As with all electrical products, misuse of product or failure to properly follow the
instructions may cause overheating, fire or personal injury. Please read the product
label and all of the instructions before using your heated product.
1. Do not use this heated product with an infant, a child, an incapacitated or
immobile person, a paraplegic, a quadriplegic, a diabetic, one insensitive to
heat such as a person with poor blood circulation, or anyone who cannot clearly
understand the instructions and/or operate the controls.
2. Do not route electrical cords between the mattress and box spring. Do not allow
the cords to be pinched.
3. Do not use with damaged cords. Damaged cords can lead to fire. Do not tuck in,
trap, fold, cross or pinch cords or controls between bed slats, mattress or springs,
or against walls, footboards or bed frame.
4. Do not dry clean this heated product. Cleaning liquid may damage the insulation
of the heating element. Improper laundering may cause problems with the
heating wire which can lead to fire.
5. Do not tuck in, pinch, flex or expose the heating wire to rubbing. A damaged
heating wire may result in possible overheating or fire. Do not tuck or wrap the
heated product, supply cord or control in a sofa or other furniture. All portions
of the heated product and controller should be visible at all times.
6. Turn off or unplug the control for the heated product when not using.
7. Wrapping the cord around the controller may damage the cord. Loop loosely when
storing.
8 Controller is not waterproof. Do not immerse in water.
9. Keep the control away from drafty areas that may become damp or wet such
as an open window.
10. Do not use pins; they may damage the electric wiring.
11. Be sure this blanket/mattress pad/throw is used only on an AC supply current
circuit of 110-120 volts. Do not use with an extension cord.
2
For questions or support, please visit www.sunbeambedding.com.
12.
The product
may experience increased heat in areas where heated product is
bunched or folded while in use.
13. Keep all dogs, cats and other pets away from this heated product. This is an
electrical appliance that they can damage or be injured by.
14. Do not use blanket/mattress pad on a waterbed, sofa, bunk bed or mechanically
adjustable bed and do not use throw on a waterbed, bunk bed or mechanically
adjustable bed.
15. For throw blankets: Do not use with rocking chairs, recliners, chairs with casters
or wheels, or other furniture subject to movement. Do not wrap product around
control.
16. Do not use another electronic heating device in conjunction with your heated
product.
17. Use the proper size blanket/mattress pad for your bed. For example, use
a Twin Size warming blanket on a Twin Size bed.
18. If the following Important Instructions are not followed, the heated product will
not operate properly.
19. Not for hotel, motel or other institutional use.
20. If you see the heated product operating improperly, unplug it immediately and
call Sunbeam Consumer Care in the U.S at 800-892-7684 or in Canada at
800-667-8623.
21. Do not tuck in wired area of blanket or throw.
22. Do not use with generator power.
POLARIZED PLUG:
Plug power cord into a 110-120 volt wall outlet. Do not attempt
to force the plug. This appliance has a polarized plug (one blade
is wider than the other). To reduce the risk of electrical shock,
this plug is intended to fit only one way into an outlet. If the plug
does not fit in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety feature.
For questions or support, please visit www.sunbeambedding.com.
IMPORTANT
3
QUICK SET-UP GUIDE
1
3
2
4
Mattress Pad & Blanket
TWIN/FULL
SINGLE CONTROL SET-UP
STEP 1
Place on bed with
label at foot of bed
facing out
Left Side
STEP
Plug Power Cord
4
into wall
Right Side
Power Cord
Control
STEP
Connect the Control
2
Cord connector and
module securely
Control Cord
Connector
Module
Label
Flag Tag
BASE UNIT FOR
REMOTE CONTROL
SET-UP
Module
Run Base Unit Cord under the bed
QUEEN/KING/CALIFORNIA KING
DUAL CONTROL SET-UP
STEP 1
STEP
Place on bed with
label at foot of bed
facing out
Connect the Control
2
Cord connector and
module securely
Control Cord
Connector
Left (Secondary)
Module
Control
Left Side
Label
STEP
STEP
Right Side
Run Control Cord
3
under the bed
Plug Power Cord
4
into wall
Power Cord
Right
(Primary) Control
(Label on back
of control)
Flag Tag
STEP
Run Control Cord
3
under the bed
4
For questions or support, please visit www.sunbeambedding.com.
