Sunitec Enterprise BH002 User Manual

MONO HEADSET

User Manual

whenever low battery is encountered. When battery becomes low, LED

will ash red every 3 seconds. Under low battery condition, if headset is

continuously used, it’ll decrease durability of battery as well as standby time and cause longer charge time than normal 2 hrs. Also, the headset will power off.

(3) The red LED will ash on while charging, and blue LED will ash on when

charging is completed.

5. Turning ON/OFF the Headset

Power ON:

When Headset is under off mode, press and hold the “MFB” for 3 seconds until

you hear a short beep. The blue LED will ash 5 times, and then the headset will

automatically connect to the last connected mobile phone. Power OFF: When headset is under standby mode, press and hold the “MFB” button for 3

seconds until you hear a short beep. The red LED will ash 5 times before power

of f.

6. Pairing

Prior to using the headset for the rst time, you must pair it with a Bluetooth-

enabled mobile phone. The steps below describe pairing instructions for a typical Bluetooth-enabled mobile phone.

(1) Place the headset and mobile phone no more than 1 meter apart. (2) Ensure the headset is under OFF mode.

(3) Press and hold the “MFB” button for 6 seconds until the LED ash red and

blue alternatively. It is now ready for pairing.

(4) Activate the Bluetooth function on your mobile phone and search fro

accessible Bluetooth device by referring to your mobile phone user guide for

details. (5) Select “BT Headset” from the list. (6) Enter the pre-programmed code “0000” and press “OK” to pair the headset

and the phone. When pairing is completed, the blue and red LED stop

ashing, the headset is under the standby mode with the blue LED ashes in

every 3 seconds. (7) Press “Return” to go back to your mobile phone’s main menu. Please place

the mobile phone and the headset within 10 meters sensing distance. You

should now be able to make and receive calls using your headset.

Note: If the pairing cannot be completed within 2 minutes after the pairing mode

Please refer to your mobile phone user guide for details.

(5) Last Number Re-Dialing

Under standby mode, short press the “MFB” button twice for last number redial.

(6) Adjusting the Volume

During a call, press the “V+” or “V-” buttons repeatedly until you reach the desired volume level.

(7) Mute & Un-Mute

a. Mute: During a call, press and hold the “V-” button for 3 seconds to

mute the headset. The red LED will ash on during mute mode.

b. Un-Mute: Press and hold the “V-” button 3 seconds to un-mute the

headset.

(8) Transferring Calls

a. Headset to Mobile Phone: During a call, press and hold the “V+” button

for 3 seconds, and the call is routed to your mobile phone.

b. Mobile Phone to Headset: Press and hold the “V+” button for 3 seconds

to route the call to headset.

(9) Hold the Call

During a call, press the “MFB” button twice to hold the phone call. Press “MFB” button twice again to resume conversation.

(10)

Answer the Second Call

a. When receiving a second call, press “MFB” button twice to hold the rst

call on line and answer the second call.

b. When receiving a second call, press “MFB” button once to end the rst

call and answer the second call.

(11)

Reject the Second Call

When receiving a second call, press and hold the “MFB” button for 2 seconds to reject the second call.

(12)

Switch between 2 Phone Calls

a. When having 2 calls on the line, press “MFB” button twice to switch

between these 2 phone calls.

b. When having 2 calls on the line, press “MFB” button once to end the rst

call and stay with the second call.

10. MultiPoint Feature

(1) Activate Multipoint Connection The default setting of Headset’s multipoint function is off. Please act ivate the

time. When one of them receives an incoming call, the other phone will be disconnected from headset but resume connection automatically after the

rst one has nished the phone call.

11. Low Voltage Protection of Battery

When the voltage of battery decreased to 3.3V, the red LED will ash in every 3

seconds, and the headset will be power off automatically when the voltage under

3.0V.

12. Restore to Default Setting

Please follow the steps below to reset the headset to its original setting and remove all the previous pairing and connection.

(1). Ensure the headset is under standby mode. (2). Press and hold both of “V+” and “V-” buttons for 10 seconds until the blue

and red LED flash 5 times, then the headset will resume standby mode. The headset is now back to original setting, and after power on the headset again, it will enter pairing mode automatically.

NOTES: If the headset is connected with a mobile phone before restore to default

setting, it will enter pairing mode automatically after restored to default. If the headset is not connected with the mobile phone before restore to default setting, it will be under standby mode after restored to default setting.

13. LED Indication

Headset Status LED Indication Power Off Mode Off Power On Blue LED ash 5 times rapidly Power Off Red LED ash 5 times rapidly Standby Mode Blue LED ash once every 3 seconds Standby (Disconnect Bluetooth

device)

Blue LED ash twice every 3

seconds Standby-Low Voltage Red LED ash once every 3 seconds Talk in progress Blue LED ash once every 6 seconds Mute Red LED steady on

Pairing in progress

The red and blue LED ash on

alternatively

1. About Bluetooth Technology

Bluetooth wireless technology is set to revolutionize the personal connectivity by providing freedom from wired connections-enabling links and connectivity between notebook/laptop, mobile phones, portable handheld devices and other Bluetooth enabled devices within 10 meters. Utilizing global sound & digital data

2.4GHz ISM transmission, it makes global communication in the way you’ve never dreamed of!

2. Getting to Know Your Bluetooth Headset

To use your Bluetooth Headset, please follow these simple steps: (1) Charge your Headset. Prior to using the Headset, it is recommended to

charge the battery fully for the rst time. Normal full charge time is 2 hrs.

(approx.)

