Summit MB27G, MB13G, MB12B, MB26SS User Manual

COMPACT MINIBARS

MODELS.

MB12B HMB21B
MB13G HMB31G

MB26SS HMB62SS

MB27G HMB72G

INSTRUCTION MANUAL

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS.

Felix Storch, Inc.
An ISO 9001:2015 registered company
770 Garrison Avenue
Bronx, NY 10474
www.summitappliance.com

Write Serial Number (on lower left corner of
inside cabinet) here:

Serial No.: _______________________

2

APPLIANCE SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read
and obey all safety messages.

This is the Safety Alert Symbol. The symbol alerts you to potential hazards that
can kill or injure you and others. All safety messages will follow the Safety
Alert Symbol and either the word DANGER or WARNING.

DANGER means that failure to heed this safety
statement may result in severe personal injury or
death.

WARNING means that failure to heed this safety
statement may result in extensive product
damage, serious personal injury, or death.

All safety messages will alert you about the potential hazard, tell you how to reduce the chance of injury,
and let you know what can happen if the instructions are not followed.

IMPORTANT SAFEGUARDS

Before the appliance is used, it must be properly positioned and installed as
described in this manual, so read the manual carefully. To reduce the risk of fire,
electrical shock or injury when using the appliance, follow basic precautions,
including the following:

Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do

not use an extension cord.
Replace all panels before operating.
It is recommended that a separate circuit serving only your appliance be provided. Use receptacles that

cannot be turned off by a switch or pull chain.
Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or explosion.

And do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance. The fumes can create a fire hazard or explosion.
Do not connect or disconnect the electric plug when your hands are wet.
Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result in

electrical shock or death.
Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in

this manual. All other servicing should be referred to a qualified technician.
This appliance is CFC- and HFC-free and contains small quantities of Isobutane (R600a) which is

environmentally friendly, but flammable. It does not damage the ozone layer, nor does it increase the

greenhouse effect. Care must be taken during transportation and setting up of the appliance that no

3

parts of the cooling system are damaged. Leaking coolant can ignite and may damage the eyes.

In the event of any damage:

- Avoid open flames and anything that creates a spark,

- Disconnect from the power supply,

- Air the room in which the appliance is located for several minutes and

- Contact the Service Department for advice.

The more coolant there is in an appliance, the larger the room it should be installed in. In the event of a

leakage, if the appliance is in a small room, there is the danger of combustible gases building up. For
every ounce of coolant, at least 325 cubic feet of room space is required. The amount of coolant in the
appliance is stated on the data plate inside the appliance. It is hazardous for anyone other than an
Authorized Service Person to carry out servicing or repairs to this appliance.

Take serious care when handling, moving and using the appliance to avoid either damaging the

refrigerant tubing or increasing the risk of a leak.

Replacing component parts and servicing shall be done by factory authorized service personnel, so as

to minimize the risk of possible ignition due to incorrect parts or improper service.

FOLLOW WARNING CALLOUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL

Before placing the appliance in a cabinet structure, ensure the ventilation openings is clear of

obstruction.
Choose a well-ventilated area with temperatures above 44°F (7°C) and below 90°F (32°C).
The appliance should not be located next to ovens, grills or other sources of high heat.
The appliance must be installed with all electrical, water and drain connections in accordance with state

and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly grounded in accordance

with the National Electrical Code and local codes and ordinances, is required.
Do not kink or pinch the power supply cord of the appliance.
The size of the fuse (or circuit breaker) should be 15 amperes.
It is important that the appliance be leveled in order to work properly. You may need to make several

adjustments to level it.
All installations must be in accordance with local plumbing code requirements.
Make certain that the pipes are not pinched, kinked or damaged during installation.
Check for leaks after connection.
Never allow children to operate, play with or crawl inside the appliance.
Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may damage or

discolor the interior.
Use this appliance only for its intended purpose as described in this Instruction Manual.
Keep fingers out of the “pinch point” areas. Clearances between the door and cabinet are necessarily

small. Be careful closing the door when children are in the area.

Risk of child entrapment!

Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are

still dangerous, even if they will “just sit for a few days”.

Before discarding your old refrigerator:

Take off the doors
Leave the shelves in place so that children may not easily climb inside.

- SAVE THESE INSTRUCTIONS -

4

INSTALLATION INSTRUCTIONS

BEFORE USING YOUR APPLIANCE

Remove the exterior and interior packing.
Before connecting the appliance to the power source, let it stand upright for approximately 2 hours. This

will reduce the possibility of a malfunction in the cooling system from handling during transportation.

Clean the interior surface with lukewarm water using a soft cloth.

