Sub-Zero ELECTRIC COOKTOPS INSTALL GUIDE

E LECTRIC C OOKTOPS
INSTALLATION INSTRUCTIONS
As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equip­ment. There are two types of potential hazards that may occur during installation.
signals a situation where minor injury or product damage may occur if you do not follow instr
uctions.
states a hazard that may cause serious injury or death if precautions are not followed.
WOLF®is a registered trademark of Wolf Appliance Company, LLC
WOLF ELECTRIC COOKTOPS
INSTALLATION REQUIREMENTS
IMPORTANT NOTE:
Save these Installation
Instructions for the local inspector’s use.
Please read the entire Installation Instruc-
ions prior to installation.
t This installation must be completed by a
qualified technician.
Installer:
please retain these instructions for local inspector’s reference, then leave them with the homeowner.
Homeowner:
please read and keep these instructions for future reference and be sure to read the entire Use & Care Information prior to use.
IMPORTANT NOTE:
This appliance must be installed in accordance with National Electrical Codes, as well as all state, municipal and local codes. The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit which is protected by a properly sized circuit breaker or time delay fuse. The proper voltage, frequency, and amperage ratings are listed on the product rating plate.
Record the model and serial numbers before installing the cooktop. Both numbers are on the rating plate, located on the underside of the cooktop.
BEFORE YOU START
Proper installation is your responsibility. Have a qualified technician install this
ooktop. You must also assure that electri-
c cal installation is adequate and in compli­ance with all local codes and ordinances.
Installations and repairs must be performed
y a qualified or licensed contractor or
b electrician qualified or licensed by the state, province, or region where this appliance is being installed.
Make sure you have everything necessary for correct installation. It is the responsibil­ity of the installer to comply with the instal­lation clearances specified on the product rating plate. The rating plate is located on the underside of the cooktop.
Electrical ground is required; see Electrical Requirements on page 13.
Warranty service must be preformed by a Wolf authorized service center.
This cooktop is intended for indoor use.
CONTACT INFORMATION
Wolf Customer Service: 800-332-9513
Website: wolfappliance.com
Model Number
Serial Number
3
WOLF ELECTRIC COOKTOPS
D
H
E
A
B
C
F
G
SITE PREPARATION
IMPORTANT NOTE:
Installation of the Wolf
electric cooktop must meet the following
ocation requirements. All dimensions listed
l are minimum requirements for safe operation.
To eliminate the risk of burns or fire by reaching over heated surface units, c
abinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a ventilation hood that pr minimum of 5" (127) beyond dimension H on overhead cabinets.
otects horizontally a
LOCATION IN COUNTERTOP
inimum flat countertop surface. Must be
A)M
equal to or greater than cooktop width.
B)
Minimum 2" (51) wide clearance from the cooktop side edge to any combustible surface up to 18" (457) above the cooktop (noted by shaded area).
C)
Minimum 2" (51) wide clearance from the cooktop side edge to any combustible surface up to 18" (457) above the cooktop (noted by shaded area).
OVERHEAD CABINET DIMENSIONS
D)
Minimum spacing between cabinets directly over cooktop must be greater than or equal to the nominal width of the cooktop unit(s).
E)
Minimum 18" (457) vertical distance from the countertop surface to the bottom of cabinets adjacent to the cabinet directly above the cooktop unit.
F)
Minimum 24" (610) clearance between top of countertop and bottom of wood or metal cabinet which is protected by not less than
1
/4" (6) flame retardant millboard covered with not less than No. 28 MSG sheet steel, .015" (.4) stainless steel, or .024" (.6) aluminum or .02" (.5) copper. Minimum 30" (762) clearance between the top of the countertop and the bottom of an unpro­tected wood or metal cabinet.
Minimum clearances for installation
G)
Minimum 0" (0) from rear wall.
H)
Maximum 13" (330) depth of overhead cabinets dir
ectly above and within side wall
clearances.
Failure to locate the cooktop unit without the proper clearances will result in a fire hazard.
