Summit DW2432SS Installation Manual
DISHWASHER
Models DW2432 and DW2432SS
Installation Manual
Write Serial Number (on inner door of unit) here:
_______________________________________
Felix Storch, Inc.
Summit Appliance Division
770 Garrison Avenue
Bronx, New York 10474
www.summitappliance.com
To prevent accidents which could cause serious injury or death, as well as
machine damage, read these instructions before installation and / or use:
Contents
1. IMPORTANT SAFETY INSTRUCTIONS 1
1.1 INSPECT THE DISHWASHER 2
1.2 HOW TO CONTACT US 2
2. TOOLS THAT MAY BE NEEDED 3
3. MATERIALS THAT MAY BE NEEDED 3
4. MATERIALS SUPPLIED 4
4.1 PARTS SUPPLIED 4
4.2 MANUAL BAG 4
4.3 DISHWASHER PARTS BAG 1 4
4.4 PARTS ATTACHED TO THE REAR OF THE DISHWASHER 4
5. DISHWASHER SPECIFICATIONS 5
5.1 TECHNICAL FEATURES 5
6. ENCLOSURE PREPARATION 6
6.1 ELECTRICAL PREPARATIONS 6
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS 7
6.3 ADJUSTING HEIGHT 7
6.4 INSTALLING THE SIDE TRIM STRIPS 9
6.5 PREPARING THE WATER CONNECTION (A) 10
6.6 DRAIN PREPARATION 11
6.7 STEAM PROTECTION FOIL 12
7. PLACEMENT OF DISHWASHER INTO THE OPENING 13
7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL
CONNECTIONS 13
7.2 ELECTRICAL CONNECTION 14
7.3 READJUSTING FOOT LEVELS 16
7.4 ADJUSTING THE MOVABLE TOE KICK 16
8. INSTALLER CHECKLIST 18
9. FINAL INSTRUCTIONS 18
10. SELF-HELP HINTS 18
INTRODUCTION
Please read this installation manual and
particularly the safety instructions
completely and carefully. They will save you
time and effort and help to ensure optimum
dishwasher performance.
Be sure to observe all listed warnings and
cautions. Look particularly for the icons with
exclamation marks inside. The information
icon also will provide important references.
WARNING:
Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.
CAUTION:
Indicates a potentially hazardous situation
which, if not avoided, may result in injury. It
may also be used to alert against unsafe
practices.
Notice:
Indicates a potentially hazardous situation
which, if not avoided, may result in damage
to the dishwasher, the tableware, the
equipment or the environment.
1. IMPORTANT SAFETY
INSTRUCTIONS
In addition to these instructions, the
dishwasher shall be installed:
In accordance with all local codes or, in
absence of a local code:
In the United States, with the National
Electric Code,
In Canada, with the Canadian Electric
Code C22.1 – latest edition/Provincial
and Municipal codes and/or local codes.
Notice:
Read these installation instructions
completely before installing and follow
them carefully. Save these instructions
and pass them on to any future user.
WARNING
When installing the dishwasher, follow
basic precautions, including the
following:
The dishwasher installation must be
performed in accordance with this
installation manual. If you did not receive
an installation manual, order it by calling
1-800-932-4267 or you may also
download it from our website at
www.summitappliance.com
Installation and repair should be
performed by a qualified installer. Work by
unqualified persons could be dangerous
and may void the warranty.
Notice:
Installation should be performed by an
insured licenser plumber, contractor or
trained installer. Installation performed by
persons other than this could result in
improper installation and property damage.
Do not operate the appliance if damaged,
malfunctioning, partially disassembled or
if it has missing or broken parts.
Also follow the safety instructions of the
user manual.
To reduce the risk of electric shock, fire,
or injury to persons, the installer must
ensure that the dishwasher is completely
enclosed at the time of installation.
Only connect the dishwasher to the power
supply when all installation and plumbing
work is complete.
If the dishwasher is installed in a location
that experiences freezing temperatures
(e.g., in a vacation home, cabin, etc.), you
must drain all the water from the
dishwasher’s interior. Water system
ruptures that occur as a result of freezing
are not covered by warranty.
