Page 1
SUB-ZERO DESIGN GUIDE
REVISED 10/ 2016
Page 2
TABLE OF CONTENTS
3 BUILT-IN REFRIGERATION
40 PRO 48 REFRIGERATION
46 INTEGRATED REFRIGERATION
56 WINE STORAGE
88 UNDERCOUNTER REFRIGERATION
98 SUB-ZERO WARRANTIES
Features and specications are subject to change at any
time without notice. Visit subzero.com/specs for the most
up-to-date information.
Throughout this guide, dimensions may vary by ±
1
/8" (3).
Dimensions in parentheses are millimeters unless otherwise
specied.
Page 3
Page 4
BUILT-IN REFRIGERATION
Built-In Refrigeration
For the built-in line, Sub-Zero designers and engineers took
a fresh look at everything, inside and out. Exterior renements include redesigned grilles and lower-prole hinges.
Inside, new technology in food preservation makes the builtin line nothing short of revolutionary.
BUILT-IN MODELS
BI-36R BI-36RG BI-36F BI-30U BI-30UG BI-36U(ID) BI-36UG
BI-36UFD(ID) BI-42UFD(ID) BI-36S BI-42S(ID) BI-42SD BI-48S(ID) BI-48S
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
4 | Sub-Zero Customer Care 800.222.7820
Page 5
BUILT-IN REFRIGERATION
Specications
INTERIOR CAPACITY—CU FT (L)
ALL REFRIGERATOR | ALL FREEZER REFR FRZR
BI-36R 23.5 (665)
BI-36RG 23.4 (663)
BI-36F 22.7 (643)
OVER-AND-UNDER REFR FRZR
BI-30U 13.2 (374) 4.2 (119)
BI-30UG 13.1 (371) 4.2 (119)
BI-36U(ID) 16.4 (464) 5.3 (150)
BI-36UG 16.3 (462) 5.3 (150)
BI-36UFD(ID) 15.7 (445) 5.3 (150)
BI-42UFD(ID) 18.3 (518) 6.4 (181)
SIDE-BY-SIDE REFR FRZR
BI-36S 12.4 (351) 8.2 (232)
BI-42S 16.3 (462) 8.0 (227)
BI-42SID 15.8 (447) 7.9 (224)
BI-42SD 16.0 (453) 7.9 (224)
BI-48S 19.1 (541) 9.8 (278)
BI-48SID 18.6 (527) 9.6 (272)
BI-48SD 18.8 (532) 9.6 (272)
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
subzero.com/specs | 5
Page 6
BUILT-IN REFRIGERATION
Built-In Design Options
FRAMED
For the classic Sub-Zero look, choose framed custom
door panels that contrast with the stainless steel full-length
handles and louvered grille (shown). The framed application is an overlay model with framed design features. Panel,
grille and handle options are available.
Panels | Custom panels, stainless steel or white enamel.
Grille | Classic louvered grille insert or solid custom panel
for 84" (standard), 83" or 88" overall unit height. Dual wide
grille for dual installations.
Handles | Full-length standard or extended.
OVERLAY
Custom overlay door panels can be combined with unique
handle hardware for design exibility. Shown with pro
handle option to complement Wolf ranges. Customize with
panel, grille and handle options.
Panels | Custom panels or stainless steel.
Grille | Solid custom panel or pro louvered grille for 84"
(standard), 83" or 88" overall unit height. Dual wide grille for
dual installations.
Handles | Custom, tubular or pro handles.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
Framed.
6 | Sub-Zero Customer Care 800.222.7820
Overlay.
Page 7
BUILT-IN REFRIGERATION
Built-In Design Options
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
FLUSH INSET
The ush inset design option allows for ush door and grille
panels and custom handle hardware. Shown with tubular
handle option to match Wolf built-in ovens. The ush inset
application is an overlay model with ush inset panels. Customize with panel, grille and handle options.
Panels | Custom panels or stainless steel.
Grille | Solid custom panel or pro louvered grille for 84"
(standard), 83" or 88" overall unit height. Dual wide grille for
dual installations.
Handles | Custom, tubular or pro handles.
STAINLESS STEEL
For a professional look, classic stainless steel models
require no customization. To complement the look of Wolf
ranges, choose the pro handle option (shown). Grille and
handle options are available.
Grille | Pro louvered grille for 84" (standard), 83" or 88"
overall unit height. Dual wide grille for dual installations.
Handles | Tubular or pro handles.
Flush inset.
Stainless steel.
subzero.com/specs | 7
Page 8
BUILT-IN REFRIGERATION
Overall Dimensions
ALL REFRIGERATOR | ALL FREEZER
HEIGHT DIMENSIONS ±
237/8"
(606)
36"
(914)
1
/2" (13)
733/4"
(1873)
141/8"
(359)
84"
(2134)
4" (102)
263/16"
237/8"
(665)
(606)
Overall dimensions are based on stainless steel models.
1
For ush inset applications, add
/2" (13) to door clearance
dimensions.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
371/4"
(946)
23/8" (60)
Model BI-36R, BI-36RG, BI-36F.
8 | Sub-Zero Customer Care 800.222.7820
Page 9
BUILT-IN REFRIGERATION
Overall Dimensions
OVER-AND-UNDER
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
HEIGHT DIMENSIONS ±
237/8"
(606)
30" (762)
263/16" (665)
84"
(2134)
503/4"
(1289)
23"
(584)
1
/2"
(13)
121/8"
(308)
4" (102)
237/8" (606)
HEIGHT DIMENSIONS ±
237/8"
(606)
36" (914)
263/16" (665)
84"
(2134)
503/4"
(1289)
23"
(584)
1
(13)
/2"
141/8"
(359)
4" (102)
237/8" (606)
235/8"
(600)
Model BI-30U, BI-30UG.
311/4"
23/8" (60)
(796)
235/8"
(600)
Model BI-36U(ID), BI-36UG.
371/4"
(946)
23/8" (60)
subzero.com/specs | 9
Page 10
BUILT-IN REFRIGERATION
Overall Dimensions
OVER-AND-UNDER
HEIGHT DIMENSIONS ±
8"
(203)
36" (914)
263/16" (665)
84"
(2134)
503/4"
(1289)
23"
(584)
1
(13)
/2"
237/8"
(606)
4" (102)
237/8" (606)
HEIGHT DIMENSIONS ±
9"
(229)
42" (1067)
1
/2" (13)
503/4"
(1289)
23"
(584)
237/8"
(606)
84"
(2134)
4" (102)
263/16" (665)
237/8" (606)
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
235/8"
191/2"
(600)
(495)
23/8" (60)
Model BI-36UFD(ID).
10 | Sub-Zero Customer Care 800.222.7820
23/8" (60)
Model BI-42UFD(ID).
235/8"
(600)
221/4"
(565)
Page 11
BUILT-IN REFRIGERATION
Overall Dimensions
SIDE-BY-SIDE
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
HEIGHT DIMENSIONS ±
71/4"
(184)
36" (914)
1
/2" (13)
733/4"
(1873)
83/4"
(222)
84"
(2134)
4" (102)
237/8"
(606)
263/16" (665)
237/8" (606)
HEIGHT DIMENSIONS ±
71/2"
(191)
42" (1067)
1
/2" (13)
733/4"
(1873)
103/8"
(264)
84"
(2134)
4" (102)
237/8"
(606)
263/16" (665)
237/8" (606)
Model BI-36S.
221/4"
(565)
23/8" (60)
Model BI-42S(ID), BI-42SD.
261/4"
(668)
23/8" (60)
subzero.com/specs | 11
Page 12
BUILT-IN REFRIGERATION
48" (1219)
84"
(2134)
4"
(102)
733/4"
(1873)
237/8" (606)
237/8"
(606)
30"
(762)
115/8"
(295)
83/8"
(213)
23/8" (60)
HEIGHT DIMENSIONS ±
1
/2" (13)
263/16" (665)
Overall Dimensions
SIDE-BY-SIDE
Model BI-48S(ID), BI-48SD.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
12 | Sub-Zero Customer Care 800.222.7820
Page 13
BUILT-IN REFRIGERATION
Specications
SHIPPING WEIGHT
ALL REFRIGERATOR | ALL FREEZER LB (KG)
BI-36R 420 (191)
BI-36RG 430 (195)
BI-36F 406 (184)
OVER-AND-UNDER LB
BI-30U 462 (210)
BI-30UG 476 (216)
BI-36U(ID) 515 (234)
BI-36UG 529 (240)
BI-36UFD(ID) 529 (240)
BI-42UFD(ID) 582 (264)
SIDE-BY-SIDE LB
BI-36S 538 (244)
BI-42S 582 (264)
BI-42SID 608 (276)
BI-42SD 608 (276)
BI-48S 630 (286)
BI-48SID 656 (298)
BI-48SD 656 (298)
Shipping weights are based on stainless steel models.
(KG)
(KG)
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
subzero.com/specs | 13
Page 14
BUILT-IN REFRIGERATION
NOTE: Shaded line represents profile of unit.
SIDE
Opening Dimensions
STANDARD INSTALLATION
24" (610)
OPENING
DEPTH
TOP VIEW
W
OPENING WIDTH
FRONT VIEW
VIEW
833/4"
(2127)
OPENING
HEIGHT
OPENING WIDTH
30" Model 291/2" (749)
36" Model 351/2" (902)
42" Model 411/2" (1054)
48" Model 471/2" (1206)
W
If an 83" (2108) grille height is specied, the opening height
7
must be decreased by
specied, the opening height must be increased by 4"
/8" (22). If an 88" (2235) grille height is
(102).
If two units are installed side by side, refer to page 16 for
dual standard installations.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
14 | Sub-Zero Customer Care 800.222.7820
Page 15
BUILT-IN REFRIGERATION
*3
NOTE: Shaded line represents profile of unit with
SIDE
Opening Dimensions
FLUSH INSET INSTALLATION
263/16"
(665)
FLUSH
INSET
23/16"
DEPTH
(56)
TOP VIEW
FINISHED
CLEATS*
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
1
/4"
(6)
84"
(2134)
FLUSH
INSET
HEIGHT
VIEW
" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
3/4" (19) panel.
11/4"
(32)
FLUSH INSET WIDTH
FRONT VIEW
W
4" (102)
11/4"
(32)
3"
(76)*
TYPICAL
23/16"
(56)
FLUSH INSET WIDTH
30" Model 32" (813)
36" Model 38" (965)
42" Model 44" (1118)
48" Model 50" (1270)
W
Dimensions assume a 3/4" (19) panel thickness.
If an 83"
height must be decreased by
(2108) grille height is specied, the ush inset
7
/8" (22). If an 88" (2235) grille
height is specied, the ush inset height must be increased
(102).
by 4"
If two units are installed side by side, refer to page 17 for
dual ush inset installations.
subzero.com/specs | 15
Page 16
BUILT-IN REFRIGERATION
NOTE: Shaded line represents profile of unit.
SIDE
Opening Dimensions
DUAL STANDARD INSTALLATION
24" (610)
OPENING
DEPTH
TOP VIEW
VIEW
833/4"
(2127)
OPENING
HEIGHT
OPENING WIDTH
FRONT VIEW
DUAL OPENING WIDTH
Two 30" Models 593/4" (1518)
30" and 36" Models 653/4" (1670)
Two 36" Models 713/4" (1822)
W
W
A dual installation kit will be required for this installation.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
16 | Sub-Zero Customer Care 800.222.7820
Page 17
BUILT-IN REFRIGERATION
*3
NOTE: Shaded line represents profile of unit with
SIDE
Opening Dimensions
DUAL FLUSH INSET INSTALLATION
263/16"
(665)
FLUSH
INSET
23/16"
DEPTH
(56)
TOP VIEW
FINISHED
CLEATS*
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
1
/4"
(6)
84"
(2134)
FLUSH
INSET
HEIGHT
VIEW
" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
3/4" (19) panel.
11/4"
(32)
FLUSH INSET WIDTH
FRONT VIEW
W
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
23/16"
(56)
DUAL FLUSH INSET WIDTH
Two 30" Models 621/4" (1581)
30" and 36" Models 681/4" (1734)
Two 36" Models 741/4" (1886)
W
Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.
subzero.com/specs | 17
Page 18
BUILT-IN REFRIGERATION
Electrical
The electrical supply should be located within the shaded
area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit
interrupter (GFCI) is not recommended and may cause
interruption of operation.
Installation must comply with all applicable electrical codes.
ELECTRICAL REQUIREMENTS
Electrical Supply 115 VAC, 60 Hz
Service 15 amp
Receptacle 3-prong grounding-type
7"
E
(178)
6"
(152)
751/2" (1918)
FROM FLOOR
RIGHT SIDE
OF OPENING
Plumbing
The water supply line should be located within the shaded
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self-piercing valves.
The water supply line must not interfere with installation of
the anti-tip brackets.
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi
to the unit at all times. A copper line is not recommended
for this application.
Installation must comply with all applicable plumbing codes.
PLUMBING REQUIREMENTS
Water Supply
Pressure 35–120 psi
Excess Line for Connection 36" (914)
RIGHT SIDE
OF OPENING
1
/4" OD copper, braided stainless
(2.4–8.3 bar) supplied
steel or PEX tubing
(2.4–8.3 bar)
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
Electrical supply location.
18 | Sub-Zero Customer Care 800.222.7820
1
/2" (13)
6" (152)
18" (457)
AREA EXTENDS
FORWARD ON FLOOR
Water supply location.
3" (76)
Page 19
BUILT-IN REFRIGERATION
Custom Panels
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
For framed, overlay and ush inset applications, custom
door panels must be provided. Handle hardware must
also be provided for overlay and ush inset applications.
Refer to panel requirements below and the charts on pages
22–27 for custom panel dimensions for your specic design
application.
IMPORTANT NOTE: Do not cover a glass door with a solid
panel.
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
PANEL REQUIREMENTS
WEIGHT PER PANEL MAX
BI-36R, BI-36RG, BI-36F 75 lb (34 kg)
All Other Models 50 lb (23 kg)
Grille Panel 13 lb (6 kg)
PANEL THICKNESS MIN
Framed
Overlay and Flush Inset
1
/4" (6)
5
/8" (16)
FRAMED PANELS
The framed application is an overlay model with framed
design features. It is not a separate model.