Dimensions in parentheses are in millimeters unless otherwise specified.4
INSTALLATION INSTRUCTIONS
E
133/8" (340)
CUT-OUT
WIDTH
4" (102)
FRONT OF COUNTERTOP
15"
(381)
15"
(381)
33" (838)
RECOMMENDED CABINET WIDTH
21/2"min
(64)
191/4" (489)
COOKTOP
CUT-OUT DEPTH
133/8" (340)
COOKTOP
CUT-OUT
WIDTH
191/4" (489)
COOKTOP CUT-OUT
DEPTH
21/2"min
(64)
13" max
(330)
18"
(457)
2"**
(51)
18"
(457)
2"**
(51)
24" OR 30"*
(610 or 762)
TO COUNTERTOP
NOTE: Application shown allows for installation of two 15" (381) modules side-by-side. 18" (457) recommended cabinet width for installation of single 15" (381) module. *Minimum 24" (610) from protected cabinet or 30" (762) from unprotected cabinet to countertop. **Minimum clearance from side edge of cooktop cut-out to combustible surface up to 18" (457) above countertop.
36" (914)
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
21"
(533)
OVERALL
DEPTH
15" (381)
OVERALL WIDTH
31/2" (89)
INSTALLATION SPECIFICATIONS
Wolf electric cooktops are designed to fit a standard 24" (610) deep base cabinet with a
5" (635) deep countertop. Before making the
2 countertop cut-out, verify that the cooktop will clear the side walls of the base cabinet below.
For framed models, a minimum 5
learance is required between the countertop
c
1
/2" (140)
and any combustible surface directly below the cooktop. For unframed models, a minimum 6" (152) clearance is required.
Refer to illustrations on the following pages for installation specifications for each of the Wolf electric cooktop models.
FRAMED
The illustrations below provide the overall dimensions, installation specifications and
ountertop cut-out for Model CT15E.
c
f Model CT15E is installed above cabinets, the
I electrical placement is not critical. A grounded electrical box should be located within 4' (1.2 m)
f the right rear of the cooktop. For installation
o above an oven, unless you are using cabinets deeper than 24" (610), it is recommended that the electrical supply be placed in the base cabinet to the right of the oven.
IMPORTANT NOTE:
and/or modules are installed side by side, refer to countertop cut-out dimensions on page 12.
INSTALLATION SPECIFICATIONS – MODEL CT15E
MODEL CT15E
When multiple cooktops
Overall Dimensions
MODEL CT15E
Overall Width 15" (381)
Overall Height 31/2" (89)
Overall Depth 21" (533)
Minimum Cabinet Depth 223/4" (578)
Minimum Height Clearance* 4" (102)
Cut-Out W
Cut-Out Depth 191/4" (489)
*Minimum 51/2" (140) clearance is
equir
r combustible sur
idth 13
ed between counter
face dir
3
/8" (340)
top and any
ectly below the
Countertop Cut-Out
cooktop.
1
Dimensions may vary to
±
/8" (3).
5
WOLF ELECTRIC COOKTOPS
283/8" (721)
COOKTOP CUT-OUT WIDTH
FRONT OF COUNTERTOP
33" (838)
RECOMMENDED CABINET WIDTH
30"min (762)
21/2"min
(64)
191/4" (489)
COOKTOP
CUT-OUT DEPTH
283/8" (721)
COOKTOP CUT-OUT WIDTH
30-INCH OVEN OPENING
*Minimum 24" (610) from protected cabinet or 30" (762) from unprotected cabinet to countertop. **Minimum clearance from side edge of cooktop cut-out to combustible surface up to 18" (457) above countertop.
