Summit 42369 User Manual
A
S
f
(
SUMMIT
®
PLATINUM D4 , D6
BUILT-IN LP GAS GRILL INSTALLATION GUIDE
THIS GAS APPLIANCE IS DESIGNED
FOR OUTDOOR USE ONLY.
42369
LOCATING YOUR GRILL
When determining a suitable location for your Summit® gas grill installation, give attention to concerns such as exposure to wind, proximity to traffi c paths, and
keeping any gas supply lines as short as possible. Never locate the Summit® gas grill in a garage, breezeway, shed, under an unprotected overhang, or other
enclosed area. Locate the grill and structure so there is enough room to safely evacuate the area in case of a fi re.
CLEARANCE FROM SURFACES OR STRUCTURES
24 inches (61 cm) Any Surface
WARNING: Clearance from any surface or structure is
24 inches (609.6 mm) from the back and sides of the grill.
Refer to “Typical Gas Supply Installation” before starting
installation.
WARNING: The structure, “island”, countertops, and
adjacent work areas for the built-in grill installation must be
built from noncombustible materials only.
NOTE: If you have questions on what materials are considered noncombustible,
contact your local building materials supplier or fi re department.
BUILT-IN STRUCTURE CUTOUT DIMENSIONS
ALL DIMENSIONS ARE TO FINISHED SURFACES.
Any Surface
24 inches
24 inches
(61 cm)
27 inches (685.8 mm) min. for
lid clearance
Grill Frame
Note: For a countertop treatment: Recommended 3/4 inch
19.1 cm) overhang. Notch front edge for frame to fully
slide in.
(61 cm)
WARNING: All countertop fi nished surfaces must be
constructed of a noncombustible material.
ny
ur
ace
Built-In Cutout Dimensions
3
2
1
1
2
3
D4 D6 Tolerances
1
30
˝ 38
/
4
1
34
˝ 34
/
4
21˝ 21˝ +
1
˝+
/
4
1
˝+
/
4
1
” -
/
4
1
” -
/
4
1
” -
/
4
42369 US 11/22/05
1
˝
/
4
1
˝
/
4
1
˝
/
4
LP
2
BUILT-IN CUTOUT DIMENSIONS
GENERAL CONSTRUCTION DETAILS
Summit® Built-In unit and all other accessory units should be on site before construction begins.
1
All dimensions have a tolerance of plus or minus (+/-)
The grill frame rests directly on the Island Structure top fi nished surface. Make sure this surface is level. Do not support the grill from the
bottom.
If the supporting structure is going to have an electrical outlet for a rotisserie, it should be on the left side of the structure.
Refer to Summit
®
Built-In Tank Drawer Installation Instructions for complete gas line locations.
/4 inch (.635 mm).
24"
min.
24"
min.
30
21"
1
6
"
/
4
1
"
/
4
34
1
"
/
4
Built-In
Frame
Note: For a countertop treatment:
Recommended
Notch front edge for frame to fully slide in.
3
inch overhang.
/
4
24"
min.
24"
min.
21"
38
1
6
"
/
4
1
"
/
4
34
1
"
/
4
Built-In
Frame
Access for electric
on left hand side
D4
24"
min.
3
"
/
3
4
Gas Inlet
min.
Side Burner
Opening
27 inches min.
1
6
"
/
4
3
3
Gas Inlet
1/2"
10
distance from front
edge of the cutout
for open lid clearance
*Clearance from any surface or structure is at least 24 inches from the back and
sides of the grill.
Access for electric
on left hand side
10
3
3
"
/
4
Gas Inlet
1/2"
min.
24"
min.
Side Burner
Opening
27 inches min.
distance from front
edge of the cutout
for open lid clearance
D6
3
3
1
6
"
/
4
Gas Inlet
"
/
4
"
/
4
Note: For a countertop treatment:
Recommended
Notch front edge for frame to fully slide in.
3
inch overhang.
/
4
*Clearance from any surface or structure is at least 24 inches from the back and
sides of the grill.
Lid - 1
D4
PARTS LIST
Left Door - 1
3
Cookbox - 1
Lid - 1
Cookbox - 1
D6
OR
Right Door - 1
Warming Rack - 1
Warm-Up
Right Enclosure Panel - 1
™
Rack - 1
Front Frame Rail - 1
Rear Frame Rail - 1
Rear Panel
Assembly - 1
Bottom Shelf - 1
Left Enclosure Panel - 1
Front Vent Panel - 1
Rear Vent - 1
4
PARTS LIST
Flavorizer
Stainless Steel
Cooking Grates
®
Bars - 2 Sets
4B
6B
Bottom Tray - 1
Catch-Pan Holder - 1
- 2
- 3
Wrench - 1
x10 Sheet Metal Screws - 3
Plastic Anchors - 3
1/2 inch Bolts
(1/4 x 20 x 1/2 inch Bolt) - 8
#10-32 x 1/4 inch Steel Screws - 5
Nylon Washer - 8
Handle - 2
Catch-Pan - 1
Disposable Drip Pans - 2
Hinge Pin- 2
Hair Pin Cotter- 2
Corrugated gas line - 1
Right Front Vent Clip - 1
Left Front Vent Clip - 1
Handle Hardware - 4
Rotisserie - 1
Rotisserie Motor - 1
Rotisserie Bracket - 1
Keps Nuts (1/4 x 20 Blk Zinc) - 2
Rotisserie Bracket Hardware- 2
Smoker - 1
7/16 inch Wrench - 1
EXPLODED VIEW - PLATINUM D4
5
7740501 - Summit® Platinum D4 LP Built-In 092005
1
2
3
38
4
39
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
5
6
7
8
9
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
28
29
30
31
32
33
34
35
36
37
65
66
67
68
69
70
71
72
73
74
75
76
6
EXPLODED VIEW - PLATINUM D6
7790501 - Summit® Platinum D6 LP Built-In 092005
1
2
3
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
4
5
6
7
8
9
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
32
33
34
35
36
37
38
39
40
41
69
70
71
72
73
74
75
76
77
78
Loading...