Sumsung LED Display Installation Manual

LED Display

Installation Manual

Ver. 4.2

IER / IER-F / IFR /IFR-F Series

LH0**IER*LS , LH0**IER*FS

LH0**IFR*LS , LH0**IFR*FS

LED R&D Lab(VD)

Revision History

Version Date (Y/M/D) Description

2.0 2020/03/20 New Release

3.2 2020/06/22 Add SNOW-1810U installation and picture setting

3.3 2020/08/07 Add test pattern function

3.4 2020/08/21 Adjust Power consumption info and Table of contents + Appendix

3.5 2020/09/04 Add the luminance function of the operation for the mixed connections

3.6 2020/11/02 Modify dehumidification mode

3.7 2020/11/16 Add Network IP Setting by USB

3.8 2020/11/27 Update LSM guide

3.9 2020/12/01 Update Picture Option

4.0 2020/12/02 Update Dehumidification Guide

4.1 2020/12/14 Update Ventilation Guide

4.2 2020/12/28 AC placement guide to prevent condensation

1

LED R&D Lab(VD)

This contents must be noticed to customer.

Please print this page and hand it to user.

Dehumidification guidance – during installation

 When moist gets into LED package because of high humidity, ‘Line defect’ can

be caused by electrical short inside of LED Package.

 For keeping the best quality of products during installation, please refer to the

below cautions.

- If the condition meets one of the below cases at least, dehumidification MUST be
processed. Do not play any contents on the screen before dehumidification finishes.

∙ Case when vacuum packaging is already unsealed before unpacking products.

∙ Case when environment condition is worse than Samsung working condition (0°C~40°C/10~80%RH).

∙ Case when it elapses longer than 7 days after unpacking them, even though the environment condition

satisfies Samsung working condition (0°C~40°C/10~80%RH).

∙ Case when production date on the label elapses more than 6 months, even though vacuum packaging is

sealed.

∙ Case when volatile chemicals such as oil paint, solvent are used in same place of installation.

(You can refer to Product Information and Precautions for Installation part in detail.)

- If the screen needs dehumidification on installation, MUST follow the directions of next page.

This contents must be noticed to customer.

Please print this page and hand it to user.

Dehumidification guidance – during installation

 How to install the screen in the case that dehumidification is necessary

※ Before finishing the directions explained in next pages, never play other contents or use them.
※ If the installation site has higher humidity, it is highly recommended to use dehumidifier.

(If A/C turned off after working hour, it may make humidity higher and cause line defects.)

※ Chilled air from A/C should never touch LED surface directly.
※ If thermo-hygrometer is equipped on the site while the screen is installed, it is useful to analyze

the cause of line defects.

1. Play a specific pattern of LSM program without any cabinets.
(This pattern should be used. If other pattern is used, it can cause line defects.)

① Select S-Box and Test Pattern

② Set darker gray pattern among various patterns.

2. Inspect cabinets with darker solid patterns(W/R/G/B) and turn off cabinets.
(It should take less than 30 seconds to show each solid patter and you can refer to

Screen check’ category in detail.)

‘Process of

This contents must be noticed to customer.

Please print this page and hand it to user.

Dehumidification guidance – during installation

 How to install the screen in the case that dehumidification is necessary.

3. While installing cabinets, S-Box should play only this pattern.

• Check S-Box shows the pattern through monitor connected to S-Box service port.

• After installing each cabinet, check whether the pattern is shown in it.

• OCM cable connection can be checked through this.

• Before turning off S-Box, turn off the cabinets, first.

• After being sure S-Box plays this pattern, turn on the cabinets.

4. After completing installation of cabinets, start 24hr dehumidification process.

5. After finishing 24hr dehumidification process, do edge correction and module calibration.

This information should be noticed to customer.

Please print this page and hand it to user.

Dehumidification guidance – during operation

• Electrical short in package is possible to happen during products are working.

• For keeping quality of products during installation, please refer below cautions.

– If one of below case meet during operation, MUST do dehumidification process.

 Case when environment condition is exceed operation condition.

 Case when products are not working more than 1 month, even though environment condition is under

operation condition.

– When environment condition is exceed operation condition, products are out of warranty.

Please check environment condition.

– Even products are operating, if the installed place have extra construction such as interior

modification, MUST do dehumidification following installation condition.

– It is possible to happen dew condensation on surface of products, even though working on

operating condition. When happening dew condensation, MUST operate after cleaning the dew

condensation & dehumidification.

