Sunbeam Sbm6500b, Sbm6500w Service Manual

MICROWAVE OVEN

SERVICE MANUAL

MODEL: SBM6500W/SBM6500B

CAUTION

website: http://www.lgservice.com
e-mail: http://www.lgeservice.com/techsup.html

BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : 3828W5S2164

Feb., 2002

Printed in Korea

This device is to be serviced only by properly qualified service personnel.
Consult the service manual for proper service procedures to assure continued safety operation and for precautions to be
taken to avoid possible exposure to excessive microwave energy.

PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

A) Do not operate or allow the oven to be operated with the door open.

B) Make the following safety checks on all ovens to be serviced before activating the magnetron or other

microwave source, and make repairs as necessary; (1) interlock operation, (2) proper door closing, (3)

seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and

latches, (5) evidence of dropping or abuse.

C) Before turning on microwave power for any service test or inspection within the microwave generating

compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,

integrity, and connections.

D) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation

and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual

before the oven is released to the owner.

E) A microwave leakage check to verify compliance with the Federal Performance Standard should be

performed on each oven prior to release to the owner.

SAFETY PRECAUTIONS

(Page)

SAFETY PRECAUTIONS

---------------------------------------------------------------------

Inside front cover

SPECIFICATIONS

-----------------------------------------------------------------------------------------------------

1-1

CAUTIONS

--------------------------------------------------------------------------------------------------------------

2-1

INSTALLATIONS

------------------------------------------------------------------------------------------------------

3-1

OPERATING INSTRUCTIONS

------------------------------------------------------------------------------------

4-1

FEATURES

------------------------------------------------------------------------------------------------------------------------

4-1

OPERATION CHECK

----------------------------------------------------------------------------------------------------------

4-1

OPERATING PROCEDURE

-------------------------------------------------------------------------------------------------

4-1

SCHEMATIC DIAGRAM

------------------------------------------------------------------------------------------------------

4-2

CIRCUIT DESCRIPTION

-----------------------------------------------------------------------------------------------------

4-3

SERVICE INFORMATION

------------------------------------------------------------------------------------------

5-1

TOOLS AND MEASURING INSTRUMENTS

---------------------------------------------------------------------------

5-1

MICROWAVE LEAKAGE TEST

--------------------------------------------------------------------------------------------

5-1

MEASUREMENT OF MICROWAVE POWER OUTPUT

-----------------------------------------------------------

5-3

DISASSEMBLY AND ADJUSTMENT

-------------------------------------------------------------------------------------

5-3

INTERLOCK CONTINUITY TEST

------------------------------------------------------------------------------------------

5-7

COMPONENT TEST PROCEDURE

--------------------------------------------------------------------------------------

5-8

TROUBLE SHOOTING

------------------------------------------------------------------------------------------------------

5-11

EXPLODED VIEW

-----------------------------------------------------------------------------------------------------

6-1

REPLACEMENT PARTS LIST

------------------------------------------------------------------------------------

7-1

CONTENTS

This microwave oven is designed for household use only.

It is not recommended for commercial purposes.

ITEM

MODEL

Power Requirement

Power Output

Microwave Frequency

Magnetron

Timer

Outside Dimensions

Cavity Dimensions

Net Weight

Shipping weight

Control Complement

Nameplate Location

Accessories

DESCRIPTION

SBM6500W/SBM6500B

120 Volts AC 60 Hz

900 Watts (8.0 A)

Single phase, 3-wire grounded

600 Watts full microwave power (IEC60705)

2,450 MHz

2M213

0 ~ 35 min.

17

15

/16” (W) x 113/16” (H) x 125/8” (D)

12

3

/16” (W) x 731/32” (H) x 115/8” (D)

24.7 lbs (approx.)

26.9 lbs (approx.)

Mechanical Rotary System

Full Power Cooking

Owner's manual & cooking guide

Glass turntable

Rotating ring

Back Side

1-1

SPECIFICATIONS

• DO NOT operate on a 2-wire extension cord during
repair and use.

• NEVER TOUCH any oven components or wiring during
operation.

• BEFORE TOUCHING any parts of the oven, always
remove the power plug from the outlet.

• For about 30 seconds after the oven stops, an electric
charge remains in the high voltage capacitor. When
replacing or checking, you must discharge the high
voltage capacitor by shorting across the two terminals
with an insulated screwdriver.

•

Remove your watches whenever working close to or

replacing the Magnetron.

• NEVER operate the oven with no load.

• NEVER injure the door seal and front plate of the oven
cavity.