1
If the custom panel is thinner than
/4" (6), a ller material
must be added to achieve a proper t. If the panel is thicker
1
/4" (6), rout an edge around the panel or mount the
than
custom panel on a sheet of
1
/4" (6) thick material and insert
into the channel. Refer to the illustrations below.
Routing, recessing or optional extended handles may be
required for nger clearance. Refer to the full-scale template
on page 34.
When installing two units side by side, refer to page 16 for
dual standard installations.
1
/4" (6) TRIM REVEAL
1
/4" (6) PANEL
DOOR
1
/4" (6) min
ROUT TO
DOOR
1
/4" (6)
Panel 1/4" thick or less.
Panel thicker than 1/4".
subzero.com/specs | 19
Page 20
BUILT-IN REFRIGERATION
Custom Panels
PARTIAL FRAMED OPTION
The partial framed kit includes a stainless steel panel for
above and below the external dispenser. Refer to the chart
below for panel width. The kit is avail able through an authorized Sub-Zero dealer. For local dealer information, visit the
nd a showroom section of our website, subzero.com.
PARTIAL FRAMED PANEL
BI-42SD 151/16" (383)
BI-48SD 183/4" (476)
PANEL MOUNTING KIT
A Sub-Zero custom panel mounting kit eliminates the need
for a backer and spacer panel and is avail able through an
authorized Sub-Zero dealer. For local dealer information, visit
the nd a showroom section of our website, subzero.com.
The kit consists of mounting cleats, screws and gages used
to properly position the cleats. The kit is available for all
W
built-in models except glass door models. Dual installations
require two mounting kits.
OVERLAY PANELS
Overlay panels are typically created by combining a 3/4" (19)
custom panel, a .10"
(3) spacer panel and a
1
/4" (6) backer
panel. Refer to the illustrations below.
When installing two units side by side, refer to page 16 for
dual standard installations.
SPACER PANEL
CUSTOM PANEL
CUSTOM
PANEL
SPACER
PANEL
BACKER PANEL
TRIM
5
/16" (8) min
1
/8" (3) (OVERLAY)
3
/4"
(19)
typical
.10" (3)
1
/4" (6)
BACKER
PANEL
Panel assembly (cross section). Panel assembly (rear view).
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
20 | Sub-Zero Customer Care 800.222.7820
Page 21
BUILT-IN REFRIGERATION
65/16" (160)
3
/32"
(2)
5
/8"
(16)
127/8"
(327)
65/16" (160)
3
/16"
(5)
127/8"
(327)
Custom Panels
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
FLUSH INSET PANELS
The ush inset application is an overlay model with ush
inset panels. It is not a separate model.
The ush inset design allows custom panels to be installed
ush with adjacent cabinets. Similar to overlay, ush inset
3
panels are typically created by combining a
panel, a .10"
(3) spacer panel and a
1
/4" (6) backer panel.
/4" (19) custom
Refer to the illustrations for overlay panels.
3
For ush inset panels thicker than
/4" (19), a 90° door stop
may be required to prevent interference with adjacent
cabinets. Refer to the full-scale templates at the end of this
guide.
When installing two units side by side, refer to page 17 for
dual ush inset installations.
ICE AND WATER DISPENSER
For models BI-42SD and BI-48SD, the refrigerator door
panel must include a cut-out to accommodate the external
dispenser. The thickness of the panel in this area can range
1
/4" (6) to a maximum of 11/8" (29). Refer to the illustra-
from
tions below.
Dispenser dimensions.
2"
(51)
1"
(25)
HANDLE
GLASSWELL
Dispenser dimensions.
Handle placement.
subzero.com/specs | 21
Page 22
BUILT-IN REFRIGERATION
H
H
H
W
AA
A
A
H
H
W
AA
A
B
H
H
H
W
H
H
H
W
W W
H
H
H
W
AA
A
A
H
H
H
W
W W
H
H
H
W
AA
A
A
H
H
H
W
H
H
H
W
W W
H
H
H
W
W W
Framed Panel Dimensions
W
BI-36R, BI-36F
H
A
H
B
W
BI-36RG
H
H
AA
BI-30U, BI-36U(ID)
MODEL BI-36R, BI-36RG, BI-36F
REFRIGERATOR/FREEZER W H
Door Panel 353/4" (908) 699/16" (1767)
GRILLE (OPTIONAL) W H
Grille Panel 353/4" (908) 815/16" (227)
BI-36RG A B
Stiles | Rails 53/16" (132) 105/16" (262)
MODEL BI-30U, BI-30UG
REFRIGERATOR W H
Door Panel 293/4" (756) 4915/16" (1268)
FREEZER W H
Drawer Panel 293/4" (756) 1811/16" (475)
GRILLE (OPTIONAL) W H
Grille Panel 293/4" (756) 815/16" (227)
BI-30UG A
Stiles | Rails 53/16" (132)
H
A
H
A
H
W
W
BI-30UG, BI-36UG
H
AA
H
W W
H
BI-36UFD(ID),
BI-42UFD(ID)
MODEL BI-36U(ID), BI-36UG
REFRIGERATOR W H
Door Panel 353/4" (908) 4915/16" (1268)
FREEZER W H
Drawer Panel 353/4" (908) 1811/16" (475)
GRILLE (OPTIONAL) W H
Grille Panel 353/4" (908) 815/16" (227)
BI-36UG A
Stiles | Rails 53/16" (132)
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PANELS) W H
Door Panel 175/8" (448) 4915/16" (1268)
FREEZER W H
Drawer Panel 353/4" (908) 1811/16" (475)
GRILLE (OPTIONAL) W H
Grille Panel 353/4" (908) 815/16" (227)
H
H
H
W
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
22 | Sub-Zero Customer Care 800.222.7820
MODEL BI-42UFD(ID)
REFRIGERATOR (2 PANELS) W H
Door Panel 205/8" (524) 4915/16" (1268)
FREEZER W H
Drawer Panel 413/4" (1060) 1811/16" (475)
GRILLE (OPTIONAL) W H
Grille Panel 413/4" (1060) 815/16" (227)
Page 23
BUILT-IN REFRIGERATION
H
H
H
W
AA
A
A
H
H
W
H
H
W
AA
A
B
H
H
H
W
H
H
H
WW
B
A
H
H
W
W W
H
H
H
W
AA
A
A
H
H
W
AA
A
B
H
H
H
W
H
H
H
W
W W
Framed Panel Dimensions
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
H
H
A
B
W
BI-36S, BI-42S(ID),
W
WW
BI-42SD, BI-48SD
BI-48S(ID)
MODEL BI-36S
REFRIGERATOR W H
Door Panel 1913/16" (503) 699/16" (1767)
FREEZER W H
Door Panel 157/16" (392) 699/16" (1767)
GRILLE (OPTIONAL) W H
Grille Panel 353/4" (908) 815/16" (227)
MODEL BI-42S, BI-42SID, BI-42SD
REFRIGERATOR W H
Door Panel 2413/16" (630) 699/16" (1767)
FREEZER W H
Door Panel 167/16" (418) 699/16" (1767)
GRILLE (OPTIONAL) W H
Grille Panel 413/4" (1060) 815/16" (227)
BI-42SD W H
Dispenser Cut-Out* 57/8" (149) 127/16" (316)
A B
Cut-Out Location 17/8" (48) 283/4" (730)
H
H
MODEL BI-48S, BI-48SID, BI-48SD
REFRIGERATOR W H
Door Panel 281/2" (724) 699/16" (1767)
FREEZER W H
Door Panel 183/4" (476) 699/16" (1767)
GRILLE (OPTIONAL) W H
Grille Panel 473/4" (1213) 815/16" (227)
BI-48SD W H
Dispenser Cut-Out* 57/8" (149) 127/16" (316)
Cut-Out Location 17/8" (48) 283/4" (730)
*For models BI-42SD and BI-48SD, panel thickness in dispenser area can
range from
landing area to accommodate dispenser.
1
/4" (6) to 11/8" (29) max. If panel is thicker, rout out 1/4" (6) min at
A B
subzero.com/specs | 23
Page 24
BUILT-IN REFRIGERATION
H
H
H
W
AA
A
A
H
H
W
AA
A
B
H
H
H
W
H
H
H
W
W W
H
H
H
W
AA
A
A
H
H
H
W
W W
H
H
H
W
AA
A
A
H
H
H
W
H
H
H
W
W W
H
H
H
W
W W
Overlay Panel Dimensions
W
BI-36R, BI-36F
H
A
H
B
W
BI-36RG
H
H
AA
BI-30U, BI-36U(ID)
MODEL BI-36R, BI-36RG, BI-36F
REFRIGERATOR | FREEZER W H
Overlay Panel 36" (914) 693/4" (1772)
Spacer Panel 351/8" (892) 6815/16" (1751)
Backer Panel 353/4" (908) 699/16" (1767)
GRILLE W H
Overlay Panel 36" (914) 91/4" (235)*
1
Spacer Panel 35
/8" (892) 85/16" (211)
Backer Panel 353/4" (908) 815/16" (227)
BI-36RG A B
Stiles | Rails 51/4" (133) 103/8" (264)
MODEL BI-30U, BI-30UG
REFRIGERATOR W H
Overlay Panel 30" (762) 501/8" (1273)
Spacer Panel 291/8" (740) 495/16" (1253)
Backer Panel 293/4" (756) 4915/16" (1268)
FREEZER W H
Overlay Panel 30" (762) 19" (483)
Spacer Panel 291/8" (740) 181/16" (459)
Backer Panel 293/4" (756) 1811/16" (475)
GRILLE W H
Overlay Panel 30" (762) 91/4" (235)*
Spacer Panel 29
Backer Panel 293/4" (756) 815/16" (227)
BI-30UG A
Stiles | Rails 51/4" (133)
1
/8" (740) 85/16" (211)
H
A
H
A
H
W
W
BI-30UG, BI-36UG
H
AA
H
W W
H
BI-36UFD(ID),
BI-42UFD(ID)
MODEL BI-36U(ID), BI-36UG
REFRIGERATOR W H
Overlay Panel 36" (914) 501/8" (1273)
Spacer Panel 351/8" (892) 495/16" (1253)
Backer Panel 353/4" (908) 4915/16" (1268)
FREEZER W H
Overlay Panel 36" (914) 19" (483)
Spacer Panel 351/8" (892) 181/16" (459)
Backer Panel 353/4" (908) 1811/16" (475)
GRILLE W H
Overlay Panel 36" (914) 91/4" (235)*
Spacer Panel 351/8" (892) 85/16" (211)
Backer Panel 353/4" (908) 815/16" (227)
BI-36UG A
Stiles | Rails 51/4" (133)
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PANELS) W H
Overlay Panel 177/8" (454) 501/8" (1273)
Spacer Panel 17" (432) 495/16" (1253)
Backer Panel 175/8" (448) 4915/16" (1268)
FREEZER W H
Overlay Panel 36" (914) 19" (483)
Spacer Panel 351/8" (892) 181/16" (459)
Backer Panel 353/4" (908) 1811/16" (475)
GRILLE W H
Overlay Panel 36" (914) 91/4" (235)*
Spacer Panel 35
1
/8" (892) 85/16" (211)
Backer Panel 353/4" (908) 815/16" (227)
H
H
H
W
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
24 | Sub-Zero Customer Care 800.222.7820
Page 25
BUILT-IN REFRIGERATION
H
H
H
W
AA
A
A
H
H
W
H
H
W
AA
A
B
H
H
H
W
H
H
H
WW
B
A
H
H
W
W W
H
H
H
W
AA
A
A
H
H
W
AA
A
B
H
H
H
W
H
H
H
W
W W
Overlay Panel Dimensions
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
H
H
A
B
W
BI-36S, BI-42S(ID),
W
WW
BI-42SD, BI-48SD
BI-48S(ID)
MODEL BI-42UFD(ID)
REFRIGERATOR (2 PANELS) W H
Overlay Panel 207/8" (530) 501/8" (1273)
Spacer Panel 20" (508) 495/16" (1253)
Backer Panel 205/8" (524) 4915/16" (1268)
FREEZER W H
Overlay Panel 42" (1067) 19" (483)
Spacer Panel 411/8" (1045) 181/16" (459)
Backer Panel 413/4" (1060) 1811/16" (475)
GRILLE W H
Overlay Panel 42" (1067) 91/4" (235)*
Spacer Panel 411/8" (1045) 85/16" (211)
Backer Panel 413/4" (1060) 815/16" (227)
MODEL BI-36S
REFRIGERATOR W H
Overlay Panel 201/16" (510) 693/4" (1772)
Spacer Panel 193/16" (487) 6815/16" (1751)
Backer Panel 1913/16" (503) 699/16" (1767)
FREEZER W H
Overlay Panel 1511/16" (398) 693/4" (1772)
Spacer Panel 1413/16" (376) 6815/16" (1751)
Backer Panel 157/16" (392) 699/16" (1767)
GRILLE W H
Overlay Panel 36" (914) 91/4" (235)*
1
Spacer Panel 35
/8" (892) 85/16" (211)
Backer Panel 353/4" (908) 815/16" (227)
H
MODEL BI-42S, BI-42SID, BI-42SD
REFRIGERATOR W H
Overlay Panel 251/16" (637) 693/4" (1772)
Spacer Panel 243/16" (614) 6815/16" (1751)
H
Backer Panel 2413/16" (630) 699/16" (1767)
FREEZER W H
Overlay Panel 1611/16" (424) 693/4" (1772)
Spacer Panel 1513/16" (402) 6815/16" (1751)
Backer Panel 167/16" (418) 699/16" (1767)
GRILLE W H
Overlay Panel 42" (1067) 91/4" (235)*
1
Spacer Panel 41
/8" (1045) 85/16" (211)
Backer Panel 413/4" (1060) 815/16" (227)
BI-42SD W H
Dispenser Cut-Out 57/8" (149) 127/16" (316)
A B
Cut-Out Location 2" (51) 2813/16" (732)
MODEL BI-48S, BI-48SID, BI-48SD
REFRIGERATOR W H
Overlay Panel 283/4" (730) 693/4" (1772)
Spacer Panel 277/8" (708) 6815/16" (1751)
Backer Panel 281/2" (724) 699/16" (1767)
FREEZER W H
Overlay Panel 19" (483) 693/4" (1772)
Spacer Panel 181/8" (460) 6815/16" (1751)
Backer Panel 183/4" (476) 699/16" (1767)
GRILLE W H
Overlay Panel 48" (1219) 91/4" (235)*
Spacer Panel 47
1
/8" (1197) 85/16" (211)
Backer Panel 473/4" (1213) 815/16" (227)
BI-48SD W H
Dispenser Cut-Out 57/8" (149) 127/16" (316)
A B
Cut-Out Location 2" (51) 2813/16" (732)
*Panel height may be increased by
refer to built-in panel congurator at subzero.com/trade/panels.
