Sub Zero 7029829 Installation
Integrated Dual Installation
(Hinge to Handle)
subzero.com 800.222.7820
CONTENTS
1 Heater
1 Grommet, plastic
2 Screw, #8–18 x
5
⁄8"
2 Trim, edge guard
1 Plug, 4-pin
2 Tape, black
1 Bracket, mounting hinge–top
1 Bracket, mounting handle–top
1 Bracket, mounting bottom
1 Bracket, mounting hinge–side
1 Bracket, mounting handle–side
5 Clip, center
5 Screw, #6 x
2 Screw, #10 x
2 Screw,
3
⁄8"
1
⁄2"
1
⁄4" –20 x 1⁄2"
1 Trim, center
2 Screw, #10 x
2 Screw, #8–32 x
3
⁄4" self drilling
1
⁄2"
1 Instructions
4 Install edge guard along the upper edge of the opening
and bottom of the heater panel where wires pass. Edge
guard must be trimmed to t.
5 Place leads from heater into the correct pin position on
connector. Pin position is dependent on the model being
installed. Refer to pin placement illustration and chart
below. Place excess wire into opening or secure to the
side of the unit with tape provided.
MODEL WIRE PLACEMENT
All Refrigerator, Wine (Single Door) 2, 4
All Freezer, Combination and Wine
(Door and Drawers)
EDGE
GUARDS
1, 2
4
3
2
1
HEATER INSTALLATION
1 Insert a plastic grommet in the front square hole along
the top edge of the unit, then tap into position.
2 Remove the paper backing from the tape on the back of
the heater.
3 Place heater panel on the left side of the unit being
installed on the right, insert two screws along the top
edge, then press rmly to secure.
Refer to the illustration below.
Heater placement.
Electrical connection.
Pin placement.
PIN ONE
REFERENCE
7029831 REV-C 03/2016
page 1 of 2
Integrated Dual Installation
(Hinge to Handle)
subzero.com 800.222.7820
6 Remove the existing side mounting brackets from the
center of each unit and replace with new hinge side and
handle side brackets. Refer to the illustrations below.
7 Once the brackets are secure, install tape to the front
edge of the heater to prevent interference when second
unit is installed. Refer to the illustration below.
SIDE
MOUNTING
BRACKETS
Side brackets.
8 Install the top brackets using the existing hinge screw
and the #10 x
9 Once the top brackets are secure, install unit into the
1
⁄2" screws. Refer to the illustration below.
HINGE SIDE
BRACKETS
HANDLE SIDE
BRACKETS
Hinge and handle side brackets.
right side of the opening, then install the left.
10 With both units in the opening, use two
1
⁄4" –20 x 1⁄2"
screws to secure the top brackets together.
11 Use ve #6 x
3
⁄8" self drilling screws to install plastic clips
on the hinge side trim. Refer to the illustration below.
12 Align the center trim with the plastic clips, verify the top
of the trim is aligned with the top of the opening, then
press to install.
13 Slightly loosen the two bottom unit tray screws. For 18"
models, drill out rivet and replace with a #8–32 x
1
⁄2"
screw. Insert the bottom bracket into position. Tighten
5
each screw then install two #10 x
⁄8" self drilling screws
to secure the bracket.
REMOVE RIVET
18" MODEL ONLY
Center trim installation.
Bottom bracket.
Top brackets.
HINGE
SIDE BRACKET
HANDLE
SIDE BRACKET
page 2 of 2
Loading...