Sub-Zero e Series User Manual
E SERIES BUILT-IN OVENS
INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACIÓN
INSTRUCTIONS D’INSTALLATION
ISTRUZIONI PER L’INSTALLAZIONE
INSTALLATIONSANWEISUNGEN
ENGLISH 4
ESPÃNOL 22
FRANÇAIS 40
ITALIANO 58
DEUTSCH 76
3
As you follow these instruc tions, you will
notice WARNING and CAUTION symbols.
This blocked information is impor tant for the
safe and efficient installation of Wolf equipment. There are two types of potential
hazards that may occur during installation.
Another footnote we would like to identify is
IMPORTANT NOTE: This highlights information
that is especially relevant to a problem-free
installation.
signals a situation where minor injury or
product damage may occur if you do not
follow instructions.
states a hazard that may cause serious
injury or death if precautions are not
followed.
WOLF®is a registered trademark of Wolf Appliance, Inc.
CONTACT
INFORMATION
Website:
wolfappliance.com
INSTALLATION REQUIREMENTS
IMPORTANT NOTE: This installation must be
completed by a qualified technician.
IMPORTANT NOTE:
Save these Installation
Instructions for the local inspector’s use.
Please read the entire Installation Instructions prior to installation.
Installer:
please retain these instructions
for local inspector’s reference, then leave
them with the homeowner.
Homeowner:
please read and keep these
instructions for future reference and be sure
to read the entire Use & Care Information
prior to use.
IMPORTANT NOTE:
This appliance must be
installed in accordance with all local codes.
The correct voltage, frequency and amperage
must be supplied to the appliance from a dedicated, grounded circuit which is protected by a
properly sized circuit breaker or time delay
fuse. The proper voltage, frequency, and
amperage ratings are listed on the product
rating plate.
Record the model and serial numbers before
installing the built-in oven. Both numbers are
listed on the rating plate, located on the right
side of the oven trim, directly above the door.
Open the oven door to view the rating plate.
Refer to the illustration below.
WOLF E SERIES BUILT-IN OVENS
SITE PREPARATION
IMPORTANT NOTE:
A minimum 610 mm of
usable cabinet depth is required, or the back
panel of the cabinet may need to be removed
for proper installation. A minimum 635 mm of
usable cabinet depth is required for a flush
inset installation. The electrical box must be
flush with the back panel of the cabinet.
The installation opening must have a flat, level
base platform to support the oven. Single
ovens require a minimum base support of
113 kg and double ovens require a minimum
base support of 181 kg.
IMPORTANT NOTE:
Wolf built-in ovens are
designed and agency approved for installation
with Wolf cooktops, microwaves and warming
drawers only. The nominal width of the built-in
oven should match the nominal width of the
cooktop. A built-in oven cannot be installed
below a Wolf rangetop.
RATING PLATE
INFORMATION
Model Number
Serial Number
Rating plate location
Location
of rating
plate
5
WOLF E SERIES BUILT-IN OVENS
E SERIES BUILT-IN SINGLE OVENS
MODELS ICBSO30-2F/S AND
ICBSO30-2U/S
IMPORTANT NOTE:
A minimum 610 mm of
usable cabinet depth is required, or the back
panel of the cabinet may need to be removed
for proper installation. A minimum 635 mm of
usable cabinet depth is required for a flush
inset installation. The electrical box must be
flush with the back panel of the cabinet.
For ease of installation, Wolf recommends
using 838 mm wide cabinets with the E Series
single oven. A minimum 838 mm wide cabinet
is required for a flush inset installation. The
cabinet base platform must be able to support
113 kg.
Refer to the following illustrations for overall
dimensions, installation specifications and
electrical location for the E Series single oven.
The E Series single oven requires a separate,
grounded 3-wire 220-240 V AC, 50/60 Hz, 30
amp service with its own circuit breaker. Refer
to Electrical Requirements on page 16. The
oven is not supplied with an electrical plug.
IMPORTANT NOTE:
Unless you are using
cabinets deeper than 610 mm for a standard
installation or 635 mm for a flush inset installation, it is recommended that the electrical
supply be placed in an adjacent cabinet.
Choose the location shown in the installation
illustrations on pages 8–9 that best suits your
installation.
OVERALL DIMENSIONS – MODELS ICBSO30-2F/S AND ICBSO30-2U/S
Unframed Model ICBSO30-2U/S shown.
6
25 mm
708 mm
759 mm
67 mm
RIGHT SIDE VIEW
CONDUIT
CHANNEL
48 mm
603 mm
BEHIND FRAME
687 mm
TOP VIEW
48 mm
718 mm
OPEN OVEN DOOR
759 mm
32 mm
603 mm
559 mm
INSTALLATION INSTRUCTIONS
E SERIES BUILT-IN SINGLE OVENS
STANDARD INSTALLATION
IMPORTANT NOTE:
For standard installations,
a minimum 610 mm of usable cabinet depth is
required, or the back panel of the cabinet may
need to be removed for proper installation.
The electrical box must be flush with the back
panel of the cabinet.
For standard installations, the E Series built-in
oven is installed by inserting into cabinetry
from the front. The oven has a face trim on all
four sides and will overlap stiles and rails. The
trim overlaps 3 mm on the bottom, 8 mm on
the top and 19 mm on each side.
