Sub-Zero 601RG User Manual

Download

Page 1

Planning Information

Built-In Model 601RG

All Refrigerator with Glass Door

odel 601RG/F

ramed

Model 601RG/O Overlay

Lighted electronic control panel

djustable spill-proof

A glass shelves

gg container

High humidity compartment

Hermetically sealed refrigeration units

Removable kickplate

Serial and model number plate

Front venting allows unit to be completely built in

(Stainless steel design shown )

riple-pane

V resistant low-

U energy glass door

our-sided

F magnetic gaskets

Door closers

Model 601RG/S (P/B) Stainless Steel

The Sub-Zero Model 601RG all refrigerator with glass door is available in your choice of the framed, overlay or stainless steel design application. Three stainless steel finishes are offered— classic (/S), platinum (/P) and carbon (/B).

Dimensions in parentheses are in millimeters unless otherwise specified.

11/06

With the installation of a harness kit, these appliances are Star-K compliant to meet strict religious regulations in conjunction with specific instructions found on star-k.org. You may purchase this harness kit through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero.com.

This handsome addition to Sub-Zero’s inventory of

ou the ability to complement the

models offer commer ously, no door shelves, but there is no loss of storage space in this unit. A roll-out utility drawer is available as an option. Even with the glass door on this unit, you can assure your clients that this model still meets Department of Energy numbers.

s y

cial looking kitchen with ease

. There are, obvi

Page 2

36"

(914)

24"

(610)

73"

(1854)

36"

(914)

361/16"

(916)

351/4"

(895)

237/8"

(606)

BEHIND

FRAME

/8" (10)

FRAME

EXTENSION

Planning Information

Built-In Model 601RG

FEATURES

36" (914) wide all refrigerator with glass

door

Energy Star qualified

Sub-Zero's refrigeration system ensures the

freshest food and energy efficiency

Shallow-depth design means access is easy

to any area of the refrigerator

Electronic digital controls are up front and

easy to use

Bright interior lighting

Adjustable, spill-proof glass shelves

High-humidity crisper drawer is large and deep with removable divider and smooth sides for easy cleaning

Door alarm will let you know with an audible beeping if your refrigerator door is left ajar

Triple-pane UV-resistant low-energy glass door improves insulation

Front venting allows unit to be completely b

uilt in and serviced from the front

UL approved for US and Canada

Two, five and twelve year residential warranty – exclusions apply; warranty information can be found on our website, subzero.com

OVERALL DIMENSIONS

Stainless steel design shown.

ary b

Dimensions ma

Dimensions in parentheses are in millimeters unless otherwise specified.

y v

/8" (3).

Page 3

Planning Information

Built-In Model 601RG

MODEL OPTIONS

Framed Design 601RG/F

Overlay Design 601RG/O

Classic Stainless Steel 601RG/S

Platinum Stainless Steel 601RG/P

Carbon Stainless Steel 601RG/B

ou must allow 90 days from order to

Y delivery for platinum and carbon finishes.

A CCESSORIES

Side panels in white, almond and

classic stainless steel

Extended framed handle

Stainless steel and polished

chrome handles for overlay design

Roll-out deli basket

Dozen egg container with lid

90˚ and 105˚ door stop kits

Accessories are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero.com.

SPECIFICATIONS

odel 601RG All Refrigerator

ith Glass Door

Overall Width 36" (914)

Overall Height 73" (1854)

Overall Depth 24" (610)

Refrigerator Capacity 20.1 cu ft (569 L)

inimum Height (levelers in) 72

/4"

(1848)

Door Swing Clearance 361/16" (916)

Electrical Requirements 115 V AC, 60 Hz, 15 amp circuit

Annual Energ

y Usage 400 kWh / $ 37 (based on 9.06 cents per kilowatt hour) Energy Star Qualified

Shipping Weight Framed – 400 lbs (181 kg)

Overlay – 400 lbs (181 kg)

Stainless Steel – 430 lbs (195 kg)

Special Note Model 601RG has a triple-pane

UV-resistant low-energy glass door

Specifications are subject to change without notice.

Dimensions in parentheses are in millimeters unless otherwise specified.

Page 4

Planning Information

723/4"

(1848)

ROUGH

OPENING

HEIGHT

351/2"

(

902)

OUGH OPENING WIDTH

24"

(610)

ROUGH

OPENING

EPTH

11"

(279)

24"

(610)

LOCATE ELECTRICAL

WITHIN SHADED AREA

(152)

FRONT VIEW

TOP VIEW

Built-In Model 601RG

INSTALLATION SPECIFICATIONS

DIMENSIONS

Finished Rough Opening Width 351/2" (902)

Finished Rough Opening Height 723/4" (1848)

Finished Rough Opening Depth 24" (610)

Location of Electrical Within shaded area

See Installation Instructions shipped with unit for detailed specifications. Refer to the Sub-Zero Design Guide pdf file for additional specifications.

