Sunbeam SCK02SMWBS Owner's Manual

User’s Manual

Beer Dispenser

Model: SCK02SMWBS

PTT092106

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS 3

GROUNDING INSTRUCTIONS 5

PRODUCT DIAGRAM 6

INSTALLATION INSTRUCTIONS 7

OPERATION INSTRUCTIONS 11

BEFORE CALLING FOR SERVICE 12

IMPORTANT SAFETY INSTRUCTIONS

READ ALL SAFETY INSTRUCTIONS BEFORE USING THIS APPLIANCE

When using electrical appliances, basic safety precautions should be followed, including the following:

Read all instructions before using the beer dispenser.

1.
Plug into a grounded 3-prong outlet; do not remove grounding plug; do not use an adapter; do not

2.
use an extension cord.
Replace all panels before operating.

3.
It is recommended a separate circuit be used for this unit. Use outlets that cannot be turned on and

4.
off with a switch or pull chain.
Never clean unit parts with fl ammable fl uids. Do not store or use gasoline or other fl ammable

5.
vapors and liquids in the vicinity of this or any other appliance. Fumes can create a fi re hazard or
explosion.
Before cleaning or doing any maintenance to the unit, ensure the power is turned off and the power

6.
cord is disconnected from the power outlet.
Do not attempt to service the unit unless it is specifi cally recommended in this manual. All other

7.
servicing should be referred to a qualifi ed technician.
Use two or more people to move and install the unit. Failure to do so may result in back or other

8.
injury.
To ensure proper ventilation, the front of the unit must be completely unobstructed. Choose a well-

9.
ventilated area with temperatures between 60°F and 90°F.
Do not place this unit near heat sources.

10.
This unit must be installed with all electrical, water, and drain connections in accordance with state

11.
and local codes. A standard electrical supply properly grounded in accordance with the National
Electrical Code and local codes and ordinances is required.
Do not kink or pinch the power supply cord.

12.
The fuse or circuit breaker should be 15 amperes.

13.
It is important the unit be level in order for it to work properly. You may need to make several

14.
adjustments.
All installation must be in accordance with local plumbing code requirements.

15.
Make certain the pipes are not pinched, kinked, or damages during installation.

16.
Check for leaks after connection.

17.
Never allow children to operate, play with, or crawl inside the unit.

18.
Do not use this unit for anything other than its intended purpose.

19.
Before throwing away an old unit, remove the doors, but leave the shelves in place so that children

20.
cannot easily climb inside.

3

IMPORTANT SAFETY INSTRUCTIONS (continued)

CO2 GAS CAN BE DANGEROUS

CO2 cylinders contain high-pressure compressed gas which can be hazardous if not handled properly.
Make sure to read this section and understand the following procedures:

Always connect the CO2 cylinder to a regulator. Failure to do so may result in explosion with

1.
possible death or injury when the cylinder valve is opened.
Never connect the CO2 cylinder directly to the product container.

2.
Always follow correct procedures when cylinders are changed.

3.
Always secure the cylinder in an upright position.

4.
Never drop or throw a CO2 cylinder.

5.
Always keep CO2 cylinders away from heat. Store extra cylinders in a cool place. Securely fasten

6.
with a chain in an upright position.
Always ventilate and leave the area immediately if CO2 leakage has occurred.

7.
Always check the D.O.T. test date on the cylinder neck before installation. If over fi ve years old, do

8.
not use; return cylinder to gas supplier.
Never connect a product container unless there are two safeties in the pressure system: one at or on

9.
the CO2 regulator and one at or on the product coupler on in the pressure gas line.

INSTALLATION

Before connecting the beer dispenser, let the unit sit upright for approximately 2 hours. This will

•
reduce the possibility of a malfunction in the cooling system from handling during transportation.
Clean the interior surface with warm water and a clean cloth.

•
This appliance is designed to be free-standing only and should not be recessed or built-in.

•
Place your beer dispenser on a fl oor that is strong enough to support the unit when fully loaded.

•
Allow three inches of space between the back and sides of the beer dispenser to allow proper air

•
circulation for the compressor to cool.
Keep the beer dispenser away from direct sunlight and heat sources. Direct sunlight may affect

•
the acrylic coating and heat sources may increase electrical consumption. Extremely cold ambient
temperatures may also cause the unit to preform poorly.
Keep the unit out of moist areas.

•
Plug the unit into an exclusive, properly installed, grounded wall outlet. Do not, under any

•
circumstances, cut or remove the third prong from the power cord.
After plugging in the unit, allow it to cool down for 2-3 hours before placing any contents in the

•
compartment.

4