Sunitec Enterprise BC012 User Manual

"SOLAR-POWERED"

Text To Speech

SPEAKERPHONE

User Manual

WARNING: Do not place or store the speakerphone over the area of the automobiles safety airbag deployment, or it may cause serious injury when a safety airbag deploys.

4. Charging Your Bluetooth Speakerphone

The Bluetooth speakerphone comes with a built-in rechargeable battery. Prior to using the speakerphone, it is recommended to charge the battery fully for the first time.

Using the car charger

• Insert the car charger completely into the charging slot until the red LED goes on.

• Normal full charge time is 2 hours. (approx.), and the red LED goes off when charge

is completed.

Using solar power

• Direct the solar panel on the back side of the speakerphone toward sun. (Please refer to the recommended installation position, as mentioned above.)

• If the speakerphone receives sufficient sunlight for 2 hours, you can talk for duration of up to 1 hour. Using solar power charge, the operation time (the talk time and the standby time) will be extended continuously without any additional charge required by the car charger.

WARNING: Do not attempt to charge the speakerphone with any charger other than the one provided. Using another charger may damage or destroy the speakerphone.

5. Turning On/Off the Speakerphone

(1) To turn ON the Speakerphone

Press and hold the “MFB” button for four seconds and the blue LED flashing 3 seconds light indicator comes on (“Power On” is announced).

(2) To Turn OFF the Speakerphone

Press and hold the “MFB” button until the red LED flashing 3 second s light indication goes off (“Power Off ” is announced).

6. Pairing

Prior to using the speakerp hone for the first time, you must pair it with a Bluetooth-enabled mobile ph one. The steps below descri be pairing instructions for a typical Bluetooth-enabled m obile phone.

epeat the process for turning speakerphone on.

2. If your speakerphone is set as an authorized Bluetooth device on your mobile phone, an automatic reconnection can be established by pressing the speakerphone’s “MFB” button once.

8. Using the Speakerphone (Most 0functions will be audibly announced)

(1) Answering a Call

When your mobile phone rings, press the “MFB” button on the Speakerphone to

connect the call.

(2) Making Calls from your mobile phone Dial directly from your mobile phone. The call

is automatically connected to your Speakerphone.

(3) Reject a Call

Hold onto the “MFB” button for 3 seconds to reject an incoming call.

(4) Ending Calls

When you have finishe d you r cal l, press the “MF B” button on the rece iver to disconnect the call.

(5) Making calls using voice dialing (Dependent on mobile phone support) Press the “MFB”

button once and call out the name of the person for the call to be placed.

(6) Redial Last Outgoing Call

Press the “MFB” button twice and the call is connected.

(7) Transfering Calls

a. Speakerphone to Mobile Phone: During a call, short press both “V+” and “V-”

buttons, and the call is routed to your mobile phone.

b. Mobile Phone to Speakerphone: Short press the “MFB” button or both “V+” and

“V-” buttons once to route the call to speakerphone.

(8) Adjusting The Volume

To inrease the volume - Press the “V+” symbol volume button to increase volume by

e level, repeat this procedure until you have reached the desired level. To decrease

Removing Phonebook Entries

(13)

Dur ing stand by mode, hol d on to both “V+” and “V- ” button s for 3 second s (“Phon ebook Delet ed” is ann ounce d) and the entire phone book memory in the Speakerphone will be deleted.

14)

Turning On/Off the Text-To-Speech Function

(

To toggle the TTS function On or Off, simply hold the “V+” for 6 seconds in standby mode (“Voice Prompt On” or “Voice Prompt Off” is announced to denote its current status).

9. Low Voltage Protection of Battery

When the voltage of battery decreased to 3.3V, the red LED will ﬂash in every 3 seconds, and the Speakerphone will be power off automatically when the voltage under 3.0V.

