Page 1
Put TX(transmitter), RX (receiver)and managed switch hub on testing desk, see drawing-1:
Before installation, please read all silk screening of input and output ports on all 3 units(drawing-2).
XM200 SET-UP MANUAL
TX
RX
Drawing-3:
1、Connect a 6ft HDMI cable to TX Input
and DVD player.
2、Connect a 6ft HDMI cable to TX output
and Local TV.
3、Connect a 100M
Lan Cable to TX RJ45.
Φ3.5mm audio set-up：
a、Microphone to Line in.
b、Speaker to Line out.
Connecting TX to DVD or other
sources（drawing-3）
DC
POWER
SPEA
KER
MOBILE HDD
MICROPHONE
LAN CABLE
SOURES
LOCAL TV
drawing 2
drawing 1
TX
RX
Managed switch
3 1 2 a b
a
Page 2
MANY to MANY Set-up, (drawing-7,8,9,10)
DIP SWITCH
Installation of RX to
HDTV/Monitor(drawing-4)
DC POWER
LAN CABLE
TV
SPEAKER
MICROPHONE
Drawing-4:
4、Connect HDMI output of XM200 RX
and HDTV via one 6ft HDMI cable.
5、Connect RX RJ45 by a 100M Lan
Cable.
Φ3.5mm audio set-up：
c、Microphone to Line in.
d、Speaker to Line out.
drawing-5
ONE to ONE Set-up, drawing-5，
Adjust dip switch TX and RX to have the same positions on dip switch.
Green light of Link will turn on.
DIP SWITCH
USB PORT: KEY
BOARD, MOUSE,
HARD DISK
RS232 PORT:
COMPUTER
IR RECEIVER CABLE
IR
EMITTER
CABLE
IR RECEIVER CABLE
IR EMITTER CABLE
IR Pass through (drawing-6）：
6、Connect IR emitter cable to IR-RX of XM200 transmitter.
7、Connect IR Receiver cable to IR-TX of XM200 receiver.
8、DVD remote control to control DVD from TV end.
9、Vice versa, TV remote control at soures end to control TVs.
drawing-6
Drawing-7:
1、Connect a 6ft HDMI cable to TX input
and DVD player.
2、Connect any one port of 1G managed
switch and TX by a 100m Lan Cable.
3、Connect IR emitter cable to IR-RX of
XM200 transmitter, pointing to
sensor of DVD Player.
drawing-7
d c 4
5
6
7
1 2 3
Page 3
Connect TX and RX of XM200 to Switch.
Drawing-8:
4、Connect a 100m Lan Cable to any one
of ports of managed switch.
5、Connect RX of XM200 to TV by a 6ft
HDMI cable.
6、Connect IR receiver cable to IR-TX of
XM200 receiver, fix senser at a
proper position for a good remote
control.
drawing-8
Drawing-9: Connect other 100m Lan cables to TX and RX of XM200。
Don't Connect!
drawing-9
Drawing-10:
7、Make sure all connecting ports are in place.
8、All powers are hooked up.
9、Dip switch set-up ：
(1)、Adjust dip switch manually TX and RX of XM200 to make same positions.
or alternately:
(2)、Adjust TX and RX wtih same positions via RS232.
(3)、Connect a 6ft Lan cable to computer and managed switch to make same positions.
drawing-10
4 5 6
Page 4
ONE to MANY Set-up:
●Adjust dip switch to make TX and RX same positions. (see drawing-11,12,13)
Drawing-11:
1、Connect HDMI input of M200 TX to DVD Player by a 6ft HDMI cable.
2、Connect XM200 TX output to local HDTV via a 6ft HDMI cable.
3、Connect one 100m Lan cable to Managed switch.
drawing-11
Don't Connect
Drawing-12:
4、Connect 100m Lan cables to available RJ45 of managed
switch and RX of XM200.
5、Connect 100m Lan cables to the 2nd or more managed
switches, theoretically 65,000 RXs can be installed.
drawing-12
Drawing-13:
6、All connecting ports are in place
；
7、All powers are hooked up.
8、The set-ups are complete.
drawing-13
1 2 3
4
5
Page 5
Important:
1、
Managed switch requires IGMP, Jumbo Frames, Multi-ports, transmission speed 1G or up.
2、
Lan cable or Cat-5e or Cat-6 should be high speed, and shorter than 100meters.
3、
For 6ft HDMI cables connecting soures and TVs require 28AWG.
4、 Support resolutions ：480i/576i/720P/1080i/1080P.
6、
Power supply: DC5V/2A.
Loading...