Grille panel dimensions are for standard 84"
83"
(2108) height, subtract 1" (25) from grille panel height dimensions and for
88"
(2235) height, add 4" (102). A specic panel grille must be ordered for an
83" or 88" overall unit height.
7
/16" (11) to hide upper main frame. Also
(2134) overall unit height. For
subzero.com/specs | 25
Page 26
BUILT-IN REFRIGERATION
H
H
H
W
AA
B
B
H
H
W
AA
A
B
H
H
H
W
H
H
H
W
W W
H
H
H
W
AA
B
B
H
H
H
W
W W
H
H
H
W
AA
A
A
H
H
H
W
H
H
H
W
W W
H
H
H
W
W W
Flush Inset Panel Dimensions
H
H
AA
BI-30U, BI-36U(ID)
W
BI-36R, BI-36F
H
A
H
B
W
BI-36RG
MODEL BI-36R, BI-36RG, BI-36F
REFRIGERATOR | FREEZER W H
Flush Inset Panel 37" (940) 693/4" (1772)
Spacer Panel 351/8" (892) 6815/16" (1751)
Backer Panel 353/4" (908) 699/16" (1767)
GRILLE W H
Flush Inset Panel 37" (940) 91/4" (235)
Spacer Panel 351/8" (892) 85/16" (211)
Backer Panel 353/4" (908) 815/16" (227)
BI-36RG A B
Stiles | Rails 53/4" (146) 103/8" (264)
MODEL BI-30U, BI-30UG
REFRIGERATOR W H
Flush Inset Panel 31" (787) 501/8" (1273)
Spacer Panel 291/8" (740) 495/16" (1253)
Backer Panel 293/4" (756) 4915/16" (1268)
FREEZER W H
Flush Inset Panel 31" (787) 19" (483)
Spacer Panel 291/8" (740) 181/16" (459)
Backer Panel 293/4" (756) 1811/16" (475)
GRILLE W H
Flush Inset Panel 31" (787) 91/4" (235)
Spacer Panel 291/8" (740) 85/16" (211)
Backer Panel 293/4" (756) 815/16" (227)
BI-30UG A B
Stiles | Rails 53/4" (146) 51/4" (133)
H
B
H
B
H
W
W
BI-30UG, BI-36UG
H
AA
H
W W
H
BI-36UFD(ID),
BI-42UFD(ID)
MODEL BI-36U(ID), BI-36UG
REFRIGERATOR W H
Flush Inset Panel 37" (940) 501/8" (1273)
Spacer Panel 351/8" (892) 495/16" (1253)
Backer Panel 353/4" (908) 4915/16" (1268)
FREEZER W H
Flush Inset Panel 37" (940) 19" (483)
Spacer Panel 351/8" (892) 181/16" (459)
Backer Panel 353/4" (908) 1811/16" (475)
GRILLE W H
Flush Inset Panel 37" (940) 91/4" (235)
Spacer Panel 351/8" (892) 85/16" (211)
Backer Panel 353/4" (908) 815/16" (227)
BI-36UG A B
Stiles | Rails 53/4" (146) 51/4" (133)
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PANELS) W H
Flush Inset Panel 183/8" (467) 501/8" (1273)
Spacer Panel 17" (432) 495/16" (1253)
Backer Panel 175/8" (448) 4915/16" (1268)
FREEZER W H
Flush Inset Panel 37" (940) 19" (483)
Spacer Panel 351/8" (892) 181/16" (459)
Backer Panel 353/4" (908) 1811/16" (475)
GRILLE W H
Flush Inset Panel 37" (940) 91/4" (235)
Spacer Panel 351/8" (892) 85/16" (211)
Backer Panel 353/4" (908) 815/16" (227)
H
H
H
W
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
26 | Sub-Zero Customer Care 800.222.7820
Page 27
BUILT-IN REFRIGERATION
H
H
H
W
AA
A
A
H
H
W
H
H
W
AA
A
B
H
H
H
W
H
H
H
WW
B
A
H
H
W
W W
H
H
H
W
AA
A
A
H
H
W
AA
A
B
H
H
H
W
H
H
H
W
W W
Flush Inset Panel Dimensions
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
H
H
A
B
W
BI-36S, BI-42S(ID),
W
WW
BI-42SD, BI-48SD
BI-48S(ID)
MODEL BI-42UFD(ID)
REFRIGERATOR (2 PANELS) W H
Flush Inset Panel 213/8" (543) 501/8" (1273)
Spacer Panel 20" (508) 495/16" (1253)
Backer Panel 205/8" (524) 4915/16" (1268)
FREEZER W H
Flush Inset Panel 43" (1092) 19" (483)
Spacer Panel 411/8" (1045) 181/16" (459)
Backer Panel 413/4" (1060) 1811/16" (475)
GRILLE W H
Flush Inset Panel 43" (1092) 91/4" (235)
Spacer Panel 411/8" (1045) 85/16" (211)
Backer Panel 413/4" (1060) 815/16" (227)
MODEL BI-36S
REFRIGERATOR W H
Flush Inset Panel 209/16" (522) 693/4" (1772)
Spacer Panel 193/16" (487) 6815/16" (1751)
Backer Panel 1913/16" (503) 699/16" (1767)
FREEZER W H
Flush Inset Panel 163/16" (411) 693/4" (1772)
Spacer Panel 1413/16" (376) 6815/16" (1751)
Backer Panel 157/16" (392) 699/16" (1767)
GRILLE W H
Flush Inset Panel 37" (940) 91/4" (235)
Spacer Panel 351/8" (892) 85/16" (211)
Backer Panel 353/4" (908) 815/16" (227)
H
MODEL BI-42S, BI-42SID, BI-42SD
REFRIGERATOR W H
Flush Inset Panel 259/16" (649) 693/4" (1772)
Spacer Panel 243/16" (614) 6815/16" (1751)
H
Backer Panel 2413/16" (630) 699/16" (1767)
FREEZER W H
Flush Inset Panel 173/16" (437) 693/4" (1772)
Spacer Panel 1513/16" (402) 6815/16" (1751)
Backer Panel 167/16" (418) 699/16" (1767)
GRILLE W H
Flush Inset Panel 43" (1092) 91/4" (235)
Spacer Panel 411/8" (1045) 85/16" (211)
Backer Panel 413/4" (1060) 815/16" (227)
BI-42SD W H
Dispenser Cut-Out 57/8" (149) 127/16" (316)
A B
Cut-Out Location 2" (51) 2813/16" (732)
MODEL BI-48S, BI-48SID, BI-48SD
REFRIGERATOR W H
Flush Inset Panel 291/4" (743) 693/4" (1772)
Spacer Panel 277/8" (708) 6815/16" (1751)
Backer Panel 281/2" (724) 699/16" (1767)
FREEZER W H
Flush Inset Panel 191/2" (495) 693/4" (1772)
Spacer Panel 181/8" (460) 6815/16" (1751)
Backer Panel 183/4" (476) 699/16" (1767)
Flush Inset Panel 49" (1245) 91/4" (235)
GRILLE W H
Spacer Panel 471/8" (1197) 85/16" (211)
Backer Panel 473/4" (1213) 815/16" (227)
BI-48SD W H
Dispenser Cut-Out 57/8" (149) 127/16" (316)
A B
Cut-Out Location 2" (51) 2813/16" (732)
Grille panel dimensions are for standard 84"
83"
(2108) height, subtract 1" (25) from grille panel height dimensions and for
88"
(2235) height, add 4" (102). A specic panel grille must be ordered for an
83" or 88" overall unit height.
(2134) overall unit height. For
subzero.com/specs | 27
Page 28
BUILT-IN REFRIGERATION
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEW
5
/8"
(16)
5
/16"
(8)
1
/2"
(13)
1
/2"(13)
3
/32"
(2)
5
/16"
(8)
5
/16"
(8)
5
/32"
(4)
GRILLE
DOOR
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
FLUSH INSET PANEL
SPACER
BACKER
DOOR DOOR
DOOR / DRAWER / GRILLE
TOP VIEWTOP VIEW
SIDE VIEW
CABINETRY
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEWTOP VIEW
5
/8"
(16)
5
/16" (8)
1
/2"
(13)
5
/16"
(8)
3
/32"
(2)
DOOR /
DRAWER
1
/2"(13)
3
/32"
(2)
5
/16"
(8)
5
/16"
(8)
5
/32"
(4)
GRILLE
DOOR
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
FLUSH INSET PANEL
SPACER
BACKER
DOOR DOOR
DOOR / DRAWER / GRILLE
1
/2"(13)
5
/16"
(8)
1
/8"
(3)
CABINETRY
GRILLE
TOP VIEWTOP VIEW
SIDE VIEW SIDE VIEW
SIDE VIEW
CABINETRY
1
/2"(13)
3
/32"
(2)
5
/16"
(8)
5
/16"
(8)
5
/32"
(4)
GRILLE
DOOR
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEWTOP VIEW
Flush Inset Panels
PANEL OFFSET
The illustrations provide panel offsets and reveals for built-in
models in a ush inset application. Refer to the chart below
for reference to the illustrations.
PANEL OFFSET
ALL REFRIGERATOR | ALL FREEZER ILLUS
Door | Grille Sides A
Grille Top C
Grille Bottom | Door Top D
Door Bottom F
OVER-AND-UNDER ILLUS
Door (hinge) | Drawer | Grille Sides A
Doors (handle) Sides (French door only) B
Grille Top C
Grille Bottom | Door Top D
Door Bottom | Drawer Top E
Drawer Bottom F
SIDE-BY-SIDE ILLUS
Doors (hinge) | Grille Sides A
Doors (handle) Sides B
Grille Top C
Grille Bottom | Door Top D
Door Bottom F
5
/16"
TOP VIEW
(8)
DOOR / DRAWER / GRILLE
BACKER
SPACER
FLUSH INSET PANEL
Illus. A
CABINETRY
GRILLE
Illus. C
DOOR
DRAWER
CABINETRY
5
/8"
(16)
5
/16"
(8)
SIDE VIEW
5
/16"
(8)
5
/16"
(8)
SIDE VIEW
TOP VIEW
DOOR DOOR
5
1
/2"
(13)
1
/2"(13)
1
/8"
(3)
3
/32"
(2)
5
/8"(16)
5
/32"
(4)
/16" (8)
1
Illus. B
DOOR
Illus. D
/8" (3)
GRILLE
DOOR /
DRAWER
SIDE VIEW
1
/4" (6)
REVEAL
5
/16"
(8)
5
/16"
(8)
SIDE VIEW
5
5
3
/16"
(8)
/32"
(4)
/32"
(2)
1
/2"(13)
3
/32"
(2)
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
28 | Sub-Zero Customer Care 800.222.7820
Illus. E
Illus. F
Page 29
BUILT-IN REFRIGERATION
Dual Installation
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom ller strip
require a dual installation kit. If a dual installation kit is not
specied, a 2"
(51) ller strip is recommended between units.
A custom ller strip is required when installing two French
door or side-by-side models. Dual installations without a
ller strip can only be accomplished using two units with
opposite hinges. Refer to the illustrations below.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care
at 800-222-7820.
For dual standard installations, panel dimensions are the
same as for single installations. Refer to the charts on pages
22–25. Panel dimensions and offsets for dual ush inset
installations are listed on the following pages.
WITHOUT FILLER STRIP
Opposite hinges.
FILLER STRIP
Same side hinges.
subzero.com/specs | 29
Page 30
BUILT-IN REFRIGERATION
H
H
H
W
AA
B
B
H
H
W
AA
A
B
H
H
H
W
H
H
H
W
W W
H
H
H
W
AA
B
B
H
H
H
W
W W
H
H
H
W
AA
A
A
H
H
H
W
H
H
H
W
W W
H
H
H
W
W W
Dual Flush Inset Panel Dimensions
H
H
AA
W
BI-36R, BI-36F
H
A
H
B
W
BI-36RG
MODEL BI-36R, BI-36RG, BI-36F
REFRIGERATOR | FREEZER W H
Flush Inset Panel 361/2" (927) 693/4" (1772)
Spacer Panel 351/8" (892) 6815/16" (1751)
Backer Panel 353/4" (908) 699/16" (1767)
GRILLE W H
Flush Inset Panel 361/2" (927) 91/4" (235)
Spacer Panel 351/8" (892) 85/16" (211)
Backer Panel 353/4" (908) 815/16" (227)
BI-36RG A B
Stiles | Rails 53/4" (146) 103/8" (264)
MODEL BI-30U, BI-30UG
REFRIGERATOR W H
Flush Inset Panel 301/2" (775) 501/8" (1273)
Spacer Panel 291/8" (740) 495/16" (1253)
Backer Panel 293/4" (756) 4915/16" (1268)
FREEZER W H
Flush Inset Panel 301/2" (775) 19" (483)
Spacer Panel 291/8" (740) 181/16" (459)
Backer Panel 293/4" (756) 1811/16" (475)
GRILLE W H
Flush Inset Panel 301/2" (775) 91/4" (235)
Spacer Panel 291/8" (740) 85/16" (211)
Backer Panel 293/4" (756) 815/16" (227)
BI-30UG A B
Stiles | Rails 53/4" (146) 51/4" (133)
H
H
H
W
BI-30U, BI-36U(ID)
B
B
W
BI-30UG, BI-36UG
H
AA
H
H
MODEL BI-36U(ID), BI-36UG
REFRIGERATOR W H
Flush Inset Panel 361/2" (927) 501/8" (1273)
Spacer Panel 351/8" (892) 495/16" (1253)
Backer Panel 353/4" (908) 4915/16" (1268)
FREEZER W H
Flush Inset Panel 361/2" (927) 19" (483)
Spacer Panel 351/8" (892) 181/16" (459)
Backer Panel 353/4" (908) 1811/16" (475)
GRILLE W H
Flush Inset Panel 361/2" (927) 91/4" (235)
Spacer Panel 351/8" (892) 85/16" (211)
Backer Panel 353/4" (908) 815/16" (227)
BI-36UG A B
Stiles | Rails 53/4" (146) 51/4" (133)
Grille panel dimensions are for standard 84"
83"
(2108) height, subtract 1" (25) from grille panel height dimensions and for
88"
(2235) height, add 4" (102). A specic panel grille must be ordered for an
83" or 88" overall unit height. For dual wide grilles, refer to page 32.