10. Restore to Default Settings

To restore your speakerphone to its original settings, press and hold both “V+” and “V-” buttons for 10 seconds until the blue LED light indication ﬂashes rapidly. Press and hold both “V+” and “V-” buttons for a further 3 seconds and the speakerphone will power off automaticall y. This process is completed wh en speakerphone an nounces “Set Factory Default Completed”. When power on the spea automatically.

12. Care and Maintenance

(1) Do not expose the speakerphone to liquid, moisture or humidity, as it is not

waterproof. (2) Do not use abrasive cleaning solvents to clean the speakerphone. (3) Do not expose the speakerphone to extreme temperatures. (4) Do not expose the speakerphone to contact with sharp objects as this will cause

scratching and damage. (5) Do not attempt to disassemble the speakerphone, as it does not contain serviceable

components. (6) If you do not use the speakerphone for long periods of time, be sure to store it in a

dry place, free from extreme temperatures, humidity and dust.

13. Safety Information

(1) Check local laws regarding use of a mobile phone and speakerphone while driving. If

you use the speakerphone while diving, ensure your attention and focus remains on

kerphone, it would be in the pairing mode

FCC Information:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the radio or television off and on, the user is encouraged to try to correct interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on another circuit.

- Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

1. About Bluetooth Speakerphone

The Bluetooth TTS Speakerphone is compatible with most Bluetooth mobile phones. The Text-To-Speech system an nounces instructions for the users in 5 different la nguages and also indicates the status of the Bluetooth device. It also announces the name of the incoming caller (or phone number if the contact is not loaded into the Speakerphone’s phonebook). Fully p ortable, i t is an ideal wireless com munication solution for in-car or ofﬁce use within a maximum range of 10 meters. Built-in with Echo Cancell ation and Noise Suppress ion, the Bluetoo th Speakerphon e p rovides you with impeccab le sound quality in full duplex mode.

Make sure that your Speakerphone is fully charged before using it. Use only the charger provided - do not use chargers from any other devices as this might damage the device. A full charge is approximately 2.5 hours.

2. Appearance and Function

(1) Speaker (2) Microphone (3) LED (4) Charging Socket (5-pin USB) (5) MFB Button (Multi-Function Button) (6) Volume Increase (V+) (7) Volume Decrease (V-) (8) Solar Panel

3. Recommend Installation Position

It is recommended that the speakerphone is positioned on to the top of the left side of the windshield as shown in the pictures below:

41 2 3

(8)

(7)

TEXT TO SPEECH

(6)

(2)

(4)

(3)/(5)

(1)

instructions for a typical Bluetooth enabled mobile phone. (1) Place the speakerphone and mobile phone no more than 1 meter (3 feet) apart. (2) Ensure the speakerphone is turned off. (3) Press and hold the “MFB” button for 6 seconds until the LED ﬂash red and blue

alternatively, it is now ready for pairing. (“Pairing phone please put your phone in pairing mode and enter PIN code “0000” is announced).

(4) Activate the Bluetooth function on your mobile phone and search for accessible

Bluetooth device by referring to your mobile phone user guide for details. (5) Select “BT Speaker” from the list of searched devices. (6) Enter the pre-programmed code “0000” and press “OK” to pair the speakerphone

and the phone. (7) When pairing is completed, the speakerphone is under the standby mode with

the blue LED ﬂashes in every 3 seconds. Please place the mobile phone and the

speakerphone within 10 meters (32 feet) sensing distance. (“Pairing Successful” is

announced). NOTE:

1. If the pairing cannot be completed within 2 minutes after the pairing mode is

activated, the speakerphone will power off automatically. Please repeat steps above

to pair the speakerphone and mobile phone again.

2. When ﬁrst time using the speakerphone and after restore to default settings, the

speakerphone will automatically enter pairing mode after power on.

7. Connection Link/Between Speakerphone And Mobile Phone

After pairin g i s completed, sp eakerphone is always u nder standby mode. Be fore you place or answer a call, if the headset icon is not shown on phone screen, please follow the steps below to activate the Bluetooth connection/link through your mobile phone or speakerphone until the headset icon is on the screen.