Dishwasher must be secured to adjacent
cabinetry using the brackets provided.
Failure to do this may cause damage to
property or bodily injury.
Connect to a properly rated, protected
and sized power supply circuit to avoid
electrical overload. The dishwasher is
designed for an electrical supply of 120 V
(volts), 60 Hz (hertz), AC, connected to a
1
dishwasher-dedicated, properly grounded
electrical circuit with a fuse or breakers
rated for 15 amperes. Electrical supply
conductors shall be a minimum of #14
AWG copper wire rated at 75ºC (167ºF)
or higher. These requirements must be
met to prevent injury and machine
damage. Consult a qualified electrician if
in doubt.
Do not use any extension cord or portable
outlet device to connect the dishwasher to
a power supply.
Ensure that any plastic wrappings, bags,
small pieces etc. are disposed of safely
and kept out of the reach of children.
Danger of suffocation!
Remove the door to the washing
compartment when removing an old
dishwasher from service or discarding it.
Ensure that the appliance presents no
danger to children when being stored for
disposal.
Old appliances may contain materials that
can be recycled. Please contact your local
recycling authority about the possibility of
recycling these materials.
Notice:
The dishwasher drain hose must be
installed with a drain loop at least 28”
(710mm) off the cabinet floor; otherwise
the dishwasher may not drain properly.
This dishwasher is intended for residential
use only, and should not be used in
commercial establishments.
New installation – If the dishwasher is a
new installation, most of the work must be
done before the dishwasher is moved into
place.
Replacement – If the dishwasher is
replacing another dishwasher, check the
existing dishwasher connections for
compatibility with the new dishwasher,
and replace parts as necessary.
1.1 INSPECT THE DISHWASHER
After unpacking the dishwasher and prior to
installatio
dishwasher for possible freight or cosmetic
damage. Report any damage immediately.
Notice:
Cosmetic defects must be reported within
10 days of installation.
Do not discard any bags or items that
come with the original package until after
the entire installation has been
completed.
n, thoroughly inspect the
1.2 HOW TO CONTACT-US :
You may either call our Toll-Free Number at
1-800-932-4267 or contact us via the
website at
www.summitappliance.com
2
2. TOOLS THAT MAY BE NEEDED
3. MATERIALS THAT MAY BE NEEDED
(Additional materials may be required to comply with local codes)
Hot Water Supply Line – Minimum 3/8” O.D. copper tubing or metal braided
dishwasher supply line.
Electrical Supply Cable – Minimum #14AWG, 2 conductors, 1 ground, insulated
copper conductors.
90º elbow with 3/8” N.P.T male threads on one leg, and sized to fit your water
supply line (copper tubing/compression fitting, or braided hose) on the other leg.
UL-listed conduit connector or strain relief.
Teflon tape or other pipe thread compound to seal plumbing connections.
Shut-off valve and fittings appropriate for hot water supply line (copper
tubing/compression fitting, or braided hose).
Silicone
Glue
3
4. MATERIALS SUPPLIED
4.1 PARTS SUPPLIED
Parts for your dishwasher will come in several plastic bags. Check your
parts bags shown to make sure you have all the parts listed to the left.
4.2 MANUAL BAG
The dishwasher comes with a manual bag containing:
User manual
Installation manual
Quick reference guide
4.3 DISHWASHER PARTS BAG 1
This dishwasher bag comes with the following parts:
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
c. Adjusting Wrench
d. Screws ⅛” x ⅝” ( 3.5mm x 14mm)
e. Mounting Bracket Left
f. Mounting Bracket Right
g. Spring Clamp
h. Screw Clamp
j. Rubber Connector
k. Toe Kick Bracket – Left
l. Toe Kick Bracket – Right
m. Wire Nuts
n. Long Legs
o. Toe Kick (toe kick without slots)
p. Toe Kick
r. Toe Kick
s. Plastic Caps
t. Screws 3/16” x ¼” ( 4mm x 6mm)
u. Steam Protection Foil
4.4 PARTS ATTACHED TO THE REAR OF THE DISHWASHER
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
o. Toe Kick (toe kick without slots)
p. Toe Kick
r. Toe Kick
4
Loading...