Ceramic Heater
Digital Thermostat Control
1800W oscillating heater with timer
Instruction Booklet
HE2125
Please read these instructions carefully and
retain for future reference.
Contents
Sunbeam’s Safety Precautions 1
Sunbeam’s Safety Precautions for your Heater 2
Sunbeam’s Total Safety System 3
Features of your Compact Oscillating
Ceramic Heater 4
Using your Compact Oscillating
Ceramic Heater 6
Using the Oscillation function 8
Resetting the Total Safety System 8
Troubleshooting Guide 9
Care and Cleaning 9
Sunbeam’s Safety Precautions
Sunbeam are very safety conscious when
designing and manufacturing consumer products,
but it is essential that the product user also
exercise care when using an electrical appliance.
Listed below are precautions which are essential
for the safe use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and
before cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• This appliance is not intended for use by young
children or infirm persons unless they have
been adequately supervised by a responsible
adult to ensure that they can use the appliance
safely.
• Young children should be supervised to ensure
that they do not play with the appliance.
• Never leave an appliance unattended while
in use.
• Do not use an appliance for any purpose
other than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• For safety reasons and to avoid maintenance
by unskilled persons, some appliances are
‘sealed’ using tamperproof screws. Such
appliances should always be returned to the
nearest Sunbeam Appointed Service Centre
for adjustment or repair if required.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water
or any other liquid unless recommended.
• Appliances are not intended to be operated by
means of an external timer or separate remote
control system.
If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
1
Sunbeam’s Safety Precautions
• This heater becomes hot during use. To avoid
burns, do not let bare skin touch hot surfaces.
If provided, use handles when moving this
heater. Keep combustible materials such as
furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (90cm) away from the
front of the heater and keep them away from
the sides and rear.
• Extreme caution is necessary when any heater
is used by or near children or invalids and
whenever the heater is left unattended.
• Always unplug the heater when not in use.
• Do not use outdoors.
• Do not run the cord of the heater under
carpeting. Do not cover the cord with throw
rugs, runners or other floor coverings. Arrange
the cord away from traffic areas where it will
not be tripped over.
• Do not locate the heater immediately below a
socket outlet.
• Do not use this heater in the immediate
surrounds of a bath, shower, laundry area or
swimming pool.
• Do not insert or allow foreign objects to enter
any ventilation or exhaust openings as this may
cause electric shock or fire, or damage to the
heater.
• To prevent a possible fire, do not block air
intakes or exhaust in any manner. Do not use
on soft surfaces, such as beds, where opening
may become blocked.
• A heater has hot and arcing or sparing parts
inside. Do not use it in areas where petrol,
paint or flammable liquids are used or stored.
• To prevent overheating, do not cover the
heater.
Important instructions – retain for
future use.
If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
2
Sunbeam’s Total Safety System
Safety auto shut off
Your Sunbeam Compact Oscillating Ceramic
heater is equipped with a safety system that
detects any abnormally high temperatures
within the heater and automatically shuts
it off to prevent overheating. If the heater
overheats an alarm will sound continuously,
the LED’s will flash and the LCD screen will
show 00.
Do not operate the heater with the alarm
sounding. Immediately turn the heater off at
the power outlet and check that there aren't
any objects on or around the heater.
This first stage of the safety system requires
the user to manually reset the heater for it to
resume operation.
For instructions on how to reset your heater,
see page 8.
Thermal back-up device
In addition to this automatic shut-off, your
heater contains an over temperature thermal
back-up device to provide additional backup protection. If the heater is in an overheat
situation, the back-up device will operate,
stopping the power flow to the element and
fan.
In the event that the back-up device is
activated, the heater will need to be reset.
For instructions on how to reset your heater,
see page 8.
3
Features of your HE2125
Oscillating Ceramic Heater
Power ON light
Illuminates to indicate that the heater is
connected to the power outlet.
LCD screen
The LCD screen displays the temperature setting.
Mode button
Press the mode button to select the desired
operating mode:
LOW HEAT, HIGH HEAT,
AUTO OR FAN
Fan setting
Ideal for circulating cool air in summer, the fan
setting operates the fan without heat.
Timer button
Press and hold to activate timer function.
ON/OFF button and thermostat dial
4
Oscillation function
The heater oscillates 90 degrees to provide
greater heat distribution. Simply press the
oscillation button (OSC) to activate this
function.