Control Cord
Connector
QUICK SET-UP GUIDE
Heated Throw
STEP 1
STEP
Connect the Control
Cord connector and
module securely
Plug Power Cord
2
into wall
Flag Tag
Power
Cord
Throw Cord
Connector
Module
Control
Label
Throw Cord
Flag Tag
Power
Cord
Throw Cord
Connector
Module
Control Cord
Control
Label
Throw Cord
Connector
PLEASE follow these directions in the order they are given to
ensure your product will work correctly. Do not turn on the
product until it has been fully assembled.
CAUTION:
• Always make sure cords and controls are NOT trapped or
• Do not plug main power cord into the wall
pinched between bed slats, mattress, springs, against wall,
foot board or bed frame, or between furniture, walls or chairs.
IMPORTANT
outlet until you have completely set up your
heated product per the instructions.
For questions or support, please visit www.sunbeambedding.com.
How to Obtain Warranty Service ............................................................................... 16
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
If you have any questions while setting up or using your product,
please visit us on the World Wide Web at: www.sunbeambedding.com
or contact Sunbeam Consumer Care in the U.S. at (800) 892-7684
or in Canada at (800) 667-8623.
IMPORTANT
is intended to fit only one way into an outlet. If the plug does not fit in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
6
CAUTION: Do not plug main power cord into the wall outlet until you have
completely set up your heated product per the instructions.
• Disconnect power cord from wall before detaching control from heated product.
• Always make sure cords and controls are NOT trapped or pinched between bed slats,
mattress, springs, against wall, foot board or bed frame, or between furniture, walls or chairs.
CAUTION: Do not attempt to force the plug. This appliance has a polarized plug
(one blade is wider than the other). To reduce the risk of electrical shock, this plug
For questions or support, please visit www.sunbeambedding.com.
Heated Blanket, Mattress Pad and
Comforter Setup
1 Place the heated blanket/mattress pad on the bed with the label at the foot of the bed facing upward.
2 Connect the cord into the module at the bottom of the heated blanket/ mattress pad until the plastic
hinges click into place.
CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection.
3 Run the control cord on the floor under the bed. Do not sandwich cord between the mattress and box
spring. Avoid any tangling or pinching.
4 Plug power cord into a 110-120 volt wall outlet.
CAUTION: Do not use with generator power.
Control Placement:
• Dual Control for heated blanket or mattress pad – place primary control (label on back of
control) on the right side of the bed.
STEP 1
STEP
Place on bed with
label at foot of bed
facing out
Connect the Control
2
Cord connector and
module securely
Control Cord
Connector
Left (Secondary)
Module
STEP
Control
Left Side
Right Side
Label
Plug Power Cord
4
into wall
Power Cord
Right
(Primary) Control
(Label on back
of control)
Flag Tag
3
STEP
• Single Control for heated blanket or mattress pad –
the control can be placed on either side of the bed.
STEP
STEP
Place on bed with
1
label at foot of bed
facing out
Connect the Control
2
Cord connector and
module securely
Control Cord
Connector
See Control Features on page 8
for your individual control.
Left Side
Module
Label
Flag Tag
If there is a flashing light or your control displays
a flashing “F” ,“FF”, “F1” or “F2” see page 8.
For questions or support, please visit www.sunbeambedding.com.
Run Control Cord
under the bed
4
STEP
Right Side
Run Control Cord
3
STEP
under the bed
Plug Power Cord
into wall
Power Cord
Control
7
Control Chart
™
SimpliTouch
SimpliTouch™ Pro
Style #
(Single
Control)
Style #
(Dual
Control)
Backlit
Display
LED Display
Ambient
Temperature
Compensation
Auto-Off
Warming
Settings
Preheat
Easy Grip
K85PS85/S85A U85085P8585PW85X85
K85KQP
* S85KQA only
If your controller does not appear on the chart, please visit our website for more information.
