Page 1
SUNIX Co., Ltd.
TEL : +886-2-8913-1987
Email : info@sunix.com.tw
USER’S MANUAL
Industrial Wireless Access Point
WAP-5XXX Series
Ver. 1.0, Dec. 2007
Page 2
1
Table of Content
TABLE OF CONTENT ............................................................................................................................................ 1
GETTING TO KNOW YOUR ACCESS POINT............................................................................................................ 3
1.1 About the Wireless Access Point .................................................................................................................. 3
1.2 Software Features......................................................................................................................................... 3
1.3 Hardware Features .......................................................................................................................................3
HARDWARE INSTALLATION.................................................................................................................................. 4
2.1 Installation WAP on DIN-Rail........................................................................................................................4
2.2 Wall Mounting Installation............................................................................................................................. 5
HARDWARE OVERVIEW....................................................................................................................................... 7
3.1 Front Panel ................................................................................................................................................... 7
3.2 Front Panel LEDs.......................................................................................................................................... 8
3.3 Bottom Panel ................................................................................................................................................ 9
3.4 Rear Panel....................................................................................................................................................9
CABLES AND ANTENNA..................................................................................................................................... 10
4.1 Ethernet Cables.......................................................................................................................................... 10
4.1.1 100BASE-TX/10BASE-T Pin Assignments............................................................................................................10
4.2 Wireless Antenna.........................................................................................................................................11
MANAGEMENT INTERFACE ................................................................................................................................12
5.1 Explore WAP-5002/WAP-5002P.................................................................................................................12
5.1.1 WAP-Tools software................................................................................................................................................12
5.1.2 UPnP Equipment......................................................................................................................................................13
5.2 Configuration by Web Browser ................................................................................................................... 14
5.2.1 About W eb-based Management...............................................................................................................................14
5.2.1.1 Main Interface...............................................................................................................................................15
5.2.2 Basic Setting............................................................................................................................................................16
5.2.2.1 Setting Operation Mode................................................................................................................................16
5.2.2.2 Setting WDS..................................................................................................................................................16
5.2.2.3 Setting W ireless.............................................................................................................................................20
5.2.2.4 LAN Setting..................................................................................................................................................23
5.2.2.5 Setting DHCP Server.....................................................................................................................................25
5.2.3 Advanced Setting.....................................................................................................................................................26
5.2.3.1 Wireless.........................................................................................................................................................26
5.2.3.2 MAC Filter....................................................................................................................................................27
5.2.3.3 System Event.................................................................................................................................................28
5.2.4 System T oo ls............................................................................................................................................................31
5.2.4.1 Administrator................................................................................................................................................31
Page 3
2
5.2.4.2 Date & Time..................................................................................................................................................32
5.2.4.3 Configuration................................................................................................................................................33
5.2.4.4 Firmware Upgrade........................................................................................................................................34
5.2.4.5 Miscellaneous................................................................................................................................................34
5.2.5 System Status...........................................................................................................................................................35
5.2.5.1 System Info...................................................................................................................................................35
5.2.5.2 System Log...................................................................................................................................................36
5.2.5.3 Traffic Statistics ............................................................................................................................................36
5.2.5.4 Wireless Clients.............................................................................................................................................36
5.2.6 Online Help..............................................................................................................................................................37
TECHNICAL SPECIFICATIONS............................................................................................................................. 38
Page 4
3
1
Getting to Know Your Access Point
1.1 About the Wireless Access Point
WAP-5002/WAP-5002P is a reliable IEEE802.11b/g WLAN with 2 ports LAN Access Point. It can be configured to
operate in AP/Bridge/Repeater mode. You can configure WAP-5002/WAP-5002P by Window Utility or WEB
interfaces via LAN port or WLAN interface. WAP-5002/WAP-5002P provides dual Ethernet ports in switch mode, so
you can use Daisy Chain to reduce the usage of Ethernet switch ports. WAP-5002P also provides PD feature on
ETH2 which is fully compliant with IEEE802.3af PoE specifications. Therefore, these wireless access points are best
communication solution for industrial grade wireless application.