(2134) overall unit height. For
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
30 | Sub-Zero Customer Care 800.222.7820
Page 31
BUILT-IN REFRIGERATION
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEW
5
/8"
(16)
5
/16"
(8)
1
/2"
(13)
1
/2"(13)
3
/32"
(2)
5
/16"
(8)
5
/16"
(8)
5
/32"
(4)
GRILLE
DOOR
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
FLUSH INSET PANEL
SPACER
BACKER
DOOR DOOR
DOOR / DRAWER / GRILLE
TOP VIEWTOP VIEW
SIDE VIEW
CABINETRY
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEWTOP VIEW
5
/8"
(16)
5
/16" (8)
1
/2"
(13)
5
/16"
(8)
3
/32"
(2)
DOOR /
DRAWER
1
/2"(13)
3
/32"
(2)
5
/16"
(8)
5
/16"
(8)
5
/32"
(4)
GRILLE
DOOR
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
FLUSH INSET PANEL
SPACER
BACKER
DOOR DOOR
DOOR / DRAWER / GRILLE
1
/2"(13)
5
/16"
(8)
1
/8"
(3)
CABINETRY
GRILLE
TOP VIEWTOP VIEW
SIDE VIEW SIDE VIEW
SIDE VIEW
CABINETRY
1
/2"(13)
3
/32"
(2)
5
/16"
(8)
5
/16"
(8)
5
/32"
(4)
GRILLE
DOOR
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEWTOP VIEW
Dual Installation
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
DUAL FLUSH INSET PANEL OFFSET
The illustrations provide panel offsets and reveals for built-in
models in a dual ush inset application. Refer to the chart
below for reference to the illustrations.
PANEL OFFSET
ALL REFRIGERATOR | ALL FREEZER ILLUS
Door (hinge) | Grille Sides A
Door (handle) Sides B
Grille Top C
Grille Bottom | Door Top D
Door Bottom F
OVER-AND-UNDER ILLUS
Door (hinge) | Drawer | Grille Sides A
Door (handle) Sides B
Grille Top C
Grille Bottom | Door Top D
Door Bottom | Drawer Top E
Drawer Bottom F
5
/16"
TOP VIEW
(8)
DOOR / DRAWER / GRILLE
BACKER
SPACER
FLUSH INSET PANEL
Illus. A
CABINETRY
GRILLE
Illus. C
DOOR
DRAWER
CABINETRY
5
/8"
(16)
5
/16"
(8)
SIDE VIEW
5
/16"
(8)
5
/16"
(8)
SIDE VIEW
TOP VIEW
DUAL
TRIM
DOOR DOOR
5
1
/2"
(13)
1
/2"(13)
1
/8"
(3)
3
/32"
(2)
5
/8"(16)
5
/32"
(4)
/16" (8)
Illus. B
DOOR
Illus. D
1
/8" (3)
GRILLE
DOOR /
DRAWER
SIDE VIEW
1
/4" (6)
REVEAL
5
/16"
(8)
5
/16"
(8)
SIDE VIEW
5
5
3
/16"
(8)
/32"
(4)
/32"
(2)
1
/2"(13)
3
/32"
(2)
Illus. E
Illus. F
subzero.com/specs | 31
Page 32
BUILT-IN REFRIGERATION
Dual Installation
DUAL WIDE GRILLE
A dual wide grille spans the entire width of both units in a
dual installation and is a part of a dual installation kit.
For overlay and ush inset panel dimensions for the dual
wide grille, refer to the charts below. Dimensions listed are
for a standard 84"
DUAL WIDE GRILLE—OVERLAY
TWO 30" MODELS W H
Overlay Panel 601/4" (1530) 91/4" (235)
Spacer Panel 593/8" (1508) 8
Backer Panel 60" (1524) 815/16" (227)
30" AND 36" MODEL W H
Overlay Panel 661/4" (1683) 91/4" (235)
Spacer Panel 653/8" (1661) 85/16" (211)
Backer Panel 66" (1676) 815/16" (227)
TWO 36" MODELS W H
Overlay Panel 721/4" (1835) 91/4" (235)
Spacer Panel 713/8" (1813) 85/16" (211)
Backer Panel 72" (1829) 815/16" (227)
(2134) nished height.
5
/16" (211)
DUAL WIDE GRILLE—FLUSH INSET
TWO 30" MODELS W H
Flush Inset Panel 611/4" (1556) 91/4" (235)
Spacer Panel 593/8" (1508) 85/16" (211)
Backer Panel 60" (1524) 815/16" (227)
30" AND 36" MODEL W H
Flush Inset Panel 671/4" (1708) 91/4" (235)
Spacer Panel 653/8" (1661) 85/16" (211)
Backer Panel 66" (1676) 815/16" (227)
TWO 36" MODELS W H
Flush Inset Panel 731/4" (1861) 91/4" (235)
Spacer Panel 713/8" (1813) 85/16" (211)
Backer Panel 72" (1829) 815/16" (227)
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
32 | Sub-Zero Customer Care 800.222.7820
Page 33
84"
(2134)
24"
(610)
ROUT TO
3
/16" (5)
(OVER-AND-UNDER
MODELS)
OPTIONAL
TOE KICK
CUT-OUT
4" (102)
201/2"
(521)
53/4"
(146)
17/8"(48)
1" (25)
41/4" (108)
ROUT TO
1
/8"
(3)
FRONT
OF SIDE
PANEL
25/8"
(67)
MAIN
FRAME
SIDE PANEL
ROUTING
1" (25)
17/8" (48)
1
/8" (3)
1
/2" (13)
BUILT-IN REFRIGERATION
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
Side Panel
The custom side panels must be a minimum of 24" (610)
deep and
side panel to t ush against the side of the unit. Refer to
the illustrations below.
When installing a built-in unit with a custom side panel, an
accessory kit is required. Stainless steel and white enamel
side panels are available through an authorized Sub-Zero
dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.
1
/2" (13) thick. Routing will be necessary for the
Standard Handles
Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer
information, visit the nd a showroom section of our
website, subzero.com.
Refer to the chart below for standard handle lengths for
built-in models.
HANDLE LENGTH
Full Door 637/8" (1622) 453/16" (1147)
Over-and-Under Door 441/4" (1124) 371/2" (952)
30" Drawer 245/16" (633) 179/16" (447)
36" Drawer 305/16" (770) 235/8" (600)
42" Drawer 365/16" (922) 295/8" (753)
TUBULAR PRO
Side panel dimensions.
Routing detail.
subzero.com/specs | 33
Page 34
BUILT-IN REFRIGERATION
Framed Panels
FULL-SCALE TEMPLATE
OPTIONAL EXTENDED
FULL-LENGTH HANDLE
1"
(25)
1
/4" (6) FRAMED PANEL
STANDARD
FULL-LENGTH HANDLE
2"
(51)
DOOR
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3
/4" (19) PANEL
1
/2" (13) PANEL
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
Framed panel thickness.
34 | Sub-Zero Customer Care 800.222.7820
Page 35
BUILT-IN REFRIGERATION
Overlay | Flush Inset Panels
FULL-SCALE TEMPLATE
Overlay and ush inset panels must be a minimum of 5/8"
(16)
thick to support mounting the handle. Panel thickness
does not include backer and spacer panel. Mount handle
close to the opening edge of the door.
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
1"
(25)
1
/4" (6) BACKER PANEL
DOOR
DEPTH OF TUBULAR
AND PRO HANDLES
2"
(51)
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3
/4" (19) PANEL
.10" (3) SPACER PANEL
Overlay and ush inset panel thickness.
subzero.com/specs | 35
Page 36
BUILT-IN REFRIGERATION
237/8"
(606)
TO REAR OF UNIT
OVERALL WIDTH OF UNIT
1
1
/
4
"
(32)
1
1
/
2
"
(38)
1
3
/
4
"
(44)
0"
(0)
1"
(25)
2"
(51)
2
1
/
4
"
(57)
2
1
/
2
"
(63)
2
3
/
4
"
(70)
3"
(76)
3
1
/
4
"
(83)
3
1
/
2
"
(89)
1
/
4
"
(6)
1
/
2
"
(13)
3
/
4
"
(19)
3
/4"
(19) THICK
OVERLAY PANEL
(TYPICAL)
1
/4"
(6) BACKER
PANEL
1"
(25) THICK
PANEL
Overlay Application
FULL-SCALE TEMPLATE
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
90° door opening (top view).
36 | Sub-Zero Customer Care 800.222.7820
1" (25)0"
SCALE
Page 37
BUILT-IN REFRIGERATION
Flush Inset Application
24"
(610)
FULL-SCALE TEMPLATE
For panels thicker than 3/4" (19), a 90° door stop may be
required to prevent interference with adjacent cabinets.
TO BACK WALL
23/16"
(56)
ASSUMES
3
/4" (19)
FLUSH INSET
PANEL
THICKNESS
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
11/4" (32)
1" (25) THICK
PANEL
3
/4" (19) THICK
FLUSH INSET PANEL
(TYPICAL)
1
/4" (6) BACKER
PANEL
110° door opening (top view).
1" (25)0"
SCALE
subzero.com/specs | 37
Page 38
BUILT-IN REFRIGERATION
FILLER STRIP
11/4" (32)
APPROX PROFILE OF
STAINLESS STEEL WRAPPED
DOOR AND HANDLE
Dual Standard Installation
FULL-SCALE TEMPLATE
Typical framed, overlay or stainless steel dual installation
with ller strip at maximum 110° door opening. Panel thickness may require a 90° door stop.
DOOR
CLOSED
DOOR
OPEN 110°
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
1" (25)0"
SCALE
Dual standard installation (top view).
38 | Sub-Zero Customer Care 800.222.7820
Page 39
BUILT-IN REFRIGERATION
FILLER STRIP
11/2" (38)
1
/2" (13)
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
PROFILE OF
3
(19) FLUSH INSET PANEL
/4"
AND TUBULAR HANDLE
Dual Flush Inset Installation
FULL-SCALE TEMPLATE
Typical ush inset dual installation with ller strip at maximum 110° door opening. Panel thickness may require a 90°
door stop.
DOOR
CLOSED
DOOR
OPEN 110°
1" (25)0"
SCALE
Dual ush inset installation (top view).
subzero.com/specs | 39
Page 40
Page 41
PRO 48 REFRIGERATION
PRO 48 Refrigeration
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
Freshness nds unmistakable expression in the Sub-Zero
PRO 48. An 800-pound monument to food preservation—
equal parts sculpted metal design statement and culinary
secret weapon. Its vast interior, like its bold exterior, is
crafted of stainless steel. The PRO 48 is available with
or without a glass door and may be either built in or
freestanding.
PRO 48 MODELS
648PRO
648PROG
subzero.com/specs | 41
Page 42
PRO 48 REFRIGERATION
Overall Dimensions
PRO 48
141/2"
(368)
48" (1219)
HEIGHT DIMENSIONS ±
1
/2" (13)
421/8"
(1070)
301/2"
(775)
21"
(533)
84"
(2134)
4" (102)
237/8"
(606)
257/8" (657)
303/16"
(767)
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
Model 648PRO, 648PROG.
42 | Sub-Zero Customer Care 800.222.7820
23/8" (60)
303/4"
(781)
SPECIFICATIONS
INTERIOR CAPACITY R CU FT (L) F CU FT (L)
648PRO 18.4 (521) 11.7 (331)
648PROG 18.4 (521) 11.7 (331)
SHIPPING WEIGHT LB
(KG)
648PRO 860 (390)
648PROG 875 (397)
Page 43
PRO 48 REFRIGERATION
SIDE
Opening Dimensions
STANDARD | FLUSH INSTALLATION
TOP VIEW
D
OPENING
DEPTH
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
OPENING
VIEW
OPENING DIMENSIONS
H
HEIGHT
W H D
W
OPENING WIDTH
FRONT VIEW
Standard 471/2" (1206) 833/4" (2127) 24" (610)
Flush 48" (1219) 841/8" (2137) 26" (660)
For standard built-in installations, the face frame of the unit
will extend 2"
(51) beyond cabinetry. For ush installations,
the front of the face frame will be ush with surrounding
cabinetry.
subzero.com/specs | 43
Page 44
PRO 48 REFRIGERATION
Electrical
The electrical supply should be located within the shaded
area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit
interrupter (GFCI) is not recommended and may cause interruption of operation.
Installation must comply with all applicable electrical codes.
ELECTRICAL REQUIREMENTS
Electrical Supply 115 VAC, 60 Hz
Service 15 amp
Receptacle 3-prong grounding-type
7"
E
(178)
6"
(152)
751/2" (1918)
FROM FLOOR
RIGHT SIDE
OF OPENING
Plumbing
The water supply line should be located within the shaded
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self-piercing valves.
The water supply line must not interfere with installation of
the anti-tip bracket.
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi
to the unit at all times. A copper line is not recommended
for this application.
Installation must comply with all applicable plumbing codes.
PLUMBING REQUIREMENTS
Water Supply
Pressure 35–120 psi
Excess Line for Connection 36" (914)
RIGHT SIDE
OF OPENING
1
/4" OD copper, braided stainless
(2.4–8.3 bar) supplied
steel or PEX tubing
(2.4–8.3 bar)
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
Electrical supply location.
44 | Sub-Zero Customer Care 800.222.7820
53/16"
6"
(152)
3" (76)
AREA EXTENDS
FORWARD ON FLOOR
Water supply location.
(132)
1
/2" (13)
Page 45
PRO 48 REFRIGERATION
Standard Handles
Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer
information, visit the nd a showroom section of our
website, subzero.com.
Refer to the chart below for standard handle lengths for
PRO 48 models.