• NEVER put iron tools on the magnetron.

• NEVER put anything into the latch hole and the
interlock switches area.

• Proper operation of the microwave oven requires that
the magnetron be assembled to the waveguide and
cavity. Never operate the magnetron unless it is
properly installed.

• Be sure that the magnetron gasket is properly
installed around the dome of the tube whenever
installing the magnetron.

2-1

CAUTIONS

Unlike other appliances, the microwave oven is
high-voltage and high-current equipment.
Though it is free from danger in ordinary use,
extreme care should be taken during repair.

THE OVEN IS TO BE SERVICED ONLY
BY PROPERLY QUALIFIED SERVICE
PERSONNEL.

MICROWAVE RADIATION

Personnel should not be exposed to the
microwave energy which may radiate from the
magnetron or other microwave generating
device if it is improperly used or connection.
All input and output microwave connections,
waveguide, flange, and gasket must be secure
never operate the device without a microwave
energy absorbing load attached.
Never look into an open waveguide or antenna
while the device is energized.

Gasket

ANTENNA

COOLING FIN

MAGNETRON
CHASSIS GROUND

FILAMENT
TERMINALS

MAGNETRON

INSTALLATIONS

3-1

INSTALLING

1. Empty the microwave oven and clean inside it with
a soft, damp cloth. Check for damage such as
misaligned door, damage around the door or dents
inside the cavity or on the exterior.

2. Put the oven on a counter, table, or shelf that is
strong enough to hold the oven and the food and
utensils you put in it. (The control panel side of the
oven is the heavy side. Use care when handling.)

3. Do not block the vent and the air intake openings.
Blocking vent or air intake openings can cause
damage to the oven and poor cooking results.
Make sure the microwave oven legs are in place to
ensure proper air flow.

4. The oven should not be installed in any area where
heat and steam are generated, because they may
damage the electronic or mechanical parts of the
unit.
Do not install the oven next to a conventional
surface unit or above a conventional wall oven.

5. Use microwave oven in an ambient temperature
less than 104°F (40°C).

6. Place the microwave oven on a sturdy and flat
surface at least 10 cm (4 inches) from the wall.

7. Place the microwave oven as far away as possible
from TV, RADIO, COMPUTER, etc., to prevent
interference.

GROUNDING INSTRUCTIONS

For personal safety, this appliance must be fully
grounded at all times.

In the event of an electrical short circuit, grounding
reduces the risk of electrical shock.
The plug must be plugged into an outlet that is
properly installed and grounded.

BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.

WARNING

Improper use of the grounding plug can result in a
risk of electric shock.
Do not, under any circumstances, cut or remove
the third ground prong from the power cord plug.

PREFERRED METHOD

ENSURE PROPER GROUND

EXISTS BEFORE USE

TEMPORARY METHOD
(ADAPTER PLUGS NOT
PERMITTED IN CANADA)

ALIGN LARGE
PRONGS/SLOTS

10cm

ENSURE PROPER GROUND
AND FIRM CONNECTION
BEFORE USE

4-1

OPERATING INSTRUCTIONS

FEATURES

Oven Front Plate

Window Door Screen

Door Seal

Power Knob

Timer Knob

Safety Door Lock System

Turntable

Rotating Ring

WARMWARM

LOWLOW

MEDIUMMEDIUM

HIGHHIGH

The microwave oven is designed to be simple and
easy to operate. Please follow these instructions
carefully.

1. Place the food in a suitable cooking utensil. Open
the microwave oven door and place the utensil in
the center of the oven on the glass tray.

2. Close the oven door.

3. Turn the TIMER KNOB clockwise to set the
cooking time.

4. When the TIMER reaches OFF, the signal sounds
and the oven will automatically shut off.

5. Open the door and remove the food from the
oven.

6. To stop cooking before the timer reaches OFF,
either open the door or simply turn the timer to
OFF.

NOTE :

1. The oven starts as soon as the KNOB is turned.
We recommend turning the KNOB past the time
you want and then turn back to the desired setting.

2. The door can be opened during the cooking
process by pushing the Door Open Button. The
timer will stop and the microwave activity will
cease. When the door is closed, cooking will
resume until the full cooking time has elapsed.
After cooking is finished, the Timer will be at OFF.

After unpacking this appliance, examine the new
oven for evidence of shipping damage. This is most
important since a damaged oven may allow the
escape of microwave energy. Make sure you remove
all packing from the microwave cavity.
Check the oven operation when unpacking the unit
and any time the oven is not working properly.