1.2 Software Features
High Speed Air Connectivity: WLAN interface support up to 54Mbps link speed connection
Highly Secured Tranimission: WEP/WPA/WPA2/802.1X/Radius/TKIP supported
Support AP/Bridge/Repeater Mode
Switch Mode Supported: Daisy Chain support to reduce usage of switch ports
Secured Management by HTTPS and SSH
Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
1.3 Hardware Features
Fully Compliant with IEEE802.3af (Power Device at ETH2, WAP-5002P only)
Redundant Power Inputs: 12~48 VDC on terminal block
Operating Temperature: -10 to 55
o
C
Storage Temperature: -20 to 85
o
C
Operating Humidity: 5% to 95%, non-condensing
Casing: IP-30
10/100Base-T(X) Ethernet port
Dimensions(W x D x H) : 52 mm(W)x 106 mm( D )x 144 mm(H)
Page 5
4
2
Hardware Installation
2.1 Installation WAP on DIN-Rail
Each WAP has a Din-Rail kit on rea r pa nel. The Din-Rail kit helps WAP to fix on the Din-Rail. It is easy to install
the WAP on the Din-Rail:
Step 1: Slant the WAP and mount the metal spring to Din-Rail.
Metal Spring
Page 6
5
Step 2: Push the WAP toward the Din-Rail until you heard a “click” sound.
2.2 Wall Mounting Installation
Each WAP has another in stallation method to fix the switch. A wall mount panel can be found in the package.
The following steps show how to mount the WAP on the wall:
Step 1: Remove Din-Rail kit.
Page 7
6
Step 2: Use 6 screws that can be found in the p ackage to combine the wall moun t panel. Just like the picture shows
below:
The screws specification shows in the following two pictures. In order to prevent switches from any damage, the
screws should not larger than the size that used in WAP-5002/WAP-5002P.
Pozidrive
Step 3: Mount the combined WAP on the wall.
Page 8
7
3
Hardware Overview
3.1 Front Panel
The following table describes the labels that stick on the WAP-5002/WAP-5002P.
Port Description
10/100 RJ-45 fast
Ethernet ports
2 10/100Base-T(X) RJ-45 fast Ethernet ports support auto-negotiation.
Default Setting :
Speed: auto
Duplex: auto
Flow control : disable
P.O.E. PD Port
ETH2 of WAP-5002P com pliant with IEEE802.3af PoE. specifications
ANT.
Reversed SMA connecto r for external antenna.
WAP-5002P WAP-5002
Industrial Wir eles s A ccess Point
Industrial Wir eles s A ccess Point
WAP-5002WAP-5002P
PWR1
PWR2
Fault
ETH1
ETH2
10/100M
WLAN
ANT.
PWR1
PWR2
Fault
ETH1
ETH2
PoE
10/100M
WLAN
ANT.
PoE
Page 9
8
1. 2.4GHz antenna with typical 2.0dbi antenna.
2. LED for PoE power and system status. When the PoE power links, the green led will be light on.
3. LED for PWR1 and system status. When the PWR1 links, the green led will be light on.
4. LED for PWR2 and system status. When the PWR2 links, the green led will be light on.
5. LED for Fault Relay. When the fault occurs, the amber LED will be light on.
6. 10/100Base-T(X) Ethernet ports.
7. 10/100Base-T(X) Ethernet ports. (WAP-5002P contains PD function of PoE).
8. LED for WLAN link status.
9. LED for WLAN signal strength.
3.2 Front Panel LEDs
LED Color Status Description
Green On PoE power connected.
PoE
Green/Red
Red blinking
Indicates an IP conflict, or
DHCP or BOOTP server did
not respond properly
On DC power 1 activated.
PWR1
Green/Red
Red blinking
Indicates an IP conflict, or
DHCP or BOOTP server did
not respond properly
On DC power 2 activated.
PWR2
Green/Red
Red blinking
Indicates an IP conflict, or
DHCP or BOOTP server did
not respond properly
Fault
Amber On
Fault relay. Power failure or
Port down/fail.
On WLAN activated.
WLAN
Green
Blinking WLAN Data transmitted.
WLAN
Strength
Green On
WLAN signal strength.
1<25%, 2<50%, 3<75%,
4<100%
10/100Base-T(X) Fast Ethernet ports
On Port link up at 10Mbps.
10Mbps
LNK/ACT
Amber
Blinking Data transmitted.
100Mbps
Green On Port link up at 100Mbps.
Page 10
9
LNK/ACT
Blinking Data transmitted.
