Page 1
Contents
Tall and Column Models – Dual Installation
subzero.com 800.222.7820
Qty Description
1 Heater
1 Grommet, plastic
2 Screw, #8–18 x 5/8"
2 Trim, edge guard
1 Plug, 4-pin
2 Tape, black
1 Bracket, top
8 Clip, center
8 Screw, #8 x 1/2"
1 Trim, center
1 Instructions
Heater Installation
1) Insert a plastic grommet in the front square hole along
the top edge of the unit, then tap into position.
2) Remove the paper backing from the tape on the back
of the heater.
3) Place heater panel on the left side of the unit being
installed on the right, insert two screws along the
top edge, then press rmly to secure. See illustration
below.
4) Install edge guard along the upper edge of the
opening and bottom of the heater panel where wires
pass. Edge guard must be trimmed to t.
5) Place leads from heater into the correct pin position
on connector. Pin position is dependent on the model
being installed. Refer to pin placement illustration and
chart below. Place excess wire into opening or secure
to the side of the unit with tape provided.
6) Install tape to the front edge of the heater to prevent
interference when second unit is installed. Refer to the
illustration below.
7) Install unit into the right side of the opening, then
install the left.
Model Wire Placement
All Refrigerator, Wine (Single Door) 2, 4
All Freezer, Combination and
Wine (Door and Drawers)
4
3
2
1
PIN ONE
REFERENCE
Pin placement.
TAPE
Secure heater.
1, 2
Heater placement.
EDGE
GUARDS
Electrical connection.
Page 1 of 3
Page 2
Tall and Column Models – Dual Installation
Bracket Installation
Loosen the two screws on the top handle side of each unit.
Slide the top bracket under the four screw heads, then
tighten screws. Refer to the illustration below.
Center Trim Installation
Secure handle side trim using the four sets of clips and
screws provided. Refer to the illustration below. If using a
power drill, set to lowest torque setting to ensure screws
do not strip out inside clips.
Align center trim with clips, verify the top of the trim is
aligned with the top of the opening, then press into position.
subzero.com 800.222.7820
BRACKET
Bracket installation.
TOP
Clip installation.
Page 2 of 3
Page 3
Contents
Drawer Models – Dual Installation
subzero.com 800.222.7820
Qty Description
1 Heater
2 Trim, edge guard
1 Plug, 4-pin
1 Tape, black
4 Clip, center
4 Screw, #8 x 1/2"
1 Trim, center
1 Wire, ground
2 Bracket, center
1 Instructions
Heater Installation
1) Remove paper backing from tape on the back of the
heater panel.
2) Place heater on the left side of the unit being installed
on the right. Align heater with the top of the unit, then
press rmly to secure. See illustration below.
3) Install edge guard along the upper edge of the
opening and bottom of the heater panel where wires
pass. Edge guard must be trimmed to t.
4) Clip ground wire to the opening and heater panel. See
illustration below.
5) Place leads from heater into the correct pin position
on connector. Pin position is dependent on the model
being installed. Refer to pin placement illustration and
chart below. Place excess wire into opening or secure
to the side of the unit with tape provided.
6) Install tape to the front edge of the heater to prevent
interference when second unit is installed.
7) Install unit into the right side of the opening, then
install the left.
Model Wire Placement
All Refrigerator 2, 4
All Freezer, Combination 1, 2
Center Trim Installation
Remove existing center trim from each unit and install the
two center brackets, provided. Secure side trim using the
two sets of clips and screws provided. Refer to the
illustration below. If using a power drill, set to lowest
torque setting to ensure screws do not strip out inside clips.
Align center trim with clips, verify the top of the trim is
aligned with the top of the opening, then press into position.
HEATER
Heater placement.
7023664 REV-A 10/2012
EDGE
GUARD
GROUND
WIRE
Electrical connection.
Pin placement.
Page 3 of 3
4
3
2
1
PIN ONE
REFERENCE
Clip installation.
7023664
Loading...