EasySet™ Pro StyleSmart™ II ComfortSet™SelectTouch™ChoicePlus™DesignSmart™ChoiceTouchEliteStyle™PrimeStyle
S85KQ/
U85KQ085KQP85KQ85KQPW85KQX85KQ
S85KQA
bbbbb
b
bbb
10 hour*
10 hour
(S85A,
10 hour 10 hourSelect10 hour
S85KQA)*
1010101010201010333
bbbbb
bbbbbb
Selectable
A/0
2, 6 or 10
hour
Selectable
A/0
2, 6 or 10
hour
b
Programable
™
EliteStyle™ II
AO
N85AP
M85AP
Throw
T85A
Throw
Throw
3 hour 3 hour 3 hour
Control Features
(for all controllers except DesignSmart™ and ChoiceTouch, see page 9 for
detailed features.)
Auto-Off Feature:
The “Auto-Off” feature is designed for conservation of energy by automatically turning your blanket or
mattress pad off after 10 hours of continuous use (3 hours for throws).
For Dual Controls:
Each control operates independently and will turn off 10 hours after the control is turned “On”.
Auto-Off Select* Feature (selected models only):
Some models with the “Auto-Off” feature (see control chart) offer an “Auto-Off Select” button that can
disable the “Auto-Off” feature so the heated product will not automatically turn off.
Controls with the “Auto-Off Select” feature have the “Auto-Off” active as the default so the heated product
will automatically turn off after 10 hours.
To disable the “Auto-Off”, press the “Auto-Off Select” button. The word “StayOn” will appear in the digital
display to indicate the “Auto-Off” feature is deactivated and the heated product will NOT automatically turn
off after 10 hours. The heated product will remain on until the product is manually turned off by pressing the
“On/Off” button.
To activate auto-off, press the “Auto-Off Select” button. The word “AutoOff” will appear in the digital display to
indicate the “Auto-Off” feature is activated and the heated product will automatically turn off after 10 hours.
Note: After a power outage, the “Auto-Off” feature automatically resets the timer.
To restart all heated products after a power failure:
Press the power button and the heated product will begin to warm.
8
For questions or support, please visit www.sunbeambedding.com.
Preheat Feature (selected models only):
The preheat function will heat the bed for a period of 30 minutes and the control will return to its
original setting.
1 To use the preheat feature, simply turn on the warming product by pressing the “On/Off” button and
then press the “Preheat” button. The display will show “PH” while the function is activated.
2 To reset the preheat feature, simply turn off the control by pressing the “On/Off” button and then turn
it back on by pressing the “On/Off” button.
Using Your Control:
1 To turn the control on, press the “On/Off” button.
Note: For SelectTouch™, ComfortSet™, and ChoicePlus™ controls, the backlit display light will reset
itself by flashing “88” and then will return to the previous setting and will begin to warm.
2 Adjust the warming setting to your personal comfort by rotating the top knob left or right for
ChoicePlus™, SimpliTouch™, and EasySet™ controls.
3 Note: For SelectTouch™ and ComfortSet™ controls, press the large left button with the “-” sign to
lower the heat setting and the large right button with the “+” sign to increase your heat setting.
4 To turn the heated blanket/mattress pad OFF, press the “On/Off” button.
CAUTION: ALWAYS turn the heated blanket/mattress pad “OFF” when not in use.
DesignSmart™ Controller
Selectable Auto Off:
You can set the auto-off time at 2hrs, 6hrs or 10hrs.
1 To use the auto-off feature, Press the Mode button until the “Auto-Off” words begin to flash.
2 While the “auto-off” is flashing, use the + (dimmer increase) and - (dimmer decrease) buttons to
scroll through the 3 auto off options.
