Summit SPR7OSSTBC, SPR7OSSTBCADA USE & CARE

Write Model and Serial Numbers here:

Model _________________________
Serial No. ______________________

FELIX STORCH, INC.
Summit Appliance Division

An ISO 9001:2015 registered company
770 Garrison Avenue
Bronx, New York
www.summitappliance.com

BUILT-IN UNDERCOUNTER COMMERCIAL

OUTDOOR BEER DISPENSERS (KEGERATORS)

SPR7OSSTBC

SPR7OSSTBCADA

Instruction Manual

BEFORE USE, PLEASE READ AND FOLLOW

ALL SAFETY RULES AND OPERATING INSTRUCTIONS

NOTE: These units are designed for the cooling and dispensing

of beer only, and are not recommended for storing perishable
foods such as meats or dairy products.

IMPORTANT SAFEGUARDS

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.

This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can kill or
injure you and others. All safety messages will follow the Safety Alert Symbol and either the
words DANGER or WARNING.

DANGER means that failure to heed this safety statement
may result in severe personal injury or death.

WARNING means that failure to heed this safety statement
may result in extensive product damage, serious personal
injury, or death.

Safety messages will alert you to what the potential hazard is, tell you how to reduce the chance of injury, and let
you know what can happen if the instructions are not followed.

Before the kegerator is used, it must be properly positioned and installed as described in this
manual, so read the manual carefully. To reduce the risk of fire, electrical shock or injury when
using the appliance, follow basic precautions, including the following:

Plug into a grounded 3-prong outlet. Do not remove grounding prong, do not use an adapter, and do not use an

extension cord.

It is recommended that a separate circuit, serving only your kegerator, be provided. Use receptacles that cannot

be turned off by a switch or pull chain.

Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or explosion. And do

not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. The
fumes can create a fire hazard or explosion.

Before proceeding with cleaning and maintenance operations, make sure the power line of the unit is

disconnected.
Do not connect or disconnect the electric plug when your hands are wet.
Unplug the appliance or disconnect the power before cleaning or servicing. Failure to do so can result in

electrical shock or death.
Do not attempt to repair or replace any part of your kegerator unless it is specifically recommended in this

material. All other servicing should be referred to a qualified technician.

Use two or more people to move and install the appliance. Failure to do so can result in back or other injury.
To ensure proper ventilation for your appliance, the front of the unit must be completely unobstructed. Choose a

well-ventilated area with temperatures above 60°F (16°C) and below 90°F (32°C).
The appliance should not be located next to ovens, radiators or other sources of high heat.
The appliance must be installed with all electrical connections in accordance with state and local codes. A

standard electrical supply (115V AC only, 60 Hz), properly grounded in accordance with the National Electrical

Code and local codes and ordinances, is required.
Do not kink or pinch the power supply cord of the appliance.
The fuse (or circuit breaker) size should be 15 amperes.
It is important for the kegerator to be leveled in order to work properly. You may need to make several

adjustments to level it.
Never allow children to operate, play with or crawl inside the kegerator.
Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may damage or discolor

the interior.
Do not use this apparatus for other than its intended purpose.

THESE MODELS ARE DESIGNED FOR COMMERCIAL USE AND MAY BE USED IN THE INDOORS OR
OUTDOORS.

Risk of child entrapment

Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators and freezers

are still dangerous, even if they will “just sit in the garage a few days.”

Before you throw away your old refrigerator or freezer: Take off the doors. Leave the shelves or

drawers in place so that children may not easily climb inside.

Never allow children to operate, play with, or crawl inside the refrigerator/freezer.

THIS APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM PERSONS UNLESS THEY
HAVE BEEN ADEQUATELY SUPERVISED BY A RESPONSIBLE PERSON TO ENSURE THAT THEY CAN USE
THE APPLIANCE SAFELY. YOUNG CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY DO NOT
PLAY WITH THE APPLIANCE.