1. Plug the power cord into an earthed electrical
socket.

2. Place the glass tray inside the oven cavity.

3. Place a cup of water (at room temperature) inside
the oven, on the glass tray.

4. Close the door securely.

5. Set the Timer for 3 to 4 minutes (note : microwave
activity starts).

6. When the cooking time has elapsed, the signal will
sound (note: all microwave activity stops).

7. If the oven is operating normally, the water will be
hot.

OPERATION CHECK

OPERATING PROCEDURE

SCHEMATIC DIAGRAM

4-2

IMPORTANT SAFETY NOTE: THE SHADED AREAS ON THIS SCHEMATIC DIAGRAM INCORPORATE SPECIAL FEATURES

IMPORTANT FOR PROTECTION FROM MICROWAVE RADIATION, FIRE, ELECTRICAL SHOCK, AND

HAZARDS. WHEN SERVICING IT IS ESSENTIAL THAT ONLY MANUFACTURER’S SPECIFIED PARTS

BE USED FOR THE CRITICAL COMPONENTS IN THE SHADED AREAS OF THE SCHEMATIC DIAGRAM.

NOTICE: SINCE THIS IS BASIC SCHEMATIC DIAGRAM, THE VALUES OF COMPONENTS AND

SOME PARTIAL CONNECTIONS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.

CIRCUIT DESCRIPTION

GENERAL DETAILS

• When the door is closed, the primary switch is ON, the
secondary switch is ON, and the monitor switch opens
(contact COM and NO).

• The latches are secured by the latch board, the oven
light turns on while the oven is operation.

WHEN THE TIMER KNOB IS ROTATED

• When the timer knob is rotated, the contacts of timer
switch close.

• The contact of the secondary switch close the circuit.

• Power input is supplied to the high voltage transformer
through the fuse to the primary timer and secondary
switches.

• Turntable rotates

• The fan motor rotates and cools the magnetron by
blowing air (coming from the intake on the baseplate).

• The air is also directed into the oven to exhaust the
vapor in the oven through the upper plate.

• Cooking time starts counting down.

• 3.2 volts AC is generated from the filament winding of
the high voltage transformer. This 3.2 volts is applied to
the magnetron to heat the magnetron filament through
two noise-preventing choke coils.

• A high voltage of approximately 2100 volts AC is
generated in the secondary of the high voltage
transformer which is increased by the action of the high
voltage diode and charging of the high voltage
capacitor.

• The negative 4,000 Volts DC is applied to the filament
of the magnetron.

WHEN THE DOOR IS OPENED DURING
COOKING

• Both the primary and timer switches are cut off primary
winding voltage of the high voltage transformer.

• When the door is opened, the secondary switch is
opened and when the door is closed, the secondary
switch is closed.

• The timer, turntable and fan motor stop.

• As the door is opened, if the contact of primary switch
fail to open, the fuse opens due to the large current
surge caused by the monitor switch activation, which,
in turn, stops magnetron oscillation.

4-3

FUSE

P/S

P/S : Primary Switch
T/S : Tiemr Switch
S/S : Secondary Switch

T/S S/S

H.V.

TRANS-

FORMER

FUSE

P/S

T/S S/S

M/S

P/S : Primary Switch
T/S : Tiemr Switch
M/S : Monitor Switch
S/S : Secondary Switch

H.V.

TRANS-

FORMER

CAUTIONS

• Be sure to check microwave leakage prior to
servicing the oven if the oven is operative prior to
servicing.

• The service personnel should inform the
manufacturer, importer, or assembler of any
certified oven unit found to have a microwave
emission level in excess of 5 mW/cm2and should

repair any unit found to have excessive emission levels
at no cost to the owner and should ascertain the cause
of the excessive leakage. The service personnel
should instruct the owner not to use the unit until the
oven has been brought into compliance.

• If the oven operates with the door open, the service
personnel should:

- Tell the user not to operate the oven.

- Contact the manufacturer and CDRH
(Center for Devices and Radiological Health)
immediately.

NOTE: Address on CDRH

Office of Compliance(HFZ-312)
Center for Devices and Radiological
Healthe 1390, Piccard Drive,
Rockville. MD 20850

• The service personnel should check all surface and
vent openings for microwave leakage.

• Check for microwave leakage after every servicing.
The power density of the microwave radiation leakage
emitted by the microwave oven should not exceed
4 mW/cm2. Always start measuring of an unknown field
to assure safety for operating personnel from radiation
leakage.

