Sunbeam Pets SBRTT2 Instruction Manual

Download

Page 1

rechargeable

remote trainer

INSTRUCTION MaNUal

STaTIC

FCC STATEMENT

Potential for Radio/Television Interference

All rights re served. Dist ributed by Sunbeam® Pr oducts, Inc. do ing business as Jarde n

Consumer Solu tions, Boca Rato n, Florida 33431.

Printed in Chi na SPR-0912-571P PN 147950 SBRT SS2

1 YEAR WARRANTY

In the U.S.A. and Canada If you have any question regarding this warranty or would like to obtain warranty service, please call 1-866-537-2249 and a convenient service center address will be provided to you.

Sunbeam® Products, Inc. doing business as Jarden Consumer Solutions, or if in Canada, Sunbeam® Corporation (Canada) Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of one year from the date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar

product of equal or greater value. This is your exclusive warranty. DO NOT attempt to repair or adjust any electrical or mechanical functions on this product.

Doing so will void this warranty. This warranty is valid for the original retail purchaser from the date of initial retail purchase

and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions of this warranty. This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than JCS or an authorized Sunbeam® service center. Further, the warranty does not cover: Acts of God, such as ﬁre, ﬂood, hurricanes and tornadoes.

What are the limits on Sunbeam’s Liability?

JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory warranty or condition. Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or ﬁtness for a particular purpose is limited in duration to the duration of the above warranty. JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise. JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar damages or loss of proﬁts, or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by any other party.

Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you speciﬁc legal rights, and you may also have other rights that vary from province to province, state to state or jurisdiction to jurisdiction.

In the U.S.A., this warranty is oﬀered by Sunbeam® Products, Inc. doing business as Jarden Consumer Solutions located in Boca Raton, Florida 33431.

In Canada, this warranty is oﬀered by Sunbeam® Corporation (Canada) Limited, doing business as Jarden Consumer Solutions located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1.

PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF

THESE ADDRESSES OR TO THE PLACE OF PURCHASE.

IMPORTANT SAFEGUARDS

• This device sh ould only be used whe n training dogs fo r deterring

unwanted behaviors.

• This device is n ot a toy; keep out of reach o f children.

• This device is n ot intended to provi de protection a gainst aggressi ve dogs.

• This basic rem ote trainer should o nly be used on one dog a t a time.

• Your dog should be in g ood health when usi ng this product .

• This produc t is not to be used on do gs less than 9 lbs.

• This produc t is not to be used on do gs less than 6 months o ld.

• Your dog should not b e left unatte nded with this colla r on. Avoid leaving

the collar on t he dog for more than 8 co ntinuous hours p er day. Prolonged

collar use c an cause pressur e sores which may lead t o skin irritatio n

such as cont act dermatiti s or decubitus ulc ers. If a rash is disco vered

disconti nue use until the ski n area heals complete ly. If condition pers ists

for more th an 48 hours, conta ct your veterina rian.

• Do not atta ch a leash to the Sunbeam® Re chargeable Remot e Train er.

A separate c ollar or harness may be u sed provided it d oes not interfe re

with the remote trainer.

SAVE THESE INSTRUCTIONS

• This produc t should be used w hen training dogs to d eter unwanted

behaviors.

• This produ ct can be used in doors and outdoo rs.

• Adjustab le collar ts neck si zes up to 28”.

• 3 levels of cor rection can be a djusted for your d og

• Low batte ry indicator

• Waterproo f

• Rechargeable battery

DO NOT USE THIS REMOTE TRAINER UNTIL YOU

HAVE READ THESE INSTRUCTIONS

PRODUCT OVERVIEW:

INDICATOR LIGHTS:

• Low • Med • High

Solid Green:

Correction level selected

and functioning properly

Flashing Green:

Correction

administered

and received

All 3 Flashi ng Red:

Low batter y

MAIN CONTROL

BUTTON:

• On/O

• Correct ion

level adjustment

• System reset

QUICK RELEASE

FABRIC

COLLAR

Collar

ADJUSTABLE

STAINLESS STEEL

PROBES:

Correction

administering system

CHARGING JACK

WRIST LANYARD:

To prevent the remote

CHARGING JACK

Remote Control

• Correc tion button • On/O • Warning tone but ton

INDICATOR LIGHTS:

POWER

Solid Green:

Remote is on

Flashing Red:

Low batter y

INDICATOR

LIGHTS:

TRANSMIT

Flashing Green:

The warning or

correction has

been transmitted

eﬀectively

Flashing Red:

Over Correc tion

Mode

CHARGING ADAPTER:

• 2 ft. power cord

• Dual chargin g capabilities

date: 9.18.12

job# 50-0512-571p

client: Sunbeam Pet

project: 400yard trainer IM

notes:

black

571P_sun_RemoteTrainerCollar_IB-MECH.indd 1 9/18/12 4:18 PM

CAN ICES-3 (B)/NMB-3(B)

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference

to other users, the antenna type and its gain should be so chosen that the equivalent isotropicallyradiated

power (e.i.r.p.) is not more than that necessary for successful communication.

Do not transmit for more than 60% of the total transmitting use time; transmitting over 60% of the total use time may exceed the limits: Exemption from Routine Evaluation Limits-SAR Evaluation requirements. So nominal transmitting operation is 10% and 90% stand-by time.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Radiation Exposure Statement

Page 2

date: 9.18.12

job# 50-0512-571p

client: Sunbeam Pet

project: 400yard trainer IM

notes:

black

Page 3

HOW IT WOR KS:

The Sunbeam® Re chargeable Remo te Trainer should be used a s a training

aid for you an d your pet. This spec ially designed sy stem will shut oﬀ if

there is an exc ess of correct ions, for example, i f something is lean ing on

the corre ction butto n or if there is continu ous pressing. Thi s is called Over Correc tion Mode and will c ause the unit to tur n oﬀ and automaticall y reset.

IMPORTANT: The Sunbeam® Rechargeable Remote Trainer has a r ange of up to 400 y ards. For the b est result s at long range s, hold the remo te above your head and p oint to the rece iver. Other fac tors that may aﬀ ect range include weather, terrain and other radio frequencies transmitted in the area. (  g . 1

)

OPERATING INSTRUCTIONS

CHARG E THE RECE IVER COL LAR

IMPORTANT: This ste p is to be complet ed when the co llar is NOT on you r dog.

• Locate the charging jack on the Receiver

Collar and lift the rubber cover. ( g. 2)

• Insert one of the charger connectors into

the charging jack. ( g. 3)

• Plug the charger into a standard wall outlet.

• While the collar battery is charging:

- If the Receiver Collar is turned oﬀ , the

center LED light will ﬂ ash red and green

indicating the battery is charging. The

center LED light will ﬂ ash green indicating when it is fully charged. If the LED is ﬂ ashing red

discontinue charging the unit. Review the instructions to ensure that you are properly charging the receiver collar battery.

- If the receiver collar is turned on, there will be no indication that the

battery is charging or is fully charged. When the battery is low, all 3 LED lights will ﬂ ash red to remind you to charge the Receiver Collar battery.

• Charge the Receiver Collar for 24 hours for the  rst charge. Recharge

the Receiver Collar for 12 hours. When charging is complete, remove the

charging connector and replace the rubber cover.

CHARG E THE REMOTE CONTROL

• Locate the charging jack on the Remote

Control and lift the rubber cover. (

 g. 4)

• Insert one of the charger connectors into the charging jack. (

 g. 5)

• Plug the charger into a standard wall outlet.

• While the Remote Control battery is charging:

- If the Remote Control is turned o , the LED

lights will ﬂ ash red and green indicating the battery is charging. The LED lights will ﬂ ash

green indicating when it is fully charged. If

the LED is ﬂ ashing red discontinue charging

the Remote Control. Review the instructions to ensure that you are properly charging the Remote Control battery.

- If the remote Control is turned on, there will be no indication that the

battery is charging or is fully charged. When the battery is low, the Power LED light will ﬂ ash red to remind you to charge the Remote Control battery.

• Charge the Remote Control for 24 hours for the  rst charge. Recharge the Receiver Collar for 12 hours. When charging is complete, remove the

charging connector and replace the rubber cover.

