Page 1
771-FTLQIG000-NCI
Introduction
DIN-Rail InstallStep
Please check if the following items are present and in good condition upon opening
your package. Contact your vendor if any item is damaged or missing.
Industrial Ethernet Media Converter
Accessories
Din Rail Accessory Package 1
Wall Mountable Accessory Package 1
Fiber Lid 2
×
×
×
Features
Industrial grade design for stability and reliability
Extends 10/100/1000 LAN transmission distance up to 100KM with Single Mode
SC Fiber
Supports Link Fault Pass-through and far-end fault function
Supports 10/100/1000Base-T(X) auto negotiation and auto MDI/MDI-X
Built in a watchdog timer to monitor internal switching error
Relay output for power failure or port break alarm
Protect against electronic degradation and chemical corrosion
12V DC Jack & External power 12~48V DC terminal block with reverse polarity
protection
Detachable wall and DIN-rail mounting kit design
Plug-n-play & compact size designd
Extended operating temperature from -20~85 C
Version 1.0
The mediaconverters have incorporatedSUNIX advanced technologies
such asthe RS-422/485 autoidentify & switch,AHDC/CS (Auto Hardware
Direction Control/ Carrier Sense)technology, and auto baudrate detection
feature. SUNIXMedIO media converter, aspecialized equipment forindustrial
application whichcan effectively protectyour equipment fromlightning,
electrostatic discharges,high voltage, andground voltage damage,with
features likeSurge Protection, OpticalIsolation Protection, andReverse
Power Protection.Fiber Ethernet mediaconverters not onlyextends the
distances butalso provide featureslike Link FaultSignaling, which allows
application toreact to thesituation.
FTL-1218H-Gx
10/100/1000 Base-TXto 1000Base-FX MediaConverter
FTL-1218Hx
10/100 Base-TXto 100Base-FX MediaConverter
Model Specification
Converter
I
n
d
u
s
t
r
i
a
l
SUNIX CD
Quick Installation Guide (This Document )
User Manual ( In CD )
Industrial Ethernet Media Converters
Wall-Mounting Install Step
Package List
Step 1
Head for lower clip
Holes for Screws
Step 2
Step 3
Step 4
Step 5
Hook space to hold
pin/screw at wall
Holesfor Screw to fix wall
mount brackets
Power inputs& grounding
Note: This is option and if you tight this screw, DIN Rail mounting will be locked and
device can't be remove from DIN Rail without loosing this screw. You must tight this
screw after hanging the product at DIN Rail.
al
Quick Installation Guide
Page 2
FTL-1218H-Gx Series
Version 1.0
FTL-1218Hx Series
Alarm setON LED (Red)
(ON :Any DIPSwitch Set ON)
(OFF :All DIPSwitch Set OFF)
Fiber statusLED (Orange)
(ON :Fiber Link OK)
(Flash :ACT status)
10/100/1000Base-TX LANPort
Top V iew
TEL: +886-2-8913-1987
FAX: +886-2-8913-1986
Website: www.sunix-ncci.com.tw
E-mail: info@sunix-ncci.com.tw
Copyright© bySUNIX Co, LTD.
All rightsreserved.
Power-1 OnLED (Green)
By DC-Jackpower in)(
Power-2 OnLED (Green)
By MiniBlockpower in)(
Data TransmissionLED
(ON:LinkOK)
(Flash :Data Transmission)
Front Panel
Bottom View
Data TransmissionLED
(ON:LinkOK)
(Flash :Data Transmission)
4-Pin DIPSwitch :
No.1:power-1, enablealarm
No.2:power-2, enablealarm
No.3:RJ-45,enablealarm
No.4:Fiber, enablealarm
+V
-V G
P-1 P-2
POWER IN
Power V+Pin
TerminalBlock Power In
Power V-Pin
Relay -Pin
DC-Jack Powerin
RX
TX
10/100
ACT
/LINK
PWR-1
PWR-2
Alarm
Fiber
Industrial EthernetConverter FTL-1218H-G Series
Fiber TXPort
Fiber RXPort
1000Base-FX FiberPort
Converter
I
n
d
u
s
t
r
i
a
l
Industrial Ethernet Media Converters
321ON4
+ -
Ground Pin
Relay +Pin
Alarm setON LED (Red)
(ON :Any DIPSwitch Set ON)
(OFF :All DIPSwitch Set OFF)
Fiber statusLED (Orange)
(ON :Fiber Link OK)
(Flash :ACT status)
10/100Base-TX LANPort
Power-1 OnLED (Green)
By DC-Jackpower in)(
Power-2 OnLED (Green)
By MiniBlockpower in)(
Data TransmissionLED
(ON:LinkOK)
(Flash :Data Transmission)
FrontPanel
Bottom View
Data TransmissionLED
(ON:LinkOK)
(Flash :Data Transmission)
RX
TX
10/100
ACT
/LINK
PWR-1
PWR-2
Alarm
Fiber
Industrial EthernetConverter FTL-1218H Series
Fiber TXPort
Fiber RXPort
100Base-FX FiberPort
321ON4
Relay HardwareInstallation Guide
+V
-V G
P-1 P-2
POWER IN
+ -
DC24V
4-Pin DIPSwitch :
No.1:power-1, enablealarm
No.2:power-2, enablealarm
No.3:RJ-45,enablealarm
No.4:Fiber, enablealarm
ON : Alarm relay enable
OFF :Alarm relay disable
ON : Alarm relay enable
OFF :Alarm relay disable
Quick Installation Guide
Loading...