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
HANDLE LENGTH
Door NA 2711/16" (703)
Refrigerator Drawer NA 1915/16" (506)
Freezer Drawer NA 119/16" (294)
TUBULAR PRO
subzero.com/specs | 45
Page 46
Page 47
INTEGRATED REFRIGERATION
Integrated Refrigeration
With custom front panels and hardware, Sub-Zero invented
integrated columns, tall and drawer models that disappear
into the decor. Integrated units t ush with other cabinets,
making integrated refrigeration as practical and beautiful in
the master suite, bar or theatre room as in the kitchen.
COLUMN MODELS
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
IC-18FI
IC-24C(I)
TALL MODELS
IT-30R(ID)
IT-30FI
IT-30CI(ID)
DRAWER MODELS
IC-24R
IC-24FI
IT-36R(ID)
IT-36CI(ID)
IC-30R(ID)
IC-30FI
IC-36R(ID)
IC-36FI
ID-24R
ID-24F(I)
ID-27R
ID-30R(P)
ID-30F(I)
ID-30C(I)
ID-36R(P)
ID-36C(I)
subzero.com/specs | 47
Page 48
INTEGRATED REFRIGERATION
691/2"
(1765)
W 24" (610)
84"*
(2134)
41/2" (114)
35/8" (92)
*831/2" (2121) MIN TO 841/2" (2146) MAX
A
B
13/4" (45)
Specications
INTERIOR CAPACITY—CU FT (L)
COLUMN REFR FRZR
IC-18FI 8.4 (238)
IC-24R 12.9 (365)
IC-24FI 12.3 (348)
IC-24C(I) 8.0 (227) 3.1 (88)
IC-30R(ID) 17.3 (490)
IC-30FI 15.3 (433)
IC-36R(ID) 21.4 (606)
IC-36FI 20.0 (566)
TALL REFR FRZR
IT-30R(ID) 16.5 (467)
IT-30FI 15.1 (428)
IT-30CI(ID) 10.6 (300) 5.0 (142)
IT-36R(ID) 20.5 (580)
IT-36CI(ID) 13.3 (377) 6.4 (181)
DRAWER REFR FRZR
ID-24R 4.0 (113)
ID-24F(I) 3.8 (108)
ID-27R 4.6 (130)
ID-30R(P) 5.2 (147)
ID-30F(I) 4.9 (139)
ID-30C(I) 3.0 (85) 2.0 (57)
ID-36R(P) 6.6 (187)
ID-36C(I) 3.4 (96) 2.5 (71)
Overall Dimensions
COLUMN
SHIPPING WEIGHT
COLUMN LB (KG)
18" Column 260 (118)
24" Column 340 (154)
30" Column 400 (181)
36" Column 440 (200)
TALL LB
30" Tall 400 (181)
36" Tall 460 (209)
DRAWER LB
24" Drawer 170 (77)
27" Drawer 190 (86)
30" Drawer 210 (95)
36" Drawer 250 (113)
IMPORTANT NOTE: Overall dimensions do not include panels
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
or handles. Dimensions will vary with panel thickness.
48 | Sub-Zero Customer Care 800.222.7820
(KG)
(KG)
COLUMN
18" Column 18" (457) 21/2" (64) 161/2" (419)
W A B
24" Column 24" (610) 4" (102) 221/2" (572)
30" Column 30" (762) 55/8" (143) 281/2" (724)
36" Column 36" (914) 71/4" (184) 341/2" (876)
Page 49
INTEGRATED REFRIGERATION
183/8"
(467)
W 24" (610)
84"*
(2134)
109/16"
(268)
447/8"
(1140)
135/16"
(338)
3
/8" (10)
41/2"
(114)
35/8"
(92)
*831/2" (2121) MIN TO 841/2" (2146) MAX
3
/8" (10)
A
B
13/4" (45)
34
Overall Dimensions
TALL DRAWER
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
W
1
/2"*
(876)
*34" (864) MIN TO 35" (889) MAX
183/8"
(467)
135/16"
(338)
109/16"
(268)
24" (610)
1
(6)
/4"
3
(10)
/8"
35/8" (92)
TALL
30" Tall 30" (762) 55/8" (143) 281/2" (724)
36" Tall 36" (914) 71/4" (184) 341/2" (876)
W A B
DRAWER
24" Drawer 24" (610)
27" Drawer 27" (686)
30" Drawer 30" (762)
36" Drawer 36" (914)
subzero.com/specs | 49
W
Page 50
INTEGRATED REFRIGERATION
NOTE:
SIDE
Opening Dimensions
INTEGRATED
(635)
25"
OPENING
DEPTH
TOP VIEW
OPENING DIMENSIONS
COLUMN | TALL W* H
18" Column 18" (457) 84" (2134)
24" Column 24" (610) 84" (2134)
30" Column | Tall 30" (762) 84" (2134)
36" Column | Tall 36" (914) 84" (2134)
DRAWER W* H
24" Drawer 24" (610) 341/2" (876)
27" Drawer 27" (686) 341/2" (876)
30" Drawer 30" (762) 341/2" (876)
36" Drawer 36" (914) 341/2" (876)
*For stainless steel side panel accessory, add 1" (25) per panel to opening width.
H
OPENING
HEIGHT
VIEW
31/2" (89) finished returns will be visible and should be finished to match cabinetry.
3
/4"
(19)
31/2" (89)
FINISHED
RETURN
TYPICAL
31/2" (89)
FINISHED
RETURN
W
OPENING WIDTH
FRONT VIEW
FILLER
The depth of each integrated model is 24" (610). Allow for
panel thickness when planning the nished opening depth.
1
A minimum 3
/2" (89) nished return is required on all sides
of the opening. Framed cabinets will require additional
nished ller material behind the face frame for a proper
installation. Refer to the illustration.
DUAL INSTALLATION
When installing two units side by side in a dual installation, the opening width is the width of the two units added
together. A dual installation kit will be required for this installation. If a dual installation kit is not specied, a minimum
(51) ller strip is required between units.
2"
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care
at 800-222-7820.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
W W
FRAMELESS CABINETRY
FRAMED CABINETRY
50 | Sub-Zero Customer Care 800.222.7820
Page 51
INTEGRATED REFRIGERATION
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
Electrical
The electrical supply must be located within the shaded
area shown in the illustration and chart below. A separate
circuit, servicing only this appliance is required. A ground
fault circuit interrupter (GFCI) is not recommended and may
cause interruption of operation.
The electrical outlet must be positioned with the grounding
prong to the right of the thinner blades.
Installation must comply with all applicable electrical codes.
ELECTRICAL REQUIREMENTS
Electrical Supply 115 VAC, 60 Hz
Service 15 amp
Receptacle 3-prong grounding-type
ELECTRICAL SUPPLY LOCATION
18" Model 6" (152)
24" Model 91/2" (241)
27" Model 11" (279)
30" Model 121/2" (318)
36" Model 151/2" (394)
A
Plumbing
The water supply line should be located within the shaded
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self-piercing valves.
The water supply line must not interfere with installation of
the anti-tip bracket.
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi
to the unit at all times. A copper line is not recommended
for this application.
Installation must comply with all applicable plumbing codes.
PLUMBING REQUIREMENTS
Water Supply
Pressure 35–120 psi
Excess Line for Connection 36" (914)
WATER SUPPLY LOCATION
18" Model 3" (76)
24" Model 51/2" (140)
30" Model 6" (152)
36" Model 9" (229)
(2.4–8.3 bar) supplied
1
/4" OD copper, braided stain-
less steel or PEX tubing
(2.4–8.3 bar)
A
LEFT SIDE
OF OPENING
41/2"
(114)
1
/4" (6)1/4" (6)
A
FLOOR
Electrical supply location.
41/4"
(108)
RIGHT SIDE
OF OPENING
6" (152)
A
3" (76)
AREA EXTENDS
FORWARD ON FLOOR
1
/2" (13)
Water supply location.
subzero.com/specs | 51
Page 52
INTEGRATED REFRIGERATION
Custom Panels
For integrated models, custom door panels and handle
hardware must be provided. Refer to the panel requirements
chart and typical panel dimensions.
The thickness of the custom panel can vary. A minimum
5
/8" (16) thick panel is required, but the thickness can be
increased provided it does not exceed the weight limit. The
depth of each integrated model is 24"
(610). Allow for panel
thickness when planning the nished opening depth. Refer
to the full-scale template on page 55.
CAUTION
As reveals between cabinetry and the unit decrease,
severe nger pinching can occur while door is closing.
Finish all sides of custom panels. They will be visible when
the door/drawer is open.
D-style handles are recommended. Door handles must be
located near the edge of the panel opposite the hinge and
should be centered top to bottom. Drawer handles must
be located near the top edge of each panel. Stainless steel
tubular and pro handles are avail able through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com.
PANEL REQUIREMENTS
WEIGHT PER PANEL MAX
18" Column 45 lb (20 kg)
24" Column 60 lb (27 kg)
30" Column 75 lb (34 kg)
36" Column 75 lb (34 kg)
WEIGHT PER PANEL MAX
30" Tall (door) 50 lb (22 kg)
36" Tall (door) 60 lb (27 kg)
Drawer 15 lb (7 kg)
PANEL THICKNESS MIN
All Panels
5
/8" (16)
TYPICAL PANEL DIMENSIONS
Column
79
(2029)
7
/8"
W
Tall
493/8"
(1254)
139/16"
(345)
1611/16"
(424)
WW
Drawer
Typical panel dimensions are based on an 84" (2134) nished
1
height for column and tall models and 34
models, with a 4"
(102) toe kick and
/2" (876) for drawer
1
/8" (3) reveals. Panel
dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the
chart below for panel widths.
PANEL WIDTH
18" Model 173/4" (451)
24" Model 233/4" (603)
27" Model 263/4" (679)
30" Model 293/4" (756)
36" Model 353/4" (908)
W
DUAL INSTALLATION
For dual installations, refer to the illustration for panel
heights and the chart below for panel widths.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
52 | Sub-Zero Customer Care 800.222.7820
PANEL WIDTH
18" Model 1713/16" (452)
24" Model 2313/16" (605)
27" Model 2613/16" (681)
30" Model 2913/16" (757)
36" Model 3513/16" (910)
W
Page 53
INTEGRATED REFRIGERATION
Custom Panels
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
DOOR PANEL HEIGHT
The height of the custom door panel can extend beyond the
typical panel height, provided it does not exceed the weight
limit. Refer to the illustration below.
13/4"
(45)
A DECORATIVE VALANCE
1
/8" (3)
DOOR
PANEL
84"
(2134)
HINGE
Upper valance—column and tall (side view).
CANNOT EXTEND
BEYOND THIS PLANE
24" (610)
TO BACK OF UNIT
TOE KICK CLEARANCE
The height of the toe kick area can extend beyond the
typical toe kick height, provided it does not exceed the
dimensions in the illustration below. Toe kick heights from
(51) to 3
2"
7
/8" (98) require a reduced toe kick accessory
available through an authorized Sub-Zero dealer. For local
dealer information, visit the nd a showroom section of our
website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.
VENTED
LOUVERS
24" (610)
TO BACK OF UNIT
11/8" (29)
MAX
TOE KICK
ADJUSTMENT
A DECORATIVE TOE KICK
CANNOT EXTEND
BEYOND THIS PLANE
2" (51)*
TO
6" (152)
FROM
FLOOR
HINGE
DOOR
PANEL
**
*2" (51) to 37/8" (98) requires sales accessory.
**Column models only.
Toe kick (side view).
subzero.com/specs | 53
Page 54
INTEGRATED REFRIGERATION
Standard Handles
Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer
information, visit the nd a showroom section of our
website, subzero.com.
Refer to the chart below for standard handle lengths for
integrated models.
HANDLE LENGTH
Column Door 501/8" (1273) 483/8" (1229)
Tall Door 331/4" (845) 311/2" (800)
24" Drawer 211/4" (540) 191/2" (495)
27" Drawer 241/4" (616) 221/2" (572)
30" Drawer 271/4" (692) 251/2" (648)
36" Drawer 331/4" (845) 311/2" (800)
TUBULAR PRO
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
54 | Sub-Zero Customer Care 800.222.7820
Page 55
INTEGRATED REFRIGERATION
Maximum Door Opening
FULL-SCALE TEMPLATE
As the panel width and/or depth increases, so does the
potential for panel interference. Interference may be
minimized by utilizing the 90° door stop.
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
1
/8" (3) REVEAL
POTENTIAL
INTERFERENCE
ADJACENT
CABINETRY
3
/4" (19) PANEL
DOOR OPEN
MAXIMUM 105°
DOOR CLOSED
3
/4" (19) PANEL
1" (25)0"
SCALE
Maximum door opening (top view).
POTENTIAL INTERFERENCE
subzero.com/specs | 55
Page 56
Page 57
WINE STORAGE
Wine Storage
Wine nds a well-deserved place of honor in a Sub-Zero
wine storage unit. Every detail is designed to ensure better
wine preservation. Cherrywood-faced racks, soft lighting,
custom cabinetry if desired—Sub-Zero helps make a wine
collection an element of beauty in the home.
WINE STORAGE MODELS
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
424G
IW-18
UW-24
IW-24
424FSG
IW-30
UW-24FS
IW-30R
WS-30
BW-30
subzero.com/specs | 57
Page 58
WINE STORAGE
Overall Dimensions
MODEL 424G | UW-24
237/8" (606) 24" (610)
34"
(864)
4" (102)
253/8"
(645)
MODEL 424FSG | UW-24FS
241/4" (616) 245/8" (625)
343/16"
(868)
4" (102)
253/8"
(645)
13/4" (44)
SPECIFICATIONS
STORAGE CAPACITY BOTTLES*
424G, UW-24 46
424FSG, UW-24FS 46
SHIPPING WEIGHT LB (KG)
424G, UW-24 195 (88)
424FSG, UW-24FS 220 (100)
*750 ml bottles.
13/4" (44)
Overall dimensions for models 424G and UW-24 are
based on the stainless steel models. Refer to page 81 for
door clearance information. Freestanding models 424FSG
and UW-24FS have a nished stainless steel exterior and
handle.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
58 | Sub-Zero Customer Care 800.222.7820
Page 59
WINE STORAGE
W
OPENING WIDTH
341/2"
(876)
OPENING
HEIGHT
24" (610)
OPENING
DEPTH
TOP VIEW
SIDE VIEW FRONT VIEW
Opening Dimensions
MODEL 424G | UW-24
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
OPENING WIDTH
424G, UW-24 24" (610)
DUAL OPENING WIDTH
Two 24" Models 481/8" (1222)
Dual installation kit required.
