Page 1
Felix Storch, Inc.
An ISO 9001:2015 registered company
770 Garrison Avenue
Bronx, NY 10474
www.summitappliance.com
Write Serial Number (on lower left outside of
FROST-FREE DRAWER REFRIGERATORS
Model Nos. FF1DSS / FF1DSS24 / FF12DROS / HDR13SS
SDR24 / SDR241OS / DR124SS
SDR30 / SDR301OS / DR130SS
SDR36 / SDR361OS / DR136SS
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS.
drawer) here:
Serial No.: _______________________
User Manual
Page 2
TABLE OF CONTENTS
Appliance Safety 3
Important Safeguards 3-4
Location of Parts 5
Installation Instructions 6-9
Before Using your Appliance 6
Installation of your Appliance 6
Electrical Connection 6-7
Extension Cord 7
Installing the Stainless Steel Handle 7
Installing the Anti-tip Brackets 8
Full Overlay Panel Installation Instructions 8-9
Operating your Appliance 10-12
Control Panel 10-11
Interior Light 11
Sabbath Mode 11
Temperature Memory Function 11
Defrosting 11
Temperature Alarm/Door Alarm 12
Care and Maintenance 13
Cleaning your Appliance 13
Power Failure 13
Vacation Time 13
Moving your Appliance 13
Energy-Saving Tips 13
Troubleshooting 14-15
Limited Warranty 16
2
Page 3
APPLIANCE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read
and obey all safety messages.
This is the Safety Alert Symbol. The symbol alerts you to potential hazards that
can kill or injure you and others. All safety messages will follow the Safety
Alert Symbol and either the word DANGER or WARNING.
DANGER means that failure to heed this safety
statement may result in severe personal injury or
death.
WARNING means that failure to heed this safety
statement may result in extensive product
damage, serious personal injury, or death.
All safety messages will alert you about the potential hazard, tell you how to reduce the chance of injury,
and let you know what can happen if the instructions are not followed.
IMPORTANT SAFEGUARDS
Before the appliance is used, it must be properly positioned and installed as
described in this manual, so read the manual carefully. To reduce the risk of fire,
electrical shock or injury when using the appliance, follow basic precautions,
including the following:
Plug into a grounded 3-prong outlet, do not remove the grounding prong, do not use an adapter, and
do not use an extension cord.
Replace all panels before operating.
It is recommended that a separate circuit serving only your appliance be provided. Use receptacles
that cannot be turned off by a switch or pull chain.
Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or
explosion. And do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance. The fumes can create a fire hazard or explosion.
Do not connect or disconnect the electric plug when your hands are wet.
Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result in
electrical shock or death.
Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in
this manual. All other servicing should be referred to a qualified technician.
This appliance is CFC- and HFC-free and contains small quantities of Isobutane (R600a) which is
environmentally friendly, but flammable. It does not damage the ozone layer, nor does it increase the
greenhouse effect. Care must be taken during transportation and setting up of the appliance so that
no parts of the cooling system are damaged. Leaking coolant can ignite and may damage the eyes.
3
Page 4
In the event of any damage:
– Avoid open flames and anything that creates a spark,
– Disconnect from the power source,
– Air the room in which the appliance is located for several minutes, and
– Contact the Service Department for advice.
The more coolant there is in an appliance, the larger the room in which it should be installed. In the
event of a leakage, if the appliance is in a small room, there is the danger of combustible gases building
up. For every ounce of coolant, at least 325 cubic feet of room space is required. The amount of coolant
in the appliance is stated on the data plate inside the appliance. It is hazardous for anyone other than
an Authorized Service Person to carry out servicing or repairs to this appliance.
Take serious care when handling, moving, and using the appliance to avoid either damaging the
refrigerant tubing or increasing the risk of a leak.
Parts replacements and servicing shall be done by factory-authorized service personnel to minimize the
risk of ignition due to incorrect parts or improper service.
FOLLOW WARNING CALLOUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL
Use two or more people to move and install the appliance. Failure to do so can result in back or other
injuries.