Dimensions in parentheses are in millimeters unless otherwise specified.

Page 5

Planning Information

Built-In Model 601RG

INSTALLATION NOTES

efer to the illustrations and specifications for overall dimensions, finished rough opening dimensions and installation specifics.

llow the door to open a minimum of 90˚ or you'll have problems removing drawers. With the door opening at 90˚, you may have to move drawers slightly to clear the door interior. Refer to the minimum door swing clearance in the specifications chart.

For corner installations, allow for a minimum 3" (76) filler so that the door can open to 90˚. If you're using raised panels, consider using a wider filler. A 90˚ door stop is available as an accessory.

When units are installed side by side, a filler strip is recommended. The width of this filler strip will vary depending on the configuration and panels you use. An anchoring kit may also be used to attach two units together. This kit is available through your Sub-Zero dealer.

Be sure to add the filler strip width to your finished rough opening dimension. In any sideby-side installation without a filler strip, add an additional This will allow for the proper width.

Refer to the full-scale illustrations at the end of this section for specifics on door openings and filler size alternatives.

If your client has chosen the stainless steel design, the unit will be shipped complete with wrapped stainless steel doors and handle hardware. You will not have to install front panels.

If y overlay design, you will be adding front panels to give the unit the custom Sub-Zero look. The overlay design also allows you to add your own handles, or you may choose accessory handles

ailable through your Sub-Zero dealer. Refer to

av pages panels.

/2" (13) to y

our client has chosen the fr

10 for detailed information on adding

–

our combined number

amed or

he refrigerator door panel must include a cut-out to accommodate the window. Refer to the panel specifications for exact dimensions. The glass portion of the door must be exposed a

nd not covered by any part of the panel.

A 115 volt, 60 Hz, 15 amp electrical supply is required. The supply circuit for this appliance must be protected by a 15 amp fuse or circuit breaker. It is recommended that a separate circuit, serving only this appliance, be provided.

All Built-In models are equipped with a 6' (1.8 m) power supply cord with a 3-prong grounding plug which must be plugged into a mating 3-prong grounding type wall receptacle. Locate electrical within the shaded area shown in the installation illustration.

You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service.

To prevent the unit from tipping forward and provide a stable installation, the unit must be secured in place with an anti-tip blocking kit. If there is a solid soffit above the unit with clearance between the unit and the soffit of 1" (25) or less, you won't need to block the unit.

For installations with clearances of more than 1" (25), you must block the unit with the anti-tip bloc

king kit (wood block and hardware)

provided with each Built-In unit.

Refer to the Built-In Installation Instructions packed with the appliance, which provides step-by-step procedures for making sure the unit is installed properly.

Dimensions in parentheses are in millimeters unless otherwise specified.

Page 6

Planning Information

Built-In Model 601RG

ADDING PANELS

In your plan for panels, be sure you are working with the Sub-Zero panel design family called for in your design. If you have chosen the stainless steel design, the unit will be shipped complete with wrapped stainless steel doors and h

andle hardware. You will not have to install front door

panels.

If you and your client have ordered a framed or overlay design model, you will be adding panels to give the unit the custom Sub-Zero look. Specifications on the following pages provide installation considerations for framed and overlay door panels.

Side panels can be used with the framed, overlay and stainless steel design applications. Refer to specifications on page 10.

Dimensions in parentheses are in millimeters unless otherwise specified.

Page 7

Planning Information

PANELS

/4" (6) THICK OR LESS

/4" (6) Panel

Trim reveal

/4" (6) min

PANELS THICKER THAN

/4" (6)

Trim reveal

/4" (6) min

Rout to 1/4" (6)

thickness

B B

133/8" (340)

14" (356) 1

Built-In Model 601RG

FRAMED PANELS

Framed door panel 1/4" (6) thick or less

FRAMED PANELS

If the thickness of the custom panels is less than 1/4" (6), they must be backed up with a sheet of shim material to build the total thickness to

than

/4" (6), an edge must be routed around the panel to

/4" (6). If the panel is thicker

ensure a proper fit. Refer to the illustrations on this page.

MPORTANT NOTE:Routing, recessing or optional

extended handles may be required on raised panels for finger clearance under the handle. Refer to the full-scale illustrations on pages 11– 14.

IMPORTANT NOTE: The weight of each panel cannot exceed 50 lbs (23 kg).

The traditional framed models come with an 11" (279) louvered grille and elegant full-length handle. Optional extended full-length handles that provide additional finger clearance for raised panels are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website

, subzero.com.

Framed door panel thicker than 1/4" (6)

To install framed panels, refer to the installation instructions shipped with each unit

. These instructions can also

be found on our website, subzero.com.