MEASURING MICROWAVE ENERGY
LEAKAGE

• Pour 275±15cc of 20±5°C (68±9°F) water in a beaker
which is graduated to 600 cc, and place the beaker
on the center of the turntable.

• Set the energy leakage monitor to 2,450 MHz and
use it following the manufacturer's recommended
test procedure to assure correct result.

• When measuring the leakage, always use the 2­inch (5 cm) spacer supplied with the probe.

• Operate the oven at its maximum output.

• Measure the microwave radiation using and
electromagnetic radiation monitor by holding the
probe perpendicular to the surface being measured

Move probe along shaded area

Probe scanning speed
Less than 2.5 cm/sec
(1 in/sec)

5-1

SERVICE INFORMATION

TOOLS AND MEASURING INSTRUMENTS

MICROWAVE LEAKAGE TEST

NECESSARY TOOLS

Tools normally used for TV servicing are sufficient.
Standard tools are listed below.

• Diagonal pliers

• Long nose pliers

• Phillips screwdriver

• Flat blade screwdriver

• Wrench (size 5mm)

• Nutdriver (size 5mm)

• Adjustable wrench

• Soldering iron

• Solder

• Vinyl insulation tape

• Polishing cloth

NECESSARY MEASURING INSTRUMENTS

• TESTER (VOLTS-DC, AC, Ohmmeter)

• Microwave survey meter

- Holaday HI-1500
HI-1501

- Narda 8100

8200

• Inch scale

• 600 cc non conductive material beaker (glass or plastic),
inside diameter: approx. 8.5 cm (3

1

/2

in.)

• Cylindrical and made of borosilicate glass vessel.
max. thickness: 3 mm
outside diameter: approx. 190mm
height: approx. 90mm

• Glass thermometer: 100°C or 212°F (1 deg scale)

MEASUREMENT WITH OUTER CASE
REMOVED

• When you replace the magnetron, measure for
microwave energy leakage before the outer case is
installed and after all necessary components are
replaced or adjusted.

Special care should be taken in measuring the

following parts. (Circled area of Fig. below)

- Around the magnetron

- The waveguide

MEASUREMENT WITH A FULLY
ASSEMBLED OVEN

• After all components, including the outer case, are fully
assembled, measure for microwave energy leakage
around the door viewing window, the exhaust opening,
and air inlet openings.

• Microwave energy leakage must not exceed the values
prescribed below.

NOTE: Leakage with the outer case removedless than

5 mW/cm.sq. Leakage for a fully assembled
oven (Before the latch switch (primary) is
interrupted) with the door in a slightly opened
position-less than 2 mW/cm.sq.

NOTES WHEN MEASURING

• Do not exceed meter full scale deflection.

• The test probe must be removed no faster than
1 inch/sec (2.5 cm/sec) along the shaded area,
otherwise a false reading may result.

• The test probe must be held with the grip portion of the
handle.

A false reading may result if the operator's hand is

between the handle and the probe.

• When testing near a corner of the door, keep the probe
perpendicular to the surface making sure the probe
horizontally along the oven surface; this may cause
probe damage.

RECORD KEEPING AND NOTIFICATION
AFTER MEASUREMENT

• After adjustment and repair of any microwave energy
interruption or microwave energy blocking device,
record the measured values for future reference. Also
enter the information on the service invoice.

• The microwave energy leakage should not be more
than 4 mW/cm.sq. after determining that all parts are in
good condition, functioning properly and genuine
replacement parts which are listed in this manual have
been used.

• At least once a year, have the electromagnetic energy
leakage monitor checked for calibration by its
manufacturer.

5-2

WARNING : AVOID CONTACTING ANY

HIGH VOLTAGE PARTS

SPECIAL TIP

• This oven used the button head screws.

• When you remove the screws, use the
tamper-resistant Torx driver having a
pin-in-head.

Button Head

(Torx style 2)

• Microwave power output measurement is made with
the microwave oven supplied at its rated voltage and
operated at its maximum microwave power setting with
a load of (1000±5) g of potable water.

• The water is contained in a cylindrical borosilicate glass
vessel having a maximum material thickness of 3 mm
and an outside diameter of approximately 190mm.

• The oven and the empty vessel are at ambient
temperature prior to the start of the test.

• The initial temperature (T1) of the water is (10±2)°C It
is measured immediately before the water is added to
the vessel. After addition of the water to the vessel,
the load is immediately placed on the center of the
turntable which is in the lowest position and the
microwave power switched on.

• The time T for the temperature of the water to rise by a
value ∆ T of (10±2)° is measured, where T is the time

in seconds and ∆T is the temperature rise. The initial
and final water temperatures are selected so that the
maximum difference between the final water
temperature and the ambient temperature is 5°.

