Sunitec Enterprise BH003 User Manual

CRC#: 5278691

Multipoint Bluetooth

Mono Headset

Instruction Manual

Before using this product, read this manual carefully and retain it for future reference.

4. Charging Your Bluetooth Headset

The Bluetooth Headset c Prior to using the headset, it is recommended to charge the battery fully for the ﬁrst time. Normal full charge time is 2 hrs. (approx.)

IMPORTANT:

(1) Charging indication will be delayed for a few minutes if the headset has

not been used for a long period time or the battery is drained.

(2) To prolong durability of battery, it is recommended to charge the

headset whenever a low battery signal is encountered.

When battery becomes low, the LED will ﬂash red every 3 seconds.

Under a low battery condition, if headset is continuously used, it will decrease the durability of battery as well as the standby time.

This causes a longer charge time than the normal 2 hours and the

headset will power oﬀ.

(3) The red LED will ﬂash on while charging, and will turn oﬀ when

charging is completed.

omes with a built-in rechargeable battery.

5. Turning ON/OFF the Headset

POW ER ON:

When the headset is under oﬀ mode, press and hold the “MFB” for 3 seconds until you hear a short beep. The red LED will ﬂash 3 times, and then the headset will automatically connect the last connected mobile phone.

POW ER OFF:

When headset is in standby mode, press and hold the “MFB” button for 3 seconds until you hear a short beep. The red LED will ﬂash 3 times before power oﬀ.

6. Pairing

Prior to using the headset for the ﬁrst time, you must pair it with a Bluetoothenabled mobile phone. The steps below describe pairing instructions for a typical Bluetooth-enabled mobile phone.

(1) Place the headset and mobile phone no more than 1 meter apart. (2) Ensure the headset is in OFF mode. (3) Press and hold the “MFB” button for 6 seconds until the red LED ﬂashes

on. I t is now ready for pairing. (4) Activate the Bluetooth function on your mobile phone. (Refer to your mobile phone owner’s manual). (5) Select : ”BT Headset” from the list. (6) Enter the pre-programmed code “0000” and press “OK” to pair the

headset and the phone. When pairing is completed, the headset is now

in standby mode with the red LED ﬂashing every 3 seconds.

-02-

(5) LAS T NUMBER RE- DIALING In standby mode, press the “MFB” button twice for last number redial. (6) ADJ USTING THE VOLUME During a call, press the “V+” or “V-” buttons repeatedly until you reach

the desired volume level.

(7) MUTE & UN-M UTE

a. Mute: During a call, press and hold the “V-” button for 3 seconds

to mute the headset. The red LED will ﬂash on during mute mode. Un-Mute: press and hold the “V-” button 3 seconds to un-mute

the headset.

(8) TRAN SFERRING C ALLS

a. Headset to Mobile Phone: During a call, press and hold the “V+”

button for 3 seconds. The call is routed to your mobile phone. b. Mobile Phone to Headset: Press and hold the “V+” button for 3 seconds to route the call to the headset.

(9) HOLD THE CALL During a call, press the “MFB” button twice to hold the phone call. Press “MFB” button twice again to resume conversation. (10) Answer the Second Call

a. When receiving a second call, press “MFB” button twice to hold

the ﬁrst call on line and answer the second call.

b. When receiving a second call, press “MFB” button once to end the

ﬁrst call and answ (11) Reject the Second Call When receiving a second call, press and hold the “MFB” button for 2 seconds to reject the second call. (12) Switch Between 2 Phone Calls

a. When having 2 calls on the line, press “MFB” button twice to

switch between these 2 phone calls.

b. When having 2 calls on the line, press “MFB” button once to end

the ﬁrst call and stay with the second call.

er the second call.

10. MultiPoint Feature

(1) Activate Multipoint Connection

The default setting of headset’s multipoint function is on. Please activate the multipoint function for connecting with 2 mobile phones in the same time.

a. MULTIPOINT ON : In standby mode, press and hold “V+” button

for 6 seconds until you hear a beep. After turning on the

multipoint function, the headset will automatically connect to

the last 2 mobile phones that have been paired before.

-04-

11. Low Voltage Protection of Battery

When the voltage of the battery is decreased to 3.3 V, the red LED will ﬂash every

3 seconds, and the headset will be powered oﬀ automatically when the

voltage is less than 3.0 V.

12. Restore to Default Setting

Follow the steps below to reset the headset to its original setting and remove all previous pairings and connections.

(1). Ensure the headset is under standby mode. (2). Press and hold both of “V+” and “V-” buttons for 10 seconds until

the red LED ﬂashes 5 times, then the headset will resume in standby mode. The headset is now back to its original setting. After powering on the headset again, it will enter pairing mode automatically.

NOTE S:

If the headset is connected with a mobile phone before restoring to original default setting, it will enter pairing mode automatically after restored to default. If the headset is not connected to the mobile phone default setting, it will be in standby mode after restored to default setting.

before restoring to original

13. LED Indication

Headset Status LED Indication

Power Oﬀ Mode R ed LED Oﬀ Power On Power Oﬀ Standby Mode Standby-Low Voltage Talk in progress Mute Pairing in progress Standby

(Disconnect Bluetooth device) Charging in progress Charging completed

Red LED ﬂashes 3 times rapidly Red LED ﬂashes 3 times rapidly

Red LED ﬂashes once every 3 seconds Red LED ﬂashes once every 0.5 seconds Red LED ﬂashes once every 6 seconds Red LED steady on Red LED steady on

Red LED ﬂashes twice every 3 seconds

Red LED steady on Red LED oﬀ

-06-

1. About Bluetooth Technology

Bluetooth wireless technology is set to revolutionize the personal connectivity by providing freedom from wired connections-enabling links and connectivity between notebook/laptop, mobile phones, portable handheld devices and other Bluetooth enabled devices within10 meters. Utilizing global sound & digital data 2.4GHz ISM transmission, it makes global communication in the way you’ve never dreamed of!

