Sunitec Enterprise BC013 User Manual

PowerBlue PBC10

User Manual

(4) Red LED stays on when PBC10 is charging, Red LED turns to off when Battery

is fully charged.

(5) Low Voltage Reminder: Red LED ﬂashes every 3 seconds when Bluetooth is on,

and Voltage Low. Please charge the battery to maintain battery efﬁciency.

Important:

PBC automat ically turns off if devi ce is not charged after L ow Voltage Reminder indication shows up.

PBC10 Charges other devices:

(1) Split LED ﬂashlight apart from PBC10 (2) Connect USB A type to P BC10, connect the other end to other devices(c ell

phone, IPod)

(3) Press ON/OFF key to launch charging function. When Green light stays ON, cell

phone and IPod are being charged via DC 5V.

Important:

1. Charg ing function i s ende d and Green light is OFF when PBC10 does not connect to anything.

2. In the Chargi ng acti ons, PB C10 au tomatically stops out-put DC 5 V when cell phone, IPod is either disconnected or fully charged, and Green lig ht (Some devices are pr ogrammed to c hoose being charged even if the b attery is already fully charged, in that case, PBC10 will NOT stop charging and Green light will stay on until PBC10’s battery is dead.)

Installing

is OFF.

(5) Select “Speakerphone” from the list. (6) Enter the

(7) Press “Return” to go back to your handset’s main menu. (For most of the

Important: Under th e pairing mode, if the pair ing cannot be completed within 2 minutes, the

PCB10’s LED will ﬂash off and PCB10 will be under off mode. Please repeat step (3) to (7) to pair the pcb10 and mobile handset again.

Connection/Link between Speakerphone and Mobile Handset

After pairing is completed, speakerphone is always under standby mode. place or answer a call, if the headset ICON is not shown on phone screen, pl ease follo w the simple steps to activate the Bluet ooth connect ion/l ink through your handset or speakerphone until the headset ICON is on the screen.

1. On Handset: Select “ Speak erpho ne” from the paired list on yo ur handset

2. On Speakerphone: Short press MFB and select “Accept” on handset screen to

Disconnection between Speakerphone and Mobile Handset

Please follow the steps below if you want to connect PCB10 to another cell phone. (a) Power off the PCB10. (b) Select “disconnecting” to remove previous connection from your mobile pho ne

Important: To save energy, PCB10 automatically turns OFF 10 minutes after disconnection. Blue LED ﬂashes 3 times every 2 seconds if PBC10 is not connected to any mobile.

Answer Incoming call:

To answer a call, wait fo r the speakerphone to ring, then short press the MFB to accept the call.

pre-programmed password “0000” and press “OK” to pair the PCB10

and the handset. When pairing is completed, you may hear a long beep and LED will ﬂash blue

3 times. Now the PCB10 is under standby mode with Blue LED ﬂashes every 3 seconds.

mobile h andset models, a head set icon wi ll be shown o n the screen.) You should now be able to make and receive calls through the PCB10. Please place the mobile handset to the PCB10 no more than 10 meters. (Obstruction could cause shorter sensing distance.)

Before you

screen.

accept connection.

list.

Answer incoming call during a call activity:

A. During a call activity, press MFB button twice quickly to answer incoming call

and meanwhile hold ﬁrst line.

B. Press MFB button once to end ﬁrst line and answer s

Reject incoming call during a call activity:

During a call activity, press and hold MFB for 3 seconds to reject incoming call.

Switch Calls:

Press MFB twice quickly to switch between two lines. Press MFB once to end call one line to continue with the other line.

Play and Pause Music:

Press MFB to Play and Pause music

Important:

Some cell phones do not play music in standby mode.

Select previous and next song:

During playing music, press V- or V+ on PBC10 to roll to previous or next song.

Reset:

Reset PBC10 will format pairing history.

1. Make sure PBC10 is in standby mode.

2. Press and hold V+ and V- for 10 seconds, Red and Blue LED fla sh 5 t imes together at the same time. After PBC10 is rested, PCB10 automatically restart and start pairing mode.

Maintenance: Care and Maintenance

(a) Do not expose the s peakerphone to liquid, moisture or humidity, as it is not

waterproof.

(b) Do not use abrasive cleaning solvents to clean the speakerphone. (c) Do not p lace the sp eakerph one in high te mperatur e, as it will result in an

explosion.

(d) Do not expose t he speakerp hone to cont act with sharp objects as th is will

cause scratching and damage.

econd line.

FCC Information:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B Digital

Device, pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the radio or television off and on, the user is encouraged to try to

correct interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on another circuit.

- Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

Introduction:

PBC10 is a portable Flashlight and Emergency power bank with Bluetooth Handsfree A2DP device, which is ba sed on DSP with echo cancela tion and noise reduction. PBC10 is handy in any environment such as ofﬁce, home, or in the car. PBC10 is able to connect to any mobile cell phone that supports Bluetooth. New Bluetooth version impels s table and st eady Wireless connection with high speed and high qu ality AD2P+AVRCP. PBC10 has a 2100mAh built-in chargeable ly-polymer battery with an USB Out-put port switching regulator 5V DC/DC. PBC10 is an efﬁcient charger and

bright LED ﬂashlight.