FLUSH INSET INSTALLATION
IMPORTANT NOTE:
For flush inset installations, a minimum 635 mm of usable cabinet
depth is required, or the back panel of the
cabinet may need to be removed for proper
installation. The electrical box must be flush
with the back panel of the cabinet.
The flush inset installation requires the built-in
oven to be recessed into the cabinet. A
minimum 838 mm wide and 635 mm deep
cabinet is needed if you want the front of the
oven to be flush with surrounding cabinetry.
IMPORTANT NOTE:
For flush inset installations, the inside edges of the rough opening
must be finished, as they will be exposed
when the oven door is open. These edges
should be stained instead of having a laminated surface, to avoid damage from high
temperatures during self-clean.
COMBINATION INSTALLATIONS
The Wolf E Series single oven may be installed
below a Wolf 762 mm induction, electric or gas
cooktop. Unless you are using cabinets deeper
than 610 mm for a standard installation or 635
mm for a flush inset installation, it is recommended that the electrical supply be placed in
the base cabinet to the right of the oven. The E
Series single oven may also be installed below
a Wolf 914 mm induction, electric or gas
cooktop.
A Wolf E Series single oven may be installed
next to another E Series single oven. You must
allow for a 64 mm space between the oven
rough openings. Also, a separate inner wall is
required for each oven between openings.
7
WOLF E SERIES BUILT-IN OVENS
E SERIES BUILT-IN SINGLE OVENS
E
E
127
mm
121 mm min
838 mm
RECOMMENDED CABINET WIDTH
762 mm min
95 mm min
914 mm
STANDARD
FLOOR TO
COUNTER
HEIGHT
691 mm
OPENING
HEIGHT
724 mm
OPENING WIDTH
102
mm
610 mm min
OPENING DEPTH
ELECTRICAL
LOCATION WITHIN
OPENING APPLIES
ONLY TO CABINETS
DEEPER THAN 610 mm
STANDARD INSTALLATION
Overall Oven Width 759 mm
Overall Oven Height 708 mm
Overall Oven Depth (behind frame) 603 mm
Open Door Clearance 559 mm
Recommended Cabinet Width 838 mm
Minimum Cabinet Width 762 mm
Minimum Cabinet (Opening) Depth 610 mm
Opening Width 724 mm
Opening Height 691 mm
Minimum Base Support 113 kg
STANDARD INSTALLATION – MODELS ICBSO30-2F/S AND ICBSO30-2U/S
8
838 mm
762 mm min
724 mm
OPENING WIDTH
ELECTRICAL LOCATION
WITHIN OPENING
APPLIES ONLY TO
CABINETS DEEPER
THAN 610 mm
127
mm
E
102
mm
E E
610 mm
OPENING DEPTH
691 mm
OPENING
HEIGHT
RECOMMENDED CABINET WIDTH
E
INSTALLATION INSTRUCTIONS
E SERIES BUILT-IN SINGLE OVENS
FLUSH INSET INSTALLATION
Overall Oven Width 759 mm
Overall Oven Height 708 mm
Overall Oven Depth (behind frame) 603 mm
Open Door Clearance 559 mm
Minimum Base Support 113 kg
Minimum Cabinet Width 838 mm
Minimum Flush Inset Depth 635 mm
Opening Width 724 mm
Minimum Flush Inset Width 772 mm
Opening Height 691 mm
Minimum Flush Inset Height 724 mm
FLUSH INSET INSTALLATION – MODELS ICBSO30-2F/S AND ICBSO30-2U/S
IMPORTANT
NOTE
For flush inset
installations, the
inside edges of the
rough opening
must be finished,
as they will be
exposed when the
oven door is open.
9
TOP VIEW
22 mm
610 mm
min
OPENING
DEPTH
25 mm
RECOMMENDED CABINET WIDTH
838 mm min
914 mm
635 mm
min
FLUSH
INSET
DEPTH
E
SIDE VIEW
691 mm
OPENING
HEIGHT
11 mm
724 mm
min
FLUSH
INSET
HEIGHT
724 mm
OPENING WIDTH
772 mm
FLUSH INSET WIDTH
ELECTRICAL LOCATION
WITHIN OPENING
APPLIES ONLY TO
CABINETS DEEPER
THAN 635 mm
127
mm
102
mm
E
E
E
WOLF E SERIES BUILT-IN OVENS
E SERIES BUILT-IN DOUBLE OVENS
MODELS ICBDO30-2F/S AND
ICBDO30-2U/S
IMPORTANT NOTE:
A minimum 610 mm of
usable cabinet depth is required, or the back
panel of the cabinet may need to be removed
for proper installation. A minimum 635 mm of
usable cabinet depth is required for a flush
inset installation. The electrical box must be
flush with the back panel of the cabinet.
For ease of installation, Wolf recommends
using 838 mm wide cabinets with the E Series
double oven. A minimum 838 mm wide
cabinet is required for a flush inset installation.
The cabinet base platform must be able to
support 181 kg.
Refer to the following illustrations for overall
dimensions, installation specifications and
electrical location for the E Series double oven.
The E Series double oven requires a separate,
grounded 3-wire 220-240 V AC, 50/60 Hz, 50
amp service with its own circuit breaker. Refer
to Electrical Requirements on page 16. The
oven is not supplied with an electrical plug.