To ensure proper ventilation for your appliance, the front of the unit must be completely unobstructed.
Choose a well-ventilated area with temperatures above 44°F (7°C) and below 100°F (38°C).
The appliance should not be located next to ovens, grills, or other sources of high heat.
The appliance must be installed with all electrical, water, and drain connections in accordance with
state and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly grounded in
accordance with the National Electrical Code and local codes and ordinances, is required.
Do not kink or pinch the power supply cord of the appliance.
The size of the fuse (or circuit breaker) should be 15 amperes.
It is important that the appliance be leveled for it to work properly. You may need to make several
adjustments to level it.
All installations must be in accordance with local plumbing code requirements.
Make certain that the pipes are not pinched, kinked, or damaged during installation.
Check for leaks after connection.
Never allow children to operate, play with or crawl inside the appliance.
Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may damage
or discolor the interior.
Use this appliance only for its intended purpose as described in this Instruction Manual.
Keep fingers out of the “pinch point” areas. Clearances between the drawers and cabinet are
necessarily small. Be careful closing drawers when children are in the area.
Risk of child entrapment!
Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are
still dangerous, even if they will “just sit for a few days.”
Before discarding your old appliance:
Take off the doors
Leave the shelves in place so that children may not easily climb inside.
- SAVE THESE INSTRUCTIONS -
4
Page 5
LOCATION OF PARTS
Handle
Control Panel
Drawer
Adjustable Legs
5
Page 6
INSTALLATION INSTRUCTIONS
damaged, have it replaced by a qualified electrician or an authorized service center.
Before Using your Appliance
Remove the exterior and interior packing.
Before connecting the appliance to the power source, let it stand upright for approximately 2 hours.
This will reduce the possibility of a malfunction in the cooling system from handling during
transportation.
Clean the interior surface with lukewarm water using a soft cloth.
Install the handles on the drawer if they are not already attached. (See page 7.)
Installation of your Appliance
The appliance is designed for built-in or recessed or free-standing installation for indoor or
outdoor use.
CAUTION: This appliance is not designed for the storage of medicine or other medical products.
Place your appliance on a floor that is strong enough to support it when it is fully loaded. To level
the unit, adjust the front leveling legs.
For free-standing installation, 5” (127mm) of space between the back and sides of the unit, and 4”
(102mm) at the top, are suggested. This allows the proper air circulation to cool the compressor
and condenser. Even for built-in installation, it is necessary to keep ¼” (6.35mm) space on each
side and at the top and 2” (51mm) at the rear. Take care that the air vent at the front of the
appliance is never covered or blocked in any way.
NOTE: It is recommended that you do not install the appliance near an oven, radiator, or other
heating sources. Direct sunlight may affect the outer coating and heat sources may increase
electrical consumption. Do not install in a location where the temperature will fall below 44°F
(7°C). For best performance, do not install the appliance behind a cabinet door or block the
base grille.
Avoid locating the unit in moist areas.
Plug the appliance into an exclusive, properly grounded wall outlet.
Electrical Connection
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is
This appliance should be properly grounded for your safety. The power cord of this appliance is
equipped with a three-prong plug that fits into a standard three-prong wall outlet to minimize the
possibility of electrical shock.
Do not, under any circumstances cut or remove the third (ground) prong from the power cord
supplied. For personal safety, this appliance must be properly grounded. Any questions concerning
power and/or grounding should be directed toward a certified electrician or an authorized service
center.
WARNING
6
Page 7
This appliance requires a standard 115/120 Volt AC ~ 60Hz three-prong grounded electrical outlet.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly
grounded. When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation
to have it replaced with a properly grounded 3-prong wall outlet.
To prevent accidental injury, the cord should be secured behind the appliance and not left exposed
or dangling.
The appliance should always be plugged into its own individual electrical outlet which has a voltage
rating that matches the rating label on the appliance. This provides the best performance and
prevents overloading house wiring circuits that could cause a fire hazard from overheating. Never
unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull it straight out
from the receptacle. Repair or replace immediately all power cords that have become frayed or
otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at
either end. When moving the appliance, be careful not to damage the power cord.