Appearance and Function

(1) Speaker (2) Microphone (3) LED (4) Charging Socket (USB) (5) On/Off LED Flashlight Button (6) MFB Button (Multi-Function Button) (7) Volume Increase (V+) (8) Volume Decrease (V-) (9) LED Flashlight

Package content:

- PBC10 3-in-1 Device

- USB Cable

- Holder

- User Manual

- Sun Visor Clip

Power Bank Charging Instruction Charge PBC10:

(1) Split LED ﬂashlight apart from PBC10 (2) Put charger Jack into PBC10’s in-put (3) Charging takes no longer than 3 hours

(4)

(3)

(7)

(6)

Optional

USB AC Charger

PBC10

(9)

(2)

(5)

(8)

(1)

Optional Speaker

Flash light ON/OFF Instruction:

(1) Make sure ﬂashlight is completely mounted. (Head part) (2) Press ON/OFF to turn ﬂashlight ON. (3) Press ON/OFF to turn ﬂashlight OFF, or split ﬂashlight apart from PBC10.

Bluetooth Handsfree Launch and A2DP+AVRCP Instruction Turn on Bluetooth: PBC10 is under OFF mode

Press and hold MFB for 4 seconds until you hear a short beep, and then Blue LED will stay ON for 3 seconds.

PBC10 will automatically reconnect to the last mobile phone it paired.

Turn OFF Bluetooth: PBC10 is under ON mode

Press and hold MFB for 3 seconds until you hear a short beep, and then Red LED will stay ON for 3 seconds.

Pair PBC10 to your mobile phone

Prior to using the speakerphone for the ﬁrst time, you must pair it with a Bluetoothenabled mobile:

(1) Place the PCB10 and mobile handset no more than 1 meter away. (2) Ensure PBC10 is under OFF mode. (3) Press and hold the MFB for 6 seconds until you hear a long beep. The Red LED

and Blue LED will ﬂash alternately. It’s now ready for pairing.

(4) Activate your mobile handset’s Bluetooth function by referring to your mobile

han dset use r guide for detail s. Mean whil e, the handse t will search for accessible Bluetooth devices.

Hang Up call:

Press the MFB to end call.

Reject Incoming Call:

Press MFB for 3 seconds to reject incoming call.

Voice Dial:

In standby mode, press V+ twice quickly, when we hear the beep from PCB10, say the voice tags.

Important: Please make sure to record voice tag into the mobile handset befor e us ing voice

dialing function. This function is only ap plicable to m obile h andset with B luetooth Hands-Free Proﬁle. Some phones, we may not hear the beep. Please refer to your mobile handset user guide for additional information.

Redial:

Press MFB twice quickly, PCB10 redials the last number it called out.

Volume Adjustment:

During a call activity or playing music, click V+ or V- to adjust volume.

Mute Microphone:

A. Mute: Press and hold V- for 3 seconds to mute microphone, PCB10’s Red LED

stays ON

B. Un-Mute: Press V+ for 3 seconds to un-mute.

Call Transfer:

A. PCB10 to Mobile Phone: Press V+ and V- at the same time (during a call) to

transfer voice from PCB10 to cell phone. Talk on the Mobile.

B. Mobile ph

Make call waiting:

During a call activity press MFB button twice quickly to Hold and Un-Hold call.

one to PCB10: Press V+ and V- at the same time (during a call) to

transfer voice from cell phone to cell phone. Talk through PBC10.

(e) Do not stick anything insid e th e s peakerphone as this may damage internal

components.

(f) Do not a ttemp t to di sasse mble t he speakerp hone, as it do es not c onta in

serviceable components.

(g) If you do not use the speakerphone for long periods, be sure to store it in a dry

place, free from extreme temperature, humidity and dust.

Safety Information:

(a) Check local laws regarding use of a mobile handset and speakerphone while

driving. If you use the speakerphone while divi ng, ensure your attention and focus remains on your responsibility of driving safety.

(b) Never allow c hildren t o play with the s peakerp hone. Small p arts may be a

choking hazard.

(d) Turn o ff your speakerphone p rior to boa rding an air craft. Do not u se your

(e) Never mount or store your speakerphon e over any air bag deploy ment area

Product Speciﬁcations:

Bluetooth Speciﬁcation: V2.1 + EDR Frequency Working Range: 2.402GHz ~ 2.480GHz unlicensed ISM band Output Power: Level 2, Maximum connection distance: 10 meter Supported Proﬁle: HSP, HFP 1.5, A2DP and AVRCP Proﬁles Standby time: 152 days Talk time: 44 hours Music Play time: 25 hours Charge time: approximately 3 hours Flashlight last: 6 hours Charging input Voltage, electric current: DC 5.0V 2000mA Charging output Voltage, electric current: DC 5.0V 500mA Battery Capacity: 3.7V 2100 mAh Dimension: 113g Weight: L150*Ø35.6mm

si gns t hat require an electrical device or RF radio product to be switched off in t he de signated areas. These could include hospitals, blas ting areas, and potentially explosive atmospheres.

speakerphone in an aircraft.

serious injury may result when an air bag deploys.

1 3