Suncon Toys Industry 200080 Users manual

It’s the ultimate radio control experience! Your Starter Kit comes with a radio controller and a full set of
factory parts to assemble your car. With a quick charge about 60 seconds, your ZipZaps micro RC will
be revving in no time.
Your ZipZaps micro RC provides totally 6 selectable channels. Y ou can enjoy racing with 6 cars a time.
Your ZipZaps micro RC comes with a built-in Ni-MH rechargeable battery to power the car, and it
requires four AAA batteries (not supplied) for the controller/charger.
Built to 1:64 scale, your tunable ZipZaps micro RC is small enough to carry in your pocket. ZipZaps are
perfect for anyone ages 8 and up.
To really rev up the fun factor, you can customize your ZipZaps micro RC with optional performance
upgrade kits, available at the ZipZaps Showroom at www.zipzaps.com

(Please confirm this) and your

local RadioShack. Just follow these steps to get your car up to speed and ready to race.

1 Starter Kit Includes

Your ZipZaps micro RC Starter Kit includes everything you see here:

ON OFF

RELEASE

Factory parts.eps here

2 Attach the WRIST STRAP

Attach the WRIST STRAP as shown below to prevent dropping your CONTROLLER. Thread the string
through the hole on the left side of the CONTROLLE R as show, and then thread the strap through the
ring of the string.

OPEN

ON OFF

ON OFF

ON OFF

OPEN

Attach strap. eps here.

3 Powers Up Your Controller

The CONTROLLER ch arges your micr o RC and contro ls its steering an d speed. You’ll need to install
four AAA batteries. For the best performance and longest life, the ZipZaps factory recommends
RadioShack Enercell Plus alkal ine batter i es.

1) Set ON/OFF on the CONTROLLER to OFF.

2) Slide the battery compartment cover in the direction of the arrow to remove the cover.

3) Insert four AAA batteries in the compartment accordi ng to the polarity symbols (+ and -) marked
inside.

4) Replace the cover and snap shut.

If you notice the LED of your CONTROLLER dimming, it is time to replace the batteries.

Installing batterys.eps here.

Installing Batteries Cautions:

Use only fresh batteries of the required size and recommended type.
Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or
rechargeable batteries of different capacities.
If you do not plan to use the micro RC for a week or more, remove all the batteries from the
CONTROLLER. Batteries can leak chemicals that can destroy electronic parts.
Never leave dead or weak batteries in the CONTROLLER.
Dispose of dead batteries promptly and properly; do not burn or bury them.

4 Zip Your Car Together

1) Mount the HUBCAPS to the front axle wheels, and then press the TIRES over the HUBCAPS as
shown.

Mount front axle wheels.eps

2) Install the STOCK MOTOR WITH DRIVE GEAR in the groove on the back of the CHASSIS.

3) Carefully snap the MOTOR CLIP WITH SET SCREW into the groove closest to the MOTOR as
shown.

Install motor1.eps

4) Rotate the MOTOR CLIP WITH SET SCREW as shown below to set the MOTOR in position.

Install motor2.eps,

5) Secure the MOTOR CLIP WITH SET SCREW with the SCREWDRIVER which is stored at the
bottom of the CONTROLLER.

6) Plug the TRAN SFER GEAR i nto t he ax le as sh own. Be su re th e TRANS FER GEA R me shes with t he
DRIVE GEAR on the STOCK MOTOR.

installs motor3.eps

Caution: Do not over tighten the SET S CREW until the MOTOR CLIP WITH S ET SCREW becomes
slanted. It should be horizontal.

Caution.eps

7) Plug the HUBCAPS in to the REAR AXLE GEAR, and the n press the TIRES over the HUBCA PS.
Next, secure the REAR AX LE GE AR ass embly into the CHASSIS as show n. Be su re the REAR A XLE
GEAR meshes with TRANSFER GE AR.

Mount rear axle wheel.eps