
a second person. Ensure the machine power is
disconnected and built up pressure released before
attempting to release log.
8. Ensure the machine is turned OFF when not in use. If
the machine is left unattended then disconnect power
to the machine.
MAINTENANCE AND STORAGE
1. Maintain or replace safety and instruction labels. Ensure
safety guards are in place.
2. Disconnect the power and ensure built up pressure has
been released from the tool before cleaning, repairing,
or inspecting the log splitter.
3. For best operation keep the blade sharp, moving parts
lubricated and the machine cleaned.
4. Always check for damaged or worn parts, alignment of
moving parts, and tightness of bolts and screws before
each use.
5. Replace oil as specied in the Maintenance section.
Follow all local regulations and laws concerning
disposal of waste oil.
6. Qualied mechanics and electricians must carry out
repairs.
7. When not in use, always store the machine in a secure
location that children cannot access. Store the machine
in a dry environment. The machine can be transported
or stored in the ambient temperature between 25ºC –
55ºC (77ºF – 131ºF).
3
Safety Symbols
WARNING! Standard graphic symbols are used on all machines in order to ensure complete safety of all parts of the log splitter.
As these symbols are very important, read the information below attentively.
Symbols Descriptions
It is obligatory to read the machine’s use and maintenance manual in full
before using the machine.
It is obligatory at all times to wear gloves to protect the hands against chips
and splinters which may be produced during work.
It is obligatory to wear safety footwear at all times to provide protection
against the risk of logs accidentally falling on feet.
It is obligatory at all times to wear goggles or a visor to protect the eyes and
face against chips and splinters which may be produced during work.
It is forbidden to remove or tamper with the protection devices and safety
devices.
It is forbidden to stand in the range of action of the machine, apart from the
operator, no other person or animal may be present within a radius of 5 meter
(16.5 ft.) from the machine.
WARNING! Always be aware of the movement of the log pusher.
WARNING! Never remove a log trapped in the wedge with your hands.
WARNING! Disconnect plug before conducting maintenance.
WARNING! Voltage Hazard. Refer to rating plate for information.
To reduce risk of electric shock, do not expose unit to water or operated unit
on wet ground.
Always dispose of used oil according to the laws of the local where the
machine is operated in.
Danger of cutting or crushing of the hand: NEVER touch hazardous areas
while the wedge is moving.
4
Know Your Log Splitter
Figure 1
Part List Legends
1. Wedge
2. Oil Box
3. Carrying Handle
4. Motor w/push switch & circuit breaker
5. Rubber feet
6. Rolling wheel
7. ZHB hydraulic control lever
8. Safety guard for hydraulic control lever
9. Log pusher
10. Log retention brackets
is not damaged, all the parts are included and the log
splitter operates properly.
2. Bolt the Support Leg to the log splitter. Place the log
splitter on a level work surface that is at least 60 cm
(23.62") high.
3. Check that all the parts are included.
4. Before the initial operation the Bleed Screw should be
adjusted to allow air to go in and out of the oil tank.
(loosen three to four turns) Airow should be detectable
during operation. To avoid leaking oil close the Bleed
Screw when moving the machine.
Important! Failure to open the Bleed Screw during
operation will result in permanent damage to the log
splitter. Fig. 2 (13)
13
Figure 2
12
Technical Specications
• Model LJ601E
• Voltage 120V
• Frequency 60Hz
• Power 15A
• Max. splitting force 5 Tons
• Max. log diameter 10"
• Max. log length 20"
Assembly
m
WARNING! Do not connect the log splitter to a power
source until the machine is completely assembled. If any parts
are missing do not operate the machine until they
are replaced.
Follow these steps to assemble:
1. Remove log splitter from the carton. Keep the
packaging material until you are satised the log splitter
5. Dip stick Fig. 2 (12) Always check oil level before use.
m WARNING! Do not adjust the Max. Pressure Limiting
Screw. This was set at the factory so the log splitter works
under the maximum pressure limit of 5 tons. Tampering with the
screw will result in hydraulic pump failure. Only a professional
mechanic shall adjust the Max. Pressure Limiting Screw.
Fig. 3 (14)
Use your left
hand for the
Hydraulic
Control
Figure 3
14
5
How to Fill the Hydraulic Oil
m
WARNING! Frequently check the hydraulic oil. Fill
the hydraulic oil in the following manner. You must use the
appointed type specied hydraulic oil # HL-68 from Mobile,
Shell, or etc.
1. Put your machine on a vertical position. (Fig. 4)
2. Fit a cushion block (wood, brick, etc) which can
support the log splitter weight. The machine must be
perpendicular to the ground and stable.
Figure 4
5. Use a funnel to ll the hydraulic oil slowly as shown.
(Fig. 7) NOTE: Check the oil often by using a dipstick
level indicator to prevent oil from being overlled.