Electronic thermostat
The electronic thermostat allows for precise
temperature control. Select the auto mode
to set the electronic thermostat and turn
the thermostat dial to the desired heat
setting. Once your desired temperature is
reached, the heater will cycle on and off
to maintain it.
Thermostat dial
When in auto mode, turn the thermostat dial
to select your desired temperature.
Ceramic element
The 1800 watt ceramic element is more
efficient than other element types as it
converts more electricity into heat.
Ceramic elements are also safer than other
element types. They do not glow and operate
at lower temperatures than other heaters.
They convert more energy into heat, thereby
using less power.
Safety auto shut-off
The safety auto shut-off system detects any
abnormally high temperature variations within
the heater and automatically switches it off
to prevent overheating.
5
Using your Compact Oscillating
Ceramic Heater
1. Place the heater on a flat level surface and
ensure that the air intake and outlet are
clear of obstructions.
2. Insert the plug into a 230/240V power
outlet and turn the power on.
3.The power on light will illuminate and the
unit will emit a “ beep”.
NOTE: When the heater is switched on at
the power outlet it will automatically be in
Standby mode.
4. Press the power button (
heater. Use the Mode button to scroll for
your desired setting. See settings below:
High – Highest heat setting
Low – Lowest heat setting
AUTO – For operating the digital
thermostat
FAN – Operates without heat
5. To switch your heater off, press the power
(
) button.
) to activate the
Setting the digital thermostat
The digital thermostat allows you to select
your desired temperature between 15ºC and
30ºC.
NOTE: When the air temperature reaches 2
degrees above the selected temperature the
unit will turn off.
1. Press the Mode button until the Auto mode
is displayed. The LCD will then flash 25
degrees as the default temperature.
2. Turn the thermostat dial to select your
desired temperature. After 5 seconds the
LCD will stop flashing and will display the
room temperature.
NOTE: The temperature range is from
15ºC to 30ºC.
3. To help maintain the room temperature for
longer, the unit will turn off automatically
when the room temperature is 2ºC above
the set temperature.
NOTE: It is normal for the heater to cycle
on and off as it maintains the preset
temperature. To prevent the unit from
cycling, raise the thermostat setting.
6
Using your Compact Oscillating Ceramic Heater continued
Timer function
The timer function allows you to pre-set the
unit to switch off after the selected time.
Choose from half hour increments up to 7.5
hours.
LED Setting Time Till OFF (hh:mm)
0.5
00:30
1
2
4
01:00
0.5
1
2
4
01:30
0.5
1
2
4
02:00
0.5
1
2
4
02:30
0.5
1
2
4
03:00
0.5
1
2
4
03:30
0.5
1
2
4
04:00
0.5
1
2
4
1. Press and hold the Timer/Mode button until
the timer LED’s Illuminate.
2. Select the desired shut off time by rotating
the thermostat dial until you reach the
correct time.
3. Once the LED stop flashing, the timer is
set.
LED Setting Time Till OFF (hh:mm)
0.5
04:30
1
2
4
05:00
0.5
1
2
4
05:30
0.5
1
2
4
06:00
0.5
1
2
4
06:30
0.5
1
2
4
07:00
0.5
1
2
4
07:30
0.5
1
2
4
7
Using the Oscillation Function
The 90 degree oscillation function can be
used in any mode.
1. Press the oscillation button (OSC) on the
front panel of the heater. The heater will
then begin to oscillate from side to side.
2. To stop the heater from oscillating, simply
press the oscillation button (OSC) once
again.
Resetting the Total Safety System
Resetting the safety auto shut-off
The safety auto shut-off detects any
abnormally high temperatures within the heater
and shuts it off to prevent overheating. Should
the safety auto shut-off activate and switch off
the heater, it will need to be reset.
1. Unplug the heater and wait 10 minutes for
the unit to cool down.
2. After 10 minutes, plug the heater in again
and operate as usual.
Resetting the thermal backup device
In addition to the safety auto shut-off, your
heater also contains a thermal back-up
device for additional protection. Should the
thermal back-up device activate and switch
off the heater it will need to be reset.
To reset the heater, follow steps 1 and 2 on
this page.
