Sunbeam I85R, I85B User Manual

User Manual

WARMING PRODUCTS

IMPORTANT INSTRUCTIONSDO NOT DESTROY

As with all electrical products, misuse of product or failure to properly follow the instructions may cause overheating, fire, or personal injury. Please read the product label and all of the instructions before using your warming product.

1 Do not use this warming product with an infant, a child, an

incapacitated person, a paraplegic, a quadriplegic, a diabetic, one insensitive to heat such as a person with poor blood circulation, or anyone who cannot clearly understand the instructions and/or operate the controls.

2 Do not use with damaged cords. Damaged cords can lead to

fire. Do not trap, fold, cross, or pinch cords between bed slats, mattress, or springs, or against walls, footboards, or bed frame.

3 Do not dry clean this warming product. Cleaning liquid may

damage the insulation of the heating element. Improper laundering may cause problems with the heating wire which can lead to fire.

4 Do not pinch, flex, or expose the heating wire to rubbing. A

damaged heating wire may result in possible overheating or fire. 5 Turn off the control for the warming product when not using. 6 Keep control away from an open window. 7 Do not use pins; they may damage the electric wiring.

8 Be sure this blanket/mattress pad/throw is used only on an AC

supply current circuit of 110-120 volts. Do not use with an extension cord.

9 Excissive heating may result from folding blanket, when in

actual use.

10 Keep all dogs, cats, and other pets away from this warming

product. This is an electrical appliance that they can damage or be injured by.

11 Do not use blanket/mattress pad on a waterbed, sofa, bunk

bed, or mechanically adjustable bed and do not use throw on a waterbed, bunkbed, or mechanically adjustable bed.

12 Do not use another electronic heating device in conjunction

with your warming product.

13 Use the proper size blanket/mattress pad for your bed. For

example, use a Twin Size warming blanket on a Twin Size bed.

14 If the following Important Instructions are not followed the

warming product will not operate properly.

15 If you see the warming product operating improperly, unplug it

immediately and call Sunbeam Consumer Service at the 800 number listed under “How to Obtain Warranty Service”.

Warnings and Safeguards

Welcome

Thank you for choosing a Sunbeam®warming product. With your purchase you’ve made a real investment in your comfort and can look forward to staying warm and cozy for many cool days to come.

With over 50 years of experience and over 25 million households using a Sunbeam®warming product, you can rest comfortably knowing that Sunbeam®is the brand to trust…for quality and performance.

So get ready for a more restful sleep.

Table of contents

DD Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 2

Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 3

DD Convertible Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 4

Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 5

DD 2 Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 6

Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 7

DD Z Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 8

Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 9

DD Gradient Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11

Warming Blanket . . . . . . . . . . . . . . . . . . . . . . 10

Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . 11

DDY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2-13

Warming Blanket . . . . . . . . . . . . . . . . . . . . . . 12

Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . 13

LED Throw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Auto-off feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 7-18

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

How to obtain warranty service . . . . . . . . . . . . . 20

DD Remote

Features:

• REMOTE CONTROL – sends heat level control commands to the base unit and adjusts the blankets warmth accordingly.

• ELECTRONIC DIGITAL CONTROL – for easy setting with backlit LCD

• AUTO-OFF – 10 hour independent auto-off (see page 15)

• 10 TEMPERATURE SETTINGS– select your personal comfort

• PRE-HEAT– for cozy warmth before bedtime

• SOLID STATE – for accurate and consistent heat control

• EASY OPERATION– Electronic digital controller for easy operation

• EASY GRIP – ergonomic control for easy operation

• CORDLESS – no more wires to tangle

• AUDIBLE BEEP – when changing heat settings, on/off setting and automatic programming selections.

Pre-heat

1 To use the preheat feature, simply press the round “On/Off” button and

then press the “Preheat” button. The preheat function will heat the bed for a period of 30 minutes.

2 To reset the preheat feature, simply press the “On/Off” button OFF. 3 To turn back ON repeat step1.

CAUTION: Do not plug main power cord into the wall outlet until you have completely set

up your warming blanket per the instructions.

IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING BLANKET WILL NOT WORK.

• Disconnect power cord from wall before detaching control from warming blanket

• Always make sure cords are NOT trapped or pinched between bed slats, mattress, springs, against wall, foot board or bed frame.

1 Place the warming blanket on the bed with the label side facing outward. 2 Plug cord into the module at the bottom of the warming

blanket until the plastic hinges click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection.

3 Run the cord under the bed, not between the mattress and box

springs. Avoid any tangling or pinching.

4 Place the base unit on the floor under the bed. 5 Place the remote control where it is convenient for you. 6 Plug warming blanket power cord into a 110-120 volt wall

outlet.

CAUTION: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet. If the plug does not fit in the outlet, reverse the plug. Do not attempt to force the plug.