– SAVE THESE INSTRUCTIONS –

Location of Parts

Temperature control dial
(thermostat) and interior
light

Stainless steel door

Front ventilation
slots (kick plate)

Leveling legs

Compressor
step

CO2 canister

holder

Twin taps

Railing

NOTE: Models with suffix “NK” do not include a tap kit

Technical Information

Model Numbers
and
Descriptions

SPR7OSSTBC Standard height
SPR7OSSTBCADA 32.25” high for ADA compliant counters

Capacity

Two 1/6 kegs

Electrical Input

115V AC/60Hz

Rated Current

1.3A

Defrost

Automatic

Refrigerant

R134a (1.8 oz.)*

Installation

Built-in or free-standing

Unit Dimensions
(W x D x H)

23.75" x 24.75" x 32” (32.25" to hinge cap)

NOTES: Models with “NK” in the suffix do not include tapping equipment.

All models are ETL-S listed to NSF-7 standards for commercial use.

Specifications are subject to change without notice.

Door swing cannot be reversed in the field.

CALIFORNIA CARB/SNAP DISCLOSURE For products manufactured after January, 1, 2019:

Retail food refrigeration equipment manufactured after January 1, 2019, designed to store and display chilled
goods for commercial sale, and that use HFC-134a/R134a refrigerant are not for sale in California.

This equipment is prohibited from use in California with any refrigerants on the 'List of Prohibited Substances' for
that specific end-use, in accordance with California Code of Regulations, title 17, section 95374. This disclosure
statement has been reviewed and approved by Felix Storch, Inc. and Felix Storch, Inc. attests, under penalty of
perjury, that these statements are true and accurate.

Installation Instructions

Parts List

Remove all packing materials and parts. Inspect to make sure all parts listed below are present
and in good condition:

1 double draft arm assembly (with washer)
1 CO2 cylinder
1 CO2 regulator
2 keg taps (American Sankey type)
1 cleaning kit
Vinyl tubing
1 stainless steel (removable) floor to protect the unit during keg insertion
1 drip tray
Hose clamps
Various screws

Before Using Your Appliance:

Remove the exterior and interior packing.
Before connecting the unit to a power source, let it stand for approximately 2 hours. This will reduce

the possibility of a malfunction in the cooling system from handling during transportation.

Clean the interior surfaces of the unit with lukewarm water using a soft cloth.

Installing the Kegerator:

Place the unit on a floor that is strong enough to support the appliance when it is fully loaded. To level

the unit, adjust the two leveling legs at the front.

Your appliance is designed to be either built-in or free-standing in indoor or outdoor settings. Take

care that the air vents at the front of the appliance are never covered or blocked in any way. For

optimum performance, it is recommended to keep ¼” space on each side and at the top, as well as 2”

in the back.

Locate the unit away from direct sunlight and sources of heat (oven, heater, radiator, etc.). Direct

sunlight may affect the acrylic coating and heat sources may increase electrical consumption.

Extremely cold ambient temperatures may also affect the unit's performance.

Avoid locating the unit in moist areas. Too much moisture in the air will cause frost to form quickly on

the evaporator, requiring more frequent defrosting of the interior.

Plug the unit into an exclusive, properly installed and grounded wall outlet. Do not under any

circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning

power and/or grounding should be directed toward a certified electrician or authorized service center.

Improper use of the grounded plug can result in the risk of electrical shock. If the power
cord is damaged, have it replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.

Electrical Connection:

This unit should be properly grounded for your safety. The power cord of this unit is equipped with a
three-prong plug which mates with a standard three-prong wall outlet to minimize the possibility of
electrical shock.

Do not under any circumstances cut or remove the third ground prong from the power cord supplied. For
personal safety, this appliance must be properly grounded.

This unit requires a standard 115-volt AC/60Hz electrical outlet with three-prong ground. Have the wall
outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. When a
standard 2-prong wall outlet is encountered, it is your responsibility and obligation to have it replaced
with a properly grounded 3-prong wall outlet.

To prevent accidental injury, the cord should be secured behind the unit and not left exposed or
dangling.