3.3 Bottom Panel
The bottom panel components of WAP-5002/WAP-5002P are showed as below:
1. Terminal block includes: PWR1, PWR2 (12 ~ 48V DC) and Relay output (1A@24VDC).
2. Reset bottom. Push the bottom 3 seconds for reset; 5 seconds for factory default.
PWR1, PWR2 (12-48V DC) and
Reset Button Relay output (1A@24VDC).
3.4 Rear Panel
The rear panel components of WAP-5002/WAP-5002P are showed as below:
1. Screw holes for wall mount kit.
2. Din-Rail kit
Page 11
10
4
Cables and Antenna
4.1 Ethernet Cables
The WAP-5002/W AP-5002P switches h ave standa rd Ethernet port s. According to the link type, the switch es use CAT
3, 4, 5,5e UTP cables to connect to any other network device (PCs, servers, switches, routers, or hubs). Please refer
to the following table for cable specifications.
Cable Types and Specifications
Cable Type Max. Length Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000BASE-TX
Cat. 5/Cat. 5e 100-ohm
UTP
UTP 100 m (328ft) RJ-45
4.1.1 100BASE-TX/10BASE-T Pin Assignments
With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 are used for
receiving data.
RJ-45 Pin Assignments
Pin Number Assignment
1 TD+
2 TD3 RD+
4 Not used
5 Not used
6 RD7 Not used
8 Not used
Page 12
11
The WAP-5002/W AP-5002P Ethernet ports support auto MDI/MDI-X operation. You can use a straight-through cable
to connect PC and switch. The following table below shows the 10BASE-T/ 100BASE-TX MDI and MDI-X port pin
outs.
MDI/MDI-X pins assignment
Pin Number MDI port MDI-X port
1 TD+(transmit) RD+(receive)
2 TD-(transmit) RD-(receive)
3 RD+(receive) TD+(transmit)
4 Not used Not used
5 Not used Not used
6 RD-(receive) TD-(transmit)
7 Not used Not used
8 Not used Not used
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.
4.2 Wireless Antenna
A 2.4GHz antenna i s used for WAP-5002/WAP-5002P and connected with a reversed SMA connecto r.
Page 13
12
5
Management Interface
5.1 Explore WAP-5002/WAP-5002P
5.1.1 WAP-Tools software
Each model contains friendly software, WAP-Tools, to explore WAP-5002/WAP-5002P on local area network.
Step 1: Open the WAP tool and click “Refresh list”, the WAP devices will show on the list.
Step 2: Choose your acce ss point, and it will show the WAP attribute. Simultaneity, you can manual set the WAP’s
IP address.
Step 3: Click “Access via web” button, it will go to web page.
Page 14
13
5.1.2 UPnP Equipment
Step 1: To check whether the UPnP UI of the computer is connected to the WAP-5002/WAP -5 002P, go to Control
Panel>Add or Remove Programs>Windows Components Wizard>Networking Servers>UPnP User
Interface and pitch on the UPnP User Interface.
Step 2: At the right-below corner of the computer, you will find a sign of the UPn P equipment.
Page 15
14
Step 3: Click the sign of the UPnP equipment, then you will find the UPnP equipment in the network neighborhood.
Step 4: Right click the UPnP equipment to choose “Properties”, it will show as the following pictures:
Step 5: Right click the UPnP equipment or double click the UPnP equipment to transfer; it will go to the web page.
5.2 Configuration by Web Browser
This section introduces the configuration by Web browser.
5.2.1 About Web-based Management
Inside the CPU board of the access point, it contains an embe dded HTM L web site residing in flash memory. With its
advanced management features, it allows you to manage the WAP from anywhere on the network through a
standard browser such as Microsoft Internet Explorer.
The Web-Based Management supports Internet Explorer 5.0. It is based on Java Applets with an aim to reduce
network bandwidth consumption, enhance access speed, and prese nt an easy viewing screen.
Note: By default, IE5.0 or later version does not allow Java Applet s to open socket s. You need to explicitly modify the
browser setting in order to enable Java Applets to use network ports.
Page 16
15
Enter the IP address of Wireless WAP (Default IP address is 192.168.1.1) in the Internet Explorer and press Enter,
you will see as follows, enter your user name (admin) and your password (admin), then click OK to continue.
