SUNBA 604-22X, 405-36X, 301-3X, 601-AHD20X, 301-AHD3X Operating Instructions Manual
...
SUNBA® PTZ Camera
Analog
User Manual
Dedicated PTZ Camera Professional
2017/04
Series
( Analog-HD / CVBS )
Version 3.0
Version 3.0
The following content is guaranteed to be up-to-date at the time
of release. For latest information, please refer to www.sunbatech.com
A decoder can be a DVR or a video capture card. Some TV (with built-in
decoder) also supports CVBS signal. See the compatibility graphs below.
FCC Warning (U.S.A)
The device has been tested in compliance with limits set by Part 15 of
Federal Communication Commission (Class B). The operation of the
device is thus limited by the following two conditions:
1) it is not permitted to cause harmful interference to any authorized
radio communications, and 2) it must accept any interference it receives.
WARNING: Please test the camera locally by directly
connecting to the default power adapter from the package
before mounting it outside. Stay at least 24 hours to test
both daytime and night vision IR LED.
1.Camera Compatibility
Sunba Analog Camera Category
A.CVBS 960H Signal Analog Camera
Model: 604-22X, 301-3X, 405-22X, 604-36X, 405-36X
B.AHD 1080P Signal Camera
Model: 601-AHD20X, 301-AHD3X, 405-AHD20X, 805-AHD20X
Analog cameras require a decoder to display images on a
monitor. Sunba Analog PTZ camera requires Pelco D protocol
to support PTZ.
AHD1080P
Not the same type
of analog-HD signal
HD-TVI
HD-SDI
HD-CVI
Lorex MPX
DVR
DVR
DVR
×
- 01 -
Incompatible DVR will result in problems such as B/W display,
no video or the loss of PTZ control.
Compatibility Chart
Stage1:Before Mounting Outside
2.Camera Installation
DVR
CVBS
AHD1080P
CVBS
AHD1080P
CVBS
AHD1080P
960H DVR
AHD 1080P DVR
(AHD-H)
AHD 720P DVR
(AHD-M)
Use Default 12DVC Power Adapter! No Power Extension in Testing Phase!
Adapter
Adapter
A
B
VGA
RS485
DVR
BNC
DC12V
- 02 -
When you rst receive the PTZ camera, please make sure it works properly
before mount the camera outside. Note PTZ dome cameras have higher
power requirements than bullet cameras and corresponding IP cameras.
Therefore, how the unit is powered can be critical to its functionality.
Please make sure the unit itself is working, and try eliminating all cabling
factors to set up the bench test.
In short, in a bench test, do NOT extend the power line. Please connect
the camera with its default adapter.
The reason you should NOT extend the power cable during the bench
test is because DC power drops along the cable. Underpower can cause
problems such as 1) screen ickering, 2) unstable infrared (on/off automa-
-tically) and 3) camera spinning recklessly. A bench test helps you rule out
all problems caused by power supply.
For example, if you have previously wired a xed lens bullet camera and
you remove the old camera and adopt old wires directly on Sunba PTZ
dome camera, this is likely NOT working given two units have different
power requirements.
Indoor Bench Test
How to Test Locally
Why Test Locally
Don’t:
A
B
BNC
DC
Do not directly apply the old wirings for bullet cameras
on dome Cameras.
- 03 -
RS485 Connector Type A:
RS485 Connector Type B:
Stage2:Permanent Installation (with DVR)
A
B
A
B
Blue side goes to polar A on the
RS485 port of the DVR
Orange side goes to polar B on
the RS485 port of the DVR
Power
Video
Twisted Pair Cable
Twisted Pair Cable
BNC
DC12V
Power
Video
PTZ Control
PTZ Control
BNC
DC12V
- 04 -
Loading...