Extension Cord
Because of potential safety hazards under certain conditions, it is strongly recommended that you do
not use an extension cord with this appliance. However, if you must use an extension cord, it is
absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord
having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at
least 10 amperes.
Installing the Stainless Steel Handle
This appliance includes a stainless steel handle
that is not required to operate the unit. To install the
handle, follow the instructions below:
1. Remove the door gasket.
2. Install the handle with the screws provided. (DO
NOT over-tighten as this will cause damage to the
stainless steel door surface.)
3. Replace the door gasket.
7
Page 8
Anti-tip
Bracket
Screw
Anti-tip
Bracket
Screw
1 2 3
4 5
6
7
Installing the Anti-Tip Brackets
Included with this unit is a pair of anti-tip brackets to
help prevent the unit from moving inside the
countertop when opening the drawer.
Place the provided brackets in front of the unit’s
ventilation grille as shown the figure. Then, secure
the brackets to both walls and the unit using the
included screws.
NOTE: If the unit is installed freestanding, please
place the brackets in front of the unit’s ventilation
grille and secure the brackets to the surface it is
being used on by the included screws.
Full Overlay Panel Installation Instructions
These models are designed for field-installed overlay panels. The overlay panels cover the stainless
steel to give a built-in appearance. The overlay panel and appropriate hardware are not included
with the unit and the end user needs to prepare them themselves. Please follow the instructions
below for installation:
The FF1DSS24 model includes a pre-installed stainless-steel panel, which must be removed before installing your own custom overlay panel. Please follow the instructions below:
A. Remove the screws securing the panel (2) to
the brackets (6). There should be four brackets
on the left and right sides of the drawer.
B. Remove all the screws (4) and washers (3)
attaching the stainless-steel handle (1) from the
stainless-steel drawer panel (2).
C. Carefully set the stainless-steel panel on a soft
or padded cloth to avoid damaging the panel.
D. If you are replacing the stainless-steel panel
8
Page 9
with a panel to fit the exact size of the drawer, remove the brackets (6) and the screws holding
them to the drawer (7). Save the brackets and screws.
Installing the panel (all models):
Remove any items stored inside the drawers. Press
the right slide release lever down and at the same
time lift the corresponding left slide lever up and pull
the drawer out until it is free of tracks and the
cabinet. (Fig. 1)
Peel off the gasket and remove the handle by
removing the two screws that attach the handle to
the door.
Drill the 2 holes shown by using a 3/16” drill bit on
the bottom of the drawer door front. (Fig. 2)
Cut the overlay panels with a thickness of 3/4” to
the dimensions corresponding to your model.*
If reusing the handles that came with the unit, drill
two holes with a diameter of 3/16” in the overlay
panel. Attach the handle and overlay panel together
to the drawer face using 2 M4x65 screws and
through the upper 2 existing holes inside the door
groove. Then attach the overlay panel to the drawer
face using 2 wood screws #10x2 (ST4x50) Type AB
Phillips and through
inside the door groove. (Fig. 3)
If user-supplied handles will be used, attach the
handles to the overlay panels by using the flat head
screws and drive the screws flush with the panels.
Then attach the overlay panel to the drawer face
using the 4 wood screws #10x2 (ST4x50) and
through the 4 existing holes inside the door groove.
Peel back the gaskets, then align the left and right
slide channels with the tracks in the cabinet.
Ensuring an even track engagement on both sides,
gently push the drawer into the cabinet until it stops.
the lower 2 existing holes
* Suggested Panel Sizes:
SDR24: 23.4” W x 15.6” H
SDR30: 29.5” W x 15.6” H
SDR36: 35.4” W x 15.6” H
FF1DSS models: 21.4” W x 15.6” H
9
Page 10
OPERATING YOUR APPLIANCE
It is recommended you install the appliance in a place where the ambient temperature is between
44º and 100ºF (7º to 38ºC). If the ambient temperature is above or below the recommended
temperatures, the performance of the unit may be affected. For example, placing your unit in
extremely cold or hot conditions may cause interior temperatures to fluctuate. The expected
operating temperature range may not be reached.