Login screen
For security reasons, we strongly suggest you change the password. Click on System ToolsÆAdministrator and
modify the password.
5.2.1.1 Main Interface
The Home screen will appear . Please cl ick “Run Wi zard” to go to the HomeÆSetup Wizard p age to quick install the
WAP.
Main interface
Page 17
16
5.2.2 Basic Setting
5.2.2.1 Setting Operation Mode
Operation mode interface
The following table describes the labels in this screen.
Label Description
Bridge
This mode provides Static LAN-to-LAN Bridging functionality. The
static LAN-to-LAN bridging function is supported through Wireless
Distribution System (WDS).
AP
This mode provides Access Point services for other wireless clients.
In either mode, the WAP-5002/WAP-5002P forwards packet between its Ethern et interface and wi rele ss interface fo r
wired hosts on the Ethernet side, and wireless hosts on the wireless side.
5.2.2.2 Setting WDS
This type of wireless link is established between two IEEE 802.11 access points. Wireless packets transmitted along
the WDS link comply with the IEEE 802.11 WDS (Wireless Distribution System) format at the link layer.
Page 18
17
The following table describes the labels in this screen.
Label Description
WDS Mode
A Wireless Distribution System is a system that enables the wireless
interconnection of access points in an IEEE 802.11 network. It allows a
wireless network to be expanded using multiple access points without
the need for a wired backbone to link them, as is traditionally required.
The notable advantage of WDS over other solutions is that it preserves
the MAC addresses of client packets across links between access
points.
This provides different options (restricted mode, repeater mode, bridge
mode). Select the appropriate mode as per your application needs.
Encryption Type
Select the type of security for your wireless network
WDS Key
Fill in the encryption key when Encryption T y pe is TKIP or AES.
Peer MAC
Address
Set the MAC address(es) of other access point(s). Click on the box to
“Enable” it.
First of all, if WAPs link with WDS mode, it should obey the following rules:
1. LAN IP Address should set different IP in the same network.
Page 19
18
2. All WAP’s DHCP Server should disabled.
3. WDS should set Enable.
4. Each WAP should have the same setting except ‘Peer Mac Address’ set to the other’s Mac address
5. WEP Key and Channel should be the same, and each WAP’s SSID should be broadcast to see in the other’s
computer.
6. WAP’s distance should limit to a certain area.
WDS –Restricted Mode
The peer WDS WAPs are according to the MAC address listed in "Peer Mac Address" fields.
WDS –Bridge Mode
Same as Restrict mode in functionality and also one WDS link side can not set Peer Mac Address 1-4.
Page 20
19
The working principle of Bridge Mode as follows:
In the figure, the WAP behaves as a standard bridge that forwards traffic between WDS links (links that connect to
other WAP/wireless bridges) an d an Ethernet port. As a standard bridge, the WAP learn s MAC addresses of up to 64
wireless or 128 total wired and wireless network devices, which are connected to their respective Ethernet ports to
limit the amount of data to be forwarded. Only data destined for stations which are known to reside on the peer
Ethernet link, multicast data or data with unknown destinations need to be forwarded to the peer WAP via the WDS
link.
WDS –Repeater Mode
Same as Restrict mode in functionality and also one WDS link side can be set Peer Mac Address 1-4.
Page 21
20
The working principle of Repeater Mode as follows:
In the figure, Repeater is used to extend the range of the wireless infrastructure by forwarding traffic between
associated wireless stations and another repeater or WAP connected to the wired LAN.
5.2.2.3 Setting Wireless
The following table describes the labels in this screen.
Label Description
SSID
Service Set Identifier Default is the default setting. The SSID is a
unique name that identifies a network. All devices on the network must
share the same SSID name in order to communicate on the network. If
Page 22
21
you change the SSID from the default setting, input your new SSID
name in this field.
Channel
Channel 6 is the default channel, input a new number if you want to
change the default setting. All devices on the network must be set to
the same channel to communicate on the network.
Security options
Select the type of security for your wireless network at Security Type:
None: Select for no security.
WEP: Select for security.
WPA-PSK/WPA2-PSK: Select for WPA-PSK or WPA2-PSK without a
RADIUS server.
WPA/WPA2: Select for WPA (Wi-Fi Protected Access) authentication
in conjunction with a RADIUS server.
Security Type – None
If selected “None”, there will be no security protection on your wireless LAN access.