This information should be noticed to customer.

Please print this page and hand it to user.

Dew condensation due to overcooling

 Even though meet with Samsung recommended operation

condition, dew condensation is possible to happen when

surface of products is colder than environment temperature or

hot & humid air blow to cooled surface of products.

(cf : Principle of happening dew on surface of glass which have ice)

 Case when dew condensation is happen on products, it is

possible to be the root of defect. In this case, it is possible to

be out of warranty.

This information should be noticed to customer.

Please print this page and hand it to user.

Prevent condensation due to A/C

 Make sure that the cold air does not blow directly on the screen.

– When the cold air from A/C (air conditioner) blows directly onto the screen surface,

condensation may occur depending on the ambient humidity and temperature of

screen surface.

– If the A/C and screen are close, install a wind deflector as shown in the figure

below to prevent condensation.

Install the wind deflector toward the screen.

Guidance of latest firmware

• When install products, please update latest firmware on online

- You can download latest firmware from SLM site.

 URL of SLM Page : https://www.secslm.com

 After login  Help  Download Center에서 Download

 Before you download firmware, you MUST check same firmware of model

(marked red letter in below) & upper number of version (marked blue in below).

Cabinet : Main - L-xxxMWWAC-nnnn.n  xxx = Pan name, nnnn.n = version

FPGA - aabbd_ddddd  aa = pixel pitch, bb = LED package type, d_ddddd= version

Example : IER P2.5  Cabinet : L-IERMWWAC-1003.1, FPGA : 25252-31046

S-box : TB-KTM2SBMDWWC_100x.x

- You can update firmware through LSM.

 Please refer ‘7-1 PC control program’ for the way to update firmware.

8

Table of Contents

1. Product Information and Installation Precautions (P.7)

2. Preparation for Cabinet Installation (P.18)

3. Frame Kit (P.22)

4. Frame Installation (P.23)

5. Cabinet + Frame Installation (P.31)

6. S-Box Installation and Connection (P.35)

7. Settings / How to Use (P.54)

8. Power and Cable Connection (P.73)

9. Seam Adjustment (P.79)

Appendix. IER-F/IFR-F series Installation Manual (P.81)

Appendix 1. S-BOX Network IP Set (P.108)

Appendix 2. IFR P1.5 Screen FAN guide (P.109)

9

LED R&D Lab(VD)

Installation Table

1. Product Information and Installation Precautions

◆ Model Line-up

- This Manual is an Installation Manual for IER/IFR(Appendix. IER-F/IFR-F), which contains information of

models below (Installation process is same for each pitch model)

Models Product Appearance and Information

IER/IFR series

IER-F/IFR-F series

remarks

of Contents

See pages 2 to 76

For different types and Curved installations
Made in 1⁄4 size of IER/IFR.
Recommended mix installation with IER/IFR.

IER/IER-F Series : Using Copper Wire LEDs

IFR/IFR-F Series : Using Gold Wire LEDs High Luminance Models

See 77 to 96 pages

10

LED R&D Lab(VD)

1. Product Information and Installation Precautions

of

connection

◆ Model specification

Resolution

Cabinet

consumption(W)

number

Brightness

Spec.

Size

(mm)

Number of

Module

Weight

(Cabinet)

Power

Max

(Set)

(nit)

IER / IFR IER-F / IFR-F

P1.5 P2.0 P2.5 P4.0 P1.5 P2.0 P2.5 P4.0

Width

height

Ver. 640 480 384 240 160 120 96 60

Hor. 360 270 216 135 360 270 216 135

11.8kg 12.4kg

260 / 360W 180 / 260W 150 / 260W 80 / 90 W 60 /80 W 50 / 80W 50 / 80W

110V 2 / 1 set 3 / 2 set 4 / 2 set 10 / 7 set 10 / 7 set 10 / 7 set

220V 4 / 3 set 6 / 4 set 7 / 4 set 20 / 15 set 20 / 15 set 20 / 15 set

Peak

Max

1000 / 1600 1200 / 1600 1200 / 2400 1200 / 1500 1000 / 1600 1200 / 1600 1200 / 2400 1200 / 1500

500 / 800 600 / 1000 600 / 1000 600 / 900 500 / 800 600 / 1000 600 / 1000 600 / 900

960 240

540 540

4 x 3, 12ea 1 x 3, 3ea

IER : 10.8kg
IFR : 12.4kg

3.2kg

FHD

Screen

FHD 3x3, 9set 4x4, 16set 5x5, 25set 8x8, 64set - -

UHD 6x6, 36set 8x8, 64set

10x10,
100set

16x16,
256set

※ Installation with IER/IFR of same pitch is recommended.