INSTALLATION OF YOUR APPLIANCE

The appliance is designed for freestanding use.
CAUTION: This appliance is not designed for the storage of medicine or other medical products.
Place your appliance on a surface that is strong enough to support it when it is fully loaded.
For optimum performance, ensure there is 5” (127mm) of space between the back and sides of the unit,

and 4” (102mm) at the top, to allow proper air circulation to cool the compressor and condenser. Take
care that the air vent is never covered or blocked in any way.

NOTE: It is recommended that you do not install the appliance near an oven, radiator or other heating

source. Direct sunlight may affect the acrylic coating and heat sources may increase electrical
consumption. Don’t install in a location where the temperature will fall below 44°F (7°C). For best

performance, do not install the appliance behind a cabinet door or block the base grille.
Avoid locating the unit in moist areas.
Plug the appliance into an exclusive, properly grounded wall outlet.

ELECTRICAL CONNECTION

This appliance should be properly grounded for your safety. The power cord of this appliance is equipped
with a three-prong plug which mates with standard three-prong wall outlets to minimize the possibility of
electrical shock.

Do not under any circumstances cut or remove the third (ground) prong from the power cord supplied. For
personal safety, this appliance must be properly grounded. Any questions concerning power and/or
grounding should be directed toward a certified electrician or an authorized service center.

This appliance requires a standard 115/120 Volt AC ~60Hz three-prong grounded electrical outlet. Have
the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.

To prevent accidental injury, the cord should be secured behind the appliance and not left exposed or
dangling.

WARNING

Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is
damaged, have it replaced by a qualified electrician or an authorized service center.

5

The appliance should always be plugged into its own individual electrical outlet which has a voltage rating
that matches the rating label on the appliance. This provides the best performance and also prevents
overloading house wiring circuits that could cause a fire hazard from overheating. Never unplug the
appliance by pulling on the power cord. Always grip the plug firmly and pull straight out from the receptacle.
Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use
a cord that shows cracks or abrasion damage along its length or at either end. When moving the appliance,
be careful not to damage the power cord.

EXTENSION CORD

Because of potential safety hazards under certain conditions, it is strongly recommended that you do not
use an extension cord with this appliance. However, if you must use an extension cord, it is absolutely
necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord having a grounding
type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes.

REVERSING THE DOOR SWING OF YOUR APPLIANCE

If you find the direction of opening the door of the appliance inconvenient, you can change it. Holes on the
opposite side have already been prepared at the factory. To reverse your door, follow these instructions:

1. Unscrew the top 2 screws and bottom 3 screws of the existing hinge and put aside

2. Remove the top and bottom hinges

3. Use the same screws and hinges to reattached the door so it opens from the other side

OPERATING YOUR APPLIANCE

It is recommended you install the appliance in a place where the ambient temperature is between 44º and
82ºF (7º to 28ºC). If the ambient temperature is above or below the recommended temperatures, the
performance of the unit may be affected. For example, placing your unit in extremely cold or hot conditions
may cause interior temperatures to fluctuate. The operating temperature range may not be reached.

CONTROL PANEL

The control panel includes a display that shows the current interior air temperature of the minibar. To change

the display between Fahrenheit and Celsius, hold the button for five seconds.

To adjust the temperature, simply press the and buttons. When you press either button, the
temperature level (1 to 6) will flicker. Press to raise the unit to a warmer temperature (level 1 is the

warmest setting). To lower the temperature to a colder setting, press (6 is the coldest setting).
This unit will self-defrost for a period of 20 minutes every 24 hours.

Note: In the event that the temperature probe is not able to detect the temperature or is faulty, the screen

will display “F. ”

SHELVES

To prevent damaging the door gasket, make sure to have the door all the way open when pulling the
shelves out of the rail compartment.

6

Any of the shelves can be removed to store larger items.
When removing the shelf from the rail compartment, make

sure to remove all items first. Then move the shelf to the
position where the notch of the shelf is exactly under the
plastic post and lift the shelf. In order to replace the shelf,
repeat steps described above in reverse.

CARE & MAINTENANCE

CLEANING YOUR APPLIANCE

Turn off the power, unplug the appliance, and remove all items, including shelves.
Wash the inside surfaces with a solution of warm water and baking soda (about 2 tablespoons of baking

soda to a quart of water).
Wash the shelves with a mild detergent solution.
Wring excess water out of the sponge or cloth when cleaning the area where the controls are located,

or any electrical parts.
Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with a

clean soft cloth.

CAUTION:

Failure to unplug the appliance during cleaning could result in electrical shock or other personal injury

.

POWER FAILURE

Most power failures are corrected within a few hours and should not affect the temperature of your appliance
if you minimize the number of times the door is opened. If the power is going to be off for a longer period
of time, you need to take the proper steps to protect the contents.

MOVING YOUR APPLIANCE

1. Remove all items.

2. Securely tape down all loose items (shelves) inside your appliance.

3. Turn the adjustable legs up to the base to avoid damage.

4. Tape the door shut.

5. Be sure the appliance stays secure in the upright position during transportation. Also, protect the
outside of the appliance with a blanket or similar item.