OVERALL DIMENSIONS – MODELS ICBDO30-2F/S AND ICBDO30-2U/S
IMPORTANT NOTE:
Unless you are using
cabinets deeper than 610 mm for a standard
installation or 635 mm for a flush inset installation, it is recommended that the electrical
supply be placed in an adjacent cabinet.
Choose the location shown in the installation
illustrations on pages 12–13 that best suits
your installation.
Unframed Model ICBDO30-2U/S shown.
10
25 mm
1280 mm 1257 mm
759 mm
67 mm
RIGHT SIDE VIEW
CONDUIT
CHANNEL
48 mm
603 mm
BEHIND FRAME
TOP VIEW
48 mm
718 mm
OPEN OVEN DOOR
759 mm
32 mm
603 mm
559 mm
INSTALLATION INSTRUCTIONS
E SERIES BUILT-IN DOUBLE OVENS
STANDARD INSTALLATION
IMPORTANT NOTE:
For standard installations,
a minimum 610 mm of usable cabinet depth is
required, or the back panel of the cabinet may
need to be removed for proper installation.
The electrical box must be flush with the back
panel of the cabinet.
For standard installations, the E Series built-in
oven is installed by inserting into cabinetry
from the front. The oven has a face trim on all
four sides and will overlap stiles and rails. The
trim overlaps 3 mm on the bottom, 8 mm on
the top and 19 mm on each side.
FLUSH INSET INSTALLATION
IMPORTANT NOTE:
For flush inset installations, a minimum 635 mm of usable cabinet
depth is required, or the back panel of the
cabinet may need to be removed for proper
installation. The electrical box must be flush
with the back panel of the cabinet.
The flush inset installation requires the built-in
oven to be recessed into the cabinet. A
minimum 838 mm wide and 635 mm deep
cabinet is needed if you want the front of the
oven to be flush with surrounding cabinetry.
IMPORTANT NOTE:
For flush inset installations, the inside edges of the rough opening
must be finished, as they will be exposed
when the oven doors are open. These edges
should be stained instead of having a laminated surface, to avoid damage from high
temperatures during self-clean.
11
WOLF E SERIES BUILT-IN OVENS
E SERIES BUILT-IN DOUBLE OVENS
STANDARD INSTALLATION
Overall Oven Width 759 mm
Overall Oven Height 1292 mm
Overall Oven Depth (behind frame) 603 mm
Open Door Clearance 559 mm
Recommended Cabinet Width 838 mm
Minimum Cabinet Width 762 mm
Minimum Cabinet (Opening) Depth 610 mm
Opening Width 724 mm
Opening Height 1260 mm
Minimum Base Support 181 kg
STANDARD INSTALLATION – MODELS ICBDO30-2F/S AND ICBDO30-2U/S
12
838 mm
762 mm min
724 mm
OPENING WIDTH
E
610 mm min
OPENING DEPTH
1260 mm
OPENING
HEIGHT
RECOMMENDED CABINET WIDTH
1702 mm
typical
ELECTRICAL LOCATION
WITHIN OPENING
APPLIES ONLY TO
CABINETS DEEPER
THAN 610 mm
127
mm
102
mm
E
E
E
INSTALLATION INSTRUCTIONS
E SERIES BUILT-IN DOUBLE OVENS
FLUSH INSET INSTALLATION
Overall Oven Width 759 mm
Overall Oven Height 1292 mm
Overall Oven Depth (behind frame) 603 mm
Open Door Clearance 559 mm
Minimum Base Support 181 kg
Minimum Cabinet Width 838 mm
Minimum Flush Inset Depth 635 mm
Opening Width 724 mm
Minimum Flush Inset Width 772 mm
Opening Height 1260 mm
Minimum Flush Inset Height 1294 mm
FLUSH INSET INSTALLATION – MODELS ICBDO30-2F/S AND ICBDO30-2U/S
IMPORTANT
NOTE
For flush inset
installations, the
inside edges of the
rough opening
must be finished,
as they will be
exposed when the
oven doors are
open.
13
TOP VIEW
22 mm
610 mm
min
OPENING
DEPTH
25 mm
RECOMMENDED CABINET WIDTH
838 mm min
914 mm
635 mm
min
FLUSH
INSET
DEPTH
E
SIDE VIEW
1260 mm
OPENING
HEIGHT
11 mm
1294 mm
min
FLUSH
INSET
HEIGHT
1702 mm
typical
724 mm
OPENING WIDTH
772 mm min
FLUSH INSET WIDTH
ELECTRICAL LOCATION
WITHIN OPENING
APPLIES ONLY TO
CABINETS DEEPER
THAN 635 mm
127
mm
102
mm
E
E
E
WOLF E SERIES BUILT-IN OVENS
STANDARD INSTALLATION OPTIONS
E SERIES BUILT-IN SINGLE OVEN
The Wolf E Series single oven may be installed
in combination with a Wolf convection or nonconvection microwave oven with 762 mm
E Series trim kit, and a Wolf warming drawer
with E Series stainless steel drawer front or
integrated drawer front. Refer to the illustration below, and pages 6–9 for installation specifications for E Series single ovens.
Keep in mind that the size of the custom
panel for the warming drawer with integrated
drawer front will vary according to the
specific installation. Refer to the installation
instructions provided with the microwave trim
kit and warming drawer front for detailed
specifications. Dimensions will vary according
to the specific installation.