8
Troubleshooting Guide
If your heater fails to operate check the
following:
• Make sure the electrical outlet or circuit
breaker is working.
• Check for obstructions. Never cover the
heater. Never attempt to open the heater.
If the fault persist please call Sunbeam
Customer Service for assistance.
Care and Cleaning
Ensure that the heater is switched off and
disconnected from the power outlet before
cleaning.
Carefully wipe the exterior of the heater with
a soft damp cloth and dry thoroughly with a
dry cloth.
• Check that the thermostat is not set too
low. Turn the thermostat dial clockwise to
adjust the electronic thermostat until the
heater restarts.
• The safety auto shut-off may have
activated, so follow the instructions for
resetting on page 8.
Over time, dust may accumulate on the front
grilles. This can be removed by wiping with a
damp cloth.
Store the heater in a cool dry place when
not in use. Store the heater in its carton if
possible.
9
Notes
Notes
Notes
2 Year Warranty
This Sunbeam product is covered by a 2 year replacement warranty,
which is in addition to your rights under the Australian Consumer Law
(if your product was purchased in Australia) or New Zealand Consumer
Guarantees Act (if your product was purchased in New Zealand).
Should you experience any difficulties with your
product during the warranty period, please contact
our customer service line for advice on 1300 881 861
in Australia, or 0800 786 232 in New Zealand.
Alternatively, you can send a written claim to
Sunbeam to:
Australia
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
New Zealand
Level 6, Building 5, Central Park,
660-670 Great South Road,
Greenlane, Auckland
Upon receipt of your claim, Sunbeam will seek to
resolve your difficulties or, if the product is defective,
advise you on how to obtain a replacement or refund.
To assist us in managing warranty claims, we
recommend you register your product as soon as
practicable after purchase by creating a MySunbeam
account on our website and send a copy of your
original receipt to Sunbeam.
In order to make a claim under our warranty, you must
have the original proof of purchase documentation for
the product and present it when requested .
Should your product develop any defect within
2 years of purchase because of faulty materials or
workmanship, we will replace or repair it, at our
discretion, free of charge. A product presented for
repair may be replaced by a refurbished product
of the same type rather than being repaired.
Refurbished parts may be used to repair the product.
Our replacement or repair warranty only applies
where a defect arises as a result of faulty material or
workmanship during the warranty period. Your warranty
does not cover misuse or negligent handling (including
damage caused by failing to use the product in
accordance with this instruction booklet), accidental
damage, or normal wear and tear.
Your warranty does not:
• cover freight or any other costs incurred in making a
claim, consumable items, accessories that by their
nature and limited lifespan require periodic renewal
(such as filters and seals) or any consequential loss
or damage; or
• cover damage caused by:
- power surges, power dips, voltage supply problems,
or use of the product on incorrect voltage;
- servicing or modification of the product other than
by Sunbeam or an authorised Sunbeam service
centre;
- use of the product with other accessories,
attachments, product supplies, parts or devices
that do not conform to Sunbeam specifications; or
- exposure of the product to abnormally corrosive
conditions; or
• extend beyond 3 months if the product is used
in commercial, industrial, educational or rental
applications.
The benefits given to you by our warranty are in addition
to other rights and remedies under law in relation to the
product.
In Australia our goods come with guarantees that cannot
be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure
and for compensation for any other foreseeable loss or
damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Our goods also come with guarantees that cannot be
excluded under the New Zealand Consumer Guarantees
Act.
If your warranty claim is not accepted, we will inform
you and if requested to do so by you, repair the
product provided you pay the usual charges for such
repair. You will also be responsible for all freight and
other costs.
Should your product require repair or service after the
warranty period, contact your nearest Sunbeam service
centre. For a complete list of Sunbeam’s service
centres, visit our website or call our customer service
line for advice on 1300 881 861 in Australia,
or 0800 786 232 in New Zealand.
Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Visit www.sunbeam.com.au
Or call 1300 881 861
In New Zealand
Visit www.sunbeam.co.nz
Or call 0800 786 232
is a registered trademark.
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright.
ABN 45 000 006 771
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Level 6, Building 5, Central Park
660-670 Great South Road
Greenlane, Auckland
New Zealand
Sunbeam Corporation is a division of GUD Holdings Ltd.
Sunbeam Corporation Limited 2013.
10/13
Loading...