W
W
subzero.com/specs | 59
Page 60
WINE STORAGE
691/2"
(1765)
W 24" (610)
84"*
(2134)
41/2" (114)
35/8" (92)
*831/2" (2121) MIN TO 841/2" (2146) MAX
A
B
13/4" (45)
173/4"
(451)
W 24" (610)
84"*
(2134)
109/16"
(268)
447/8"
(1140)
135/16"
(338)
3
/8" (10)
41/2"
(114)
35/8"
(92)
*831/2" (2121) MIN TO 841/2" (2146) MAX
3
/8" (10)
A
B
13/4" (45)
Overall Dimensions
COLUMN
TALL
COLUMN
IW-18 18" (457) 21/2" (64) 161/2" (419)
IW-24 24" (610) 4" (102) 221/2" (572)
IW-30 30" (762) 55/8" (143) 281/2" (724)
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
60 | Sub-Zero Customer Care 800.222.7820
W A B
TALL
W A B
IW-30R 30" (762) 55/8" (143) 281/2" (724)
IMPORTANT NOTE: Overall dimensions do not include panels
or handles. Dimensions will vary with panel thickness.
Page 61
WINE STORAGE
Specications
STORAGE CAPACITY
COLUMN BOTTLES*
IW-18 59
IW-24 102
IW-30 146
TALL REFR BOTTLES*
IW-30R 4.0 cu ft (113 L) 86
*750 ml bottles.
SHIPPING WEIGHT
COLUMN LB (KG)
IW-18 350 (159)
IW-24 410 (186)
IW-30 460 (209)
TALL LB
IW-30R 490 (222)
(KG)
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
subzero.com/specs | 61
Page 62
WINE STORAGE
NOTE:
SIDE
Opening Dimensions
INTEGRATED WINE STORAGE
(635)
25"
OPENING
DEPTH
OPENING DIMENSIONS
W* H
18" Column 18" (457) 84" (2134)
24" Column 24" (610) 84" (2134)
30" Column | Tall 30" (762) 84" (2134)
*For stainless steel side panel accessory, add 1" (25) per panel to opening width.
H
OPENING
HEIGHT
TOP VIEW
W
OPENING WIDTH
The depth of each integrated (IW) model is 24" (610). Allow
for panel thickness when planning the nished opening
1
depth. A minimum 3
/2" (89) nished return is required on all
sides of the opening. Framed cabinets will require additional
nished ller material behind the face frame for a proper
installation. Refer to the illustration.
DUAL INSTALLATION
The unit can be installed next to an integrated refrigeration
model or another integrated wine storage model in a dual
installation. When installing two units side by side, the
opening width is the width of the two units added together.
A dual installation kit will be required for this installation. If a
dual installation kit is not specied, a minimum 2"
(51) ller
strip is required between units.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care
at 800-222-7820.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
VIEW
31/2" (89) finished returns will be visible and should be finished to match cabinetry.
3
/4"
(19)
31/2" (89)
FINISHED
RETURN
W W
FRAMELESS CABINETRY
TYPICAL
FRONT VIEW
31/2" (89)
FINISHED
RETURN
FRAMED CABINETRY
62 | Sub-Zero Customer Care 800.222.7820
FILLER
Page 63
WINE STORAGE
30" (762)
84"
(2134)
4"
(102)
733/4"
(1873)
237/8"
(606)
311/4"
(796)
17"
(432)
237/8" (606)
23/8" (60)
HEIGHT DIMENSIONS ±
1
/2" (13)
263/16" (665)
Overall Dimensions
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
MODEL WS-30 | BW-30
SPECIFICATIONS
STORAGE CAPACITY BOTTLES*
WS-30 147
BW-30 146
SHIPPING WEIGHT LB (KG)
WS-30 445 (202)
BW-30 445 (202)
*750 ml bottles.
Overall dimensions are based on the stainless steel model.
1
For ush inset applications, add
dimensions.
/2" (13) to door clearance
subzero.com/specs | 63
Page 64
WINE STORAGE
NOTE: Shaded line represents profile of unit.
SIDE
Opening Dimensions
MODEL WS-30 | BW-30 STANDARD INSTALLATION
24" (610)
OPENING
DEPTH
TOP VIEW
W
OPENING WIDTH
FRONT VIEW
VIEW
833/4"
(2127)
OPENING
HEIGHT
OPENING WIDTH
WS-30 291/2" (749)
BW-30 291/2" (749)
W
If an 83" (2108) grille height is specied, the opening height
7
must be decreased by
specied, the opening height must be increased by 4"
/8" (22). If an 88" (2235) grille height is
(102).
If two units are installed side by side, refer to page 66 for
dual standard installations.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
64 | Sub-Zero Customer Care 800.222.7820
Page 65
WINE STORAGE
*3
NOTE: Shaded line represents profile of unit with
SIDE
Opening Dimensions
MODEL WS-30 | BW-30 FLUSH INSET INSTALLATION
263/16"
(665)
FLUSH
INSET
23/16"
DEPTH
(56)
FINISHED
TOP VIEW
CLEATS*
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
1
/4"
(6)
84"
(2134)
FLUSH
INSET
HEIGHT
VIEW
" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
3/4" (19) panel.
11/4"
(32)
W
FLUSH INSET WIDTH
FRONT VIEW
4" (102)
11/4"
(32)
3"
(76)*
TYPICAL
23/16"
(56)
FLUSH INSET WIDTH
WS-30 32" (813)
BW-30 32" (813)
W
Dimensions assume a 3/4" (19) panel thickness.
If an 83"
must be decreased by
(2108) grille height is specied, the ush inset height
7
/8" (22). If an 88" (2235) grille height
is specied, the ush inset height must be increased by 4"
(102)
.
If two units are installed side by side, refer to page 67 for
dual ush inset installations.
subzero.com/specs | 65
Page 66
WINE STORAGE
NOTE: Shaded line represents profile of unit.
SIDE
Opening Dimensions
MODEL WS-30 | BW-30 DUAL STANDARD INSTALLATION
24" (610)
OPENING
DEPTH
TOP VIEW
VIEW
833/4"
(2127)
OPENING
HEIGHT
OPENING WIDTH
FRONT VIEW
DUAL OPENING WIDTH
WS-30 and 30" Built-In Model 593/4" (1518)
BW-30 and 30" Built-In Model 593/4" (1518)
WS-30 and 36" Built-In Model 653/4" (1670)
BW-30 and 36" Built-In Model 653/4" (1670)
W
W
A dual installation kit will be required for this installation.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
66 | Sub-Zero Customer Care 800.222.7820
Page 67
WINE STORAGE
*3
NOTE: Shaded line represents profile of unit with
SIDE
Opening Dimensions
MODEL WS-30 | BW-30 DUAL FLUSH INSET INSTALLATION
263/16"
(665)
FLUSH
INSET
23/16"
DEPTH
(56)
TOP VIEW
FINISHED
CLEATS*
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
1
/4"
(6)
84"
(2134)
FLUSH
INSET
HEIGHT
VIEW
" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
3/4" (19) panel.
11/4"
(32)
FLUSH INSET WIDTH
FRONT VIEW
W
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
23/16"
(56)
DUAL FLUSH INSET WIDTH
WS-30 and 30" Built-In Model 621/4" (1581)
BW-30 and 30" Built-In Model 621/4" (1581)
WS-30 and 36" Built-In Model 681/4" (1734)
BW-30 and 36" Built-In Model 681/4" (1734)
W
Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.
subzero.com/specs | 67
Page 68
WINE STORAGE
Electrical
The electrical supply must be located within the shaded
area shown in the illustration for your specic model. For
integrated (IW) models, also refer to the chart. A separate
circuit, servicing only this appliance is required. A ground
fault circuit interrupter (GFCI) is not recommended and may
cause interruption of operation.
If the unit will be connected to a home security system,
allow 36"
(914) of excess wiring for proper connection.
IMPORTANT NOTE: For integrated (IW) models, the electrical
outlet must be positioned with the grounding prong to the
right of the thinner blades.
Installation must comply with all applicable electrical codes.
ELECTRICAL REQUIREMENTS
Electrical Supply 115 VAC, 60 Hz
Service 15 amp
Receptacle 3-prong grounding-type
LEFT SIDE
OF OPENING
7"
(178)
E
ELECTRICAL LOCATION—INTEGRATED
18" Model 6" (152)
24" Model 91/2" (241)
30" Model 121/2" (318)
LEFT SIDE
OF OPENING
41/2"
(114)
1
/4" (6)1/4" (6)
A
FLOOR
41/4"
(108)
Integrated models.
A
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
2"
(51)
Model 424G, UW-24.
151/2"
(394)
FLOOR
3" (76)
Model WS-30, BW-30.
68 | Sub-Zero Customer Care 800.222.7820
751/2" (1918)
FROM FLOOR
RIGHT SIDE
OF OPENING
6"
(152)
Page 69
WINE STORAGE
A
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
Custom Panels
For framed, overlay, integrated and ush inset applications,
a custom door panel must be provided. Handle hardware
must also be provided for overlay, integrated and ush
inset applications. Refer to panel requirements and custom
panel dimensions charts for your specic model and design
application.
Do not install a solid panel on a glass door unit. A solid door
is available as a sales accessory (except models WS-30 and
BW-30) and must be installed if a solid panel is being specied. Service may be required to install the door. Contact an
authorized Sub-Zero dealer for more information. Overall
dimensions are the same for glass and solid door panels.
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
Models 424FSG and UW-24FS have a nished stainless
steel exterior that is designed to be used in a freestanding
application.
Custom Panel—424G | UW-24
For models 424G and UW-24, the custom door panel will
attach directly to the door frame with screws through a
series of pre-drilled holes.
Refer to the charts for panel requirements and dimensions.
PANEL REQUIREMENTS
WEIGHT PER PANEL MAX
424G, UW-24 10 lb (5 kg)
PANEL THICKNESS MIN
424G, UW-24
OVERLAY PANEL DIMENSIONS
AA
424G, UW-24
H
A
W
5
/8" (16)
PANEL DIMENSIONS
PANEL W H
424G, UW-24 233/4" (603) 301/16" (764)
STILES | RAILS A
Minimum 21/4" (57)
DOOR CLEARANCE
Models 424G and UW-24 can be installed ush with surrounding cabinetry. Depending on the thickness of the
overlay door panel, it may be necessary to install the unit
1
/4" (6) beyond the front surface of adjacent cabinetry to
prevent interference when the door is opened to 145°. Refer
to the full-scale template on page 81.
subzero.com/specs | 69
Page 70
WINE STORAGE
Custom Panel—Integrated
For integrated (IW) models, a custom door panel and handle
hardware must be provided. Refer to the panel requirements
chart and typical panel dimensions.
Do not install a solid panel on the glass door unit. A solid
door is available as a sales accessory through an authorized
Sub-Zero dealer.
The thickness of the custom panel can vary. A minimum
5
/8" (16) thick panel is required, but the thickness can be
increased provided it does not exceed the weight limit. The
depth of each integrated model is 24"
(610). Allow for panel
thickness when planning the nished opening depth. Refer
to the full-scale template on page 55.
Finish all sides of custom panels. They will be visible when
the door/drawer is open.
PANEL REQUIREMENTS
WEIGHT PER PANEL MAX
Door Frame (column) 35 lb (16 kg)
Door Frame (tall) 25 lb (11 kg)
Drawer Panel (tall) 15 lb (7 kg)
PANEL THICKNESS MIN
All Panels
5
/8" (16)
CAUTION
As reveals between cabinetry and the unit decrease,
severe nger pinching can occur while door is closing.
D-style handles are recommended. Door handles must be
located near the edge of the panel opposite the hinge and
should be centered top to bottom. Drawer handles must
be located near the top edge of each panel. Stainless steel
tubular and pro handles are avail able through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
70 | Sub-Zero Customer Care 800.222.7820
Page 71
WINE STORAGE
Custom Panel—Integrated
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
TYPICAL PANEL DIMENSIONS
Column
7
/8"
79
(2029)
W
W
Tall
493/8"
(1254)
139/16"
(345)
1611/16"
(424)
Typical panel dimensions are based on an 84" (2134) nished
height, 4"
(102) toe kick and
1
/8" (3) reveals. Panel dimensions must be adjusted accordingly for all other installations.
Refer to the illustration for panel height and the chart below
for panel width.
DUAL INSTALLATION
For dual installations, refer to the illustration for panel height
and the chart below for panel width.
PANEL WIDTH
MODEL W
18" Model 1713/16" (452)
24" Model 2313/16" (605)
30" Model 2913/16" (757)
PANEL WIDTH
MODEL W
18" Model 173/4" (451)
24" Model 233/4" (603)
30" Model 293/4" (756)
STILES | RAILS MIN
Stiles 31/4" (83)
Top Rail 73/4" (197)
Bottom Rail (column) 91/2" (241)
Bottom Rail (tall) 41/2" (114)
subzero.com/specs | 71
Page 72
WINE STORAGE
Custom Panel—Integrated
DOOR PANEL HEIGHT
The height of the custom door panel can extend beyond the
typical panel height, provided it does not exceed the weight
limit. Refer to the illustration below.
13/4"
(45)
A DECORATIVE VALANCE
1
/8" (3)
DOOR
PANEL
84"
(2134)
HINGE
Upper valance (side view).
CANNOT EXTEND
BEYOND THIS PLANE
24" (610)
TO BACK OF UNIT
TOE KICK CLEARANCE
The height of the toe kick area can extend beyond the
typical toe kick height, provided it does not exceed the
dimensions in the illustration below. Toe kick heights from
(51) to 3
2"
7
/8" (98) require a reduced toe kick accessory
available through an authorized Sub-Zero dealer. For local
dealer information, visit the nd a showroom section of our
website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.
VENTED
LOUVERS
24" (610)
TO BACK OF UNIT
11/8" (29)
MAX
TOE KICK
ADJUSTMENT
A DECORATIVE TOE KICK
CANNOT EXTEND
BEYOND THIS PLANE
2" (51)*
TO
6" (152)
FROM
FLOOR
HINGE
DOOR
PANEL
**
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
72 | Sub-Zero Customer Care 800.222.7820
*2" (51) to 37/8" (98) requires sales accessory.