STANDARD INSTALLATION – MODELS ICBSO30-2F/S AND ICBSO30-2U/S
Single oven installed with convection microwave with 762 mm E Series trim and warming drawer with E Series stainless
steel drawer front.
14
RECOMMENDED CABINET WIDTH
838 mm
762 mm
min
699 mm
MICROWAVE
OPENING WIDTH
mm
724 mm
OVEN OPENING WIDTH
ELECTRICAL LOCATION
WITHIN OPENING
APPLIES ONLY TO
CABINETS DEEPER
THAN 610 mm
102 mm
727 mm
WARMING DRAWER
OPENING WIDTH
127
127
mm
127
mm
E
102
mm
E E
E
102 mm
511 mm
610 mm
22 mm
PLATFORM
232 mm
606 mm
min
min
min
475 mm
25 mm
691 mm
22 mm
min
51 mm
ANTI-TIP BLOCK APPLICATIONPLATFORM APPLICATION
511 mm
610 mm
min
x
51 mm
ANTI-TIP BLOCK
232 mm
606 mm
min
min
475 mm
25 mm
691 mm
60 mm
min
NOTE: Unless you are using cabinets deeper than 610 mm, it is recommended that the
electrical supply for the oven be placed in an adjacent cabinet.
STANDARD INSTALLATION OPTIONS
E SERIES BUILT-IN DOUBLE OVEN
The Wolf E Series double oven may be
installed in combination with a Wolf warming
drawer with E Series stainless steel drawer
front or integrated drawer front. Refer to the
illustration below, and pages 10–13 for installation specifications for E Series double ovens.
e
STANDARD INSTALLATION – MODELS ICBDO30-2F/S AND ICBDO30-2U/S
Keep in mind that the size of the custom
panel for the warming drawer with integrated
drawer front will vary according to the
specific installation. Refer to the installation
instructions provided with the warming drawer
front for detailed specifications. Dimensions
will vary according to the specific installation.
Double oven installed above
warming drawer with E Series stainless steel drawer front.
INSTALLATION INSTRUCTIONS
15
RECOMMENDED CABINET WIDTH
838 mm
762 mm min
E
610 mm min
22 mm
PLATFORM
232 mm
606 mm min
1260 mm
22 mm
610 mm min
51 mm x 51 mm
ANTI-TIP BLOCK
232 mm
606 mm min
ANTI-TIP BLOCK APPLICATIONPLATFORM APPLICATION
1260 mm
60 mm
ELECTRICAL LOCATION
WITHIN OPENING
APPLIES ONLY TO
CABINETS DEEPER
THAN 24" (610)
NOTE: Unless you are using cabinets deeper than 610 mm, it is recommended that th
electrical supply for the oven be placed in an adjacent cabinet.
724 mm
OVEN OPENING WIDTH
127
mm
127
mm
102 mm
727 mm
WARMING DRAWER
OPENING WIDTH
102
mm
E
E
E
WOLF E SERIES BUILT-IN OVENS
IMPORTANT
NOTE
Be aware of local
codes and ordinances when
installing your
service.
E SERIES SINGLE OVENS
Required power supply:
220-240V AC, 50/60 Hz
Maximum connected load:
5.1 kW
Total amps:
21 amps
Minimum supply wire size:
L1, N and
ground–10 AWG
E SERIES DOUBLE OVENS
Required power supply:
220-240V AC, 50/60 Hz
Maximum connected load:
8.9 kW
Refer to the wiring diagram showing the
connections for each lead to the terminal box
on the unit.
ELECTRICAL REQUIREMENTS
The complete appliance must be properly
grounded at all times when electrical
power is applied.
NOTE: Improper connection can result in
a fire hazard.
Wiring diagram
Verify that power is disconnected from
the electrical box before proceeding.
Open the terminal box to expose the screws
with corresponding numbers. Loosen the 1, 5,
and ground screws. Run the cord through the
strain relief hole and into the terminal box.
Attach the Neutral wire to the number 1
position. Line should be attached to the 5
position and attach the ground to the corresponding ground screw. After tightening the
screws, tighten down the cord strain relief and
close the cover to the terminal box without
pinching any of the wires.
16
N
L1
GROUND
INSTALLATION INSTRUCTIONS
ELECTRICAL REQUIREMENTS
With the oven positioned directly in front of
the cabinet opening, feed the properly rated
cord attached to the oven terminal box
through the opening in the cabinet platform
(where applicable). Then, depending upon
local codes, utilize one of the following techniques to connect the appliance to the electrical power supply.
INSTALLING THE OVEN
UNPACK THE OVEN
Cut the plastic straps and remove the two
V-boards. Remove the four top foam corners
and the corner posts. Remove the carton
sleeve by lifting the sleeve up and over the
appliance.
Remove all oven racks, oven rack guides and
broiler pan from inside the oven cavity. For the
double oven, be sure to do this for both the
upper and lower ovens.
Remove the four bottom corners. Use caution
as the oven is not mounted to the shipping
base. Keep the bottom foam in place when
moving or carting the oven. The bottom foam
also protects the factory-installed trim.
IMPORTANT NOTE:
Before moving the oven,
protect any finished flooring with appropriate
materials to avoid damage to the floor.
Remove and discard all packing materials,
including cardboard and tape on the outside of
the oven and inside the oven cavity.
Oven is not mounted to the shipping
base. Do not remove banding until the
oven is at the point of installation.