• The microwave power output P in watts is calculated
from the following formula :

4187 x (∆T)

T

is measured while the microwave generator is
operating at full power. Magnetron filament heat-up
time is not included. (about 3 sec)

• The water is stirred to equalize temperature throughout
the vessel, prior to measuring the final water
temperature.

• Stirring devices and measuring instruments are
selected in order to minimize addition or removal of
heat.

A. OUTER CASE REMOVAL

1) Disconnect the power supply cord from the outlet.

2) Remove the screws from the rear of the case.
The outer case must be moved backward to be lifted
off.

B. POWER SUPPLY CORD

1) Remove the outer case.

2) Disconnect two terminals and remove one screw of
the ground terminal.

C. CONTROL PANEL ASSEMBLY

1) Open the door.

2) Remove the screws for securing the control panel.

3) Disconnect the leadwire from motor timer.

4) Lift up and pull out control panel assembly carefully

from the cavity.

CAUTION: DISCHARGE THE HIGH VOLTAGE

CAPACITOR BEFORE SERVICING

(Refer to page 2-1)

5-3

WATER LOAD

TURNTABLE

c

MEASUREMENT OF MICROWAVE POWER OUTPUT

P =

Remove the screw

Lift up and pull out control panel

DISASSEMBLY AND ADJUSTMENT

securing s

5-4

D. TIMER MOTOR REMOVAL

1) Remove the control panel assembly from the
cavity. (Refer to control panel assembly removal
on previous page.)

2) Remove screws which hold the timer motor to the
control panel.

3) Removed the timer knob.

4) Remove the door open button.

E. DOOR GROSS ASSEMBLY REMOVAL

1) Open the door.

2) Remove the choke cover very carefully with a
flat-blade screwdriver.

CAUTION : Be careful not to damage door seal plate

by screwdriver.

3) Lift up and push the door.

NOTE:

1. After replacing the door, be sure to check that the

primary switch, monitor switch, and secondary switch
operate normally.

2. After replacing the door, check for microwave energy

leakage with a survey meter. Microwave energy must
be below the limit of 5 mW/cm. (with a 275 ml water
load)

3. When mounting the door assembly to the oven

assembly, be sure to adjust the door assembly parallel
to the chassis. Also, adjust so the door has no play
between the inner door surface and oven frame
assembly. If the door assembly is not mounted
properly, microwaves may leak from the clearance
between the door and the oven.

Remove choke cover

Remove door

Control Panel

Powr Knob

Timer Knob

Motor

5-5

F. HIGH VOLTAGE TRANSFORMER

REMOVAL

1) Discharge the high voltage capacitor.

2) Disconnect the leadwire from magnetron, high voltage
transformer, and capacitor.

3) Remove the screw holding the high voltage
transformer to the baseplate.

G. FAN MOTOR ASSEMBLY REMOVAL

1) Discharge the high voltage capacitor.

2) Disconnect the leadwire from fan motor, and high
voltage capacitor.

3) Remove the two screws holding the the suction guide
assembly to the oven cavity and remove the high
voltage diode earth screw.

4) Remove the two screws holding the fan motor
assembly to the suction guide assembly.

H. HIGH VOLTAGE CAPACITOR AND

DIODE REMOVAL

1) Discharge the high voltage capacitor.

2) Disconnect the leadwire from fan motor, and high
voltage capacitor.

3) Remove the screw holding the suction guide
assembly to the oven cavity and remove the high
voltage diode earth screw.

4) Remove the screw holding the high voltage capacitor
bracket.

I. AIR DUCT ASSEMBLY REMOVAL

1) Disconnect the leadwire from lamp.

2) Remove the mounting screw to Latch Board.

J. MAGNETRON REMOVAL

1) Disconnect the leadwire from the high voltage
transformer.

2) Carefully remove the mounting screws holding the
magnetron to the waveguide.

3) Remove the magnetron assembly until the tube is
clear from the waveguide.

NOTE:

1. When removing the magnetron, make sure its
dome does not hit any adjacent parts, or it may be
damaged.

2. When replacing the magnetron, be sure to install
the magnetron gasket in the correct position and
be sure that the gasket is in good condition.

3. After replacing the magnetron, check for microwave
leakage with a survey meter around the
magnetron. Microwave energy must be below the

limit of 5 mW/cm2. (With a 275 ml. water load).

Make sure that gasket is rigidly attached to the

magnetron. To prevent microwave leakage,

tighten the mounting screws properly, making sure
there is no gap between the waveguide and the
magnetron.