(2) Place your Headset and a Bluetooth-enabled mobile phone within 1 meter

for pairing.

(3) Ensure your Headset and mobile phone is placed within 10 meters Bluetooth

sensing distance. (Obstruction could cause shorter sensing distance.)

3. Appearance and Function

(1) Speaker (2) Microphone (3) Charging Socket (4) Multi-Function Button (MFB) (5) Volume Increase (V+) (6) Volume Decrease (V-)

4. Charging Your Bluetooth Headset

The Bluetooth Headset comes with a builti-in rechargeable battery. Prior to using the headset, it is

recommended to charge the battery fully for the rst time. Normal full charge

time is 2 hrs. (approx.)

IMPORTANT:

(1) Charging indication will be delayed for a few minutes if the headset has not

been used for a long time or the battery is drained.

(2) To prolong durability of battery, it’s recommended to charge the headset

(2)

(3)

(4)

(5)

(6)

BH600E

(1)

1 3

is activated, the headset will power off automatically. Please repeat steps above to pair the headset and mobile phone again.

7. Connection/Link between Headset and Mobile Phone

After pairing is completed, headset is always under standby mode. Before you place or answer a call, if the headset icon is not shown on phone screen, please follow the steps below to activate the Bluetooth connection/link through your mobile phone or headset until the headset icon is on the screen.

(1) On phone: Select the “BT Headset” from the paired list on your phone

screen.

(2) On headset: Short press “MFB” and select “Accept” on phone screen to

accept connection.

8. Disconnection between Headset and Mobile Phone

When you need to connect your headset with another Bluetooth-enabled mobile phone, please follow the steps below to disconnect the headset with the prepaired mobile phone.

(1) Power off the Headset. (2) Select “Disconnecting” on the Bluetooth device list of your mobile phone to

remove the connection.

Note: When losing the connection/link, the headset will be automatically power off in 10 minutes. The blue LED will ash twice in every 3 seconds when the

headset is not connected with mobile phone.

9. Using the Headset

(1) Answering Call

When receiving a phone call, Press the “MFB” button to answer the call.

(2) Ending Call

Press the “MFB” button to end a call.

(3) Reject Call

When you hear the ringing tone, Press and hold the “MFB” button for 3 seconds to reject the call.

(4) Voice Dial

If your mobile phone is voice dialing enabled, under standby mode, short press the “MFB” button and say the voice tag after you hear a beep.

Note: Please make sure to record voice tag into the mobile phone before using

voice dial function. Functionality varies depending on the mobile phone models.

multipoint function for connecting with 2 mobile phones in the same time. a. Multipoint On: Under standby mode, press and hold “V+” button for 10

seconds until you hear a beep. After turn on the multipoint function, the headset will automatically connect to the last 2 mobile phones that has been paired before.

b. Multipoint Off: Under standby mode, press and hold “V-” button for 10

seconds until you hear a beep. The headset will turn off the multipoint function and power off automatically. When power on the headset again, it will only connect to the last connected Bluetooth device.

(2) Multipoint Pairing

a. First mobile phone: Pair the headset with one of the Bluetooth-enabled

mobile phone.

b. Second mobile phone: Power off the headset. Press and hold the “MFB”

button for 6 seconds to enter pairing mode again to pair and connect with the second mobile phone.

c. Connect with the rst paired mobile phone to the headset.

(3) Multipoint Connection/Link with 2 Mobile Phones

After the multipoint function is activated, please follow the steps below to connect with 2 Bluetooth enabled mobile phones in the same time.

a. When power on the headset, it will automatically search and connect the

last 2 mobile phones that have been connected before.

b. Under standby mode, press and hold “V+” button for 3 seconds until

you hear a beep, then the headset will automatically connect the last 2 mobile phone that have been connected before.

(4) Using the Secondary Mobile Phone through Headset

When connected with 2 Bluetooth mobile phones, the rst connected one

is primary phone that can use “MFB” button for voice dial and redial. The second connected phone is secondary phone that will use "V+" button for voice dial and redial.

a. Voice Dial: Press “V+” button once to activate the secondary phone's

voice dialing function.

b. Re-Dialing: Press “V+” button twice to redial the last outgoing number of

secondary phone.

Note:

When the headset is in Multipoint off mode and connect with only 1 mobile phone, it can also enter voice dial function by press “V+” button once, or make last outgoing number re-dialing by press “V+” button twice.

2. The Multipoint headset can be paired with 2 mobile phones at the same

Charging in progress Red LED steady on Charging completed Blue LED steady on

14. ProductSpecication

Bluetooth Compliance: Bluetooth V2.1+EDR Operating Frequency Band: 2.4GHz ~ 2.48GHz unlicensed ISM band Output Power: Class 2, up to 10 meters

Support Proles: HSP and HFP 1.5 Proles

Support Multiple Paired Device: Memorize paired data of 8 Bluetooth phones (Only 2 connections at any time)

Stand-by Time: Up to 150 hours Talk Time: Up to 6~8 hours Battery Charging Time: About 2 hours Charger Voltage: DC 5.0V, 300mA Battery: 85mA (Rechargeable Lithium-Ion Battery)

FCC Warning: This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) The device may not cause harmful interference, and (2) This device must accept any interference received, including interference

that may cause undesired operation. Changes or modification not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. FCC Radio Frequency Exposure statement: This product has been evaluated under FCC Bulletin OET 65C and found

compliant to the requirement asset as set forth in CFR 47 section 1.1307(b),

2.1093 and 15.247(i) addressing RF Exposure from radio frequency device, the redialed output power of this product is far below the FCC radio frequency exposure limits.