Summit FS603SSVHFROST Use & Care

INSTRUCTION MANUAL FOR MODELS:

FS603FROST

Thank you for putting your trust in our company and for purchasing this appliance. We
hope it will successfully serve its purpose for many years.

The FS603FROST is a front opening freezer that maintains a -24 F temperature. The
open shelves and in-door storage system hold over 100 cans of beer.

Felix Storch, Inc.

Summit Appliance Division

770 Garrison Avenu e

www.summitappliance.com

Bronx, NY 10474

All-Freezer

Before Putting Into Use

Before connecting the beer froster to the power supply, leave it standing for about

24 hours. This will reduce the possibility of malfunctions in the cooling system
due to transport handling.

Clean the beer froster thoroughly; especially in the interior (See Cleaning and

Maintenance).

We Care for the Environment

Our appliances are distributed in packaging made of environmental friendly

material which could safely be recycled, disposed of or destroyed without any
effects on the environment whatsoever.

Our instruction manuals are printed either on recycled paper or chlorine free

bleached paper.

Tips for Energy Savings

Once you open the door try to close it as soon as possible.
Every now and then check if the beer froster is sufficiently ventilated
with adequate space behind the unit.

The coils on the rear of the beer froster should be cleaned and free

of dust or any other impurities.

Ice and frost layer increase energy consumption, so do clean the

appliance as soon as the layer is 1/8” thick.

Always consider instructions stated in sections Positioning and

Energy Saving Tips, otherwise the energy consumption is
substantially higher.

Instructions for Use

Important

To reduce the risk of fire, electrical shock,

! or injury when using your appliance,

follow these basic precautions.

Warning

Disposing of the Worn Out Appliance

Read all instructions before using the appliance
The appliance must be correctly connected to the power supply.
Disconnect the appliance from the power supply before repairing and/or

cleaning it (only a qualified technician should repair it).

Use only enclosed tools or tools recommended by the manufacturer.
For the sake of environmental protection be careful not to damage the rear

wall of the appliance (the condenser unit or the tubes when moving the
refrigerator) or any part of the freezing system inside the appliance. Use
only enclosed tools or tools recommended by the manufacturer.

DANGER: Risk of child entrapment.
Before throwing away your old beer froster please remove the doors and

leave the shelves in place so that children may not easily climb inside.

The rating plate is inside the appliance or outside on the rear wall.

When your beer froster finally wears out, dispose of it.
Remove the door in order to prevent child entrapment.

Instructions for Use

Placing and Installation

Class

Ambient Temperature

SN (sub-normal)

from + 56°F to + 90°F

N (normal)

from + 62°F to + 90°F

ST (sub-tropical)

from + 64°F to +100°F

T (tropical)

from + 64°F to +120°F

Choosing the Right Place

Place the beer froster in a dry and regularly ventilated room. Allowed ambient
temperature depends on the model (class) of the appliance and is stated on the

Never place the beer froster near heat emitting devices (e.g. cooker, radiator)
Do not place the beer froster in direct sunlight.
The appliance should be positioned at least 1 ½” away from a electric or gas
cooker and at least 12” away from a oil or coal stove. If this isn’t possible use
an appropriate insulation. Behind the beer froster there should be free space of

“DO NOT USE AN EXTENSION CORD.”
Required nominal voltage (120 volts) and frequency (60 Hertz) are indicated on
the rating plate.

rating plate of the appliance.

The beer froster may be exposed to lower or higher temperatures but only for
shorter period of time and the temperature should never be lower than 41°F.

at least 30 sq. in. and above there should at least 1 ½” in order to assure adequate
ventilation of the condenser unit.

Placing the Self-Standing Appliance

It is important to make sure the beer froster is leveled evenly to prevent falling.
Two spacers attached to the beer froster must be fitted onto the upper edge of the

condenser, thus preventing the appliance from being installed too close to the
wall. Spacers are manufactured for all-purpose functions depending on the
distance of the condenser from the wall. Therefore turn the spacers
correspondingly and adjust them accordingly.

Connection to Power Supply

Connect the beer froster using the 3 prong plug to the grounded power supply
outlet.

The connection to the power supply and grounding has to be made according to
current standards and regulations. The appliance resists temporary voltage
tolerance up to -15 to 10%.

Instructions for Use