11

LED R&D Lab(VD)

1. Product Information and Installation Precautions

◆ Frame Kits configuration (See page 22.)

Frame kit Configuration

for installation

VG-LFR84FWL

VG-LFR53FWL

VG-LFR52SWL

VG-LFR51PWL

VG-LFR11SWL

8*4 (32 sets)

5*3 (15 sets)

5*2 (10 sets)

5*1 P (15 sets) PIVOT installation

1*1 (1 set)

Remarks

Narrow

◆ Cabinet information

※ Please refer to Appendix for information of IER-F / IFR-F Frame Kit

<5*3 Frame>

◆ SBB-SNOWJAU, SBB-SNOWJMU, SBB-SNOWRAF

(S-Box, I/G)

12

<S-Box> <I/G>

(Interface Gender)

LED R&D Lab(VD)

1. Product Information and Installation Precautions

◆ Installation precautions (LED damage)

Precautions Images

[Be careful of external impact or dropping]

① After removing the Cover-Corner from the product prior to installation,

exercise caution to ensure that the LED surface is not exposed to physical

impact and the product is not dropped onto the floor.

② Do not place the product on a vibrating object. Make sure the LED surface

does not face down onto the floor.

③ Exercise caution to ensure that the corners of the LED module are not

damaged due to contact with external factors.

④ Make sure the number of loaded rows does not exceed 12.

[Be careful of LED damage due to static electricity]

▶ Do not touch the LED surface with bare hands without anti-static gloves.

[Be careful of LED damage due to metallic foreign material]

▶ Exercise caution to ensure that metallic foreign material is not attached to

the LED front.

▶ If metallic foreign material is attached, remove the module and use a

MODULE

Front

① ②

③ ④

Metallic
foreign

material

magnet to remove the foreign material.

13

LED R&D Lab(VD)

1. Product Information and Installation Precautions

◆ Heat protection guide

 Requirements for indoor installation

- Applicable to use of SAMSUNG wall mount (compliant with ADA)

∙ Gap between the product front and the wall: 99.5 mm

∙ Gap between the product rear and the wall: 35.5 mm

- Entry of sunlight

∙ If sunlight enters through glass windows or outer walls of the building,

contact Company HQ for assistance.

- Cold/warm air from HVAC system

∙ Make sure cold or warm air (especially warm air) from an HVAC system

※ This page is written based on the Full white,

650 nit (back light 7) version

※ ADA: Americans with Disabilities Act

99.5 mm

Outdoor temperature

measurement position

wall

does not reach the product.

- Outdoor temperature measurement position

∙ Center of the product or the inlet area

14

Outdoor temperature

measurement position

35.5 mm

LED R&D Lab(VD)

1. Product Information and Installation Precautions

Outdoor
air temp.

 Fan flow rate depending on the number of installed cabinet rows

No. of rows

1 to 3
Rows

※ CFM = cubic feet per minute

4 Rows 5 Rows 6 Rows 7 Rows 8 Rows 9 Rows 10 Rows

※ Measurement based on one column

Below 25℃

Fan is not
necessary

25℃ to 30℃

※ Example) If outdoor air temperature is 30℃ and cabinets are

arranged in a 5x4 (horizontal x vertical) configuration,
what is the total CFM ?

→ 70 [CFM/column] x 5 [column]=350 [CFM]

Fan is not necessary

70 80 100 110 130 145 160

70 80 90 100

4 Rows

Total minimum flow rate 350 CFM

70 CFM 70 CFM 70 CFM 70 CFM70 CFM

FAN

Outdoor air

temperature is

30℃

5 Columns

※ For installation under other conditions not covered in this guide, contact the Development Team.