The unit should always be plugged into its own individual electrical outlet which has a voltage rating that
matches the rating label on the appliance. This provides the best performance and also prevents
overloading house wiring circuits that could cause a fire hazard from overheated wires. Never unplug the
unit by pulling on the power cord. Always grip the plug firmly and pull straight out from the receptacle.
Repair or replace immediately any power cord that has become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage along its length or at either end. When moving the
unit, be careful not to damage the power cord.

Extension Cord:

Do not use an extension cord with this appliance. If the power cord is too short, have a qualified
electrician or service technician install an outlet near the appliance.

Adjusting the Tilt

If your beer cooler seems unsteady or you would like the door to close more easily, you can use the
leveling legs to adjust the tilt of the unit.

Be sure that the unit is in its final position when making adjustments to the tilt and that it is plugged into
a grounded 3-prong outlet.

WARNING:

Two or more people are required to move and/or install the refrigerator. Failure

to do so may cause back or other injury.

Turning a leveling leg to the right will lower the appliance toward the position of the leg. Likewise,

turning to the left will raise the unit away from the leg.

Several turns of the leveling legs may be required before the tilt of the appliance is properly

adjusted.

Turning both front legs the same amount to the left will tilt the kegerator to the rear. This adjustment

makes it easier for the door to close.

NOTE: It is easier to adjust the leveling legs if someone else pushes against the top of the
appliance to take the weight off the legs.

Draft Arm Assembly

1. Slide the gasket over the wing nut on the bottom of draft arm assembly beer tubes. Slide gasket up
beer tubes to draft arm base.

2. Push the wing nut on the beer tube of the draft arm assembly through the hole in the top of the
cabinet until the draft arm is resting on cabinet top.

3. Align holes in draft arm base with holes in gasket and pilot holes in cabinet, then secure the guard rail
to the cabinet top.

Beer Kegs and Keg Tappers

Your kegerator cooler comes with a double tap and will accommodate two “Sixth Barrel” kegs, also

known as “sixtels” or “logs”. Each sixtel has a height of 23-3/8” and a diameter of 9-1/4”, and hold 5.16
gallons of beer. Two Cornelius (“Corny”) kegs will also fit. The unit will not hold a half barrel or quarter

barrel, although it can take one “Slim Quarter” barrel.
The Sankey type keg tappers supplied with the kegerator are the most widely used in the United

States.
However, other types of keg tappers can be used. Before installing a keg tapper, check with your beer
distributor to make sure that the Sankey type keg tapper can be used.

If you need keg tappers other than the Sankey type, it is recommended that you purchase the tappers
you need from your beer distributor. Please keep the Sankey type keg tappers for future use. The
Sankey system is becoming more popular. It may be purchased from our Sales Department at 718-893-

3900.

Leveling leg

CO2 Regulator and CO2 Cylinder

NOTE: Your CO2 cylinder is shipped empty to avoid any possible accidents during transportation. When

you purchase the first keg of beer, have your beer distributor fill the CO2 cylinder. You must read and
understand the following procedures for CO2 cylinders before installation:

1. Install the CO2 gas line tube to the regulator by attaching one end of the red tube to the hose

connection on the CO2 regulator.

2. Secure the tube by using one of the self-locking black plastic snap-on clamps.

3. Insert a special washer into the regulator-to-cylinder attachment nut.

4. Attach the CO2 regulator to the CO2 cylinder by screwing the regulator nut onto the cylinder valve and

tightening with an adjustable wrench.

5. Remove the bolt with the nut from the cylinder retainer. Using two screws, attach it inside the unit on

the left side of the back wall. Holes are pre-drilled and screws are included.

6. Slide the cylinder through the retainer and secure it with the bolt and the nut. Position the cylinder

this way so that you will be able to read the numbers on the gauges and easily access the shut-off
valve.

Installation of Accessories

1.

Once the unit has been positioned under the counter, install the beer tower assembly and the mixed
ball valve:

a.