Security T ype – WEP
1. Security Type: Select WEP
2. WEP Encryption: Select 64 Bit or 128 Bit WEP encryption.
3. Key T ype: Select ASCII or Hex key type.
Page 23
22
4. Default Key Index: Select one of the keys to be the active key.
5. Key 1-4: Input up to four encryption keys.
ASCII (American Standard Code for Information Interchange) is a code for representing English letters as numbers
from 0-127. Hex digits consist of the numbers 0-9 and the letters A-F.
Security Type – WP A-PSK/WPA2-PSK
1. Security Type: Select WPA-PSK/WPA2-PSK.
2. Encryption Type: Select TKIP or AES encryption.
3. Share Key: Enter your password. The password can be between 8 and 64 characters.
Security Type – WPA /WPA2
1. Security Type: Select WPA/WPA2
2. Radius Server IP: Enter the IP address of the RADIUS Server.
3. Port: Enter the RADIUS port (1812 is default).
Page 24
23
4. Shared Secret: Enter the RADIUS password or key.
RADIUS (Remote Authentication Dial-in User Service) is the industrial standard agreement, and it is used to provide
an identify verification. The RADIUS customer (is usually a dial-in server, VPN server or wireless point) send your
proof and the conjunction parameter to the RADIUS server by RADIUS news. The RADIUS server validates the
request of the RADIUS customer, and return RADIUS news to back.
RADIUS server validates your proof, also carry on the authorization. So the RADIUS server received by ISA server
responded (point out the customer carries proof to be not granted) and it means that the RADIUS server did not
authorize you to carry. Even if the proof has already passed an identify verification, the ISA server may also refuse
you to carry a claim according to the authorization strategy of the RADIUS server.
The principle of the RADIUS server shows in the following pictures:
5.2.2.4 LAN Setting
The Basic SettingÆLAN Setting page is mainly set IP address for LAN interface. To access the WAP normally , a
valid IP address of your LAN should be specified to the LAN interface. The default IP setting is DHCP server (Obtain
an IP address automatically).
Page 25
24
The following table describes the labels in this screen.
Label Description
Obtain an IP
address
automatically
Select this option if you would like to have an IP address automatically
assigned to the WAP-5002/WAP-5002P by DHCP server in your
network
Use the following
IP address
Select this option if you are manually assigning an IP address.
IP Address: There is a default IP address (192.168.1.1) in the WAP,
and you can input a new IP address.
Subnet Mask: 255.255.255.0 is the default Subnet Mask. All devices
on the network must have the same subnet mask to communicate on
the network.
Default Gateway: Enter the IP address of the router in your network.
Obtain DNS
server address
automatically
This option is selected by DHCP server.
Use the following
DNS server
addresses
This option is selected by manually set
Preferred DNS: There is a default DNS server, and you can input
another new DNS server.
Alternate DNS: There is a default DNS server , and you can input
Page 26
25
another new DNS server.
5.2.2.5 Setting DHCP Server
The following table describes the labels in this screen.
Label Description
DHCP Server
Enable or Disable the DHCP Server function. Enable – the switch will
be the DHCP server on your local network
Start IP Address
The dynamic IP assign range. Low IP address is the beginning of the
dynamic IP assigns range. For example: dynamic IP assign range is
from 192.168.1.100 to 192.168.1.200. 192.168.1.100 will be the Start
IP address.
End IP Address
The dynamic IP assign range. High IP addre ss is the end of the
dynamic IP assigns range. For example: dynamic IP assign range is
from 192.168.1.100 to 192.168.1.200. 192.168.1.200 will be the End
IP address
Lease Time
(Hour)
It is the time period that system will reset the dynamic IP assignment to
ensure the dynamic IP will not been occupied for a long time or the
server doesn’t know that the dynamic IP is idle.
DHCP Clients List
List the devices on your network that are receiving dynamic IP
addresses from the WAP-5002/WAP-5002P.
Page 27
26
5.2.3 Advanced Setting
5.2.3.1 Wireless
The following table describes the labels in this screen.
Label Description
Beacon Interval
The default value is 100. The Beacon Interval value indicates the
frequency interval of the beacon. A beacon is a packet broadcast by
the WAP to synchronize the wireless network. 50 is recommended in
poor reception.