Control Panel
ON/OFF Power
To turn the appliance off, touch and hold the key for 5 seconds until the temperature display goes
off. To turn the appliance on, touch and hold the
lights up.
NOTE: Touching the POWER key once can switch off the audible alarm when the alarm is on.
Up +
Used to increase (warm) the set temperature by 1°C/1ºF.
Down -
Used to decrease (cool) the set temperature by 1°C/1ºF.
ºF/ºC Selector
Select the temperature display in Fahrenheit or Celsius degrees.
Indicator Light
The indicator light is the dot located at the bottom right corner of the display. The indicator light will
be on when a multi-key function is selected. To perform a multi-key function, touch and hold the first
key, then touch the second key for at least 5 seconds, and then release both keys.
Child Lock
The child lock will be activated automatically if, in 2 minutes or longer, no key is touched. To cancel
the lock, touch the UP and DOWN keys at the same time for at least 5 seconds and the indicator
light will flash three times to confirm the action.
Setting the Temperature Control
You can set the temperature by touching the UP and DOWN symbols. When you touch either of
the two buttons for the first time, the LED readout will show the original temperature set
previously. (The temperature preset at the factory is 39°F or 4°C.)
The temperature you are setting will increase by one degree each time you touch the UP symbol
key for 1 second until the temperature display
10
Page 11
NOTE:
and will decrease by one degree each time you touch the DOWN symbol.
The range of set temperatures is from 36°F to 43°F.
To view the set temperature at any time, touch the UP or DOWN symbol. The set temperature will
temporarily flash in the display window for 5 seconds. Then the display shows the current inner
temperature again.
If the unit is unplugged or power is lost or turned off, you must wait 3 to 5 minutes before
restarting the unit. If you attempt to restart before this time delay, the unit will not start.
When you use the unit for the first time or restart the unit after it has been shut off for a long
time, there could be a few degrees variance between the temperature you select and the one
indicated on the LED readout. This is normal and is due to the length of the activation time.
There should not be a problem once the unit has been running for a few hours.
Interior Light
The unit is equipped with interior LED lights which will be turned ON when the door is opened. LED
lights are designed for extremely long life. They are not user serviceable. To change them, please
contact the service department.
NOTE: Please use only the original LED light fittings provided by the manufacturer.
Sabbath Mode
Sabbath mode is available for the observance of certain religious holidays. This mode turns off
the displays, interior light, and audible alarms and prevents them from turning on again. Normal
cooling operations will still take place.
To initiate Sabbath mode, touch the POWER and ºC/F keys at the same time and hold for at
least 5 seconds. The indicator light (the dot at the bottom right of the display) will flash four times
and the display will go out to confirm the Sabbath mode is ON.
Sabbath mode can be canceled by repeating the above process. The Sabbath Mode will
automatically turn off after 48 hours.
Temperature Memory Function
In the event of a power interruption (power surge, breaker switch, etc.), the unit can remember the
previous temperature settings, and when power is recovered, the cabinet temperature will return to
the same set temperature as before the power went off.
Defrosting
Under normal operating conditions, the unit requires no manual defrosting.
The evaporator behind the rear wall of the unit defrosts automatically. The condensate collects in
the
drainage channel behind the rear wall of the unit and flows through the drainage hole into the
drip tray by the compressor where it evaporates.
However, frost may accumulate on the evaporator if the unit is repeatedly opened in high heat or
high humidity locations. If this frost pattern does not clear within 24 hours, your unit will require
manual defrosting.
11
Page 12
Temperature Alarm / Door Alarm
An audible alarm sounds if the storage temperature is not cold enough. The temperature display
flashes at the same time.
The cause of the temperature being too high may be:
– Warm fresh food was placed inside
– Too much warm ambient air flowed in when rearranging and removing food
– Power failure for some time
– The appliance is faulty.
The audible alarm is automatically silenced and the temperature display stops flashing when the
temperature is sufficiently cold again.