COLLAR FITTING

Proper  t of the Sunbeam® Rechargea ble Remote Trainer is essential to

establish a good training foundation and optimal performance.

Note: Collar should be in the OFF position before proceeding with ﬁ tting the collar on your dog.

STEP 1:

Ensure dog is in a relaxed position.

STEP 2: With the collar clasp open loosen the adjustment buckle such that it can reach completely around your dog’s neck. (

 g. 6)

Place the main unit directly over the dog’s

voicebox. When buckled, the collar should rest

directly behind the dog’s ears (the highest part of

the neck). (

 g. 7)

Note: Make sure both stainless steel probes go through the coat completely and make contact with the skin.

Use the longer stainless steel probes if the coat does not allow the shorter probes

to reach the skin.

Before changing the stainless steel probes you must completely discharge the collar by holding a plastic handle screwdriver across both stainless steel

probes for 5 seconds. Make sure the metal portion of the screwdriver is

touching both stainless steel probes and the unit is in the OFF position.

Trimming the hair around the dog’s neck where the stainless steel probes will touch the skin is

optional, DO NOT trim the hair so short that the

skin is completely exposed as this might allow

for an irritation or rash to occur. Use a wrench when assembling or disassembling

the stainless steel probes, do not over tighten. (

 g. 8)

STEP 3: Close and lock clasp.

( g. 9)

STEP 4: Adjust for proper  t by pulling on strap

until you can ﬁ t two ﬁ ngers in between your

dog’s neck and the collar. (

 g. 10)

Note: Verify that the main body of the collar unit is directly over the dog’s voicebox. The collar should be  rm but not excessively tight.

STEP 5: Let your dog wear the product for

suﬃ cient time conﬁ rming that they are moving around normally. This step is to ensure that under daily activity the collar will remain secure and not become loose.

STEP 6: Reattach collar to your dog. Check the

ﬁ t of the collar several

times per day. Wipe the

stainless steel probes weekly with a damp cloth while collar is in o position. Reminder: If you choose to use a 2nd collar, leash or harness system make

sure it does not interfere with the operation of the Sunbeam® Rechargeable

Remote Trainer.

READY TO USE

Note: COLLAR FITTING step must be completed before you are ready to use.

STEP 1: Holding the main body of the Sunbeam® Recharge able Remote

Trainer in both hands PRESS and HOLD the Main Control Button for 4 seconds.

Note: You will hear 2 audible beeps and 3 LEDs ﬂ ash GREEN indicating the device is on.

The default correction level is LOW; this setting will illuminate GREEN for 10 seconds and then turn o . During the ten seconds, you may toggle to

diﬀ erent correction levels by pressing the Main Control Button. STEP 2:

Set correction level by pressing and holding (approximately 2 seconds)

the Main Control Button until a GREEN LED illuminates at the desired setting.

When a GREEN LED is illuminated press the Main Control Button once to toggle

to the next correction level. Once a

correction level is chosen all 3 GREEN

LEDs will illuminate every 10 seconds

to advise the unit is on. IMPORTANT:

Always make sure to turn o the collar

when not in use to conserve battery life.

Note: It is recommended to start on the LOW setting and monitor your dog’s behavior before determining if a higher

correction level is needed. The Sunbeam® Rechargea ble Remote Trainer retains the last correction level setting and will resume this mode when the unit is turned on.

STEP 3: Attach collar to your dog as you did in the COLLAR FITTING stage. STEP 4: Turn on the remote control by pressing the On/O button for 2 seconds. STEP 5: To begin using the remote trainer, ﬁ nd your dog’s recognition level

starting with the warning button. Once an unwanted behavior takes place, such as chewing, digging, barking, jumping, biting or whining, immediately press the

warning button. Each dog will react diﬀ erently and reactions may include a dip of

the head, shaking the head, whining, excessive barking or confusion. Some dogs

will respond to the warning button and stop the unwanted behavior. If this is the

case, continue training your dog using the warning button and skip to STEP 7.

associate the warning tone with the correction. Once your dog has made this association, continue use of the remote trainer utilizing the warning button only.