15

Air vent area

LED R&D Lab(VD)

1. Product Information and Installation Precautions

• Requirements for using FAN

– Air vent: Should only be installed on the bottom

– Upper portion: Seal the entirety, except the fan outlets

Location of FAN

Shape of FAN unit

Seal the left and right sides

WALL

Seal the left and

right sides

 Vent requirements

- Use vents with an opening rate of at least 70%

- Opening rate (%) =

B

d

c

    .   ℎ

  

Air vent area

16

A

LED R&D Lab(VD)

1. Product Information and Installation Precautions

 Minimum spacing for wall mounting installation

Min condition : 30mm (set ~ ceiling)
Recommended condition : more than 500mm

Air vent area

Air vent area

WALL

(more than 60%
of opening rate)

Min condition: 30mm (set ~ floor)
Recommended condition : more than 500mm

17

Air vent area
(more than 60%
of opening rate)

LED R&D Lab(VD)

1. Product Information and Installation Precautions

 Minimum spacing for processed installation

Min condition : 0mm (set ~ ceiling)
Recommended condition : more than 500mm

Essential cond. : more than 30mm of 100% opening rate

WALL

Essential cond. : more than 30mm of 100% opening rate

Min condition: 0mm (set ~ floor)
Recommended condition : more than 500mm

Air vent area

Air vent area

18

LED R&D Lab(VD)

1. Product Information and Installation Precautions

 Example of minimum spacing and FAN allocation for wall mounting installation

Min condition : 30mm (set ~ ceiling)
Recommended condition : more than 500mm

Other parts except for FAN

area should be sealed

left and right should be sealed

WALL

left and right sealing

Air vent area should be mesh type with
an opening rate of more than 60%.

Min condition: 30mm (set ~ floor)
Recommended condition : more than 500mm

19

LED R&D Lab(VD)

1. Product Information and Installation Precautions

 Example of minimum spacing and fan allocation for recessed installation

Min condition: 0mm (set ~ ceiling)
Recommended condition : 500mm

Essential cond. : more than 30mm of 100% opening rate

Other parts except

for FAN area should

be sealed

WALL

Essential cond. : more than 30mm of 100% opening rate

Min condition: 0mm (set ~ floor)
Recommended condition : 500mm

left and right should be sealed.

※ Vent and interior finishing work will proceed after screen installation.

20

Air vent area

LED R&D Lab(VD)

1. Product Information and Installation Precautions

 Example of minimum spacing and placement during rear exhaust

Ambient temperature on the back of

the wall should be less than 30 ℃.

Other parts except for
FAN should be sealed.

WALL

left and right should be sealed.

Essential cond. : more than 30mm of 100% opening rate.

21

Air vent area

LED R&D Lab(VD)

1. Product Information and Installation Precautions

◆ Preparation for installation

Electric screwdriver

Service JIG

(BH81-00001A)

Phillips (+)

※ Recommended sizes

Holder Magnet Tool

(Included in LED MODULE JIG)

screwdriver

22

LED MODULE JIG

(model name: CY-LJRNLS)

Pliers

Anti-static

gloves

LED R&D Lab(VD)

1. Product Information and Installation Precautions

◆ IER (IFR) Accessory configuration

Common

Quick Setup Guide

Extension Power Cable OCM Cable

COVER PCB

(IER : 7ea / IER-F : 4ea)

Product Warranty Card

(Not provided in some regions)

Power Cord

regulation guide

PET Tape (W10*L540,1 EA)

Machine Screws

(IER : 7ea / IER-F : 13ea)

IER / IFR

(guide pin,2ea)

IER-F / IFR-F

COVER PCB (6ea)

BRACKET LINK (2ea)

STUD PEM

BRACKET ALIGN (1ea)

23

LED R&D Lab(VD)

2. Preparation for Cabinet Installation

◆ Preparation for installation

① Remove the tape on top of the package box and open the box. (See Fig.1.)
② Remove the Top–Cushion and open the shielding bag.

Hold the handles inside, take out the set, and then remove the PE bag. (See Fig.2.)

③ Check that the sliding bolts are properly fastened. (See Fig.3.)

■ IER

■ IER- F

Fig.1 Contents of the

package

Bottom­Cushion

Box

LED
set

IB &
cable

Top­Cushio
n

IB & cable

Fig. 2 Opening the

Bottom-Cushion

Fig.3 Checking the bolts

package

SLIDING BOLT

handl

e

Handle Shape

SLIDING
BOLT

Box

Top-Cushion

LED set

24

LED R&D Lab(VD)

2. Preparation for Cabinet Installation

◆ Preparation for installation

④ Connect the power and check for a problem with the screen. (See Fig.4.)

※ See page 12 for details on how to check for a screen problem.