Do not remove the bottom foam until
oven has been positioned next to the
installation opening.
Do not lift the unit by the oven door
handle(s). This will damage the oven door
and hinges.
17
WOLF E SERIES BUILT-IN OVENS
POSITION THE OVEN
Holding the oven by the upper edge and
bottom side of the oven chassis, carefully lift
the oven up to the cabinet opening.
Resting the oven on the cabinet base platform,
slide the oven into the opening until it is
approximately 152 mm from full insertion. If
applicable, ensure that the installer supplied
cable slides through the opening in the cabinet
platform as the oven is slid into place.
IMPORTANT NOTE:
The installer supplied
cable must be placed in the recessed area
located along the right rear vertical edge of the
oven. Make sure that the cable is not trapped
between the oven and the inner cabinet wall.
Do not block the oven air exhaust located
at the bottom of the oven. Blocking the
exhaust may cause cabinet damage and
poor baking performance.
The oven is very heavy—use caution
when lifting. It is recommended that two
people lift and position the oven into the
opening. Wear gloves to protect hands
from any sharp edges.
INSTALLING THE OVEN
OVEN DOOR REMOVAL
To reduce the weight of the oven and ease
installation, removal of the oven door(s) is an
option.
To Remove Oven Door:
Open oven door all the way.
Flip down the hinge latch on each side.
Close the oven door as far as it will shut.
While holding the oven door on each side
with both hands, lift the oven door up.
Continue to push the oven door closed and
pull it away from the oven frame.
To Reinstall Oven Door:
Insert both hanger arms into the oven
frame openings.
Open the oven door. You should hear a
”click” as the door is set into place.
Move the hinge levers back to the locked
position. Ensure that the door is free to
open and close. If not, repeat the removal
and reinstallation procedures.
18
INSTALLATION INSTRUCTIONS
INSTALLING THE OVEN
MOUNT OVEN TO CABINETRY
Once the oven is fully inserted into the cabinet
opening, locate the mounting holes on the
oven side trim. There will be four mounting
holes for a single oven and six for a double
oven. Refer to the illustration below. Use a
2 mm drill bit to drill pilot holes into the
cabinet. Use the provided wood screws to
secure the oven to the cabinet through the
oven mounting holes.
OVEN OPERATION
IMPORTANT NOTE:
Prior to operating the
oven, be sure to read the entire Wolf E Series
Built-In Ovens Use & Care Information
included with the oven for important safety
information.
Unpack the box containing the oven components found in each oven cavity. Install the
oven rack guides onto the shoulder screws
located on the interior side walls of the oven.
Slide the oven racks onto the support racks
within the oven. There are three racks per
oven. Place the broiler pan and grid on a rack
within the oven, if desired.
Turn on the power supply to the oven. Set the
time of day by pressing the
SET CLOCK
touch pad, input the desired time by using the
number pads, then touch
ENTER
.
Select any of the ten cooking modes on the
control panel. Verify that the oven is coming
up to temperature. For the double oven, be
sure to verify operation of both ovens.
IMPORTANT NOTE:
A small amount of smoke
and odor may be noticed during the initial
break-in period. Refer to the Use & Care
Information for additional information.
Failure to install the mounting screws
may cause the oven to move or tip
forward during use. This may result in
damage to the oven or personal injury.
Location of mounting holes
19
CONTACT
INFORMATION
Website:
wolfappliance.com
TROUBLESHOOTING
IMPORTANT NOTE:
If the built-in oven does
not operate properly, follow these troubleshooting steps:
Verify that power is being supplied to the
oven.
Check the electrical connections to ensure
that the installation has been completed
correctly.
Follow troubleshooting procedures as
described in the Wolf E Series Built-In
Ovens Use & Care Information.
If the oven still does not work, contact a
Wolf authorized service center. Do not
attempt to repair the oven yourself. Wolf
is not responsible for service required to
correct a faulty installation.
WIRING DIAGRAM
The wiring diagram covering the control circuit
is located on the top of the oven in a sealed
plastic bag.
WOLF E SERIES BUILT-IN OVENS
IF YOU NEED SERVICE
For service in your area, contact either your
Wolf dealer or visit the Showroom Locator
section of our website, wolfappliance.com
to find the regional distributor by country.
When calling for service, you will need the
built-in oven model and serial numbers.
Both numbers are listed on the product
rating plate, located on the right side of the
oven trim, directly above the door. Open
the oven door to view the rating plate.
Refer to the illustration on page 5 for
location of the rating plate.
20
The information and images in this book are
the copyright property of Wolf Appliance, Inc.,
an affiliate of Sub-Zero, Inc. Neither this book
nor any information or images contained herein
may be copied or used in whole or in part
without the express written permission of Wolf
Appliance, Inc., an affiliate of Sub-Zero, Inc.
©Wolf Appliance, Inc. all rights reserved.
21
Cuando consulte las instrucciones que
aparecen en esta guía, encontrará símbolos de
AVISO y PRECAUCIÓN. Esta información en
recuadros es importante para instalar el
equipo de Wolf de forma segura y eficaz.
Existen dos tipos de posibles riesgos que
pueden producirse durante una instalación.
Otro tipo de anotación que es importante
resaltar es la que se incluye en NOTA
IMPORTANTE: En esta nota se resalta la
información que resulta especialmente
importante para que la instalación se
realice sin problemas.