DTIM Interval
The default value is 1. This value, between 1 and 255 milliseconds,
indicates the interval of the Delivery Traffic Indication M essage (DTIM).
A DTIM field is a countdown field informing clients of the next window
for listening to broadcast and multicast messages. When the WAP has
buffered broadcast or multicast messages for associated clients, it
sends the next DTIM with a DTIM Interval value. Its clients hear the
beacons and awaken to receive the broadcast and multicast
messages.
Fragmentation
Threshold
This value should remain at its default setting of 2346. The range is
256-2346 bytes. It specifies the maximum size for a packet before data
is fragmented into multiple packets. If you experience a high packet
error rate, you may slightly increase the Fragmentation Threshold.
Setting the Fragmentation Threshold too low may result in poor
network performance. Only minor modifications of this value are
recommended.
RTS Threshold
This value should remain at its default setting of 2347. The range is
Page 28
27
0-2347 bytes. Should you encounter inconsistent data flow, only minor
modifications are recommended. If a network packet is smaller than
the preset RTS threshold size, the RTS/CTS mechani sm will not be
enabled. The WAP sends Request to Send (RTS) frames to a
particular receiving station and negotiates the sending of a data frame.
After receiving an RTS, the wireless station responds with a Clear to
Send (CTS) frame to acknowledge the right to begin transmission.
Xmit Power
This value ranges from 1 - 100 percent, default value is 100 percent. A
safe increase of up to 60 percent would be suitable for most users.
Higher power settings are not recommended for users due to excess
heat generated by the radio chipset, which can affect the life of the
WAP.
Wireless Network
Mode
If you have 802.1 1b & 802.11g devices in your network, then keep the
default setting, BG Mixed mode. If you have only Wireless-g devices,
select G Mode. If you would like to limit your network to only Wireless-b
devices, then select B Mode.
Transmission
Rate
The default setting is Auto. The range is from 1 to 54Mbps. The rate of
data transmission should be set depending on the speed of your
wireless network. You can select from a range of transmission speeds,
or keep the default setting, Auto, to have the WAP automatically use
the fastest possible data rate and enable the Auto-Fallback feature.
Auto-Fallback will negotiate the best possible connection speed
between the WAP and a wireless client.
Preamble
Values are Long and Short, default value is Long. If your wireless
device supports the short preamble and you are having trouble getting
it to communicate with other 802.11b devices, make sure that it is set
to use the long preamble
SSID Broadcast
When wireless clients survey the local area for wireless n etworks to
associate with, they will detect the SSID broadcast by the WAP. To
broadcast the WAP SSID, keep the default setting, Enable. If you do
not want to broadcast the WAP SSID, then select Disable.
5.2.3.2 MAC Filter
Use Advanced Setting Æ MAC Filters to allow or deny wireless clients, by their MAC addresses, from accessing
the WAP-5002/WAP-5002P. You can manually add a MAC address or select the MAC address from Connected
Clients that are currently connected to the W A P.
Page 29
28
The following table describes the labels in this screen.
Label Description
MAC Filter
Enable or disable the function of MAC filter. MAC address allowed or
denied option is selected by you.
MAC Filter List
This list will display the MAC addresses that are in the selected filter.
Connected
Clients
This list will display the wireless MAC addresses that linked with WAP.
MAC Address
MAC addresses need to be added to or clear from MAC filter list.
Apply
Click Apply to set the configurations.
5.2.3.3 System Event
When the event triggered at WAP, the notification procedure will be performed according to the type of the event.
Which notification would be performed depends on the selection of corresponding option in t he Adv anced Setting
Æ System Event page.
Page 30
29
System events record the activities of the WA P system. When the setting changes or action performs, the event will
be sent to administrator by email. A trap will also be sent to SNMP server. The Syslog will record the event locally
and may send the log remotely to a Syslog server . If serious event occurred, such as the power failure or link down,
the fault led will be switched on as warning.
Email Settings
The following table describes the labels in this screen.
Page 31
30
Label Description
SMTP Server
Simple Message Transfer Protocol, enter the backup host to use if
primary host is unavailable while sending mail by SMTP server.
Server Port
Specify the port where MTA can be contacted via SMTP serve r.
E-mail Address
1-4
Inputs specify the destination mail address.
SNMP Settings
The following table describes the labels in this screen.