IMPORTANT

Set Up WARMING BLANKET

Using your Control:

1 To turn the control on, simply press the “On/Off” button. The backlit display light will illuminate and begin to warm

at the comfort setting last used. CAUTION: ALWAYS turn the warming blanket “Off” when not in use. 2 To turn the warming blanket OFF simply press the “On/Off” a second time.

Setting the control side (Queen or King blankets only)

The “left” control can operate the left or both sides, and the “right” control can operate the right or both sides. (If you have a Twin or Full size blanket, the remote control operates the entire blanket.) Each person has complete control over his/her temperature comfort level for the ultimate in individualized comfort.

You can use one remote control to operate both sides of the blanket (both sides of the blanket will have the same heat level). Or, you can use two remote controls to set separate heat levels for each side of the blanket.

Installing the Batteries

1 Remove the battery compartment door from the back of

the remote control

2 Insert three AAA batteries, matching the + and - markings

in the battery compartment to the markings on the batteries

3 Replace the battery compartment door 4 If your blanket has two remote controls, repeat steps

1 – 3 to install batteries in the second remote control.

CAUTION: Do not plug main power cord into the wall outlet until you have completely set

up your warming blanket per the instructions.

IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING MATTRESS PAD WILL NOT WORK.

• Disconnect power cord from wall before detaching control from warming mattress pad

• Always make sure cords are NOT trapped or pinched between bed slats, mattress, springs, against wall, foot board or bed frame.

1 Place the warming mattress pad on the bed with the label side facing outward. 2 Plug cord into the module at the bottom of the warming

mattress pad until the plastic hinges click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection.

3 Run the cord under the bed, not between the mattress and box

springs. Avoid any tangling or pinching.

4 Place the base unit on the floor under the bed. 5 Place the remote control where it is convenient for you. 6 Plug warming mattress pad power cord into a 110-120 volt

wall outlet.

IMPORTANT

Set Up WARMING MATTRESS PAD

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate equipment.

DD Convertible

Features:

• ELECTRONIC DIGITAL CONTROL – for easy setting with backlit LCD

• AUTO-OFF – 10 hour independent auto-off (see page 15)

• 10 TEMPERATURE SETTINGS– select your personal comfort

• PRE-HEAT– for cozy warmth before bedtime

• SOLID STATE – for accurate and consistent heat control

• EASY OPERATION– Electronic digital controller for easy operation

• EASY GRIP – ergonomic control for easy operation

• ROOM TEMPERATURE COMPENSATION–

• INTERCHANGEABLE TOP –

Pre-heat

1 To use the preheat feature, simply press the round “On/Off” button and

then press the “Preheat” button. The preheat function will heat the bed for a period of 30 minutes.

2 To reset the preheat feature, simply press the “On/Off” button OFF. 3 To turn back ON repeat step1.

CAUTION: Do not plug main power cord into the wall outlet until you have completely set up

your warming blanket per the instructions.

IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING BLANKET WILL NOT WORK.

• Disconnect power cord from wall before detaching control from warming blanket

• Always make sure cords are NOT trapped or pinched between bed slats, mattress, springs, against wall, foot board or bed frame.

1 Place the warming blanket on the bed with the label side facing outward. 2 Plug cord into the module at the bottom of the warming

blanket until the plastic hinges click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection.

3 Run the cord under the bed, not between the mattress and box

springs. Avoid any tangling or pinching.

4 For dual control warming blankets, place primary control (label

on back of control) on the same side of the bed as the blanket label side.

5 For single control warming blankets, the control can be placed

on either side of the bed.

6 Plug warming blanket power cord into a 110-120 volt wall

outlet.

IMPORTANT

Set Up WARMING BLANKET

n O

ff O

Off

Using your Control:

1 To turn the control on, simply press the “On/Off” button. The backlit display light will

reset itself by flashing “FF” and then will light showing the previous setting the unit was set during the last use and will begin to warm.

CAUTION: ALWAYS turn the warming blanket/warming mattress pad “OFF” when not in use.

2 To turn the warming blanket/warming mattress pad OFF simply press the “On/Off”

button.

CAUTION: Do not plug main power cord into the wall outlet until you have completely set up your warming blanket per the instructions.

IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING MATTRESS PAS WILL NOT WORK.

• Disconnect power cord from wall before detaching control from warming mattress pad

• Always make sure cords are NOT trapped or pinched between bed slats, mattress, springs, against wall, foot board or bed frame.

1 Place the warming mattress pad on the bed with the label side facing outward. 2 Plug cord into the module at the bottom of the warming

mattress pad until the plastic hinges click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection.

3 Run the cord under the bed, not between the mattress and box

springs. Avoid any tangling or pinching.

4 For dual control warming mattress pads, place primary control

(label on back of control) on the same side of the bed as the blanket label side.

5 For single control warming mattress pads, the control can be

placed on either side of the bed.

6 Plug warming mattress pad power cord into a 110-120 volt

wall outlet.

IMPORTANT

Set Up WARMING MATTRESS PAD

DD 2

+ 17 hidden pages