Waveguide

Magnetron
Gasket

Magnetron

Dome

Waveguide
Bracket

Magnetron

H.V.
Transformer

Fan Motor ASS’Y

Suction
Guide

H.V.
Capacitor

H.V.
Diode

5-6

K. REMOVING THE TURNTABLE MOTOR

1) Remove the turntable.

2) Remove the turntable shaft VERY CAREFULLY
with a slotted screwdriver.

3) Lay the unit down on its back.

4) Remove the turntable motor cover.

The turntable base cover is easily removed by

pinching the six parts with a wire cutting.

5) Disconnect the leadwire from the turntable motor
terminals.

6) Remove the screw securing the turntable motor to
the oven cavity assembly.

7) After repairing the motor, rotate the removed
turntable motor cover.

8) Fit the turntable motor cover’s projecting part to the
base plate slit.

NOTE:

1. Remove the wire lead from the turntable motor
VERY CAREFULLY.

2. Be sure to grasp the connector, not the wires, when
removing.

L. INTERLOCK SYSTEM

1) INTERLOCK MECHANISM
The door lock mechanism is a device which has

been specially designed to eliminate completely
microwave activity when the door is opened during
cooking and thus to prevent the danger resulting
from the microwave leakage.

2) MOUNTING OF THE PRIMARY/MONITOR/
SECONDARY SWITCHES TO THE LATCH
BOARD

3) INSTALLATION AND ADJUSTMENT OF THE
LATCH BOARD TO THE OVEN ASSEMBLY

• Mount the latch board to the oven assembly.

• Adjust the latch board in the arrow direction so that

oven door will not have any play in it when the door
is closed.

• Tighten the mounting screw.

• Check for play in the door by pushing the door

release button. Door movement should be less
than 0.5 mm. (1/64 inch)

Don't push the door release button while making

adjustment. Make sure that the latch moves
smoothly after adjustment are completed and that
the screws are tight. Make sure the primary, monitor,
and secondary switches operate properly by
following the continuity test procedure.

PRIMARY
SWITCH

ADJUSTMENT
DIRECTION

MONITOR
SWITCH

SECONDARY
SWITCH

Wire Leads

Turntable Motor

A. PRIMARY INTERLOCK SWITCH TEST

When the door release button is depressed slowly
with the door closed, an audible click should be
heard at the same time or successively at
intervals. When the button is released slowly, the
latches should activate the switches with an
audible click.
If the latches do not activate the switches when
the door is closed, the switches should be a
adjusted in accordance with the adjustment
procedure. Disconnect the wire lead from the
primary switch. Connect the ohmmeter leads to
the common (COM) and normally open (NO)
terminal of the switch. The meter should indicate
an open circuit in the door open condition.
When the door is closed, the meter should
indicate a closed circuit.
When the primary switch operation is abnormal,
make the necessary adjustment or replace the
switch only with the same type of switch.

B. SECONDARY INTERLOCK SWITCH TEST

Disconnect the wire lead from the secondary
switch.
Connect the ohmmeter leads to the common
(COM) and normally open (NO) terminals of the
switch. The meter should indicate a open circuit in
the door open condition. When the door is closed,
meter should indicate an closed circuit. When the
secondary switch operation is abnormal, make the
necessary adjustment or replace the switch only
with the same type of switch.

C. MONITOR SWITCH TEST

Disconnect the wire lead from the monitor switch.
Connect the ohmmeter leads to the common
(COM) and normally closed (NC) terminals of the
switch. The meter should indicate closed circuit in
the door open condition. When the door is closed,
meter should indicate an open circuit. When the
monitor switch operation is abnormal, replace with
the same type of switch.

NOTE: After repairing the door or the interlock
system, it is necessary to do this continuity
test before operating the oven.

5-7

WARNING : FOR CONTINUED PROTECTION AGAINST EXCESSIVE RADIATION

EMISSION, REPLACE ONLY WITH IDENTICAL REPLACEMENT PARTS.

ALL THESE SWITCHES MUST BE REPLACED AT THE SAME TIME.

TYPE NO. SZM-V 16-FA-63 OR VP-533A-OF OR V-5230Q FOR PRIMARY SWITCH
TYPE NO. SZM-V 16-FA-62 OR VP-532A-OF OR V-5220Q FOR MONITOR SWITCH
TYPE NO. SZM-V 16-FA-63 OR VP-533A-OF OR V-5230Q FOR SECONDARY SWITCH

COMPONENTS TEST PROCEDURE RESULTS

SWITCHES Check for continuity of the Door Door
(Wire leads removed) switch with an Ohm-meter open closed

Primary
Switch

Monitor
Switch

Secondary
Switch

NOTE : After checking for the continuity of switches, make sure that they are

connected correctly.