Label Description
SNMP Agent
SNMP (Simple Network Management Protocol) Agent is a service
program that runs on the access point. The agent provides
management information to the NMS by keeping track of various
operational aspects of the WAP system. Turn on to open this service
and off to shutdown it.
SNMP Trap
Server 1-4
Specify the IP of trap server, which is the address to which it will send
traps WAP generates.
Community
Community is essentially password to establish trust between
managers and agents. Normally "public" is used for read-write
community.
SysLocation
Specify sysLocation string.
SysContact
Specify sysContact string.
Page 32
31
Syslog Server Settings
The following table describes the labels in this screen.
Label Description
Syslog Server IP
Not only the syslog keeps the logs locally, it can also log to remote
server. Specify the IP of remote server. Leave it blank to disable
logging remotely.
Syslog Server
Port
Specify the port of remote logging. Default port is 514.
5.2.4 System Tools
5.2.4.1 Administrator
In this page, you can change the username and password. The new password must be typed twice to confirm (the
default Name is “admin” and Password is “admin”).
The following table describes the labels in this screen.
Label Description
Old Name
This field displays the old login name. It's read only. The default value
of login name is "admin".
Old Password
Before making a new setting, you should provide the old password for
Page 33
32
a verify check. Acceptable inputs of this field contains '0-9', 'a-z', 'A-Z'
and must be between 0 to 15 characters in length. The factory default
value of login password is admin.
New Name
Enter a new login name. Acceptable inputs of this field contains '0-9',
'a-z', 'A-Z' and must be between 1 to 15 characters in length. This field
can not accept null input.
New Password
Enter a new login password. Acceptable inputs of this field contains
'0-9', 'a-z', 'A-Z' and must be between 0 to 15 characters in length.
Confirm New
Password
Retype the password to confirm it. It should be same as newly
selected.
Web Protocol
Choose on the protocol for web. The default value is HTTP, if you want
the web pages’ security is better, choose the HTTPS protocol.
Port
Corresponding to the Web protocol, there is a default port (HTTP: 80,
HTTPS: 443). And you can enter another number which should be in
range of 1-65535.
HTTPS (HTTP over SSL) is a Web protocol developed by Net sca pe and built into its browser that encrypts and
decrypts user page requests as well as the pages that are returned by the Web server.
5.2.4.2 Date & Time
In this page, set the date & time of the device. The correct date & time will be helpful for logging of system events. A
NTP (Network Time Protocol) client can be used to synchronize date & time with NTP server.
Page 34
33
The following table describes the labels in this screen.
Label Description
Local Date
Set local date manually.
Local Time
Set local time manually.
Time Zone
Select the time zone manually
Get Current Date
& Time from
Browser
Click this button; you can set the time from browser.
NTP
Enable or disable NTP function to get the time from the NTP server.
NTP Server 1
The initial choice about NTP Server.
NTP Server 2
The second choice about NTP Server.
Synchronize
Set the time, and the WAP’s time synchronize with the NTP Server at
the time
5.2.4.3 Configuration
The following table describes the labels in this screen.
Label Description
Download
configuration
The current system settings can be saved as a file onto the local hard
drive.
Upload
configuration
The saved file or any other saved setting file can be uploaded back on
the WAP. To reload a system settings file, click on Browse to browse
the local hard drive and locate the system file to be used. Click Upload
when you have selected the file to be loaded back onto the WAP.
Restore Default
Settings
You may also reset the WAP-5002/WAP-5002P back to factory
settings by clicking on Restore Default Settings. Make sure to save
Page 35
34
the unit’s settings before clicking on this button. You will lose your
current settings when you click this button.
5.2.4.4 Firmware Upgrade
New firmware may provide better performance, bug fixes or more functions. To upgrade, you need a firmware file
correspond to this WAP model. It will take several minutes to upload and upgrade the firmware. After the upgrade is
done successfully, the access point will reboot and get revalidated.
Important Notice: DO NOT POWER OFF THE WAP OR PRESS THE RESET BUTTON WHILE THE FIRMWARE
IS BEING UPGRADED.
5.2.4.5 Miscellaneous
If you want restart the access point through the Warm Reset, click Restart Now to restart the WAP.
Page 36
35
5.2.5 System Status
5.2.5.1 System Info
This page displays the current information for the WAP-5002/WAP-5002P. It will display model, as well as firmware
version, Ethernet, Wireless info and device time.