If a drawer has been left open for more than 60 seconds, the alarm will sound. Pressing the
POWER key once switches off the audible alarm.
12
Page 13
CARE AND MAINTENANCE
Cleaning your Appliance
Turn off the power, unplug the appliance, and remove all items, including racks and dividers.
Wash the inside surfaces with a solution of warm water and baking soda (about 2 tablespoons of
baking soda to a quart of water).
Wash the racks and dividers with a mild detergent solution.
Wring excess water out of the sponge or cloth when cleaning the area where the controls are
located, or any electrical parts.
Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry
with a clean, soft cloth.
Use an approved stainless steel cleaner to clean the doors and handles. Do not use steel wool
or a steel brush on the stainless steel.
CAUTION: Failure to unplug the appliance before cleaning could result in electrical shock or other
personal injuries.
Power Failure
Most power failures are corrected within a few hours and should not affect the temperature of your
appliance if you minimize the number of times the drawers are opened. If the power is going to be off
for a longer period of time, you need to take the proper steps to protect the contents.
Vacation Time
Short vacations: Leave the appliance operating during vacations of less than three weeks.
Long vacations: If the appliance will not be used for several months, remove all items, and turn
off the appliance. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave
the drawers open slightly, blocking them open if necessary.
Moving your Appliance
1. Remove all items.
2. Securely tape down all loose items (racks, dividers) inside your appliance.
3. Turn the adjustable legs up to the base to avoid damage.
4. Tape the drawer shut.
5. Be sure the appliance stays secure in the upright position during transportation. Also, protect the
outside of the appliance with a blanket or similar item.
Energy-Saving Tips
The appliance should be in the coolest area of the room or outdoor location, away from heat-
producing appliances and out of direct sunlight.
Ensure that the unit is ventilated. Never cover air vents.
Do not keep the drawer open any longer than necessary.
Let hot foods cool to room temperature before placing them in the unit. Overloading the unit
forces the compressor to run longer.
Be sure to wrap foods properly, and wipe containers dry before placing them in the unit. This
cuts down on frost build-up inside the unit.
Unit bins and racks should not be lined with aluminum foil, wax paper, or paper toweling. Liners
interfere with cold air circulation, making the unit less efficient.
Organize and label food to reduce drawer openings and extended searches. Remove as many
items as needed at one time and close the drawer as soon as possible.
13
Page 14
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
REMEDY
Appliance is not connected to a
Connect the appliance.
fuse.
The temperature is not set correctly.
Check the set temperature.
the dust.
The room temperature is higher than
properly.
Put the appliance in a cooler place.
replace it.
Appliance is not connected to a
control panel.
Connect the appliance.
The appliance is not properly leveled.
Level the appliance with adjustable
feet.
The rattling noise may come from the flow of the refrigerant, which is normal. As
may cause popping and crackling noises.
The appliance is not properly leveled.
Level the appliance with adjustable
feet.
Drawer
The appliance is not properly leveled.
Level the appliance with adjustable
You can solve many common problems easily, saving you the cost of a service call. Try the
suggestions below to see if you can solve the problem before calling the servicer.
Troubleshooting Guide
Appliance
does not
operate.
Appliance is
not cold
enough.
Appliance
turns itself on
and off
frequently.
power supply.
The appliance is turned off.
Tripped circuit breaker or blown fuse
The ambient temperature could
require a lower temperature setting.
Drawers were opened too often.
A drawer was not closed completely.
Drawer is not hermetically sealed.
The condenser is too dirty.
The ventilation opening is blocked or
too dusty.
average.
A large amount of food has been
added to the unit.
Drawers are opened too often.
A drawer is not closed completely.
A drawer gasket does not seal
Switch on the appliance.
Switch on circuit breaker or replace
Set a lower temperature.
Do not open drawers more often
than necessary.
Close drawer properly.
Check the seal and clean or replace
it.
Clean the condenser when
necessary.
Clear the obstructions and clean off
Leave the appliance to work for a
while until the set temperature has
been reached.
Do not open the drawers more
often than necessary.