M

O

INTERLOCK CONTINUITY TEST

COM

COM

COM

NO

NC

T

NO

T

ADJUST
DIRECTI

T

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE
OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER
OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS TEST PROCEDURE RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.
(Ohm-meter scale: Rx1 and Rx100)

• Primary winding

• Secondary winding

• Filament winding

2. Measure the resistance.
(Ohm-meter scale: Rx1000)

• Primary winding to ground

• Filament winding to ground

1. Measure the resistance.
(Ohm-meter scale: Rx1)

• Filament terminal

2. Measure the resistance.
(Ohm-meter scale: Rx1000)

• Filament to chassis

Approx.: 0.3 ~ 0.8 ohm
Approx.: 100 ~ 200 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

PRIMARY
TERMINAL

SECONDARY

FILAMENT
WINDING

COMPONENT TEST PROCEDURE

5-9

COMPONENTS TEST PROCEDURE RESULTS

HIGH VOLTAGE
CAPACITOR

HIGH VOLTAGE
DIODE

NOTE :
Some inexpensive meters
may indicate infinite
resistance in both direction.

Measure the resistance.
(Ohm-meter scale: Rx1000)

• Terminal to terminal.

Measure the resistance.
(Ohm-meter scale: Rx1000)

• Terminal to case.

Measure the continuity (Forward).
(Ohm-meter scale: Rx10000)

Measure the continuity (Reverse).
(Ohm-meter scale: Rx10000)

Normal: Momentarily indicates

several ohms, and
then gradually returns
to infinite.

Normal: Infinite.

Normal: Continuity.
Abnormal: Infinite.

Normal: Infinite.
Abnormal: Continuity.

NOTE: When testing the magnetron, be sure to install the magnetron gasket

in the correct position and be sure that the gasket is in good condition.

Antenna

Gasket

Chassis

Filament

5-10

COMPONENTS TEST PROCEDURE RESULTS

RELAY 2

FAN MOTOR
(Wire leads removed)

TURNTABLE
MOTOR
(Wire leads removed)

Check for continuity of relay 2 with an
ohm-meter.
(Remove wire leads from relay 2 and
operate the unit.)

Measure the resistance.
(Ohm-meter scale: R x 100)

Measure the resistance.
(Ohm-meter scale: R x 1000)

POWER
LEVEL

1 4 sec 18 sec
2 6 sec 16 sec
3 8 sec 14 sec
4 10 sec 12 sec
5 12 sec 10 sec
6 14 sec 8 sec
7 16 sec 6 sec
8 18 sec 4 sec
9 20 sec 2 sec

10 22 sec 0 sec

Normal:
A~B : Approx. 65 ~ 80 ohm
B~C : Approx. 10 ~ 30 ohm
A~C : Approx. 85 ~ 105 ohm

Abnormal: Infinite or several

ohm.

Normal: Approx. 100 ~ 150 ohm
Abnormal: Infinite or several

ohms.

NOTE : • A MICROWAVE LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS

SERVICED FOR ANY REASON.

• MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION.

• WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE
CONNECTOR, NOT THE WIRES.

Relay 1

Relay 2

A(RD)

B(BK)

C(WH)

TROUBLE SHOOTING

WHEN YOU GET A COMPLAINT FROM YOUR CUSTOMER, EVALUATE THE COMPLAINT CAREFULLY. IF
THE FOLLOWING SYMPTOMS APPLY, PLEASE INSTRUCT THE CUSTOMER IN THE PROPER USE OF THE
MICROWAVE OVEN. THIS CAN ELIMINATE AN UNNECESSARY SERVICE CALL.

5-11

CAUTIONS

1. Check grounding before checking for trouble.

2. Be careful of the high voltage circuit.

3. Discharge the high voltage capacitor. (See page 2-1)

4. When checking the continuity of the switches or of the high voltage transformer, disconnect one lead wire
from these parts and then check continuity with the AC plug removed. To do otherwise may result in a
false reading or damage to your meter.

CONDITION

Microwave oven

does not work.

Inserting many plugs into one
outlet and using
them at the same time
(blown fuse or breaker)

Microwave oven plug is not
inserted tightly.

Output power is too low. Low AC input voltage.

Food temperature is too low.

