Sub Zero 7020600, 7020599, 7020596, 7020597, 7007197 Installation
...
700 Series - Integrated Stainless Steel Panel Installation
3755520 / Rev A / June, 2009
1. Before attaching the stainless steel door panel to the
door, remove six outer screws from each of the three
mounting positions and loosen the center screws (See
figure 1).
2. Remove the two pieces of mounting hardware attached
to the front of the door. Then, attach the two pieces to
the back of the stainless steel panel (one for the handle side and one for the hinge side) (See Figure 2).
3. Place the stainless steel door panel lying face down on
a protected surface, to prevent scratches or damage to
the front of the panel.
4. Install stainless steel door panel by engaging the
tabbed bracket to handle side of the door first. Then,
slide hinge side mounting bracket onto positioning
screws on hinge side of the door. NOTE: The panel
can be adjusted 1/4" (6 mm) up and down and side to
side.
5. Once door panel is in place and adjusted correctly,
attach six #10 x 1/2" screws (removed in step 1) to
hinge side mounting bracket. Then, install magnetic
decorative caps (See Figure 1).
As reveal between cabinets and unit decreases, the
potential exists for severe finger pinching if fingers are
placed in the opening when the door is closing.
32-7/8"(835 mm) For 36" Units
23-7/8"(606 mm) For 27" Units
RH Door Swing
Back of Panel
LH Door Swing
Back of Panel
* DIMENSIONS MAY VARY
5-5/16"
(135 mm)
*45-1/4" Min.
(1149 mm)
5-3/16"
(132 mm)
22-7/16"
(570 mm)
*1-7/16" (37 mm)
Figure 2
Page 1 of 2
PROCEDURE:
STAINLESS STEEL DOOR PANEL INSTALLATION
NOTE: It is recommended that the stainless steel door panel of the tall unit be installed first and then the upper
and lower drawer panels.
Magnetic
Decorative Caps
Remove outer
screws first
Loosen
center screws
Remove outer
screw first
SS PANEL
Mounting
Bracket
Figure 1
700 Series - Integrated Stainless Steel Panel Installation
3755520 / Rev A / June, 2009
STAINLESS STEEL DRAWER PANEL INSTALLATIONS
1. Remove the two pieces of mounting hardware attached
to the front of drawer. Then, attach the two pieces to
the back of the stainless steel panel (one for the handle side and one for the hinge side) (See Figure 3).
2. Place the stainless steel drawer panels lying face down
on a protected surface, to prevent damage to the front
of the panels.
3. To help with placement of the drawer panels, examine
the lower “L” bracket and panel to determine the slotted holes on the bracket that will be used. Then, position screws into lower portion of drawer that corresponds with these slots. Leave these screws out just
enough so that the slotted holes in the bracket will
slide under the heads (See Figure 4).
4. With the two mounting brackets in place, install drawer
panel by engaging the top tabbed bracket first, then
slide lower ’L’ bracket onto positioning screws.
NOTE: The panels can be adjusted 1/4" (6 mm) up
and down and side to side.
5. Fasten all screws to lower “L” bracket to secure drawer
panel (See Figure 4).
NOTE: Once drawer panels have been adjusted for
proper spacing, be sure to reconnect the control cable
on the base unit only af
ter you have installed the draw-
er (See Figure 5).
Figure 4
Figure 5
11- 5/1 6"
(287 mm)
8-7/16"
(214 mm)
1-1/4"
(32 mm)
*26-1/2"(673 mm) Min For 27" Units
*35-1/2"(902 mm) Min For 36" Units
1-1/4"
(32 mm)
13-7164" Fixed
(341 mm)
*16-9/16" Max.
(421 mm)
* DIMENSIONS MAY VARY
VIEW FROM BACK OF PANELS
Figure 3
Page 2 of 2
Loading...