**Column models only.
Toe kick (side view).
Page 73
WINE STORAGE
AA
Custom Panel—WS-30 | BW-30
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
FRAMED
The framed application is an overlay model with framed
design features. It is not a separate model.
1
If the custom panel is thinner than
/4" (6), a ller material
must be added to achieve a proper t. If the panel is thicker
1
/4" (6), rout an edge around the panel or mount the
than
custom panel on a sheet of
1
/4" (6) thick material and insert
into the channel.
Routing, recessing and optional extended handles may be
required for nger clearance. Refer to the full-scale template
on page 82.
PANEL REQUIREMENTS
WEIGHT PER PANEL MAX
Door 75 lb (34 kg)
Grille (optional) 13 lb (6 kg)
PANEL THICKNESS MIN
Framed
1
/4" (6)
FRAMED PANEL DIMENSIONS
H
A
H
A
W
WS-30, BW-30
PANEL DIMENSIONS
FRAMED PANEL W H
Door 293/4" (756) 699/16" (1767)
Grille (optional) 293/4" (756) 815/16" (227)
STILES | RAILS A
Minimum 33/16" (81)
subzero.com/specs | 73
Page 74
WINE STORAGE
AA
Custom Panel—WS-30 | BW-30
OVERLAY
Overlay panels are typically created by combining a 3/4" (19)
custom panel, a .10"
(3) spacer panel and a
1
/4" (6) backer
panel. Refer to the illustrations below.
PANEL REQUIREMENTS
WEIGHT PER PANEL MAX
Door 75 lb (34 kg)
Grille 13 lb (6 kg)
PANEL THICKNESS MIN
Overlay
SPACER PANEL
CUSTOM PANEL
BACKER PANEL
DOOR FRAME
1
/8"
(3)
TRIM
5
/16" (8) min
GLASS
CUSTOM
3
/4"
(19)
typical
PANEL
.10" (3)
Panel assembly (cross section). Panel assembly (rear view).
1
/4" (6)
5
SPACER
PANEL
BACKER
PANEL
/8" (16)
OVERLAY PANEL DIMENSIONS
H
A
H
A
W
WS-30, BW-30
OVERLAY PANELS
DOOR W H
Overlay Panel 30" (762) 693/4" (1772)
Spacer Panel 291/8" (740) 6815/16" (1751)
Backer Panel 293/4" (756) 699/16" (1767)
GRILLE W H
Overlay Panel 30" (762) 91/4" (235)*
1
Spacer Panel 29
/8" (740) 85/16" (211)
Backer Panel 293/4" (756) 815/16" (227)
STILES | RAILS A
Minimum 31/4" (83)
*Panel height may be increased by
refer to built-in panel congurator at subzero.com/trade/panels.
Grille panel dimensions are for standard 84"
(2108)
height, subtract 1" (25) from grille panel height dimensions and for 88"
(2235)
height, add 4" (102). A specic panel grille must be ordered for an 83"
or 88" overall unit height.
7
/16" (11) to hide upper main frame. Also
(2134) overall unit height. For 83"
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
74 | Sub-Zero Customer Care 800.222.7820
Page 75
WINE STORAGE
AA
Custom Panel—WS-30 | BW-30
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
FLUSH INSET
The ush inset application is an overlay model with ush
inset panels. It is not a separate model.
The ush inset design allows custom panels to be installed
ush with adjacent cabinets. Similar to overlay, ush inset
3
panels are typically created by combining a
panel, a .10"
(3) spacer panel and a
1
/4" (6) backer panel.
/4" (19) custom
Refer to the illustrations for overlay panels on the previous
page.
3
For ush inset panels thicker than
/4" (19), a 90° door stop
may be required to prevent interference with adjacent cabinets. Refer to the full-scale template on page 85.
PANEL REQUIREMENTS
WEIGHT PER PANEL MAX
Door 75 lb (34 kg)
Grille 13 lb (6 kg)
PANEL THICKNESS MIN
Flush Inset
5
/8" (16)
FLUSH INSET PANEL DIMENSIONS
H
A
H
A
W
WS-30, BW-30
FLUSH INSET PANELS
DOOR W H
Flush Inset Panel 31" (787) 693/4" (1772)
Spacer Panel 291/8" (740) 6815/16" (1751)
Backer Panel 293/4" (756) 699/16" (1767)
GRILLE W H
Flush Inset Panel 31" (787) 91/4" (235)
Spacer Panel 291/8" (740) 85/16" (211)
Backer Panel 293/4" (756) 815/16" (227)
STILES | RAILS A
Minimum 33/4" (95)
Grille panel dimensions are for standard 84"
83"
(2108) height, subtract 1" (25) from grille panel height dimensions and for
88"
(2235) height, add 4" (102). A specic panel grille must be ordered for an
83" or 88" overall unit height.
(2134) overall unit height. For
subzero.com/specs | 75
Page 76
WINE STORAGE
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEW
5
/8"
(16)
5
/16" (8)
1
/2"
(13)
1
/2"(13)
3
/32"
(2)
5
/16"
(8)
5
/16"
(8)
5
/32"
(4)
GRILLE
DOOR
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
FLUSH INSET PANEL
SPACER
BACKER
DOOR DOOR
DOOR / DRAWER / GRILLE
TOP VIEWTOP VIEW
SIDE VIEW
CABINETRY
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEWTOP VIEW
1
/2"(13)
3
/32"
(2)
5
/16"
(8)
5
/16"
(8)
5
/32"
(4)
GRILLE
DOOR
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEWTOP VIEW
Custom Panel—WS-30 | BW-30
FLUSH INSET PANEL OFFSET
The illustrations provide panel offsets and reveals for model
WS-30 or BW-30 in a ush inset application. Refer to the
chart below for reference to the illustrations.
PANEL OFFSET
Door | Grille Sides A
Grille Top B
Grille Bottom | Door Top C
Door Bottom D
ILLUS
5
/16"
TOP VIEW
(8)
DOOR / DRAWER / GRILLE
BACKER
SPACER
FLUSH INSET PANEL
Illus. A
GRILLE
DOOR
Illus. C
CABINETRY
5
/8"
(16)
5
/16"
5
(8)
3
5
/16"
(8)
SIDE VIEW
/32"
(4)
/32"
(2)
1
/2"
(13)
1
/2"(13)
Illus. B
Illus. D
CABINETRY
GRILLE
DOOR /
DRAWER
SIDE VIEW
1
5
/16"
(3)
(8)
SIDE VIEW
5
/16"
(8)
1
/8"
3
/2"(13)
/32"
(2)
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
76 | Sub-Zero Customer Care 800.222.7820
Page 77
WINE STORAGE
AA
Custom Panel—WS-30 | BW-30
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
DUAL INSTALLATIONS
A dual installation kit may be required if two models WS-30
or a model WS-30 and built-in unit are installed side by side,
or two models BW-30 or a model BW-30 and built-in unit.
Installations without a custom ller strip require a dual installation kit. If a dual installation kit is not specied, a 2"
(51)
ller strip is recommended between units. Dual installations
without a ller strip can only be accomplished using two
units with opposite hinges. Refer to the illustrations below.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care
at 800-222-7820.
For dual standard installations, panel dimensions are the
same as for single installations. Refer to the chart on page
74. Panel dimensions and offsets for dual ush inset installations are listed on the following pages.
DUAL FLUSH INSET PANEL DIMENSIONS
H
A
H
A
W
WS-30, BW-30
DUAL FLUSH INSET PANELS
DOOR W H
Flush Inset Panel 301/2" (775) 693/4" (1772)
Spacer Panel 291/8" (740) 6815/16" (1751)
Backer Panel 293/4" (756) 699/16" (1767)
GRILLE W H
Flush Inset Panel 301/2" (775) 91/4" (235)
Spacer Panel 291/8" (740) 85/16" (211)
Backer Panel 293/4" (756) 815/16" (227)
STILES | RAILS A
Minimum 33/4" (95)
Grille panel dimensions are for standard 84"
83"
(2108) height, subtract 1" (25) from grille panel height dimensions and for
88"
(2235) height, add 4" (102). A specic panel grille must be ordered for an
83" or 88" overall unit height.
(2134) overall unit height. For
WITHOUT FILLER STRIP
Opposite hinges.
FILLER STRIP
Same side hinges.
subzero.com/specs | 77
Page 78
WINE STORAGE
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEW
5
/8"
(16)
5
/16"
(8)
1
/2"
(13)
1
/2"(13)
3
/32"
(2)
5
/16"
(8)
5
/16"
(8)
5
/32"
(4)
GRILLE
DOOR
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
FLUSH INSET PANEL
SPACER
BACKER
DOOR DOOR
DOOR / DRAWER / GRILLE
TOP VIEWTOP VIEW
SIDE VIEW
CABINETRY
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEWTOP VIEW
1
/2"(13)
3
/32"
(2)
5
/16"
(8)
5
/16"
(8)
5
/32"
(4)
GRILLE
DOOR
1
/4" (6)
REVEAL
5
/16" (8)
1
/8" (3)
DOOR DOOR
TOP VIEWTOP VIEW
Custom Panel—WS-30 | BW-30
DUAL FLUSH INSET PANEL OFFSET
The illustrations provide panel offsets and reveals for model
WS-30 or BW-30 in a dual ush inset application. Refer to
the chart below for reference to the illustrations.
PANEL OFFSET
Door (hinge) | Grille Sides A
Door (handle) Sides B
Grille Top C
Grille Bottom | Door Top D
Door Bottom E
5
/16"
CABINETRY
GRILLE
DOOR /
DRAWER
TOP VIEW
(8)
CABINETRY
5
/8"
(16)
1
5
/16"
(8)
SIDE VIEW
5
/16"
(8)
(3)
1
(13)
1
/8"
/2"
/2"(13)
DOOR DOOR
5
/16" (8)
Illus. B
Illus. D
DOOR / DRAWER / GRILLE
BACKER
SPACER
ILLUS
FLUSH INSET PANEL
Illus. A
Illus. C
1
/8" (3)
GRILLE
DOOR
TOP VIEW
DUAL
TRIM
1
/4" (6)
REVEAL
5
/16"
(8)
5
/16"
(8)
SIDE VIEW
5
/32"
(4)
1
/2"(13)
3
/32"
(2)
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
78 | Sub-Zero Customer Care 800.222.7820
Illus. E
SIDE VIEW
3
/32"
(2)
Page 79
WINE STORAGE
84"
(2134)
24" (610)
OPTIONAL
TOE KICK
CUT-OUT
4" (102)
17/8"(48)
1" (25)
ROUT TO
1
/8" (3)
FRONT
OF SIDE
PANEL
25/8"
(67)
MAIN
FRAME
SIDE PANEL
ROUTING
1" (25)
17/8" (48)
1
/8" (3)
1
/2" (13)
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
Custom Panel—WS-30 | BW-30
SIDE PANEL
The custom side panel must be a minimum of 24" (610) deep
1
/2" (13) thick. Routing will be necessary for the side
and
panel to t ush against the side of the unit. Refer to the
illustrations below.
When installing model WS-30 or BW-30 with a custom side
panel, an accessory kit is required. Stainless steel and white
enamel side panels are available through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com.
Standard Handles
Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer
information, visit the nd a showroom section of our
website, subzero.com.
Refer to the chart below for standard handle lengths for
wine storage models.
HANDLE LENGTH
424G, UW-24 Door 241/4" (616) 221/4" (572)
IW-18, IW-24, IW-30 Door 501/8" (1273) 483/8" (1229)
IW-30R Door 331/4" (845) 311/2" (800)
IW-30R Drawer 241/4" (616) 221/2" (572)
WS-30, BW-30 Door 637/8" (1622) 453/16" (1147)
TUBULAR PRO
Side panel dimensions.
Routing detail.
subzero.com/specs | 79
Page 80
WINE STORAGE
Wine Rack Wood Facing
FULL-SCALE TEMPLATE
The natural cherrywood facing on wine storage racks can
be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale
template below for prole dimensions of the wood facing
and the chart for width.
27
(21)
7
/32" (6)
/32"
1
(13)
9
/2"
23
/16"
(14)
1
(9)
/4"
(6)
/64"
7
5
/64"
(3)
/64"
(2)
11/2"
(38)
5
/8"
(16)
7
/64" (3)
27
/32"
(21)
23
/64"
(9)
9
/16"
(14)
5
/64"
(2)
WOOD FACING WIDTH
424G, UW-24 191/2" (495)
424FSG, UW-24FS 191/2" (495)
IW-18 115/8" (295)
IW-24 175/8" (448)
IW-30, IW-30R 235/8" (600)
WS-30, BW-30 249/16" (624)
W
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
IW-18, IW-24,
IW-30, IW-30R
424G, UW-24, 424FSG
UW-24FS, WS-30, BW-30
Wine rack wood facing prole.
80 | Sub-Zero Customer Care 800.222.7820
Page 81
WINE STORAGE
Door Clearance—424G | UW-24
FULL-SCALE TEMPLATE
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
To allow for a 145° door opening, the unit should extend
1
a minimum of
/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed ush, however,
there is potential for interference with the panel if the
door is opened past 90°.
UNDERCOUNTER
UNIT
DOOR CLOSED
1
/2"
(13)
ADJACENT
CABINETRY
1" (25)0"
SCALE
145° door opening (top view).
3
/4" (19) DOOR PANEL
1
/4"
(6)
1
/8" (3)
HINGE AT 145°
OPENING
(DOOR OPENS PAST 145°)
subzero.com/specs | 81
Page 82
WINE STORAGE
Framed Panel—WS-30 | BW-30
FULL-SCALE TEMPLATE
OPTIONAL EXTENDED
FULL-LENGTH HANDLE
1"
(25)
1
/4" (6) FRAMED PANEL
STANDARD
FULL-LENGTH HANDLE
2"
(51)
DOOR
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3
/4" (19) PANEL
1
/2" (13) PANEL
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
Framed panel thickness.
82 | Sub-Zero Customer Care 800.222.7820
Page 83
WINE STORAGE
Overlay | Flush Inset Panels—WS-30 | BW-30
FULL-SCALE TEMPLATE
Overlay and ush inset panels must be a minimum of 5/8"
(16)
thick to support mounting the handle. Panel thickness
does not include backer and spacer panel. Mount handle
close to the opening edge of the door.