• On phone: Select the “BT Speaker” from the paired list on your mobile phone’s

Bluetooth menu.

• On speakerphone: Short press the “MFB” and select “Accept” on phone screen to

accept connection. NOTE:

1. Your speakerphone will be automatically switched off when it is disconnected from

a paired device for more than 10 minutes. This special feature is incorporated to

maximize your speakerphone’s standby/talk time. To reinstate the connection, simply

the volume - Press “V-” symbol button to decrease the volume by one level, repeat this procedure until you have reached the desired level.

(9)

Answer/Reject the Second Call during a Call

a. Answer: When receiving a second call, short press the “MFB” button once to hold

the ﬁrst call on line and answer the second call.

b. Reject: When recei ving a second call, p ress and hold the “MFB” butt on for 3

seconds to reject the second call.

(10)

Switch between 2 Phone Calls

a. When having 2 calls on the line, press and hold the “MFB” button for 3 seconds

to switch between these 2 phone calls.

b. When having 2 calls on the line, short press

ﬁrst call and stay with the second call.

(11)

Text-To-Speech Language Options

The speaker phone is availabl e in 5 languag e options. D uring the stand by mode, press the “V+” b utton for 3 secon ds until the bl ue LED flashes 3 times and the speakerphone announce “Select Language”. Repeat this process to select the desired language in the following order of English, French, Italian, German and Spanish.

(12)

Transferring Mobile Phone’s Phonebook to Carkit (*Handset Dependent)

1. In the co nnect ed status, press the “V-” button for 3 sec onds until the b lue LED ﬂashes 3 times, and the Blue LED light indica tor comes on. This process automatically extracts the mobile phone’s phonebook memory.

2. When the proc ess is completed, the Carkit announce s “Contac ts Saved”. The process may take a few minutes depending on the amount of contacts that is being stored in the mobile phone’s memory.

NOTE:

1. If the phonebook transfer is failed, the speakerphone will announce “Loading phonebook failed”. The phonebook function varies from different mobile phone models, and not every mobile phone supports this feature. Please check with your supplier whether your mobile phone model support this feature.

2. The phonebook data saved in the speakerphone will be erased automatically when it is paired with another mobile phone.

3. Before transferring Phone's Phonebook, When incoming call, you will hear” Call from (Number)”,and if Contacts Saved OK, when incoming call, you will hear “Call from (Name)”.

the “MFB” button once to end the

your responsibility of driving safety.

(2) Never allow children to play with the speakerphone. Small parts may be a choking

hazard.

(3) Observe all signs that require an electrical device or RF radio product to be switched

off in the designated areas. These could include hospitals, blasting areas, and potentially explosive atmospheres.

(4) Turn off your speakerphone prior to boarding an aircraft. Do not use your

speakerphone in an aircraft.

(5) Never place or store the speakerphone over the area of the automobile's safety

airbag deployment, or it may cause serious injury when a safety airbag deploys.

14. Product Speciﬁcations

Bluetooth Compliance: Bluetooth 2.1+EDR speciﬁcations Operating Frequency Band: 2.4GHz ~ 2.48GHz unlicensed ISM band Output Power: Class 2 Power Output, up to 10 meters Support Proﬁles: Headset and Handsfree 1.5 Proﬁles TTS Support Language: English, French, Italian, German, Spanish Integrated phonebook: Stores up to 1000 contacts Voice to announce CallerID Support Multiple paired Device: Up to 8 Bluetooth Phone can be paired Stand-by Time: Up to 250 hour Talk time: Up to 6 - 8 hours Battery Charging Time: About 2.5 hours , using solar power about 9 hours Charger Voltage: DC5.0V 400mA Battery Type: 3.7V 340mA (Rechargeable Li-ion Polymer Battery)

NOTES: This speakerphone is in compliance with the speciﬁed Bluetooth version. It does not g uarantee compatibility of all functions on e very B luetooth enabled device. Please check with your mobile phone's user manual for compatibility and functionality.

1 3