191/4" (489)
COOKTOP CUT-OUT
DEPTH
21/2"min
(64)
24" OR 30"*
(610 or 762)
TO COUNTERTOP
18"
(457)
2"**
(51)
18"
(457)
2"**
(51)
36"(914)
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
4" (102)
10"
(254)
31/2" (89)
24"min
(610)
E
33/4"min
(95)
13" max
(330)
21"
(
533)
OVERALL
DEPTH
30" (762)
OVERALL WIDTH
31/2" (89)
FRAMED MODEL CT30E
The illustrations below provide the overall dimensions, installation specifications and
ountertop cut-out for Model CT30E.
c
or ease of installation, 33" (838) cabinets are
F recommended for installation of Model CT30E.
A Wolf 30" (762) or 36" (914) built-in single oven may be installed below Model CT30E. For this installation, unless you are using cabinets deeper than 24" (610), it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. Refer to instal­lation instructions provided with the built-in oven for additional specifications.
INSTALLATION SPECIFICATIONS – MODEL CT30E
If Model CT30E is installed above cabinets, the electrical placement is not critical. A grounded
lectrical box should be located within 4'
e (1.2 m) of the right rear of the cooktop.
IMPORTANT NOTE:
When multiple cooktop
units are installed side by side, refer to the
ountertop cut-out dimensions on page 12.
c Model CT30E can accommodate a Wolf down-
draft ventilation system. Refer to installation instructions provided with the downdraft for additional specifications.
Overall Dimensions
MODEL CT30E
Overall Width 30" (762)
Overall Height 31/2" (89)
Overall Depth 21" (533)
Minimum Cabinet Depth 223/4" (578)
Minimum Height Clearance* 4" (102)
Cut-Out W
Cut-Out Depth 191/4" (489)
*Minimum 51/2" (140) clearance is
equir
r combustible sur
idth 28
ed between counter
face dir
3
/8" (721)
top and any
ectly below the
Countertop Cut-Out
cooktop.
1
Dimensions may vary to
6
±
/8" (3).
INSTALLATION INSTRUCTIONS
4" (102)
33/4"min (95)
10"
(254)
31/2" (89)
343/8" (873)
COOKTOP CUT-OUT WIDTH
FRONT OF COUNTERTOP
21/2"min
(64)
191/4" (489)
COOKTOP
CUT-OUT DEPTH
39" (991)
RECOMMENDED CABINET WIDTH
36"min (914)
36-INCH OVEN OPENING
343/8" (873)
COOKTOP CUT-OUT WIDTH
*Minimum 24" (610) from protected cabinet or 30" (762) from unprotected cabinet to countertop. **Minimum clearance from side edge of cooktop cut-out to combustible surface up to 18" (457) above countertop.
191/4" (489)
COOKTOP CUT-OUT
DEPTH
21/2"min
(64)
24" OR 30"*
(610 or 762)
TO COUNTERTOP
18"
(457)
2"**
(51)
18"
(457)
2"**
(51)
36" (914)
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
24"min
(610)
E
13"
max
(330)
21"
(533)
O
VERALL
DEPTH
36" (914)
OVERALL WIDTH
31/2" (89)
FRAMED MODEL CT36E
The illustrations below provide the overall dimensions, installation specifications and
ountertop cut-out for Model CT36E.
c
or ease of installation, 39" (991) cabinets are
F recommended for installation of Model CT36E.
A Wolf 30" (762) or 36" (914) built-in single oven may be installed below Model CT36E. For this installation, unless you are using cabinets deeper than 24" (610), it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. Refer to instal-
If Model CT36E is installed above cabinets, the electrical placement is not critical. A grounded
lectrical box should be located within 4'
e (1.2 m) of the right rear of the cooktop.
IMPORTANT NOTE:
units are installed side by side, refer to the
ountertop cut-out dimensions on page 12.
c Model CT36E can accommodate a Wolf down-
draft ventilation system. Refer to installation instructions provided with the downdraft for
additional specifications. lation instructions provided with the built-in oven for additional specifications.