Using metallic ware and
allowing it to touch the oven
wall.

Sparks occur.

Inconsistent intensity of
microwave by their
characteristics.

1. Use plastic wrap or lid.

2. Stir once or twice while
cooking soup, cocoa or
milk, etc.

Uneven cooking.

Ceramic ware trimmed in
gold or silver powder is used.

Avoid using other electrical
appliances when you use the
microwave oven.

Insert microwave oven plug
securely.

Use the microwave oven at
adequate line voltage.

This may not be a defect.
It is possible that the food
should be cooked for a
longer time period.

Do not use metallic ware for
cooking except where noted
in the cooking guide.

Do not use any type of
cookware with metallic
trimming.

CAUSE REMEDY

5-12

CONDITION CHECK RESULT CAUSE REMEDY

1. Fuse blows. Continuity.

No continuity.

Continuity.

Shorted contact at
the primary switch.

Replace fuse,
primary, monitor,
secondary
switches.

No continuity.

Normal.

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Fuse blows again

Defective high volt­age transformer.

Replace high volt­age transformer.

Malfunction of the
monitor switch.

Replace fuse,
primary, monitor,
secondary
switches.

Check continuity
of monitor
switch (with
door closed).

Check continuity
of primary
switch (with
door opened).

Disconnect one
side of the wire
lead connected
from transformer
to the high
voltage
capacitor and
operate the unit.

Replace fuse

2. Fuse does not
blow.

No continuity.

Continuity.

No continuity.

Defective power
supply cord.

Replace power
supply cord.

Defective
thermostat.

Replace
thermostat.

Check continuity
of thermostat.

Check continuity
of power supply
cord.

(TROUBLE 1)

Oven does not operate at all and no input is accepted.

NOTE : All these switches must be replaced at the same time. Refer to page 5-6, 5-7

5-13

(TROUBLE 2) Oven seems to be operating but little heat is produced in oven load.

NOTE :

Simple test of power output-conducted by heating one liter water for one min. if available.
Minimum 8.5°C temperature rise is normal condition.

CONDITION CHECK RESULT CAUSE REMEDY

Output is low

Lower than 90% of
rating voltage.

Normal

Abnormal

Measure the
output power.

Defective
magnetron.

Replace
magnetron.

Decrease in power
source voltage
with load.

Suggest customer
contact local
electric power
utility company
or qualified
electrician.

Check the
power source
voltage.

5-14

CONDITION CHECK RESULT CAUSE REMEDY

No microwave
oscillation.

No continuity.

Continuity.

Abnormal

Defective high
voltage
transformer.

Replace high
voltage
transformer.

Normal

Defective timer
motor.

Replace timer
motor.

Check the timer
switch of timer
motor.(cooking
state)

Check high vol­tage transformer

Abnormal

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Normal

Check high vol­tage capacitor.

Abnormal

Defective high
voltage diode.

Replace high
voltage diode.

Normal

Check high vol­tage diode.

Abnormal

Defective
magnetron.

Replace
magnetron.

Check
magnetron.

(TROUBLE 3)

No microwave oscillation even though oven lamp and fan motor run.

NOTE : • Make sure the wire leads are in the correct position.

• When removing the wire leads from the parts, be sure to grasp the connector, not the wires.

• When removing the magnetron, be sure to install the magnetron gasket in the correct position
and in good condition.

LATCH BOARD PARTS

INTERIOR PARTS

BASE PLATE PARTS

OVEN CAVITY PARTS

DOOR PARTS

CONTROL PANEL PARTS

6-1

EXPLODED VIEW

INTRODUCTION

#EV#

MODEL: SBM6500W/SBM6500B

6-2

13552A

13213A

13581A

13720D

14970A

14026A

13536A

13352A

DOOR PARTS

#EV#

6-3

24781T

23572A

249401

26549T

WTT028

CONTROLLER PARTS

#EV#

6-4

WTT

010

WSZ185

WTT021

33112U

WTP

013

33052A

33390G

36549S

35889A

948502

OVEN CAVITY PARTS

#EV#

6-5

WSZ085

466001

43500A

44510A

466001

466003

LATCH BOARD PARTS

#EV#

6-6

INTERIOR PARTS

#EV#

56930V

WSZ002

50FZZA

56324A

55006F

55900A

56411A

WSZ002

WSZ002

WTT037

56549F

54974S

56912B

568771

55262A

6-7

56170D

WTT028

54810C

50CZZH

56851D

63302A

WSZ002

WTT021

65006B

63303A

BASE PLATE PARTS

#EV#