Page 37
36
5.2.5.2 System Log
The system log tracks the important events and setting changes of the WAP. If the WAP is rebooted, the logs are
automatically cleared.
Click the button 'Refresh' to refresh the page.
Click the button 'Clear' to clear the log entries.
5.2.5.3 Traffic Statistics
This page displays the network traffic statistics for both received and transmitted packets through the Ethernet port
and wireless connections associated with the WAP. Simultaneity, the traffic counter will reset by the device rebooting.
5.2.5.4 Wireless Clients
This page of the list displays the MAC Address of the wireless client s conn ected. Current TX Rate is corresponding
to the Transmission Rate in the Advanced Setting Æ Wireless pages.
Page 38
37
5.2.6 Online Help
Click on any item in the Online Help screen for more information.
Page 39
38
6
Technical Specifications
LAN Interface
RJ45 Ports 2 x 10/100Base-T(X), Auto MDI/MDI-X
Protection Built-in1.5KV magnetic isolation
Protocols ICMP, IP, TCP, UDP, DHCP, BOOTP , ARP/RARP, DNS,
SNMP MIB II, HTTPS, SSH, SNMPV1/V2, Trap, Private
MIB
P.O.E. PD Present at ETH2 of WAP-5002P
Power Device (IEEE802.3af):
IEEE 802.3af compliant input interface
Power consumption: 8Watts max.
Over load & short circuit protection
Isolation Voltage: 1000 VDC min.
Isolation Resistance: 10
8
ohms min
WLAN Interface
Operating Mode AP/Bridge/Repeater
Antenna Connector Reverse SMA
Radio Frequency Type DSSS
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g: OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band America/FCC: 2.412~2.462 GHz (11channel s)
Europe CE/ETSI: 2.412~2.472 GHz (13channels)
Transmission Rate IEEE802.11b: 1/2/5.5/11 Mbps
IEEE802.11g: 6/9/12/18/24/36/48/54 Mbps
Transmit Power IEEE802.11b/g: 18dBm
Receiver Sensitivity -81dBm@11Mbps, PER< 8%;
-64dBm@54Mbps, PER< 10%
Encryption Security WEP: (64-bit, 128-bit key supported)
WPA:
WPA2:802.11i (WEP and AES encryption)
Page 40
39
PSK (256-bit key pre-shared key supported)
802.1X and Radius supported
TKIP encryption
Wireless Security SSID broadcast disable
LED Indicators PWR 1(2) (PoE, WAP-5002P) / Ready:
1) Red On: Power is on and booting up.
Red Blinking: Indicates an IP conflict, or DHCP or
BOOTP server did not respond properly.
2) Green On: Power is on and functioning normally.
Green Blinking: Located by Administrator.
ETH1 (2) Link / ACT:
Orange ON/Blinking: 10 Mbps Ethernet
Green ON/Blinking: 100 Mbps Ethernet
WLAN Link/ACT: Green: Link, Orange: Poor signal
WLAN Strength:1<25%, 2<50%, 3<75%, 4<100%
Fault: WLAN link down (Red)
Power Requirements
Power Input Voltage PWR1/2: 12 ~ 48VDC in 6-pin Terminal Block
Reverse Polarity Protection Present
Power Consumption 6 Watts Max
Environmental
Operating Temperature -10 to 55oC
Storage Temperature -20 to 75oC
Operating Humidity 5% to 95%, non-condensing
Mechanical
Dimensions(W x D x H) 52 mm(W)x 106 mm( D )x 144 mm(H)
Casing IP-30 protection
Regulatory Approvals
Regulatory Approvals CE class A, RoHS
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4
(EFT), EN61000-4-5 (Surge), Level 3, EN61000-4-6 (CS),
Level 3
Shock IEC60068-2-27
Free Fall IEC 60068-2-32
Vibration IEC 60068-2-6
Page 41
40
Contact Information
Customer satisfaction is our number one concern, and to ensure that customers receive the full
benefit of our products, SUNIX services has been set up to provide technical support, firmware
updates, product information, and user’s manual updates.
Please feel free to contact us should you need any support or services.
E-mail for technical support
................................... info@sunix.com.tw
World Wide Web (WWW) Site for product information:
.................................... www.sunix.com.tw
Loading...