INSTALLATION SPECIFICATIONS – MODEL CT36E
When multiple cooktop
Overall Dimensions
MODEL CT36E
Overall Width 36" (914)
Overall Height 31/2" (89)
Overall Depth 21" (533)
Minimum Cabinet Depth 223/4" (578)
Minimum Height Clearance* 4" (102)
Cut-Out W
Cut-Out Depth 191/4" (489)
*Minimum 51/2" (140) clearance is
equir
r combustible sur
idth 34
ed between counter
face dir
3
/8" (873)
top and any
ectly below the
Countertop Cut-Out
cooktop.
1
Dimensions may vary to
Dimensions in parentheses are in millimeters unless otherwise specified.
±
/8" (3).
7
33" (838)
RECOMMENDED
CABINET WIDTH
30-INCH OVEN OPENING
*Minimum 24" (610) from protected cabinet or 30" (762) from unprotected cabinet to countertop. **Minimum clearance from side edge of cooktop cut-out to combustible surface up to 18" (457) above countertop.
24" OR 30"*
(610 or 762)
TO COUNTERTOP
18"
(457)
2"**
(51)
18"
(457)
2"**
(51)
36"(914)
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
283/8" (721) COOKTOP
CUT-OUT WIDTH
15/16" (49)
RADIUS
27/16" (62)
193/8" (492)
COOKTOP
CUT-OUT DEPTH
SEE COUNTERTOP
CUT-OUT BELOW
7
/16" (11) RADIUS
SEE COUNTERTOP
CUT-OUT BELOW
301/8"*
(
765
)
RECESSED AREA FOR
FLUSH MOUNT INSTALLATION ONLY
FRONT OF COUNTERTOP
19/16" (40)
211/8"* (537)
RECESSED AREA
FOR FLUSH MOUNT
INSTALLATION ONLY
*Minimum dimension, but may be exceeded by up to 1/8" (3).
RECESSED AREA FOR
FLUSH MOUNT INSTALLATION ONLY
5
/16"
(24)
7
/8"
(22) max
COUNTERTOP
PROFILE
4" (102)
10"
(254)
31/2" (89)
E
24"min
(610)
4"min (102)
13" max
(330)
21"
(533)
OVERALL
DEPTH
30" (762)
OVERALL WIDTH
4" (102)
WOLF
ELECTRIC COOKTOPS
UNFRAMED MODEL CT30EU
The illustrations below provide the overall dimensions, installation specifications and
ountertop cut-out for Model CT30EU.
c
or ease of installation, 33" (838) cabinets are
F recommended for installation of Model CT30EU.
A Wolf 30" (762) built-in single oven may be installed below Model CT30EU. For this installa­tion, unless you are using cabinets deeper than 24" (610), it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. Refer to installation instructions provided with the built-in oven for additional specifications.
INSTALLATION SPECIFICATIONS – MODEL CT30EU
If Model CT30EU is installed above cabinets, electrical placement is not critical. A grounded
lectrical box should be located within 4'
e (1.2 m) of the right rear of the cooktop.
IMPORTANT NOTE:
Unframed electric
cooktop Model CT30EU is not designed to be
nstalled in combination with other cooktops.
i
IMPORTANT NOTE:
Unframed electric cooktops cannot be installed with a downdraft ventilation system.
For Model CT30EU installation options, refer to Unframed Installations on pages 10–11.
Overall Dimensions
MODEL CT30EU
Overall Width 30" (762)
Overall Height 4" (102)
Overall Depth 21" (533)
Minimum Cabinet Depth 223/4" (578)
Minimum Height Clearance* 4" (102)
Cut-Out W
idth 28
3
/8" (721)
Cut-Out Depth 193/8" (492)
8
ed between counter
equir
r combustible sur cooktop.
Dimensions may vary to
*Minimum 6" (152) clearance is
face dir
top and any
ectly below the
1
±
/8" (3).