Close drawer properly.
Check the drawer seal and clean or
power supply.
The light does
not work.
Vibrations
The appliance
makes too
much noise.
Tripped circuit breaker or a blown
fuse.
The light was switched off on the
each cycle ends, you may hear gurgling sounds caused by the flow of refrigerant
in your appliance.
If temperature fluctuations occur, the contraction and expansion of the inner walls
14
Switch on circuit breaker or replace
fuse.
Switch on the light.
Page 15
will not close
properly.
feet.
“E0” indicates a communication error
“E7” indicates door switch failure.
Call for service.
Has a drawer been open for longer than
added to the unit.
If yes, close the drawer.
The icon “--”
display.
The displayed temperature is out of
Only temperatures within the range
instead. This is normal.
Display “E0”,
“E1”. “E2”,
“E3”, “E4”,
“E5” or “E7”.
The gaskets are dirty.
The racks or bins are out of position.
for 3 zone models.
“E1” or “E2” indicates that the air
temperature sensor has failed.
“E3” or “E4” indicates that the defrost
sensor in the evaporator has failed.
“E5” indicates defrost heater failure.
Clean the drawer gaskets.
Check the racks and bins and refit
them correctly.
60 seconds? If not, then the
temperature has risen higher or fallen
The alarm
sounds and
the
temperature
display
flashes.
lower than the temperature that has
been set. This could be due to:
The appliance drawers are being
opened too often.
The ventilation opening is covered or
too dusty.
A lengthy interruption in the power
supply.
A large amount of food has been
is lit and
range.
flashing in the
temperature
If you have checked the table above and find that you still need help with your appliance, call our
Customer Service facility at 800-932-4267 between 9:00 AM and 5:00 PM ET. We will do our best to
answer your questions.
CALIFORNIA CARB/SNAP DISCLOSURE
This product uses eco-friendly hydrocarbon refrigerant and fully complies with California
CARB regulations.
However, we are required by California Law to provide the following disclosure statement in every
product sold in California.
"This equipment is prohibited from use in California with any refrigerants on the 'List of Prohibited
Substances' for that specific end-use, in accordance with California Code of Regulations, title 17,
section 95374. This disclosure statement has been reviewed and approved by Felix Storch, Inc. and
Felix Storch, Inc. attests, under penalty of perjury, that these statements are true and accurate."
This product does not use any refrigerants on the List of "Prohibited Substances".
Do not open drawers more often
than necessary.
Clear the obstructions and clean off
the dust.
Leave the appliance to work for a
while until the set temperature has
been reached.
0~99°F/-9~37°C can be displayed.
If the temperature is not within this
range, the icon “--” will be displayed
15
Page 16
LIMITED WARRANTY
For parts and accessory ordering,
www.summitappliance.com/support
Felix Storch, Inc.
www.summitappliance.com
ONE-YEAR LIMITED WARRANTY
Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is
operated and maintained according to instructions attached to or furnished with the product, the warrantor
will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service
must be provided by a designated service company. Outside the 48 states, all parts are warranted for one
year from manufacturing defects. Plastic parts, shelves, and cabinets are warranted to be manufactured to
commercially acceptable standards and are not covered from damage during handling or breakage.
5-YEAR COMPRESSOR WARRANTY
1. The compressor is covered for 5 years.
2. Replacement does not include labor.
ITEMS WARRANTOR WILL NOT PAY FOR:
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to
replace or repair fuses, or to correct wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs or broken shelves. Consumable parts (such as
filters) are excluded from warranty coverage.
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper
installation, installation not in accordance with electrical or plumbing codes, or use of products not
approved by the warrantor.
4. Replacement parts or repair labor costs for units operated outside the United States.
5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
6. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not
installed in accordance with published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES; L
THE CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE
PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR.
WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS,
WHICH VARY FROM STATE TO STATE.
An ISO 9001:2015 registered company
770 Garrison Ave
Bronx, New York 10474
IMITATION OF REMEDIES
troubleshooting and helpful hints, visit:
Printed in P.R.C.
16
Loading...