ENERGY-SAVING TIPS

▪ The appliance should be located in the coolest area of the room, away from heat-producing

appliances and out of direct sunlight.

▪ Ensure that the unit is adequately ventilated. Never cover air vents.
▪ Do not keep the door open any longer than necessary.
▪ Let hot foods cool to room temperature before placing in the unit. Overloading the unit forces the

compressor to run longer.

▪ Be sure to wrap foods properly, and wipe containers dry before placing them in the unit. This cuts

down on frost build-up inside the unit.

▪ Unit shelves and storage bins should not be lined with aluminum foil, wax paper, or paper toweling.

Liners interfere with cold air circulation, making the unit less efficient.

▪ Organize and label food to reduce door openings and extended searches. Remove as many items

as needed at one time, and close the door as soon as possible.

7

Troubleshooting Guide

You can solve many common problems easily, saving you the cost of a possible service call. Try the
suggestions below to see if you can solve the problem before calling the servicer.

PROBLEM

POSSIBLE CAUSE

REMEDY

Appliance
does not
operate.

Appliance is not connected to a power

supply.
The appliance is turned off.
Tripped circuit breaker or a blown fuse.

Connect the appliance.
Switch on the appliance.

Switch on circuit breaker or replace

fuse.

Appliance is
not cold
enough.

The temperature is not set correctly.
The ambient temperature could require

a lower temperature setting.
The door was opened too often.

The door was not closed completely.
Door is not properly sealed.

The condenser is too dirty.
The ventilation opening is blocked or too

dusty, or not enough ventilation is

provided.

Check the set temperature.
Set a lower temperature.

Do not open the door more often than

necessary.
Close door properly.
Check the door seal and clean or

replace.
Clean the condenser when

necessary.
Clear the obstructions and clean off

the dust.

Appliance
turns itself on
and off
frequently.

The room temperature is higher than

average.
A large amount of food has been added

to the unit.
The door is open too often.
The door is not closed completely.

The door gasket does not seal properly.

Put the appliance in a cooler place.
Leave the appliance to work for a

while until the set temperature has

been reached.
Do not open the door more often than

necessary.
Close door properly.
Check the door seal and clean or

replace.

Vibrations

The appliance is not properly leveled.

Level the appliance with the

adjustable feet.

The appliance
seems to
make too
much noise.

The rattling noise may come from the flow of the refrigerant, which is normal. As each
cycle ends, you may hear gurgling sounds caused by the flow of refrigerant in your
appliance.
If temperature fluctuations occur, the contraction and expansion of the inner walls
may cause popping and crackling noises.

The appliance is not properly level.

Level the appliance with the

adjustable feet.

The door will
not close
properly.

The appliance is not properly level.
The door was reversed and not

properly installed.
The gasket is dirty.
The shelves are out of position.

Level the appliance with the

adjustable feet.
Check the door hinge and

reassemble correctly.
Clean the door gasket.
Check the shelves and refit correctly.

If you've checked the table above and find that you still need help with your appliance, call our Customer
Service facility at 800-932-4267 between 9:00AM and 5:00PM ET. We will do our best to answer your
quest

8

LIMITED WARRANTY

ONE-YEAR LIMITED WARRANTY

Within the 48 contiguous United States, for one year from the date of purchase, when this
appliance is operated and maintained according to instructions attached to or furnished with the
product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials
or workmanship. Service must be provided by a designated service company. Outside the 48
states, all parts are warranted for one year from manufacturing defects. Plastic parts, shelves and
cabinets are warranted to be manufactured to commercially acceptable standards, and are not
covered from damage during handling or breakage.

5-YEARS COMPRESSOR WARRANTY

1. The compressor is covered for 5 years.

2. Replacement does not include labor.

ITEMS WARRANTOR WILL NOT PAY FOR:

1. Service calls to correct the installation of your appliance, to instruct you how to use your
appliance, to replace or repair fuses or to correct wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs or broken shelves. Consumable parts
(such as filters) are excluded from warranty coverage.

3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper
installation, installation not in accordance with electrical or plumbing codes, or use of products
not approved by warrantor.

4. Replacement parts or repair labor costs for units operated outside the United States.

5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

6. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is
not installed in accordance with published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES – LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE
PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR. WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE
EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM
STATE TO STATE.

WARNING: This product can expose you to chemicals including Nickel
(Metallic) which is known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov

Note: Nickel is a component in all stainless steel and some other metal components.

FELIX STORCH, INC.
770 Garrison Avenue
Bronx, NY 10474
Phone: [phone]
Fax: [phone]
www.summitappliance.com

For parts and accessory ordering,

troubleshooting and helpful hints, visit:

www.summitappliance.com/support

Printed in China