2. Getting to Know Your Bluetooth Headset

To use your Bluetooth Headset, please follow these simple steps: (1) Charge your Headset. Prior to using the Headset, it is recommended to charge the battery fully for the first time. Normal full charge time is 2 hrs. (approx.) (2) Place your Headset and a Bluetooth-enabled mobile phone within 1 meter for pairing. (3) Ensure your Headset and mobile phone is placed within 10 meters Bluetooth sensing distance. (Obstruction could cause shorter sensing distance.)

3. Appearance and Function

(1) Speaker (2) Microphone (3) Charging Socket (4) Multi-Function Button (MFB) (5) Volume Increase (V+) (6) Volume Decrease (V-)

-01-

(7) Press “Return” to go back to your mobile phone’s main menu. Place the mobile phone and headset within 10 meters for

recommended sensing distance.

NOTE : If the pairing is not completed within 2 minutes after

mode is activated, the headset will power oﬀ automatically.

You will have to repair the headset using the steps above.

Connection/Link between Headset and Mobile Phone

After pairing is completed, headset will remain in standby mode. Before placeing or answering a call, if the headset icon is not shown on phone screen, follow the steps below to activate the Bluetooth connection/link through the mobile phone or headset until the headset icon is on the screen.

(1) ON PHONE : Select the ”BT Headset” from the paired list on your phone screen.

(2) ON HEA DSET: Press “MFB” and select “Accept” on phone screen to form the

connection.

pairing

8. Disconnection between Headset and Mobile Phone

When you need to connect your headset with another Bluetooth-enabled mobile phone. Follow the steps below to disconnect the headset from the

the pre-paired mobile phone.

(1) Power oﬀ the headset. (2) Select “Disconnect” on the Bluetooth device list of your mobile phone

to remove the connection.

NOTE : When losing the connection/link, the headset will automatically

turn oﬀ in 10 minutes. The red LED will ﬂash twice every 3 seconds when the headset is not connected to mobile phone.

9. Using the Headset

(1) ANSW ERING CALL When receiving a phone call, press the “MFB” button to answer the call. (2) ENDING CALL Press the “MFB” button to end a call. (3) REJ ECT CALL When you hear the ringing tone, press and hold the “MFB” button for 3 seconds to reject the call. (4) VOICE DIAL

If your mobile phone is voice dialing enabled, in standby mode, press the “MFB” button and say the voice tag after you hear a beep. NOTE : Please make sure to record voice tag into the mobile phone before using voice dial function. Functionality varies depending on the mobile phone models. (Refer to your mobile phone owner’s manual.)

-03-

b. MULTIPOINT O FF: In standby mode, press and hold “V-” button

for 6 seconds until you hear a beep. The headset will turn oﬀ

the multipoint function and power oﬀ automatically. When

powering on the headset again, it will only connect to the last

connected Bluetooth device.

(2) Multipoint Pairing

a. FIR ST MOBILE PHONE : Pair the headset with one of the

Bluetooth-enabled mobile phones.

b. SECON D MOBILE PHONE : Power oﬀ the headset. Press and

hold the “MFB” button for 6 seconds to enter pairing mode again

to pair and connect with the second mobile phone.

c. Connect with the ﬁrst paired mobile

(3) Multipoint Connection/Link with 2 Mobile Phones

After the multipoint function is activated, please follow the steps below

to connect with 2 Bluetooth enabled mobile phones at the same time.

a. When power is on the headset, it will automatically search and

connect the last 2 mobile phones that have been connected before.

b. In standby mode, press and hold “V+” button for 6 seconds until

you hear a beep, then the headset will automatically connect the last 2 mobile phones that have been connected before.

(4) Using the Secondary Mobile Phone through Headset

When connected with 2 Bluetooth mobile phones, the ﬁrst connected

e is primary phone that can use “MFB” button for voice dial and redial.

on The second connected phone is the secondary phone that will use “V+” button for voice dialing and redialing.

a. VOICE DIAL : Press “V+” button once to activate the secondary

phone’s voice dialing function.

b. R E-DIALING : Press “V+” button twice to redial the last outgoing

number of secondary phone.

NOTE :

1. When the headset is in Multipoint oﬀ mode and connected with only one

mobile phone, it can also enter voice dial function by pressing the “V+” button once, or make last outgoing number re-dialing by pressing “V+ button twice.

phone to the headset.

”

-05-

14. Product Speciﬁcations

Bluetooth Compliance: Bluetooth V2.1 + EDR Operating Frequency Band: 2.4 GHz ~ 2.48 GHz unlicensed ISM band Output Power: Class 2, up to 10 meters Support Proﬁles: HSP and HFP1.5 proﬁles Support Multiple Paired Device: Memorize paired data of 8 Bluetooth phones (Only 2 connections at any time) Stand-by Time: Up to 200 hours Talk Time: Up to 8 hours Battery Charging Time: About 2 hours Charger Voltage: DC5.0V, 300mA Battery: 85

Manufactured for your Military Exchanges

www.shopmyexchange.com

mAH, (Rechargeable Lithium-ion battery)

Dallas, TX 75266-0202

Printed in China

-07-

Please also inform the grantee, that the regulatory text as shown in the manual provided, is not good. The correct content must be as given below. It is important that they correct this before placing the product on the US and Canadian market.

FCC Information:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the radio or television oﬀ and on, the user is encouraged to try to correct interference by one or more of the following measures:

‐ Reorient or relocate the receiving antenna. ‐ Increase the separation between the equipment and receiver. ‐ Connect the equipment into an outlet on another circuit. ‐ Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.