PRECAUCIÓN
indica una situación en la que se pueden
sufrir heridas leves o provocar daños
secundarios al producto si no se siguen
las instrucciones.
AVISO
indica peligro de que se produzcan
heridas personales graves o incluso puede
provocar la muerte si no se siguen las
precauciones especificadas.
WOLF®es una marca comercial registrada de Wolf Appliance, Inc.
INFORMACIÓN
DE CONTACTO
Página Web:
www.sub-zero.eu.com
23
REQUISITOS DE INSTALACIÓN
NOTA IMPORTANTE: Esta instalación debe ser
realizada por un técnico cualificado.
NOTA IMPORTANTE:
Guarde estas instrucciones
de instalación para que el inspector local pueda
utilizarlas.
Lea las instrucciones de instalación antes de
llevar a cabo la instalación.
Instalador:
guarde estas instrucciones para
que el inspector local pueda utilizarlas como
referencia y, a continuación, entréguelas al
propietario del aparato.
Propietario:
lea y guarde estas instrucciones
para que pueda utilizarlas como referencia en
el futuro y asegúrese de leer la guía de uso y
mantenimiento antes de utilizar el aparato.
NOTA IMPORTANTE:
Este aparato debe instalarse
siguiendo todas las normativas nacionales
correspondientes. Se debe aplicar al aparato
el voltaje, la frecuencia y el amperaje adecuados
desde una instalación eléctrica resistente con
toma de tierra protegida por un fusible de retardo.
El voltaje, la frecuencia y el amperaje se muestran
en la placa de datos del producto.
Apunte la referencia del modelo y los números
de serie antes de instalar el horno integrable.
Encontrará estos números en la placa de datos,
situada en el lado derecho del borde del horno,
justo encima de la puerta. Abra la puerta del
horno para verla. Observe la siguiente ilustración.
HOR NOS INTEGRABLES SERIE E DE WOLF
PREPARACIÓN DEL
SITIO
NOTA IMPORTANTE:
Es necesario dejar un fondo
mínimo de 610 mm utilizables, si no, podría ser
necesario quitar el panel trasero del armario para
que el horno quede bien instalado. En el caso de
una instalación empotrable, es necesario dejar un
fondo mínimo de 635 mm utilizables. La caja de
conexiones debe empotrarse con el panel trasero
del armario.
La apertura de la instalación debe tener una
plataforma con una superficie nivelada y plana
para aguantar el horno. Los hornos sencillos
necesitan un apoyo de superficie mínimo de
113 kg mientras que los hornos dobles
necesitan que este apoyo sea de 181 kg.
NOTA IMPORTANTE:
Los hornos integrables
Wolf están diseñados y aprobados por el
organismo regulador correspondiente para que
se puedan instalar solamente con placas,
microondas y cajones calentadores de Wolf. El
ancho nominal del horno integrable debe coincidir
con el ancho nominal de la placa. No se puede
instalar un horno integrable debajo de una cocina
de gas de Wolf.
INFORMACIÓN
DE LA PLACA
DE DATOS
Referencia del
modelo
Número de serie
Ubicación de la placa de datos
Ubicación
de la
placa de
datos
24
HOR NOS INTEGRABLES SERIE E DE WOLF
HORNOS SENCILLOS INTEGRABLES
SERIE E
MODELOS ICBSO30-2F/S Y
ICBSO30-2U/S
NOTA IMPORTANTE:
Es necesario dejar un fondo
mínimo de 610 mm utilizables, si no, podría ser
necesario quitar el panel trasero del armario para
que el horno quede bien instalado. En el caso de
una instalación empotrable, es necesario dejar un
fondo mínimo de 635 mm utilizables. La caja de
conexiones debe empotrarse con el panel trasero
del armario.
Para facilitar la instalación, Wolf recomienda
utilizar un armario con un ancho de 838 mm
para el horno sencillo Serie E. En el caso de
una instalación empotrable, es necesario que
el armario tenga 838 mm de ancho como mínimo.
La plataforma base del armario debe aguantar un
peso de 113 kg.
Vea las siguientes ilustraciones para conocer las
medidas totales, las especificaciones de instalación
y la ubicación de los componentes eléctricos del
horno sencillo de la Serie E.
El horno sencillo de la Serie E requiere una red
eléctrica individual de 220-240 V CA, 50/60 Hz y 30
amperios, con toma a tierra, cable de tres clavijas
y con su propio cortacircuitos. Consulte la sección
Requisitos eléctricos en la página 34. El horno no
se entrega con un enchufe eléctrico.
NOTA IMPORTANTE:
A menos que utilice armarios
con un fondo superior a 610 mm para una
instalación estándar o con un fondo superior a 635
mm para una instalación empotrable, se recomienda
que la toma eléctrica se coloque en un armario
contiguo. Elija la ubicación entre las que se
muestran en las ilustraciones de instalación en las
páginas 26-27 que mejor se adapte a su instalación.