Figure 7
6. After lling, recheck that the oil level falls between the
two lines, then assemble the screw plug using the allen
wrench and tigten it. (Fig. 8)
Wood, brick,
or etc
3. Use an allen wrench to loose the screw plug on the
plate. (Fig. 5)
Figure 5
4. Check the oil level by the oil indicator on the screw oil
stick. Ensure the oil level falls between the two lines.
(Fig. 6)
Figure 8
7. Place the machine level and check to make sure there
are no leaks. (Fig. 9)
Figure 9
Figure 6
Oil level line
6
Operation
m
WARNING! Operators must read, understand, and
follow all instructions on the log splitter and in the manual(s)
before operating the machine. Never allow an untrained
individual to operate the log splitter. The operator must
understand the function of all the controls, their proper
operation and know how to stop the machine in case of
emergency. Never allow children under 18 years old to operate
this machine. Children 18 years old and over should be trained
and supervised by an adult who understands the operation of
the log splitter.
Follow these instructions to operate the log splitter:
1. Ensure all logs meet size requirements (max. log
diameter: 10", max log length: 20"). (Fig. 10)
2-10 inches
Figure 11
Use your
left hand for
the Hydraulic
Control
Use right hand for the
Push Button Switch
5. Split the log.
6. Release both your hands from the controls to return the
Log Pusher.
NOTE: The release of one hand from either control will
STOP the Log Pusher.
20 inches
Figure 10
IMPORTANT! Logs vary in hardness and structure.
Small logs with knots or harder wood may be more
difcult to split. Larger logs with less hardness may not
be difcult to split. Do not force the log splitter if the log
fails to split on the rst attempt.
2. Check that Bleed Screw is open.
3. Place a log in the Log Retention Brackets. Check to
make sure the log will not twist, rock, or slip during
splitting.
IMPORTANT! Follow all safety warnings (see Safety/
Operation: Workload Requirements, Log Splitting).
4. Engage the Log Pusher with the ZHB control system.
Use your left hand for the Hydraulic Control (Fig. 3)
and your right hand for the Push Button Switch
(Fig. 11). The system requires both controls be engaged
simultaneously.
IMPORTANT! Do not engage the Log Pusher for more
the 5 seconds.
Removing a Jammed Log
m
WARNING! Do not attempt to remove the jammed
log with your hands or knock it off. Doing so may cause
serious injury or damage to the machine.
1. Release both controls.
2. After the Log Pusher moved back and is completely
stopped, insert a wood wedge under the jammed log.
(Fig. 12)
Figure 12
7
3. Start the Log Pusher and push the wood wedge
completely under the jammed log.
4. Insert a second wood wedge under the log and repeat
step 3. (Fig. 13)
Figure 13
5. Repeat steps 3 and 4 until the jammed log releases
from the wedge. (Fig. 14)
log on the upper part. This will break the blade or damage
the machine. (Fig. 15)
Figure 15
Do not attempt to split 2 pieces of logs at simultaneously.
One of them may y up and cause injury. (Fig. 16)
Figure 16
Figure 14
Always set logs rmly on the log retaining plates and
worktable. Make sure logs will not twist, rock, or slip while
being split. Do not force the blade by splitting the
Do not try to knock the jammed log off. Doing so will
damage the machine or may launch the log and cause an
accident. (Fig. 17)
Figure 17
8
Troubleshooting
Problem
Motor won’t start
Fails to split logs
The log pusher moves jerkily,
making unfamiliar noise or
vibrating a lot
Oil leaks around cylinder ram
or from other points
Cause
Overload protection device
disengaged to protect the log
splitter from being damaged
Extension cord is too long,
causing the low voltage
Log is improperly positioned
The sizes or hardness of the
log exceeds the capacity of the
machine
Oil leaks
Unauthorized adjustment was
made on Max. Pressure
Limiting Screw. Lower max
pressure rating was set.
Lack of hydraulic oil and
excessive air in the hydraulic
system
Air sealed in hydraulic system
while operating
Suggested Remedy
Let motor cool down, and push
the button of the overload protection device to restart
the motor
Do not use extension cord
longer than 50 feet. Use the
extension cord as manual
recommended. (See pg. 2)
Refer to “Log splitter
operation” section for perfect
log loading
Reduce the log size before
splitting it on the log splitter
Locate leak(s) and contact the
dealer
Contact the dealer
Check oil level for possible oil
relling. Contact the dealer.
Loosen bleed screw by some
rotations before operating the
log splitter
Bleed screw is not tightened
before moving the log splitter
Oil drain bolt with dipstick is not
tight.
Hydraulic control valve
assembly and/or seal(s) worn.
9
Tight the bleed screw up
before moving the log splitter
Tighten the oil drain bolt with
dipstick
Contact the dealer
Maintenance
m
WARNING! Always disconnect the power and ensure
built up pressure has been released from the tool before
cleaning, repairing, or inspecting the log splitter.
Before every use:
• Clean the machine.