Lower the beer tower through the hole in the counter and into the hole at the top of the beer
dispenser’s upper surface. Be sure the tap is facing toward the front of the machine.

b.

Take out the accessories of the mixed ball valve. Attach the transparent hose to the beer
outlet of the mixed ball valve. (See Figure 5).

2.

Install CO2 gas cylinder and CO2 regulator valve:

a.

Fix the two CO2 hose clamps on the red CO2 tube (See Figure 6).

b.

Connect the ends of the red CO2 tube respectively to the CO2 intake port of the mixed ball valve

and the round outlet of the CO2 regulator valve. Lock these connections firmly with the two
clamps on the red CO

2

tube (See Figure 7).

c.

Using the wrench, tighten the CO2 regulator table valve with the hex nut port to the gas outlet

of the CO

2

tank (See Figure 9).

d.

Place the CO2 tank and CO

2
regulator valve component
into the cabinet and fix the
CO2 tank with tank bracket
and retainer

(See Figure 8).

3. Install the beer keg:
Note: This unit can hold two one-sixth barrel kegs, but not a full-size keg.

Place the beer keg into the cabinet and firmly connect the keg’s opening to the
connection port of the mixed ball valve.

Note: To place a keg into the cabinet, use the keg handle to move the keg

to the front of the open beer dispenser, then carefully tip the keg so that
the raised bottom edge contacts the edge of the cabinet. Finally, lift the
keg handle to raise the keg to the level of the floor of the cabinet and
push the keg into place.

4.

Install tap handle and beer tap:

Screw the tap handle clockwise into the beer tap to make a firm connection. Then
connect the tap to the beer tower components and tighten with a wrench (See
Figure 9).

Notes:

When replacing the beer keg, first turn off the safety switch on the CO

2

regulator valve and remove the mixed ball valve to take out the keg.
When replacing the CO2 gas cylinder, remember to turn off the main switch

of the CO2 gas cylinder and the safety switch on the CO2 regulator valve.
Afterwards, use a wrench to loosen the hexagonal nut port connecting the
CO2 regulator valve with the CO2 tank. Then, using a wrench, remove the
fixed bolt of the CO2 tank to take out the CO2 tank.

During the installation process, be sure that all parts are connected
tightly and that there are no gas leaks.

When connecting the hose to the connection port, you can dip the ends
into warm water to make the connection easier.

If the high-pressure compressed gas in the CO2 tank is not handled properly,
it could be dangerous:

a.

Make a note of the D.O.T. testing date on the cylinder neck before
installation. If it is more than 5 years old, don’t use the product. Return it
to the gas supplier.

b.

Keep gas cylinder away from heat sources. Unused cylinders should be
placed upright in a cool, ventilated place (preferably at 70ᵒF).

A Note about Freestanding Installation

If you decide to install your beer cooler in a freestanding position (rather than built-in)

you will need to order a special kit, which includes a guard rail and a set of casters.
Call our Customer Help Line at 1-800-287-8799 weekdays between 8:30am and
5:00pm ET.

Operating Your Kegerator

Temperature Control:

Your appliance’s evaporator system is out of sight behind the interior rear wall.
The interior temperature is controlled with a thermostat knob

located inside the unit, towards the upper right-hand corner.
Turn the knob clockwise from the STOP (0) position toward
the higher numbers for colder temperatures. Higher settings
on the knob (higher numbers) mean lower temperatures
(colder) in the kegerator.

On the coldest settings, temperatures in some spots inside

the cabinet may drop below 32°F. Use higher thermostat settings only when required
or recommended. When the ambient temperature is normal, we recommend a
medium setting.

Changes in the ambient temperature affect the temperature inside the refrigerator so

choose an appropriate setting of the thermostat knob, depending on ambient
conditions.

In the STOP (0) position, the appliance does not operate (the cooling system is

switched off), yet the power supply is not interrupted (the light still works).

The temperature inside the kegerator also depends on how often you open the door.

NOTES: .