MEDIDAS TOTALES - MODELOS ICBSO30-2F/S E ICBSO30-2U/S
759 mm
25 mm
708 mm
67 mm
VISTA LATERAL DERECHA
CANAL DEL
CONDUCTO PARA
CABLES
48 mm
603 mm
DETRÁS DEL MARCO
VISTA SUPERIOR
48 mm
687 mm
718 mm
PUERTA DEL HORNO ABIERTA
759 mm
32 mm
603 mm
559 mm
25
INSTRUCCIONES DE INSTALACIÓN
HORNOS SENCILLOS INTEGRABLES
SERIE E
INSTALACIÓN ESTÁNDAR
NOTA IMPORTANTE:
Para las instalaciones
estándar, es necesario dejar un fondo mínimo
de 610 mm utilizables, si no, podría ser necesario
quitar el panel trasero del armario para que
el aparato quede bien instalado. La caja de
conexiones debe empotrarse con el panel
trasero del armario.
Para las instalaciones estándar, el horno integrable
Serie E queda instalado al insertarlo en el armario
desde la parte delantera. El horno tiene un
contramarco frontal en cada uno de los cuatro
lados que va superpuesto sobre los raíles y
montantes. El contramarco sobresale 3 mm en
la parte inferior, 8 mm en la parte superior y 19
mm a cada uno de los lados.
INSTALACIÓN EMPOTRABLE
NOTA IMPORTANTE:
Para las instalaciones
empotrables, es necesario dejar un fondo mínimo
de 635 mm utilizables, si no, podría ser necesario
quitar el panel trasero del armario para que
el aparato quede bien instalado. La caja de
conexiones debe empotrarse con el panel
trasero del armario.
La instalación empotrable exige que el horno
integrable quede bien acoplado dentro del
armario. Si desea que el frente del horno quede
empotrado respecto al mobiliario circundante,
necesitará un mueble con un ancho mínimo de
838 mm y un fondo mínimo de 635 mm.
NOTA IMPORTANTE:
En las instalaciones
empotrables, los bordes internos de la cavidad
deben estar acabados, ya que quedarán expuestos
cuando la puerta del horno esté abierta. Estos
bordes deberían estar teñidos en vez de tener
una superficie laminada con el fin de evitar que
las altas temperaturas de la limpieza automática
los dañen.
INSTALACIONES COMBINADAS
Los hornos sencillos Serie E de Wolf se pueden
instalar debajo de una vitrocerámica, una placa
de gas o de inducción de 762 mm de Wolf. A
menos que utilice armarios con un fondo superior
a 610 mm para una instalación estándar o con un
fondo superior a 635 mm para una instalación
empotrable, se recomienda que la toma eléctrica
se coloque en el armario base situado a la derecha
del horno. Los hornos sencillos Serie E también se
pueden instalar debajo de una vitrocerámica, una
placa de gas o de inducción de 914 mm de Wolf.
Además, existe la posibilidad de instalar un horno
sencillo Serie E de Wolf al lado de otro horno
sencillo Serie E. Debe dejar un espacio de 64 mm
entre las cavidades del horno. También es
necesario dejar una pared interior separada
entre las cavidades de cada uno de los hornos.
26
HOR NOS INTEGRABLES SERIE E DE WOLF
HORNOS SENCILLOS INTEGRABLES
SERIE E
E
E
127
mm
121 mm mín
838 mm
ANCHURA DE ARMARIO
RECOMENDADA
762 mm mín
95 mm mín
914 mm
ALTURA
ESTÁNDAR
DEL SUELO A
LA ENCIMERA
691 mm
ALTURA DE
LA CAVIDAD
724 mm
ANCHURA DE LA CAVIDAD
102
mm
610 mm mín
FONDO DE LA CAVIDAD
LA UBICACIÓN
ELÉCTRICA DE LA
CAVIDAD SE APLICA
SÓLO PARA
ARMARIOS CON UN
FONDO SUPERIOR A 610 mm
INSTALACIÓN ESTÁNDAR
Anchura total del horno 759 mm
Altura total del horno 708 mm
Fondo total del horno (marco posterior) 603 mm
Margen de apertura de la puerta 559 mm
Anchura del armario recomendada 838 mm
Anchura mínima del mueble 762 mm
Fondo mínimo del armario (apertura) 610 mm
Anchura de la cavidad 724 mm
Altura de la cavidad 691 mm
Soporte mínimo de la base 113 kg
INSTALACIÓN ESTÁNDAR - MODELOS ICBSO30-2F/S E ICBSO30-2U/S
838 mm
ANCHURA DE ARMARIO
610 mm
FONDO DE LA CAVIDAD
691 mm
ALTURA DE
LA CAVIDAD
RECOMENDADA
762 mm mín
724 mm
ANCHURA DE LA CAVIDAD
LA UBICACIÓN ELÉCTRICA
DE LA CAVIDAD SE
APLICA SÓLO PARA
ARMARIOS CON UN
FONDO SUPERIOR
A 610 mm
127
mm
E
102
mm
E E
E
27
INSTRUCCIONES DE INSTALACIÓN
HORNOS SENCILLOS INTEGRABLES
SERIE E
INSTALACIÓN EMPOTRABLE
Anchura total del horno 759 mm
Altura total del horno 708 mm
Fondo total del horno (marco posterior) 603 mm
Margen de apertura de la puerta 559 mm
Soporte mínimo de la base 113 kg
Anchura mínima del mueble 838 mm
Fondo mínimo de
instalación empotrable 635 mm
Anchura de la cavidad 724 mm
Anchura mínima de
instalación empotrable 772 mm
Altura de la cavidad 691 mm
Altura mínima de
instalación empotrable 724 mm
INSTALACIÓN EMPOTRABLE - MODELOS ICBSO30-2F/S E ICBSO30-2U/S
NOTA
IMPORTANTE
En las instalaciones
empotrables, los
bordes internos de la
cavidad deben estar
acabados, ya que
quedarán expuestos
cuando la puerta del
horno esté abierta.