Countertop Cut-Out
INSTALLATION INSTRUCTIONS
361/8"* (918)
RECESSED AREA FOR
FLUSH MOUNT INSTALLATION ONLY
343/8" (873)
COOKTOP CUT-OUT WIDTH
15/16" (49)
RADIUS
FRONT OF COUNTERTOP
27/16" (62)
193/8" (492)
COOKTOP
CUT-OUT DEPTH
19/16" (40)
211/8"* (537)
RECESSED AREA
FOR FLUSH MOUNT
INSTALLATION ONLY
39" (991)
RECOMMENDED CABINET WIDTH
SEE COUNTERTOP CUT-OUT BELOW
*Minimum 24" (610) from protected cabinet or 30" (762) from unprotected cabinet to countertop. **Minimum clearance from side edge of cooktop cut-out to combustible surface up to 18" (457) above countertop.
24" OR 30"*
(610 or 762)
TO COUNTERTOP
18"
(457)
2"**
(51)
18"
(457)
2"**
(51)
36" (914)
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
7
/16" (11) RADIUS
SEE COUNTERTOP
CUT-OUT BELOW
*Minimum dimension, but may be exceeded by up to 1/8" (3).
RECESSED AREA FOR
FLUSH MOUNT INSTALLATION ONLY
5
/16"
(24)
7
/8"
(22) max
COUNTERTOP
PROFILE
36-INCH OVEN OPENING
24"min
(610)
4" (102)
10"
(254)
31/2" (89)
E
4"
min (102)
13" max
(330)
21"
(533)
OVERALL
DEPTH
36" (914)
OVERALL WIDTH
4" (102)
UNFRAMED MODEL CT36EU
The illustrations below provide the overall dimensions, installation specifications and
ountertop cut-out for Model CT36EU.
c
or ease of installation, 39" (991) cabinets are
F recommended for installation of Model CT36EU.
A Wolf 36" (914) built-in single may be installed below Model CT36EU. For this installation, unless you are using cabinets deeper than 24" (610), it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. Refer to installation instructions provided with the built-in oven for additional specifications.
If Model CT36EU is installed above cabinets, electrical placement is not critical. A grounded
lectrical box should be located within 4'
e (1.2 m) of the right rear of the cooktop.
IMPORTANT NOTE:
cooktop Model CT36EU is not designed to be
nstalled in combination with other cooktops.
i
IMPORTANT NOTE:
cooktops cannot be installed with a downdraft ventilation system.
For Model CT36EU installation options, refer to Unframed Installations on pages 10–11.
INSTALLATION SPECIFICATIONS – MODEL CT36EU
Unframed electric
Unframed electric
Overall Dimensions
MODEL CT36EU
Overall Width 36" (914)
Overall Height 4" (102)
Overall Depth 21" (533)
Minimum Cabinet Depth 223/4" (578)
Minimum Height Clearance* 4" (102)
Cut-Out W
idth 34
3
/8" (873)
Cut-Out Depth 193/8" (492)
ed between counter
equir
r combustible sur cooktop.
Dimensions may vary to
Dimensions in parentheses are in millimeters unless otherwise specified.
*Minimum 6" (152) clearance is
top and any
ectly below the
face dir
1
±
/8" (3).
Countertop Cut-Out
9
WOLF ELECTRIC COOKTOPS
UNFRAMED INSTALLATIONS
FLUSH MOUNT INSTALLATION
Flush mount installations are intended for granite, solid surface or stone coun­tertop surfaces only. Failure to use high heat resistant surface will result in coun­tertop damage if hot cooking utensils are accidentally moved off the cooking surface.
MODELS CT30EU AND CT36EU
Unframed electric cooktop Models CT30EU and CT36EU can be mounted flush with the top of the countertop or as a frameless installation with the glass mounted on top of the counter­top surface.
IMPORTANT NOTE:
The materials required for a flush mount installation are provided with the unframed Models CT30EU and CT36EU. Refer to the instructions provided with the unframed cooktop installation package (part #806299) for additional specifications.
here are two options for a flush mount
T installation of the unframed electric cooktop; Option 1 and Option 2.
OPTION 1:
For this flush mount installation, a
recessed area surrounding the standard coun-
ertop cut-out is required. Fabrication of the
t recessed area must take place before the final countertop installation. A template of the coun­tertop cut-out is provided with the unframed cooktop for fabrication purposes.