1. Interior lighting is controlled by a manually-operated rocker switch. To maintain the
proper interior temperature, keep the light on only as long as necessary.

2. If the kegerator is unplugged, has lost power, or is turned off, you must wait 3 to 5
minutes before restarting it. If you attempt to restart before this time delay, the unit will
not start.

Defrosting:

This appliance operates with an automatic defrost system, so it defrosts itself. While the
compressor is operating, ice will build along the rear cold wall (the evaporator plate is
behind the wall). During the compressor’s off-cycle, ice will melt, drip down, collect in the
trough at the bottom and drain through a small hole into a tray above the compressor;
where the compressor’s heat will evaporate the water. If you notice excessive ice build­up on the rear wall, try setting the thermostat to a slightly warmer setting; be sure that
the door gasket is sealing well and that there is no obstruction of the drain hole at the
bottom rear of the interior cabinet.

Care and Maintenance

Cleaning Your Appliance:

1. Unplug the appliance, turn the thermostat to STOP (0) and remove all contents,

including shelves.

2. Wash the inside surfaces with a solution of lukewarm water and vinegar. Wipe dry

with a clean, soft cloth.

3. Wash the outside cabinet with a solution of warm water and mild liquid detergent.

Rinse well and wipe dry with a clean soft cloth.

4. Wring excess water out of the sponge or cloth before cleaning the area of the

temperature control or any electrical parts.

5. From time to time, wipe the condenser on the rear wall with a soft

non-metallic brush or vacuum cleaner.

6. After you have cleaned the appliance, reconnect it to the power

supply, reset the thermostat and return all contents to their place.

CAUTION: Failure to unplug the unit could result in electrical shock or

personal injury.

Power Failure:

Most power failures are corrected within a few hours and should not affect the
temperature of your appliance if you minimize the number of times the door is opened. If
the power is going to be off for a longer period of time, you need to take the proper steps
to protect your chilled items.

Vacations:

During long absences, remove all contents. Unplug the appliance, clean it and leave the
door open slightly to avoid possible formation of condensation, mold or odors.

Moving Your Appliance:

1. Remove the contents.

2. Securely tape down anything loose inside your unit.

3. Turn the leveling legs up to the base to avoid damage.

4. Tape the door shut.

5. Be sure the appliance stays secure in the upright position during transportation.

Energy-Saving Tips:

The unit should be located in the coolest area of the room, away from heat-producing

appliances or heating ducts and out of direct sunlight.

Try not to open the door too often, especially when the weather is damp and hot.

Once you open the door, close it as soon as possible.

Occasionally check if the appliance is sufficiently ventilated (adequate air circulation

behind the appliance).

Set the thermostat from higher to lower settings as soon as possible (depending on

how loaded the appliance is, ambient temperature, etc.).

Before loading items into the unit, be sure they have cooled to ambient temperature.

Draft Beer Troubleshooting

Problem

Cause

Correction

Beer is cloudy: The
beer in the glass
appears hazy and not
clear.

Excessively low
temperatures may
cause hazy or
cloudy beer,
particularly when
the beer lies in the
cold coil for long
periods of time.
Drain a few ounces before drinking.

Raise the temperature setting of the unit.

Glasses may not
have been cleaned
properly.

Do not wash beer glasses together with
glasses that have contained milk or any other
fatty substance. An excessive amount of
germicide build-up may also leave a fatty film,

It is preferable to steam and sterilize glasses
where health laws permit.

Wash glasses thoroughly with a good
detergent to remove all fatty substances

Do not use soap.

Do not wipe the glasses dry. Permit glasses to
air-dry by placing them on a wire rack or
corrugated metal sheet.

Rinse the glasses in fresh cold water just before
serving beer. It is best to serve beer in a wet
glass.

Improper drawing
of beer into glass

Open the faucet quickly and completely; proper
foam should be a tight creamy head. The collar
on the average glass should be ¾" to 1" high.
Beer drawn without a head has the appearance
of being flat.