The refrigerator door panel must include a cut-out to accommodate the window. Refer to the chart below for exact dimensions. The glass portion of the door must be exposed and not covered by any part of the panel.

FRAMED PANEL DIMENSIONS

WIDTH HEIGHT

Door P

anel 34

/8" (867) 5815/16"(1497)

Handle Recess Location A – 2915/32" (749)

Window Cut-Out 253/8" (645) 413/16" (1046)

Window Cut-Out Location B – 43/8" (111)

Maximum Panel Weight 50 lbs (23 kg)

Framed Door Panel

Dimensions in parentheses are in millimeters unless otherwise specified.

Page 8

Planning Information

Door/Drawer /

Grille Trim

/16" (2)

/32" (4)

/4" (6) Backer Panel

/16" (8) min

10"

(3)

Spacer Panel

Overlay Panel

Spacer Panel

Overlay Panel

/4" (6)

Backer

Panel

.10"

(3)

~3/4"

(19)

Built-In Model 601RG

OVERLAY PANELS

The overlay design allows decorative panels to cover the door trim for a more seamless appearance that blends with the design of the room. To achieve this look, the most common way is to work with three panels—the decorative overlay panel, a .10" (3) spacer panel and a

/4" (6) backer panel. Depending on your cabinet manufacturer, this could be one panel routed for different dimensions or more likely, three different panels.

Regardless of the physical construction of the panels (routing or three panel assembly), you will need to follow the exact dimensions and panel placement to ensure a proper fit.

The top illustration on this page is a cross section view of the three panel assembly showing placement of the door / drawer / grille trim. The bottom illustration shows a rear view of the three panel assembly and critical dimensions, standard for all overlay models.

Three panel assembly— cross section

Three panel assembl

y— rear view

Overlay models will come with no handle hardware, because the beauty of this design is that you can match the surr

ounding cabinetry hardware. For overlay door panel

dimensions, refer to specifications on page 9.

IMPOR

TANT NOTE:

Keep in mind that the Sub-Zer

o door panels have the potential for hitting adjacent cabinets and/ or countertops when they are opened. You need to be

are of your surrounding cabinetry and space limitations

aw when using the overlay models. Refer to the full-scale illustrations on pages 13 –14.

IMPORTANT NOTE: The weight of each door panel assembly cannot exceed 50 lbs (23 kg). The total thickness of all panels for an overlay model must be at least

/8" (16) thick.

To install overlay panels, refer to the installation instructions shipped with each unit

. These instructions can also

be found on our website, subzero.com.

Do not exceed the dimensions listed for the overlay grille panel. The decorative panel cannot be any larger or it ma

y restrict the air flow to the compressor area

and cause problems with the operation of the unit.

Dimensions in parentheses are in millimeters unless otherwise specified.

Page 9

A A

131/2" (343)

Planning Information

Built-In Model 601RG

OVERLAY PANELS

OVERLAY PANEL DIMENSIONS

WIDTH HEIGHT

Door Panel 347/16" (875) 591/4" (1505)

Door Spacer 331/2" (851) 585/16" (1481)

Door Backer 341/8" (867) 5815/16"(1497)

Window Cut-Out

/16" (646) 4

/4" (1048)

Window Cut-Out Location A – 41/2" (114)

Overlay Door Panel

Maximum Weight (panel assembly) 50 lbs (23 kg)

Dimensions in parentheses are in millimeters unless otherwise specified.

Page 10

Planning Information

(102)

3" (76)

237/8" (

606)

EHIND FRAME

Built-In Model 601RG

SIDE PANELS

Side panels can be used with the framed, overlay and stainless steel design applications. When planning for side panels with the installation of the Built-In model, you need to be aware of space configuration to achieve a pleasing fit. Depending on the exact panel you are using with your unit, the height of the panel will vary.

Cut-outs around the toe kick and grille area are required if

/4" (6) thick panel will be inserted into the main frame channel. The panel will need to be 24" (610) deep. Refer to the illustration on this page for placement of toe kick and grille area cut-outs. If a panel will abut the main frame and should be 23

/8" (10) thick panel is used, the

/8" (606) deep. The toe kick area may or may not be cut out depending on the look you want to achieve.

IMPORTANT NOTE: The use of side panels may change the width of your rough opening.

Cut-outs for grille and toe kick area

HARDWARE CONSIDERATIONS

Overlay models come without handle hardware. The beauty of this design is that you can match the surrounding cabinet hardware. You or the cabinet manufacturer must provide handle hardware to match the overall decorating scheme.

The handle hardware must be installed before installing the panel assembly. Use larger D-style handles. If screws with thick heads are used, the screws will need to be countersunk into the door before the panel is put into

. Refer to the full-scale illustr

place

ations on pages 1

1–12

for handle hardware considerations.