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
1"
(25)
1
/4" (6) BACKER PANEL
DOOR
DEPTH OF TUBULAR
AND PRO HANDLES
2"
(51)
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3
/4" (19) PANEL
.10" (3) SPACER PANEL
Overlay and ush inset panel thickness.
subzero.com/specs | 83
Page 84
WINE STORAGE
237/8"
(606)
TO REAR OF UNIT
OVERALL WIDTH OF UNIT
1
1
/
4
"
(32)
1
1
/
2
"
(38)
1
3
/
4
"
(44)
0"
(0)
1"
(25)
2"
(51)
2
1
/
4
"
(57)
2
1
/
2
"
(63)
2
3
/
4
"
(70)
3"
(76)
3
1
/
4
"
(83)
3
1
/
2
"
(89)
1
/
4
"
(6)
1
/
2
"
(13)
3
/
4
"
(19)
3
/4"
(19) THICK
OVERLAY PANEL
(TYPICAL)
1
/4"
(6) BACKER
PANEL
1"
(25) THICK
PANEL
Overlay Application—WS-30 | BW-30
FULL-SCALE TEMPLATE
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
90° door opening (top view).
84 | Sub-Zero Customer Care 800.222.7820
1" (25)0"
SCALE
Page 85
WINE STORAGE
Flush Inset Application—WS-30 | BW-30
24"
FULL-SCALE TEMPLATE
For panels thicker than 3/4" (19), a 90° door stop may be
required to prevent interference with adjacent cabinets.
(610)
TO BACK WALL
23/16"
(56)
ASSUMES
3
/4" (19)
FLUSH INSET
PANEL
THICKNESS
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
11/4" (32)
1" (25) THICK
PANEL
3
/4" (19) THICK
FLUSH INSET PANEL
(TYPICAL)
1
/4" (6) BACKER
PANEL
110° door opening (top view).
1" (25)0"
SCALE
subzero.com/specs | 85
Page 86
WINE STORAGE
FILLER STRIP
11/4" (32)
APPROX PROFILE OF
STAINLESS STEEL WRAPPED
DOOR AND HANDLE
Dual Standard Installation—WS-30 | BW-30
FULL-SCALE TEMPLATE
Typical framed, overlay or stainless steel dual installation
with ller strip at maximum 110° door opening. Panel thickness may require a 90° door stop.
DOOR
CLOSED
DOOR
OPEN 110°
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
1" (25)0"
SCALE
Dual standard installation (top view).
86 | Sub-Zero Customer Care 800.222.7820
Page 87
WINE STORAGE
FILLER STRIP
11/2" (38)
1
/2" (13)
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
PROFILE OF
3
(19) FLUSH INSET PANEL
/4"
AND TUBULAR HANDLE
Dual Flush Inset Installation—WS-30 | BW-30
FULL-SCALE TEMPLATE
Typical ush inset dual installation with ller strip at maximum 110° door opening. Panel thickness may require a 90°
door stop.
DOOR
CLOSED
DOOR
OPEN 110°
1" (25)0"
SCALE
Dual ush inset installation (top view).
subzero.com/specs | 87
Page 88
Page 89
UNDERCOUNTER REFRIGERATION
Undercounter Refrigeration
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
Sub-Zero undercounter refrigeration is a helpful addition to a
master suite, bar, home ofce or media room. In the kitchen,
a high-volume ice machine is a must for entertaining. The
design exibility of these compact yet roomy units makes
them all the more welcome in any room or outdoor kitchen.
They are ready to be tted with a custom cabinet panel or
can be ordered with a stainless steel panel.
UNDERCOUNTER MODELS
UC-24R
UC-24RO
UC-24BG
ICE MACHINE MODELS
UC-24C(I)
UC-15I(P)
UC-15I(P)O
subzero.com/specs | 89
Page 90
UNDERCOUNTER REFRIGERATION
Overall Dimensions
UNDERCOUNTER
237/8" (606)
34"
(864)
253/8"
(645)
4" (102)
24" (610)
ICE MACHINE
143/4" (375) 23" (584)
335/8"
(854)
4" (102)
18"
(457)
6"
(152)
26" (660) 8"
(203)
SPECIFICATIONS
INTERIOR CAPACITY—CU FT (L) REFR FRZR
UC-24R, UC-24RO 5.7 (161)
UC-24BG 6.0 (170)
UC-24C(I) 3.6 (102) 1.1 (31)
SHIPPING WEIGHT LB
(KG)
24" Model 130 (59)
Refer to page 95 for door clearance information.
SPECIFICATIONS
STORAGE CAPACITY LB (KG)
UC-15I(P), UC-15I(P)O 26 (12)
SHIPPING WEIGHT LB
(KG)
Ice Machine 100 (45)
Model UC-15I overall dimensions do not include panel or
handle.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
90 | Sub-Zero Customer Care 800.222.7820
Page 91
UNDERCOUNTER REFRIGERATION
W
OPENING WIDTH
341/2"
(876)
OPENING
HEIGHT
24" (610)
OPENING
DEPTH
TOP VIEW
SIDE VIEW FRONT VIEW
Opening Dimensions
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
UNDERCOUNTER
DUAL INSTALLATION
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom ller strip
require a dual installation kit. If a dual installation kit is not
specied, a 2"
(51) ller strip is recommended between units.
Dual installations without a ller strip can only be accomplished using two units with opposite hinges. Refer to the
illustrations below.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care
at 800-222-7820.
OPENING WIDTH
24" Model 24" (610)
Ice Machine 151/4" (387)
DUAL OPENING WIDTH
Two 24" Models 481/8" (1222)
Dual installation kit required.
W
WITHOUT FILLER STRIP
W
Opposite hinges.
Same side hinges.
FILLER STRIP
subzero.com/specs | 91
Page 92
UNDERCOUNTER REFRIGERATION
Electrical
The electrical supply should be located within the shaded
area shown in the illustration. For ice machine models, it is
recommended that electrical supply be placed in an adjacent cabinet. A separate circuit, servicing only this appliance is required.
IMPORTANT NOTE: For outdoor models UC-24RO and
UC-15I(P)O, a ground fault circuit interrupter (GFCI) is
required to reduce the risk of electrical shock. A GFCI is not
recommended for use with other undercounter models and
may cause interruption of operation.
Installation must comply with all applicable electrical codes.
LEFT SIDE
OF OPENING
2"
151/2"
(51)
(394)
3" (76)
FLOOR
ELECTRICAL REQUIREMENTS
Electrical Supply 115 VAC, 60 Hz
Service 15 amp
Receptacle 3-prong grounding-type
Electrical supply location.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
92 | Sub-Zero Customer Care 800.222.7820
Page 93
UNDERCOUNTER REFRIGERATION
24" (610)
ROUGH
OPENING
DEPTH
Plumbing
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
The water supply line should be located within the shaded
area shown in the illustrations below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve between the supply and the
unit. Do not use self-piercing valves. A saddle valve kit is
avail able through an authorized Sub-Zero dealer. For local
dealer information, visit the nd a showroom section of our
website, subzero.com.
IMPORTANT NOTE: A reverse osmosis system can be used
provided there is constant water pressure as indicated in the
chart below at all times. A copper line is not recommended
for this application.
PLUMBING REQUIREMENTS
Water Supply
Pressure (UC-24CI) 20–100 psi
Pressure (UC-15I) 20–80 psi (1.4–5.5 bar)
Excess Line for Connection 36" (914)
1
/4" OD copper, braided stain-
less steel or PEX tubing
(1.4–6.9 bar)
ICE MACHINE DRAIN
Ice machine models can be ordered with or without a drain
pump. Models without a pump will drain water by gravity.
A drain must be installed.
The drain and inlet water tubes must be plumbed before
connecting to the ice machine. For the gravity drain, hori-
1
zontal drain lines must have a
/4" (6) per 12" (305) fall. An air
gap will likely be required between the unit and drain.
A stand pipe with a trap below is acceptable for the drain.
LEFT SIDE
OF OPENING
2"
151/2"
(51)
(394)
AREA EXTENDS
FORWARD ON FLOOR
Model UC-24CI.
1
/2" (13)
3" (76)
Ice machine.
8"
(203)
1
/2"
(13)
LOCATION OF
WATER LINE
TOP VIEW
subzero.com/specs | 93
Page 94
UNDERCOUNTER REFRIGERATION
Custom Panel
For overlay undercounter models, custom door panels and
handle hardware must be provided. Refer to the charts for
panel requirements and dimensions.
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
PANEL REQUIREMENTS
WEIGHT PER PANEL MAX
UC-24R, UC-24C(I) 20 lb (9 kg)
UC-24BG 10 lb (5 kg)
UC-15I(P) 15 lb (7 kg)
PANEL THICKNESS MIN
All Panels
5
/8" (16)
MODEL UC-24BG
For model UC-24BG, the custom door panel will attach
directly to the door frame with screws through a series of
pre-drilled holes. Refer to the illustration below.
Do not install a solid panel on a glass door unit. A solid door
is available as a sales accessory and must be installed if a
solid panel is being specied. Service may be required to
install the door. Contact an authorized Sub-Zero dealer for
more information. Overall dimensions are the same for glass
and solid door panels.
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
94 | Sub-Zero Customer Care 800.222.7820
Page 95
UNDERCOUNTER REFRIGERATION
A
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
Custom Panel
OVERLAY PANEL DIMENSIONS
H
W
UC-24R, UC-24C(I),
UC-15I(P)
PANEL DIMENSIONS
MODEL W H
24" Model 233/4" (603) 301/16" (764)
Ice Machine 15" (381) 303/8" (772)
STILES | RAILS A
UC-24BG 21/4" (57) min
AA
W
UC-24BG
DOOR CLEARANCE
Undercounter models can be installed ush with surrounding cabinetry. Depending on the thickness of the
custom door panel, it may be necessary to install the unit
1
/4" (6) beyond the front surface of adjacent cabinetry to
prevent interference when the door is opened to 145°. Refer
to the full-scale template on page 97.
H
A
Standard Handles
Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer
information, visit the nd a showroom section of our
website, subzero.com.
Refer to the chart below for standard handle lengths for
undercounter models.
HANDLE LENGTH
Undercounter 241/4" (616) 221/2" (572)
Outdoor Model NA 1511/16" (399)
TUBULAR PRO
subzero.com/specs | 95
Page 96
UNDERCOUNTER REFRIGERATION
Wine Rack Wood Facing
FULL-SCALE TEMPLATE
The natural cherrywood facing on wine storage racks can
be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale
template below for prole dimensions of the wood facing
and the chart for widths.
1
/2"
(13)
9
(14)
23
/16"
1
(9)
/4"
(6)
/64"
5
7
/64"
/64"
(3)
(2)
11/2"
(38)
5
/8"
(16)
7
/64" (3)
27
/32"
(21)
23
/64"
(9)
9
/16"
(14)
5
/64"
(2)
WOOD FACING WIDTH
UC-24BG 191/2" (495)
UC-24C(I) 191/2" (495)
W
UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN
-18, IW-24,
-30, IW-30R
424G, UW-24, 424FSG
UW-24FS, WS-30, BW-30
Wine rack wood facing prole.
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &
Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design, are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.
All other trademarks are property of their respective owners in the United States and other countries.
96 | Sub-Zero Customer Care 800.222.7820
Page 97
UNDERCOUNTER REFRIGERATION
Door Clearance—Undercounter
FULL-SCALE TEMPLATE
BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER
To allow for a 145° door opening, the unit should extend
1
a minimum of
/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed ush, however,
there is potential for interference with the panel if the
door is opened past 90°.
UNDERCOUNTER
UNIT
DOOR CLOSED
1
/2"
(13)
ADJACENT
CABINETRY
1" (25)0"
SCALE
145° door opening (top view).
3
/4" (19) DOOR PANEL
1
/4"
(6)
1
/8" (3)
HINGE AT 145°
OPENING
(DOOR OPENS PAST 145°)
subzero.com/specs | 97
Page 98
Sub-Zero Residential Limited Warranty
FOR RESIDENTIAL USE
FULL TWO YEAR WARRANTY*
For two years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be
performed by Sub-Zero factory certied service, unless otherwise specied by Sub-Zero, Inc. Service will
be provided during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For ve years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, these parts that prove to be defective in materials
or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided
by Sub-Zero under the above warranty must be performed by Sub-Zero factory certied service, unless
otherwise specied by Sub-Zero, Inc. Service will be provided during normal business hours.
LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY
For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts
that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all
connecting tubing. If the owner uses Sub-Zero factory certied service, the service provider will repair or
replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certied service, the owner must contact Sub-Zero, Inc. (using the information below) to receive repaired or
replacement parts. Sub-Zero will not reimburse the owner for parts purchased from non-certied service
or other sources.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to
products installed in any one of the fty states of the United States, the District of Columbia or the ten
provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by
negligence, accident or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.
WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF
LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specic legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Sub-Zero factory certied service nearest you, contact
Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website,
subzero.com, email us at customerservice@subzero.com or call 800-222-7820.
*Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited
60-day parts and labor warranty for cosmetic defects.
*Replacement water lters and air purication cartridges are not covered by the product warranty.
Page 99
Sub-Zero Outdoor Limited Warranty*
FOR RESIDENTIAL USE
FULL ONE YEAR WARRANTY**
For one year from the date of original installation, this Sub-Zero product warranty covers all parts and labor
to repair or replace, under normal residential use, any part of the product that proves to be defective in
materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed
by Sub-Zero factory certied service, unless otherwise specied by Sub-Zero, Inc. Service will be provided
during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For ve years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, these parts that prove to be defective in materials
or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided
by Sub-Zero under the above warranty must be performed by Sub-Zero factory certied service, unless
otherwise specied by Sub-Zero, Inc. Service will be provided during normal business hours.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to
products installed in any one of the fty states of the United States, the District of Columbia or the ten
provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by
negligence, accident or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.
WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF
LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specic legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Sub-Zero factory certied service nearest you, contact
Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website,
subzero.com, email us at customerservice@subzero.com or call 800-222-7820.
*Product must be approved for outdoor use, designated by model and serial number.
**Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited
60-day parts and labor warranty for cosmetic defects.
**Replacement water lters are not covered by the product warranty.
Page 100
SUBZERO.COM
Loading...