SPECIAL OPERATING NOTES

REMOTE CONTROL: For precaution, the collar will be ready to use 10 seconds after the user has selected or made adjustments to the correction level on the collar. The collar will not react to the handheld remote when the user turns the

collar on and/or toggles the correction settings during this period.

WARNING BUTTON: If the user presses the warning button on the remote control, the transmit GREEN LED on the remote will ﬂ ash. There will be an audible beep at the collar unit.

CORRECTION BUTTON: If the user presses the correction button on the remote control, the transmit GREEN LED on the remote will ﬂ ash. If the collar can receive the signal from the remote control, the collar’s GREEN LED of the selected correction level will light up during the correction period.

OVER CORRECTION MODE: If too many corrections occur within a 60

second period, the remote control will be deactivated for two minutes. This is to protect the dog in case something may be accidentally activating the correction button. The transmit RED LED on the remote control will be

ﬂ ashing during the entire two minute period. The unit will resume normal

operation after this two minute period.

LOW BATTERY MODE: On the collar all 3 LEDs will ﬂ ash RED for 5 seconds when the battery needs to be charged. On the remote control the power LED will ﬂ ash RED and automatically turn o .

TRAINING GUIDE

Proper training is essential to achieving the best results from the Sunbeam®

Recharge able Remote Trainer. For best results, prior to use of the remote

Each dog can have a diﬀ erent reaction to the correction it receives from the

remote trainer. Reactions can vary from a dip of the head, to shaking the head, whining, excessive barking, confusion or running away. In the event of an extreme reaction or aggression, wait until your dog is calm before

approaching your dog.

The remote trainer should be used when you want to deter unwanted

behavior. Do not leave the remote trainer collar on your dog when you are

not present. Consistently using the remote trainer at the right time will give you the best results. The more disciplined you are when using the remote trainer the better your dog will understand that unwanted behaviors are not acceptable.

It is important for the training process to be interactive. Once your dog has received a correction and stopped the unwanted behavior you should reward your dog with a treat or praise.

HINTS AND TIPS

Is this product right for me and my dog?

• The Sunbeam® Rechargeable Remote Trainer is best used in conjunction

with behavior training from a qualiﬁ ed behaviorist or obedience trainer.

• Before using the remote trainer on an aggressive or phobic dog, consult a

qualiﬁ ed behaviorist or obedience trainer.

• If your dog begins to display aggressive behavior during or after using the Sunbeam® Recharg eable Remote Trainer, discontinue use immediately and

consult a qualiﬁ ed obedience trainer or behaviorist.

• All training methods require time, commitment and consistency to achieve

optimum results.

 gure 6

 gure 4

 gure 7

 gure 5

 gure 8

 gure 9

 gure 10

 gure 2

 gure 3

 gure 1

Page 4

The Sunbeam® Re chargeable Remo te Trainer should be used a s a training

aid for you an d your pet. This spec ially designed sy stem will shut oﬀ if

there is an exc ess of correct ions, for example, i f something is lean ing on

the corre ction butto n or if there is continu ous pressing. Thi s is called Over Correc tion Mode and will c ause the unit to tur n oﬀ and automaticall y reset.

)

OPERATING INSTRUCTIONS

CHARG E THE RECE IVER COL LAR

IMPORTANT: This ste p is to be complet ed when the co llar is NOT on you r dog.

• Locate the charging jack on the Receiver

Collar and lift the rubber cover. ( g. 2)

• Insert one of the charger connectors into the charging jack. ( g. 3)

• Plug the charger into a standard wall outlet.

• While the collar battery is charging:

- If the Receiver Collar is turned oﬀ , the

center LED light will ﬂ ash red and green

indicating the battery is charging. The

center LED light will ﬂ ash green indicating when it is fully charged. If the LED is ﬂ ashing red

discontinue charging the unit. Review the instructions to ensure that you are properly charging the receiver collar battery.

- If the receiver collar is turned on, there will be no indication that the

battery is charging or is fully charged. When the battery is low, all 3 LED lights will ﬂ ash red to remind you to charge the Receiver Collar battery.

• Charge the Receiver Collar for 24 hours for the  rst charge. Recharge the Receiver Collar for 12 hours. When charging is complete, remove the

charging connector and replace the rubber cover.

REMOTE CONTROL