Sunitec Enterprise BS002 User Manual

BS300 User Manual

About BS300

The Bluetooth Stereo headset BS300 use the newest Bluetooth technology, It works with all Bluetooth enabled
compatible phone or music device, that supports Advanced Audio Distribution Profile (A2DP) and Audio Video Remote
Control Profile (AVRCP), And integrated FM transmitter, So you can change the Audio to the Car Radio to other FM
radio, This product is very fashionable for using on different occasions, it gives you the sound quality you've never
experienced.

About Bluetooth Technology

Bluetooth wireless technology is set to revolutionize the personal connectivity. By providing freedom from wired
connections-enabling links and connectivity between mobile computers, mobile phones, portable handheld devices and
other Bluetooth enables devices within 10 meters. Utilizing global sound & digital data 2.4G ISM transmission, it
makes global communication in the way you've never dreamed of!

Getting to Know Your BS300
Getting Started

To use your BS300, please follow these simple steps:
(a) Charge your headset.
(b) Place your phones to the headset no more than 10 meters.
(c) Pair your headset with Bluetooth-enabled mobile handsets.

Talk & Standby Time

The fully charged battery offers up to 9-10 hours talk time，this could be varied because of power consumption of
different phones, and up to 200 hrs Standby time. When no calls are in progress, the headset remains turned on and
under standby mode.

Charging Your Headset

The BS300 comes with a built-in rechargeable battery. Prior to using the headset, it is recommendable to charge the
battery fully for the first time. Normal fully charge time is 2 hrs approximately.

IMPORTANT:

(a) Charging indication will be delayed for a few minutes if the headset has not been used for a long time or the
battery is drained.
(b) When battery becomes low, LED will flash red and headset will emit a beep every 2 minutes. Please recharge the
battery as described above. To prolong durability of battery, it’s recommended to charge the headset whenever low
battery is encountered. Under low battery condition, if headset is continuously used, it’ll decrease durability of battery,
as well as standby time, and cause longer charge time than normal 2 hrs.

Turning On/Off the Headset

Turning On: Headset under off mode:

(a) Press and hold the MFB for 3 seconds until you hear a short beep. The LED will flash blue 3 times.
(b)Headset will be under standby mode. The LED will flash blue every 3 seconds.
Turning Off: Head set und er standby mode:
(a) Press and hold the MFB for 3 seconds until you hear a short beep. The LED will flash red 3 times.
(b) Headset will be off. The LED will flash stop.
IMPORTANT: Press the MFB again each time you turn on the Headset to reactive the paring so that the connection in
between the Headset and paired mobile handset is resumed. For pairing, please refer to procedures under “Pairing”.

Pairing

Page 1 of 6

Prior to using the BS300 for the first time, you must pair it wi th a Bluetooth-enabled mobile handset. The following
steps describe pairing instruction for a typical Bluetooth-enabled mobile handset.
(a) Place the BS300 and mobile handset no more than 1 meter apart.
(b) Ensure the Headset is OFF.
(c) Press and hold the MFB for 6 seconds unt il the Headset LED alternately flash red and blue. It’s no w ready for

pairing.

(d) Activate your mobile handset’s Bluetooth function by referring to your mobile handset user guide for d etails. Mean

while, the handset will search for accessible Bluetooth devices.

(e) Select “BS300” from the list.
(f) Enter the pre-programmed passkey “0000” and press “OK” to pair the headset and the handset. When pairing is

completed, the headset LED will flash blue every 3 seconds and under standby mode.

(g) Press “Return” to go back to your handset’s main menu. For certain mobile handset models, a headset icon will be

shown on the screen. You should now be able to make and receive calls using your headset.

IMPORTANT: If the pairing cannot be completed within 2 minutes while the pairing mode is activated, the headset
LED flashes blue every 3 seconds and is under standby mode. Please repeat step (b) to (g) to pair the headset and
mobile handset again.

Connection/Link between Headset and mobile Handset :

After pairing is completed, headset is always under standby mode. Before you place or answer a call, if the headset
ICON is not shown on phone screen, please follo w the simple steps to activate the Bluetooth connection/link through
your handset or headset until the headset ICON is on the screen.

(1) On Handset: Select “BS300” from the paired list on your handset screen.
(2) On Headset: Short press MFB and select “Accept” on handset screen to accept connection.
(3) On Headset: Short press Vol+ or Vol- for Connecting AV profile

IMPORTANT: Whenever Bluetooth connection/link is removed, for example: power off on headset/phones or out of
10 meter sensing distance, please activate connection/link as suggested. If not connected within 10minutes,the headset
will be power off automatically.

Disconnect io n between Headset and mobile Handset:

You may con nect your h ead set with an other Blu etooth e nab led ha ndset. Please follow the simple steps to disconnect the
headset with the pre-paired handset.
(a) Power off the headset
(b) Select “disconnecting” to remove connection from your handset list.

Using the Headset

Once pairing is completed, you may access the following functions. Some of the below-mentioned function is only
accessible for handsets supported with Hands-Free Profile.
1 Answering a Call:

To answer a call, wait for the headset to ring, then short press the MFB for approx. 1 second, to accept the call or
answer the call via your mobile handset in the normal way.

2 Ending a Call:

Short press the MFB for approx. 1 second, to end your call or end the call via your mobile handset in the normal
way.

3 Reject an Incoming Call:

When you hear the ringing tone, press and hold MFB for 3 seconds until the headset emits a short beep.

4 Voice Dialing:

If your mobile handset is voice dialing enabled, under standby mode, press Vol+ or Vol- for 3secs and when you hear
a beep, say the voice tag.

Page 2 of 6