VISTA
SUPERIOR
610 mm
mín FONDO
DE CAVIDAD
635 mm
mín FONDO
DE
INSTALACIÓN
EMPOTRABLE
VISTA
LATERAL
22 mm
691 mm
ALTURA DE
LA CAVIDAD
11 m m
724 mm
mín
ALTURA
DE
INSTALACIÓN
EMPOTRABLE
25 mm
ANCHURA DE ARMARIO RECOMENDADA
LA UBICACIÓN ELÉCTRICA
DE LA CAVIDAD SE
APLICA SÓLO PARA
ARMARIOS CON UN
FONDO SUPERIOR
A 635 mm
914 mm
838 mm mín
724 mm
ANCHURA DE LA CAVIDAD
772 mm
ANCHURA DE INSTALACIÓN
EMPOTRABLE
102
mm
127
mm
E
E
E
E
28
HOR NOS INTEGRABLES SERIE E DE WOLF
HORNOS DOBLES INTEGRABLES
SERIE E
MODELOS ICBDO30-2F/S E
ICBDO30-2U/S
NOTA IMPORTANTE:
Es necesario dejar un fondo
mínimo de 610 mm utilizables, si no, podría ser
necesario quitar el panel trasero del armario para
que el horno quede bien instalado. En el caso de
una instalación empotrable, es necesario dejar un
fondo mínimo de 635 mm utilizables. La caja de
conexiones debe empotrarse con el panel trasero
del armario.
Para facilitar la instalación, Wolf recomienda
utilizar un armario con un ancho de 838 mm
para el horno doble Serie E. En el caso de una
instalación empotrable, es necesario que el
armario tenga 838 mm de ancho como mínimo.
La plataforma base del armario debe aguantar un
peso de 181 kg.
Vea las siguientes ilustraciones para conocer las
medidas totales, las especificaciones de instalación
y la ubicación de los componentes eléctricos del
horno doble de la Serie E.
El horno doble Serie E requiere una red eléctrica
individual de 220-240 V CA, 50/60 Hz y 50
amperios, con toma a tierra, cable de tres clavijas
y con su propio cortacircuitos. Consulte la sección
Requisitos eléctricos en la página 34. El horno no
se entrega con un enchufe eléctrico.
MEDIDAS TOTALES - MODELOS ICBDO30-2F/S E ICBDO30-2U/S
NOTA IMPORTANTE:
A menos que utilice
armarios con un fondo superior a 610 mm para
una instalación estándar o con un fondo superior
a 635 mm para una instalación empotrable, se
recomienda que la toma eléctrica se coloque en
un armario contiguo. Elija la ubicación entre las
que se muestran en las ilustraciones de instalación
en las páginas 30-31 que mejor se adapte a su
instalación.
Se muestra el modelo ICBDO30-2U/S sin marco
25 mm
1280 mm 1257 mm
759 mm
67 mm
VISTA LATERAL DERECHA
CANAL DEL
CONDUCTO
PARA CABLES
48 mm
603 mm
DETRÁS DEL MARCO
VISTA SUPERIOR
48 mm
718 mm
PUERTA DEL HORNO ABIERTA
759 mm
32 mm
603 mm
559 mm
29
INSTRUCCIONES DE INSTALACIÓN
HORNOS DOBLES INTEGRABLES
SERIE E
INSTALACIÓN ESTÁNDAR
NOTA IMPORTANTE:
Para las instalaciones
estándar, es necesario dejar un fondo mínimo
de 610 mm utilizables, si no, podría ser necesario
quitar el panel trasero del armario para que
el aparato quede bien instalado. La caja de
conexiones debe empotrarse con el panel
trasero del armario.
Para las instalaciones estándar, el horno integrable
Serie E queda instalado al insertarlo en el armario
desde la parte delantera. El horno tiene un
contramarco frontal en cada uno de los cuatro
lados que va superpuesto sobre los raíles y
montantes. El contramarco sobresale 3 mm en
la parte inferior, 8 mm en la parte superior y 19
mm a cada uno de los lados.
INSTALACIÓN EMPOTRABLE
NOTA IMPORTANTE:
Para las instalaciones
empotrables, es necesario dejar un fondo mínimo
de 635 mm utilizables, si no, podría ser necesario
quitar el panel trasero del armario para que el
aparato quede bien instalado. La caja de
conexiones debe empotrarse con el panel trasero
del armario.
La instalación empotrable exige que el horno
integrable quede bien acoplado dentro del
armario. Si desea que el frente del horno quede
empotrado respecto al mobiliario circundante,
necesitará un mueble con un ancho mínimo de
838 mm y un fondo mínimo de 635 mm.
NOTA IMPORTANTE:
En las instalaciones
empotrables, los bordes internos de la cavidad
deben estar acabados, ya que quedarán expuestos
cuando las puertas del horno estén abiertas. Estos
bordes deberían estar teñidos en vez de tener
una superficie laminada con el fin de evitar que
las altas temperaturas de la limpieza automática
los dañen.
Loading...