IMPORTANT NOTE:
This fabrication method is not recommended for molded backsplash style countertops (triple cove).
For countertop cut-out dimensions, refer to the Installation Specifications illustration on page 8 for Model CT30EU and page 9 for Model CT36EU.
In order to rout the required recessed area for this flush mount installation, a second template must be made from 1/2" (13) plywood. The template will be used as a guide for a top bearing router bit.
Make the wood template wide enough so that clamps used to hold this template to the coun­tertop do not interfere with the router base. The cut-out dimension of the wood template should match the outer perimeter of the template supplied with the cooktop.
Center the wood template over the existing cut-out in the countertop and clamp. It may be helpful to use medium-strength double-sided tape to adher
e the template to the countertop; this will keep the template from shifting during the routing operation. Make sure that the adhesive can be easily removed by testing it on a scrap piece of the counter
top. Using a top bearing router bit with the wood template as a guide, rout out a the counter
5
/16" (8) deep recessed area in
top cut-out.
Dimensions in parentheses are in millimeters unless otherwise specified.10
INSTALLATION INSTRUCTIONS
7
/8" (22)
5
/16"(8)
L-Shaped
Brackets
UNFRAMED INSTALLATIONS
FLUSH MOUNT INSTALLATION
PTION 2: For this flush mount installation,
O
the countertop cut-out will be the same size as the outer edge of the glass top. It is recom-
ended that cooktop itself be used as the
m template for the cut-out. Turn the cooktop over and mark the opening using the glass top as a template.
It will be necessary to attach L-shaped brackets or cleats to the inner perimeter of the cut-out to support the cooktop. The top edge of the bracket can be no wider than
5
be attached
/16" (8) below the surface of the
7
/8" (22) and will
countertop. Refer to the illustration below. Attachment of the brackets is up to the installer's discretion, wherever enough coun­tertop material is present. Refer to the instruc­tions provided with the unframed cooktop installation kit (#806299) for additional specifi­cations.
For additional support in the cut-out area, adhere scrap countertop material to the bottom side of the countertop. Consult your countertop supplier for the proper methods of attachment.
FRAMELESS INSTALLATION
nframed electric cooktop Models CT30EU
U and CT36EU can be installed as a frameless application, with the glass mounted on top of
he countertop surface. For countertop cut-out
t dimensions, refer to the Installation Specifica­tions illustration on page 8 for Model CT30EU and page 9 for Model CT36EU.
Flush mount installation brackets
11
WOLF ELECTRIC COOKTOPS
21/2"min
(64)
FRONT OF COUNTERTOP
191/4"
(489)
CUT-OUT
DEPTH
291/4" (743)
TWO MODULES WIDTH
441/2" (1130) THREE MODULES WIDTH OR
441/4" (1124) 30" COOKTOP AND ONE MODULE
593/4" (1518) FOUR MODULES WIDTH OR
591/2" (1511) 30" COOKTOP AND TWO MODULES OR
501/4" (1276) 36" COOKTOP AND ONE MODULE
14"
(356)
CUT-OUT
WIDTH
ACCESSORIES
Optional acces­sories are available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance.com.
MULTIPLE COOKTOP INSTALLATION
If the framed electric cooktop is to be used with any combination of additional cooktop
nits or modules with a filler strip, the cut-out
u width is calculated by adding the correspon­ding units' cut-out dimensions plus 1
or each additional unit. For Model CT15E, the
f cut-out width should be increased from 13
1
/4" (32)
3
/8" (340) to 14" (356) when installed with multiple units. Refer to the illustration below.
IMPORTANT NOTE:
Unframed electric cooktops Models CT30EU and CT36EU are not designed to be installed in combination with other cooktop units.
IMPORTANT NOTE:
When multiple units are installed side by side, each unit must have its own separate recommended electrical circuit.
