Sundrax Splitter PRO, Splitter DUO PRO, SPP-X-1D5D, SPP-X-1D10D, SPPD-X-3D8D User Manual

User manual

DMX
Splitter PRO
Splitter PRO DUO

SPP-X-1D5D, SPP-X-1D10D, SPPD-X-3D8D

Version 1.02

January 17, 2017

1
1
2
2
3
4
6
7

Table of contents

Visual appearance
Specifications
Safe operation
General information
Installation
Connection scheme
Technical maintenance
Notes

1

1 Input indicators 2 Common input 3 Input A
4 А1...А4 inputs 5 Input B 6

В1...В4 outputs

7 1...10 outputs

51 2 3 4 6

1 2 7

Visual appearance

Pic.1 Main interfaces and indicators

Specifications

Supported protocols DMX512, RDM
DMX data refresh rate 44 Hz
DMX input ports 1 or 3 isolated
DMX output ports 5,8 or 10 isolated
DMX connectors XLR (5 pins, 3 pins) or RJ-45 (etherCON)
Mounting Rack
Power supply

~90-250 VAC, 50/60 Hz

Mains Fuse 0.5 A
Input power 5 W
Operating Temperature: -0°С... +60°С
IP Rating IP 20
Dimensions, mm 482(D) x 44(H) x 110(W)

Splitter PRO and Splitter DUO PRO devices designed for split-

ting and elongation DMX lines. Modification with one input signal

allows to get five or ten output signals. Modification with three in­put signal can work both in dual channel mode (each of two input
signals can be splitted to four outputs), and in common input mode
(one input signal can be splitted to eight outputs). Switching be­tween modes occurs automatically in the presence of a signal on
any input port. When the signal is present on common input «IN
COM» and on section input «IN A» or «IN B», section input has a
priority.

2

Key features:

• All input and output channels have galvanic isolation.

• Power consumption is less than 3W.

• RJ45 or XLR connectors

Safe operation

WARNING!

The device uses hazardous voltage AC 230 V

In installation, operation, preventive maintenance and repairs of
the device, the requirements of the safety rules must be followed.

To ensure safe and reliable operation of the devices, please ob­serve the following requirements:

• Use the device only for its intended purpose;

• Do not use devices that shows signs of malfunctioning;

• Avoid strong physical impacts on the device;

• Protect devices and cables from contact with corrosive liquids.

Whenever a fault is detected in the device, please contact the
manufacturer.

General information

3

1. Ensure the device has no damage due to transportation.

2. Install the unit into the rack and secure it with screws. Connect

the power cable plug to a power outlet.

3. Connect cable to input port «IN» if you use «Splitter PRO» de­vice or to necessary input port (IN COM, IN A or IN B) if you use
«Splitter PRO DUO» device. If the input signal is present, the appro­priate port indicator lights. If there is no signal, the indicator flashes.

4. Connect the desired number of output lines to the connectors
«OUT».

5. The device is ready for use.

Device modifications:

SPP

5

Connectors type:

0- wires

1- terminal block

3- 3pin XLR
5- 5pin XLR

6- etherCON

3 D 8 D

DMX inputs:

1, 2 or 3

DMX outputs:
4, 5, 8 or 10

Series:

SPSD- Solid DUO (IP 44)

SPA- Arma (IP 65)

SPP-Pro(DUO) (IP 20)

WSPP-Wireless Pro (IP 20)

SPDD- DIN DUO (IP 20)

AC

Power Supply:

AC or DC

Input type:

D- DMX

B-BeDMX

Installation

Before mounting and power up, it is necessary to verify protec-

tive earthing and cable connections.

4

DMX

DMX

DMX

DMX

Splitter PRO

Device with one input

Connection scheme

5

DMX A

DMX B

Splitter PRO DUO

SECTION A

SECTION B

DMX A

IN COM

(SECTION A+SECTION B,

BACKUP)

DMX A

DMX B

DMX B

Device with three inputs

6

Technical maintenance

Maintenance the device, search and troubleshooting should be
performed by service personnel. The device should be free from
dirt, dents, connecting cables and wires must be intact and securely
fastened.

7

Notes

8

Please send all your warranty-related questions to

[e-mail]

All Sundrax products are covered by a 36 months warranty.

Sundrax Electronics,
6008, First Central 200
2 Lakeside Drive, Park Royal, London
NW10 7FQ United Kingdom
+ 44 (0) 208 991 33 19
[e-mail]
www.sundrax.com