Not enough
pressure

Increase the pressure if beer runs too slowly.
The correct flow should fill a 10-oz glass in 4
seconds (approx. 8 oz of liquid). Check the
pressure source to determine whether there
are obstructions in the air line. Replace a
sluggish air source or the CO

2

regulator and
gauge. The tank pressure must always be
higher than the pressure used on the keg.
Always apply pressure to the keg before
drawing beer.

Beer has off taste:
Often bitter and bite-y;
sometimes completely
lacking flavor and zest.
It may also have an
oily or foul odor which
may carry an
unpleasant taste.

Improper
cleaning of the
tap

Brush and clean the tap properly. It
should be scoured using a detergent,
then rinsed clean.

Contaminated air
line

Beer tube should be examined. If
contaminated, it should be replaced.

Condensation is
forming on the tap.

It is normal to see
condensation
forming on the tap.
It is caused by a
difference in
temperature
between the cold
beer and the
surfaces of the tap
when beer is
flowing through the
line. Beer that is left
in the tap is not
cooled by the beer
dispenser.

After a period of non-use, a few ounces
should be drained before drinking.

General Troubleshooting

When using this appliance, you may come across some problems that in many cases
result from improper handling and can easily be eliminated.

TROUBLESHOOTING GUIDE

The appliance fails to operate after being connected to the power source.

Check whether the power supply is active and that the thermostat is not set to the

STOP (0) position.

The compressor is running continuously.

The door was opened frequently or it was left open too long.
The door is not properly closed (the door may sag, the gasket may be dirty or

damaged).
The power supply has been interrupted for a long period of time.
The appliance may have been overloaded with items above room temperature.
There may be inadequate ventilation of the compressor and condenser. (Assure

there is adequate air circulation behind the appliance and wipe the dust from the

condenser.)

Noise

Cooling in refrigeration appliances is enabled by the refrigerating system with a

compressor, which produces noise. How noisy the appliance is depends on where

it is placed, how it is used and how old the appliance is.

During the operation of the compressor, the noise of liquid is heard and when the

compressor is not operating, the refrigerant flow is heard. This is a normal

condition and has no influence whatsoever on the lifetime of the appliance.

After starting the appliance, the operation of the compressor and the refrigerant

flow may be louder. This does not mean that something is wrong. Gradually the

noise is reduced.

Sometimes a louder noise is heard, which is unusual for the appliance. This noise

is often a consequence of improper placement of the unit. (The unit should be

placed and leveled firmly on a solid base and it should not touch the wall or

cabinets standing next to it.)

For parts and accessory ordering,

troubleshooting and helpful hints, visit:

www.summitappliance.com/support

Limited Warranty

ONE-YEAR LIMITED WARRANTY

Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is
operated and maintained according to instructions attached to or furnished with the product, warrantor will pay
for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be
provided by a designated service company. Outside the 48 states, all parts are warranted for one year from
manufacturing defects. Plastic parts, shelves and cabinets are warranted to be manufactured to commercially
acceptable standards, and are not covered from damage during handling or breakage.

5-YEAR COMPRESSOR WARRANTY

1. The compressor is covered for 5 years.

2. Replacement does not include labor.

ITEMS WARRANTOR WILL NOT PAY FOR:

1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to
replace or repair fuses or to correct wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs or broken shelves. Consumable parts (such as
filters) are excluded from warranty coverage.

3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper
installation, installation not in accordance with electrical or plumbing codes, or use of products not
approved by warrantor.

4. Replacement parts or repair labor costs for units operated outside the United States.

5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

6. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not
installed in accordance with published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES – LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE
PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR.
WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY
FROM STATE TO STATE.

WARNING: This product can expose you to chemicals including Nickel
(Metallic) which is known to the State of California to cause cancer.

For more information go to www.P65Warnings.ca.gov

Note: Nickel is a component in all stainless steel and some other metallic compositions.

FELIX STORCH, INC.
770 Garrison Avenue
Bronx, NY 10474
Phone: [phone]
Fax: [phone]
www.summitappliance.com

Printed in the U.S.A.