• Check safety labels and guards are in place.
• Check for damaged or worn parts, alignment of moving
parts, and tightness of bolts and screws.
Every 150 hours of use:
• Replace the hydraulic oil. Follow these steps:
a. Place container to capture drained oil on at, stable
surface. The container must hold a minimum of 3
liters (0.8 gallons).
b. Unscrew the oil drain bolt.
c. Turn the machine over on the motor side and drain
the oil.
d. Return the machine to the upright, operating
position.
e. Refresh the hydraulic oil. Recommended oils: Shell
Tellus T22, Aral Vitam GF22, SP Energol HCP22,
Mobile DTE 11 or equivalent. Do not use other
grade oils.
Periodically:
• Sharpen the wedge. Use a ne tooth le, take off burrs
and smooth rough sections of the cutting edge.
• Keep moving parts lubricated.
Service and Support
If your Sun Joe Electric Log Splitter requires service or
maintenance, please call 1-866-766-9563 for assistance.
Model and Serial Numbers
When contacting the company or reordering parts, you will
need to provide the model and serial numbers of the product,
which is found on the rear of your log splitter. Copy these
numbers into the space provided below.WARNING! Do not
tamper or remove any of the protection/safety devices.
Record the following numbers from the housing or handle of your
new product:
Model #:
L J 6 0 1 E R M
Serial #:
Storage
When not in use, always store the machine in a secure location
that children cannot access. Store the machine in a dry
environment. The machine can be transported or stored in the
ambient temperature between 25ºC – 55ºC (77ºF – 131ºF).
10
NOTES
11
A One-Year Full Warranty
for residential use
in the United States and Canada
General Conditions:
Snow Joe®, LLC warrants this product to the original purchaser for one year against defects in material or workmanship when used
for normal residential purposes. Snow Joe
part, subject to the conditions, limitations, and exclusions set forth herein. Such repair or parts replacement will be free from charge to
the original purchaser except noted below.
The duration of the warranty applies only if the product is put to personal use around the household or residence. If the product is put
to any business use, commercial or industrial, then the duration of this warranty is 90 days from the date of original purchase. If any
product is rented or leased, the duration of the warranty is 90 days from the date of original purchase.
It is the owner’s responsibility to perform correctly all maintenance, and minor adjustments explained in the owner’s manual.
Electric Products:
To obtain a replacement electric powered unit or repair the existing electric powered unit, you must return the complete unit and
postage prepaid to: Snow Joe Return Center, 86 Executive Avenue, Edison, NJ 08817.
Gasoline / Battery Products:
Limitations
• Batteries are warranted only for the period of 12 months after the date of purchase on a prorated basis. Rechargeable batteries
will be replaced free from charge during the rst 90 days. After the initial 90 days, batteries will be replaced at a prorated cost to
the customer.
• Idlers, cables, and electrical components are warranted to the original purchaser for use at household or residence for a period
of one year.
®
, LLC will repair any defect in material or workmanship, and repair or replace any defective
Exclusions
®
• Snow Joe
brand engines are covered under this warranty. All other engines and engine accessories are covered only by the
engine manufacturer’s warranty and are not covered by this warranty.
®
• Parts used that are not genuine Snow Joe
parts are not covered by this warranty.
• Damages resulting from misuse, alteration, improper assembly, improper adjustment, neglect, or accident which requires repair
is not covered under this warranty.
• Belts, augers, and tines are not covered under warranty – belts, augers, and tines wear out and can be purchased at
www.snowjoe.com or by calling 1-866-766-9563.
®
Snow Joe
obligating Snow Joe
, LLC may from time to time change the design of its products. Nothing contained in this warranty shall be construed as
®
, LLC to incorporate such design changes into previously manufactured products, nor shall such changes be
construed as an admission that previous designs were defective.
®
This warranty is intended to cover product defects only. Snow Joe
®
in connection with the use of the Snow Joe
Products covered by this warranty. This warranty does not cover any cost or expense
, LLC is not liable for indirect, incidental, or consequential damages
incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non-use of this
product, while waiting for completion of repairs under this warranty. Some states do not allow exclusions of incidental or consequential
damages, so the above exclusions may not apply in all states. This warranty may give you specic legal rights in your state.
®
If you wish to contact Snow Joe
, please direct inquiries to the:
Customer Service Department
Snow Joe Center
86 Executive Avenue
Edison, NJ 08817
®
Customers who have purchased Snow Joe
products exported from the United States and Canada should contact their Snow Joe®
Distributor (Dealer) to obtain information applicable for your country, province, or state. If for any reason, you are not satised with the
®
distributor’s service, or if you have difculty obtaining warranty information, contact your Snow Joe
®
are unsatisfactory, please write to the Snow Joe
Center at the above address.
seller. If in the event your efforts
If you have any questions about your product warranty, please call 1-866-SNOW-JOE or visit us online at www.snowjoe.com.
12
Loading...