Auto off will be set at the highlighted time. (The control will remember the auto off setting unless AC
power is disconnected.
If no button is pressed after 6 seconds, the highlighted setting will be set.
Preheat:
The preheat function will heat the bed for a period of 30 minutes and the control will return to its
original setting.
1 Press the mode button until “Preheat” appears on the screen. The preheat will then start.
2 To turn off the Preheat feature press the mode button until the “Preheat” disappears from the screen
or press the On/Off button to power off the unit.
Heat Adjustment:
There are 10 settings from Low to Hi.
To adjust the heat setting, simply press the + (raise heat temp) or the – (lower heat temp) on the large
circular button in the center of the control.
Dimmer:
Your controller gives you the ability to adjust the brightness of the display.
To adjust the brightness, Press the + (dimmer increase) or the – (dimmer decrease) buttons to change
the brightness level.
ChoiceTouch Controller
Setting the clock:
1. Turn the unit over to find the Slide switch.
2. Slide the switch to Time Set. The clock will begin to flash.
3. Press the + (dimmer increase) or the – (dimmer decrease) buttons to scroll through the time. (if you hold
down the button, the time will scroll at a faster pace).
For questions or support, please visit www.sunbeambedding.com.
9
Note: there is a P to the right of the clock to denote PM.
4. Release the button to stop at the desired time.
5. When the desired time has been reached, slide the switch to the center position to save the time and return
to normal operation.
Note: The clock will blink until the time has been set.
The control will remember the time settings unless AC power is disconnected.
Selectable Auto Off:
You can set the auto-off time at 2hrs, 6hrs or 10hrs.
If the personalized options are not selected, the auto off feature is designed for conservation of energy by
automatically turning your blanket or mattress pad off after 10 hrs of continuous use.
To use the auto-off feature, Press the Mode button until the “Auto-Off” words begin to flash.
While the “auto-off” is flashing, use the + (dimmer increase) and - (dimmer decrease) buttons to scroll
through the 3 auto off options.
Auto off will be set at the highlighted time. (The control will remember the auto off setting unless AC power is
disconnected.
If no button is pressed after 6 seconds, the highlighted setting will be set.
Preheat:
The preheat function will heat the bed for a period of 30 minutes and the control will return to its original
setting.
Your controller allows you to set the time that you would like your blanket to start preheating each night. That
way you can always get into a cozy warm bed.
To set the preheat time with a set time
1. Make sure the clock has been set. To set the clock, please see the clock set instructions.
2. Set the time you would like the pre-heat to come on.
3. Turn the unit over to find the Slide switch. (if the clock has not been set, please see clock set instructions.)
4. Slide the switch to Preheat Time Set. The clock and “Preheat will flash”. Press the + (dimmer increase) or
the – (dimmer decrease) buttons to scroll through the time. (if you hold down the button, the time will scroll
at a faster pace).
Note: there is a P to the right of the clock to denote PM.
4. Release the button to stop at the desired time.
5. When the desired time has been reached, slide the switch to the center position to save the time and return
to normal operation.
Note: The Preheat time will blink until you have set the Clock. Please set the Clock before you set the time you
would like preheat to start.
The control will remember the time settings unless AC power is disconnected.
To use the preheat function without setting the time
1. Press the mode button until Preheat flashes on the screen.
2. Press the + (dimmer increase) or – (dimmer decrease) to scroll through the options. Each press moves
changes the options as follows:
• Preheat On with the time displayed. This will set the preheat to turn on automatically at the pre-set time
displayed. If you do not press any button for 6 seconds, the preheat time will be set and the unit will be
ready to preheat at the set time.
• Preheat On without the time displayed. This will start the preheat when you leave the mode setting. You can
leave the mode setting by not pressing any button for 6 seconds.
• Preheat off. This stops any preheat functionality.
If no button is pressed after 6 seconds, the last setting will be stored.
10
For questions or support, please visit www.sunbeambedding.com.
Loading...
+ 22 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.