When two or more modules are installed together, an integrated module filler strip (IFILLER) is required. If a downdraft ventilation system is also installed, an integrated module support for downdraft ventilation (ISUPPORT) is also required. Contact your Wolf dealer for information on these accessory components.
VENTILATION OPTIONS
IMPORTANT NOTE:
It is recommended that
you operate the Wolf electric cooktop with
ither a Wolf cooktop ventilation hood, down-
e draft system or Pro ventilation hood. Contact your Wolf dealer for details.
Cooktop Wall Hood –
idths in classic stainless steel.
w
Cooktop Island Hood –
30" (762) or 36" (914)
42" (1067) width in
classic stainless steel.
Downdraft Ventilation System –
30" (762) or 36" (914) widths, with top cover and control panel in classic, platinum and carbon stainless steel finishes. Not for use with Model CT30EU or Model CT36EU.
Pro Wall Hood –
22" (559), 24" (610) or 27" (686) depths and 30" (762) to 66" (1676) widths in classic stainless steel.
Pro Island Hood –
36" (914) to 66" (1676)
widths in classic stainless steel.
Pro Hood Liner –
available in widths to
accommodate 30" (762) to 60" (1524) hoods.
All hoods have welded seams, sealed halogen lighting and removable, dishwasher-safe filters.
Countertop cut-out dimensions for installation of multiple cooktops
12
Blower requirements may vary due to the length of ducting and number of angles. The basic recommendation is 1 CFM per 100 Btu/hr
/hr). Always consult
(1 kW equals 3,415 Bt
u your HVAC professional for more concise blower r
IMPORTANT NOTE:
equirements.
When installing a ventila­tion hood, refer to the specific requirements of the hood for the minimum dimension to countertop.
INSTALLATION INSTRUCTIONS
ELECTRICAL REQUIREMENTS
Verify that power is disconnected from the electrical box before proceeding.
The cooktop is provided with a 4' (1.2 m) conduit consisting of two insulated hot lead
onductors (copper) and one insulated ground
c conductor (copper).
REQUIRED POWER SUPPLY
15" (381) Electric Cooktop
240 V AC / 60 Hz / 15 amp service 208 V AC / 60 Hz / 15 amp service
30" (762) Electric Cooktops
240 V AC / 60 Hz / 40 amp service 208 V AC / 60 Hz / 30 amp service
36" (914) Electric Cooktops
240 V AC / 60 Hz / 50 amp service 208 V AC / 60 Hz / 40 amp service
MAXIMUM CONNECTED LOAD
15" (381) Electric Cooktop
3.4 Kw at 240 V AC
2.6 Kw at 208 V AC
30" (762) Electric Cooktops
6.8 Kw at 240 V AC
5.2 Kw at 208 V AC
36" (914) Electric Cooktops
9.4 Kw at 240 V AC
7.1 Kw at 208 VAC
For Electrical Installation
– attach the
conductors to the residence wiring in accor-
ance with National Electrical Codes and all
d state, provincial, municipal and local codes.
The complete appliance must be properly grounded at all times when electrical power is applied.
Do not ground the appliance with the neutral (white) house supply wire. A separate ground wire must be utilized.
If aluminum house supply wiring is utilized, splice the appliance copper wire to the aluminum house wiring using special connectors designed and agency certified for joining copper and aluminum. Follow the connector manu­facturer's recommended procedure care­fully. Improper connection can result in a fire hazard!
IMPORTANT NOTE
This appliance must be installed in accordance with National Electrical Codes, as well as all state, municipal and local codes.
The Wolf electric cooktop requires a separate,
ounded 3-wire ser
gr
Locate the electrical supply within the
breaker
.
vice with its own circuit
shaded area shown in the Installation Specifi­cations illustration for your specific model on
9.
pages 5
This appliance must be installed in accordance with National Electrical Codes, as well as all state, municipal and local codes. The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit which is protected by a properly sized circuit breaker or time delay fuse. The proper voltage, frequency and amperage ratings are listed on the product rating plate, located on the underside of the cooktop.