⑤ Guide Pin (Accessory Enclosed) 2EA is assembled on top of the cabinet. (Excluding the capinet on the top row)
⑥Unfasten the screws (four screws in total) and remove the corner covers. (See Fig.5.)

※ IER / IFR

※ IER- F / IFR-F

Fig.4 Checking the screen Fig.6 Removing the corner covers

Switch Button

Fig.5 Guide Pin Assembly

Guide
Pin

SCREW

Switch Button

25

SCREW

LED R&D Lab(VD)

2. Preparation for Cabinet Installation

◆ Note: Checking for a screen problem

⑥ Connect the power cord that came with the product and turn on the product.

Check that there is no LED damage and no problem is found on the screen.

Power In

Switch (Toggle)

Power out

※ Steps to perform in the event of White Pattern

- Apply power and press and hold the Switch for 5 seconds.

- When the factory info window appears, press the Switch once again.

- When the color screen appears, press the Switch repeatedly to check for malfunctioning LEDs.

(Each time the Switch is pressed, the LED color is switched in the following order:

white → blue → red → green.)

- To turn off the mode, press and hold the Switch for 5 seconds again.

26

LED R&D Lab(VD)

2. Preparation for Cabinet Installation

⑧ For cabinets placed on the edge, attach PET sheet before attaching PCB covers.

※ Attach PET sheet to all borders of the LED module (Fig.1), and attach PCB covers to the same outer sides where the

PET sheet has been attached (horizontally 5 points and vertically 4 points, as shown by the blue borders in Fig.2).

※ Attach PET sheet as shown in Fig.3. Make sure the area with no tape guides the LED module.

※ Attach PCB covers as shown in Fig.4.

No tape

0 to 0.5 mm

Fig.1 Attach PET sheet here

PET sheet

Fig.3

Fig.2 Borders requiring PET sheet and PCB covers

* Numeric figure: Quantity of PCB covers to attach

27

Fig.4

Fig.1 Attach PET sheet here

LED R&D Lab(VD)

3. Frame kit Components

① Check the configuration below in the frame kit.

※ Refer to the attached specifications for the IER-F/IFR-F installation.

No. Item

ⓐ

ⓑ

ⓒ

ⓓ

ⓔ

ⓕ

ⓖ

ASSY BRACKET SIDE

ASSY BRACKET MIDDLE

ASSY BRACKET CENTER

ASSY BRACKET JIG

JOINT V

ASSY ANCHOR SCREW

QUICK INSTALL GUIDE

ⓗ

ⓘ

Service JIG

Wrench

VG-

LFR84FWL

8X4 5X3 5X2 1X1 PIVOT

2 2 2 2 2

6 3 3 - 3

1 (+1) 1 (+1) 1 (+1) - 1 (+1)

2 2 2 - 1

10 7 7 2 7

50 28 21 4 14

1 1 1 1 1

1 1 1 - -

1 1 1 1 1

VG-

LFR53FWL

VG-

LFR52SWL

Qty (+spares)

VG-

LFR11SWL

VG-

LFR51PWL

a

e

JOINT V

b

d

f

M5,L65, Anchor screw

b

c

b

g

QSG

a

h

SERVICE JIG

WASHER (SLIDING BOLT)

ⓙ

ⓚ

ⓛ

Screen size for installation (mm)

BOLT – ETC

SCREW (M4)

10 5 5 - -

- - - - 12

20 14 14 4 14

7680 X

2160

4800 X

1620

4800 X

1080

960 X

540

28

2700 X

2880

i

WRENCH

j

WASHER

k

BOLT-ETC

SCREW (M4)

LED R&D Lab(VD)

l

4. Frame Installation

② On the left end, place the ⓐBracket Side and fasten the screws to install the Bracket (Fig.3).

※ Fasten one screw first, and use a clinometer to vertically align the right edges and fasten screws into the other holes.

(See the next page for precautions when fastening screws.)

Fasten the screws in the order of screw 1 → screw 2 → screw 3. Fig.1

ⓐ Fix the Bracket Side, following the measurements shown in Fig.4.

25 mm or above

①

③

③

Screwing
hole

②

Fig.2 Screwing hole

Fig.1 Order of fastening the screws

a

b

d

b

Fig.3 Positions of
components to attach

c

b

a

12 mm or above

a

12 mm or above

Fig.4 Screw fastening position
based on screen

29

LED R&D Lab(VD)