IMPORTANT NOTE: Sub-Zero does not recommend using single pull knobs on any of its Built-In models.

Optional stainless steel handles are available in a variety of diameter

s and lengths in the classic, platinum and carbon stainless steel finishes and polished chrome. Contact your Sub-Zero dealer for specifics. To obtain local dealer information, visit the Locator section of our website,

o.com.

subzer

Dimensions in parentheses are in millimeters unless otherwise specified.

Page 11

Planning Information

11/4"(

32) PANEL

1"(25) PANEL

/4"(6) P

ANEL

/2"(13) PANEL

/4"(19) PANEL

PTIONAL

EXTENDED

FULL-LENGTH

HANDLE

TANDARD

FULL-LENGTH

HANDLE

DOOR

/4"(

FRAMED PANEL

(25)

(

51)

(

76)

Built-In Model 601RG

HANDLE PROFILE – FRAMED APPLICATION

FULL-SCALE TEMPLATES

The following full-scale illustrations enable you to under

stand some of the unique situations you may face as you design the Built-In units into homes. These templates can be easily photocopied or used in y

Dimensions in parentheses are in millimeters unless otherwise specified.

our tr

acings.

HANDLE PROFILE

The full-scale illustration above shows handle placement for the fr

amed a

pplication standard full-length handle and the optional extended full-length handle shown in the dashed line.

Page 12

Planning Information

11/4" (32) PANEL

1" (25) PANEL

/4" (

6) PANEL

/2" (

13) PANEL

/4" (19) PANEL

/8" (16) PANEL

DOOR

/4" (

APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR

NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE

MUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK.

(

51)

(

76)

TANDARD STAINLESS STEEL HANDLE

Built-In Model 601RG

HANDLE PROFILE – STAINLESS STEEL / OVERLAY APPLICATIONS

PANEL AND HANDLE PROFILE

The full-scale illustr placement for the standard stainless steel

ation a

bove shows handle

handle on the wrapped stainless steel door and on overla dashed line

y panel applications shown in the

IMPORTANT NOTE: For overlay applications, the optional stainless steel handle must be mounted on a panel at least

/8" (16) thick.

For overlay applications, mount door handles close to the opening edge of the door for ease of opening

Dimensions in parentheses are in millimeters unless otherwise specified.

Page 13

(32)

PA N

(25)

PA N

(6)

PA N

(13)

PA N

(19)

PA N

130˚ DOOR OPENING

WITH 2" (51) FILLER STRIP

(

TOP VIEW)

OPTIONAL

FRAMED EXTENDED

FULL-LENGTH HANDLE

STANDARD

FRAMED

FULL-LENGTH

HANDLE

OOR CLOSED

DOOR OPEN @ 130˚

HINGE

2" (51)

ILLER STRIP

MAIN FRAME

LLOW FOR FILLER LAP

BEHIND FLANGE

APPROX

PROFILE OF

STAINLESS STEEL DOOR AND HANDLE

OVERLAY PANEL

3/4" (19) THICK

(NOMINAL)

UB-ZERO UNITSUB-ZERO UNIT

Planning Information

Built-In Model 601RG

PANEL AND HANDLE PROFILE – 130˚ DOOR OPENING

The full-scale illustration above shows the panel and handle profile of a 130˚ door opening with 2" (51) filler strip for framed applications.

Interference of door panels with handles at maximum door s optional 90˚ door stop available through your Sub-Zero dealer.

Appr

* stainless steel door

Dimensions in parentheses are in millimeters unless otherwise specified.

oximate thic

wing ma

y require the use of an

kness of wr

pped

To obtain local dealer information, visit the Locator section of our website, subzero.com.

The full-scale illustration on the following page lets you see what considerations you need to

e for any overla

mak how they may interact with adjacent cabinets

y panel applications, and

and/ or countertops.

Page 14

Planning Information

(32)

PA N

(25)

PA N

(6)

PA N

(13)

PA N

(19)

PA N

(32)

(38)

(44)

(0)

(25)

(51)

(57)

(63)

(70)

(76)

(83)

(89)

(6)

(25)

(19)

HINGE

OVERLAY PANEL

3/4" (19) THICK (NOMINAL)

DOOR CLOSED

DOOR OPEN @ 90˚

90˚ DOOR OPENING

(TOP VIEW)

AIN FRAME

NOMINAL OVERALL

WIDTH OF SUB-ZERO

UB-ZERO UNIT

237/8" (606) TO REAR

F SUB-ZERO

Built-In Model 601RG

OVERLAY PANEL APPLICATION – 90˚ DOOR OPENING

kness of wr

oximate thic

Appr

* stainless steel door

Dimensions in parentheses are in

pped

millimeters unless otherwise specified.