Dimensions in parentheses are in millimeters unless otherwise specified.
13
WOLF ELECTRIC COOKTOPS
COOKTOP
FOAM STRIP
COOKTOP
COUNTERTOP
BRACKET
SCREWS
BRACKET
31/2" (89)
CLAMPING
SCREW
COOKTOP INSTALLATION
Attach the foam strip to the underside of the cooktop frame. Refer to the illustration below.
IMPORTANT NOTE:
ions, adhere the foam strip to the outer edge
t
For frameless installa-
of the glass, not the support frame.
IMPORTANT NOTE:
The materials required for a flush mount installation are provided with the unframed Models CT30EU and CT36EU. Refer to the instructions provided with the unframed cooktop installation kit (#806299).
Gently lower the unit into the cut-out area in the countertop and center. Check that the front edge of cooktop is parallel to the front edge of the countertop. Check that all required clear­ances are met.
Attach the brackets to the bottom of the unit, as shown in the illustration below. Install the clamping screws into the bracket and tighten until the screws contact the underside of the countertop.
IMPORTANT NOTE:
Do not overtighten the screws.
Do not seal the cooktop to the countertop. It must be removed if service is necessary.
If the glass ceramic top of the cooktop is broken, turn off power to the unit. Do not operate until glass has been replaced by a Wolf authorized service center.
BEFORE OPERATING THE COOKTOP
Clean the glass ceramic surface carefully using the Cooktop Cleaning Crème provided with the
ooktop. Remove all cleaning residue.
c
ead the entire Wolf Electric Cooktops Use
R & Care Information included with the cooktop. Important safety, service and warranty
nformation is contained within the book.
i
COOKTOP REMOVAL
IMPORTANT NOTE:
This procedure should only be performed by a Wolf authorized service center.
If it is necessary to remove the cooktop for cleaning or service, disconnect the electrical supply. Remove the mounting brackets on the right and left side of the unit and remove the cooktop. Reinstall in the reverse order.
IMPORTANT NOTE:
For flush mount installa­tions, use a razor blade to carefully cut around the RTV perimeter seal. A new RTV installation kit (#806299) will be required to reinstall the cooktop. This kit is available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance.com.
14
Foam strip Installation brackets
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING
IF COOKTOP DOES NOT OPERATE
MPORTANT NOTE:If the electric cooktop
I
does not operate properly, follow these troubleshooting steps:
Verify that power is being supplied to the cooktop.
Check electrical connections to ensure that the installation has been completed correctly.
Follow troubleshooting procedures as described in the Wolf Electric Cooktops Use & Care Information.
If the cooktop still does not work, contact a Wolf authorized service center. Do not attempt to repair the cooktop yourself. Wolf is not responsible for service required to correct a faulty installation.
IF YOU NEED SERVICE
If service is necessary, maintain the quality built into your electric cooktop by calling a
olf authorized service center.
W
o obtain the name and number of a
T Wolf authorized service center, check the Locator section of our website,
olfappliance.com or call Wolf Customer
w
Service at
800-332-9513
.
When calling for service, you will need the cooktop model and serial numbers. Both numbers are listed on the rating plate, located on the underside of the cooktop
CONTACT INFORMATION
Wolf Customer Service: 800-332-9513
Website: wolfappliance.com
This cooktop must be repaired only by a Wolf authorized service center. The unit must be disconnected from power prior to service.
The information and images are the copyright
olf Appliance Company
ty of W
oper
pr affiliate of Sub-Zero Freezer Company, Inc. Neither this book nor any information or images contained her or in part without the express written permission of Wolf Appliance Company, LLC, an affiliate of Sub-Zer
olf Appliance Company
©W
ein may be copied or used in whole
eezer Company
o Fr
, Inc.
, LLC all rights r
, LLC, an
eserved.
15
WOLF APPLIANCE COMPANY, LLC P.O. BOX 44848 MADISON, WI 53744 800-332-9513 WOLFAPPLIANCE.COM
807606 1
0/2005
Loading...