Sunex 8013ADELUXE, 8013ABKDELUXE, 8013ABLDELUXE Operating Manual

8013ADELUXE/8013ABKDELUXE/8013ABLDELUXE Rev. A

7/3/14

MODEL 8013ADELUXE, 8013ABKDELUXE,

8013ABLDELUXE Rev. A SERVICE CART

GUARANTEED TO PERFORM

OPERATING MANUAL

Read and follow all instructions in User's Manual. It is the responsibility of the owner to make sure all personnel
read this manual prior to using the device. It is also the responsibility of the device owner to keep this manual intact

and in a convenient location for all to see and read. If the manual or product labels are lost or not legible, contact

Sunex Tools® for replacements. If the operator is not fluent in English, the product and safety instructions shall be
read and discussed with the operator in the operator's native language by the purchaser/owner or his designee,
making sure that the operator comprehends its contents.

PARTS LIST

Examine box contents, then proceed with following instructions.

INCLUDES PRY BAR HOLDER AND SIDE WORK BENCH

WITH LOCKING TOP & DRAWERS

Bottom Tray

Chrome Legs (2)
(With Inserts Installed)

Long Drawer Handle (1)

Drawer Handle
Screws (14)

Keys
(Attached
to Legs)

Short Drawer Handles (4)

Locking Casters (2)Non-Locking Casters (2)Locking Drawer Assembly

M6x42 Bolts,
Nuts, & Washers
(8 Pcs. Each)

Pry Bar Holder

Side Work Bench

TOOLS NEEDED

WARNING

Read and follow all instructions in User's Manual. • Do not load
carts beyond rated capacity (350 lbs.). • Lock lid and drawers before
moving. • Apply brake on locking casters anytime cart is in place.

• Units can tip or fall causing damage or personal injury. • Cart is

designed to roll easily on flat surfaces and should not be used on

uneven or inclined surfaces. • Do not open more than one
loaded drawer at a time. •Do not stand on or step in drawers. • Keep
children away from unit. • Wear gloves when lifting edges. • This
product may contain one or more chemicals known to the State of
California to cause cancer and birth defects or other reproductive
harm. Wash hands thoroughly after handling. • Failure to heed these
warnings may result in personal injury and/or property damage.

Rubber Mallet

Table or Workbench

6mm WrenchPhillips Head

Screwdriver

2 People

© Copyright 2014, Sunex Tools

®

ASSEMBLY INSTRUCTIONS

NOTE

Do not fully tighten fasteners
until prompted.

Step 1: Assembly preparation.

Clear table top and set Locking Drawer Assembly
on table top, with lid facing up. Position the Locking
Drawer Assembly so that one end hangs off of the
table enough to allow the chrome legs to go through
the square holes. Insert one set of chrome legs
through the overhanging holes as shown in Figure 1.
Do not bolt legs to top.

1.

Locking

Drawer Assy.

Table or

workbench

Locking

Top

Chrome

Legs

Step 2: Connecting legs and side
accessory to drawer assembly

Choose one of the side accessories (Pry Bar Holder
or Side Work Bench - Figure 2 shows Pry Bar Holder)
for attachment to the overhanging end of the service
cart. Align the outermost bolt holes in the accessory
with the bolt holes in the end of the cart and with
the uppermost holes in the chrome legs. Position a
washer and insert a 6mm bolt through the washer,
bolt holes, and legs as shown. Secure bolts with
a flat washer, lock washer, and nut on inside of
Locking Drawer Assembly. Tighten bolts until parts
fit together firmly.

Repeat steps 1 and 2 for other end of cart,
using remaining side accessory.

2.

Locking

Top

Locking
Drawer Assy.

Chrome

Legs

6mm

Bolt

8013ADELUXE/8013ABKDELUXE/8013ABLDELUXE Rev. A

Table or

workbench

Pry Bar

Holder

2 7/3/14