Page 1
INSTALLATION GUIDE
600
SERIES
®
Page 2
INSTALLATION GUIDE
600
SERIES
®
Page 3
Before you begin your installation of a Sub-Zero 600 Series
unit, there are a few things you should take special care to
observe. By reading these introductory instructions carefully, you will make the installation procedure easier, problemfree and, most important, safe.
First, as you follow these installation instructions, take particular note of the WARNING! and CAUTION! symbols
when they appear. This information is important for the safe
and efficient installation of this Sub-Zero.
Also, The printed instructions may signal an IMPORTANT
NOTE, which highlights information that is especially
important for a problem-free installation.
3
Second, make sure that the actual equipment that was
shipped to you matches the design you are expecting to
install. Sub-Zero 600 Series models offer the following
design alternatives: Framed, Overlay, Glass Door Models
and Stainless Steel which is available in three finishes:
classic, platinum and carbon stainless steel.
Each of these design options has specific installation
requirements, which means it is vital that the unit match
your planning and space needs. Before you begin,check the
exact model number you need against the model numbers
on the shipping carton.
• Stainless steel units (classic, platinum and carbon finish-
es) are packed in cartons with a gray cap and white lettering identifying them as stainless steel. The stainless steel
unit will have a wrapped door, 1" (25) diameter handles
and heavy-duty stainless steel louvered grille.
• Framed units are packed in cartons with a white cap and
blue lettering identifying them as framed. The framed unit
will have an extruded handle and a louvered grille.
• Overlay units are packed in cartons with a blue cap and
white lettering identifying them as overlay. The unit is
shipped with no handle hardware (hardware is supplied at
the site to match cabinetry at the installation) and a twopart panel grille frame without a panel.
If the unit you receive does not match your requirements,
contact your Sub-Zero dealer.
Please note, this 600 Series installation guide also covers
procedures for the installation of the Model 561.
WARNING
alerts you to a hazard that may cause serious injury or
death if precautions are not followed.
CAUTION
signals a hazard where minor injury or product damage
may occur if you do not follow instructions.
600
SERIES
INSTALLATION GUIDE
Page 4
4
PREPARING THE SPACE
Step 1: First, make sure that the opening where the
Sub-Zero is to be installed is properly prepared. Refer to the
Pre-Installation Specifications illustrations and chart to be
sure the space dimensions, electrical service and plumbing
are correct for the model you are about to install.
Step 2: If you are installing units side by side, a separating
filler strip is recommended. Add the filler strip width to the
finished rough opening dimension. Complete the installation with Anchoring Kit (part #4200900), see page 17.
IMPORTANT NOTE: To operate properly, the door must
open a minimum of 90˚. Use a minimum 3" (76) filler in corner installations to assure a 90˚ door opening.Allow enough
clearance in front of the unit for full door swing.
IMPORTANT NOTE: Make sure the floor under the refrigerator is level with the surrounding finished floor. Protect a
finished floor with plywood, cardboard or some other suitable material before moving the refrigerator across it.
600
SERIES
PRE-INSTALLATION SPECIFICATIONS
MODELS 601R, 601RG AND 601F
723/4"
(1848)
ROUGH
OPENING
HEIGHT
723/4"
(1848)
MINIMUM
HEIGHT
REQUIRED
(LEVELERS IN)
24"
(610)
ROUGH
OPENING
DEPTH
11"
(279)
3"
(76)
24"
(610)
W
LOCATE WATER SUPPLY
WITHIN BOTTOM SHADED
AREA ONLY (601F ONLY)
LOCATE ELECTRICAL
WITHIN ENTIRE SHADED AREA
6"
(152)
E
SHUT-OFF
VALV E
EXTEND WATER LINE
APPROX. 36" (914)
FROM BACK WALL
(601F ONLY)
A
ROUGH OPENING WIDTH
FRONT VIEW
TOP VIEW
Finished Rough Minimum Door
Opening Width (A) Clearance (B)
Model 601R
351/2"(902) 361/16"(916)
Model 601RG
351/2"(902) 361/16"(916)
Model 601F
351/2"(902) 361/16"(916)
NOTE: Dimensions in parentheses are in millimeters.
Dimensions in parentheses are in millimeters unless otherwise specified.
Page 5
5
600
SERIES
PRE-INSTALLATION SPECIFICATIONS
Finished Rough Minimum Door
Opening Width (A) Clearance (B)
Model 611
291/2"(749) 301/8"(765)
Model 611G
291/2"(749) 301/8"(765)
Model 650
351/2"(902) 361/16"(916)
Model 650G
351/2"(902) 361/16"(916)
Model 561
351/2"(902) 203/4"(527)
Model 661
351/2"(902) 203/4"(527)
Model 642
411/2"(1054) 259/16"(649)
Model 680
411/2"(1054) 259/16"(649)
Model 685
411/2"(1054) 259/16"(649)
Model 632
471/2"(1207) 291/4"(743)
Model 690
471/2"(1207) 291/4"(743)
Model 695
471/2"(1207) 291/4"(743)
NOTE: Dimensions in parentheses are in millimeters.
833/4"
(2127)
ROUGH
OPENING
HEIGHT
WITH
STANDARD
11" (279)
GRILLE
827/8"
(2105)
MINIMUM
HEIGHT
REQUIRED
(LEVELERS IN)
751/2"
(1918)
7"
(178)
6"
(152)
A
ROUGH OPENING WIDTH
24"
(610)
ROUGH
OPENING
DEPTH
E
3"
(76)
18"
(457)
W
LOCATE WATER SUPPLY
WITHIN SHADED AREA
LOCATE ELECTRICAL
WITHIN SHADED AREA
6"
(152)
SHUT-OFF
VALV E
EXTEND WATER LINE
APPROX. 36" (914)
FROM BACK WALL
FRONT VIEW
TOP VIEW
B
23
7
/8"
(606)
BEHIND
FRAME
3
/8"(10)
FRAME
EXTENSION
90˚
B
23
7
/8"
(606)
BEHIND
FRAME
3
/8"(10)
FRAME
EXTENSION
90˚
Models 601R, 601RG, 601F,
611, 611G, 650 and 650G
Models 561, 661, 642, 680, 685,
632, 690 and 695
MODELS 611, 611G, 650, 650G, 561,
661, 642, 680, 685, 632, 690 AND 695
MINIMUM DOOR CLEARANCE AT 90˚
Page 6
6
PREPARING ELECTRICAL
CONNECTIONS
Step 3: To prepare the electrical system, rough in the elec-
trical outlet following the Pre-Installation Specifications.
You will need a 115 volt, 60 Hertz electrical supply. Dedicate
a separate 15 amp fuse or circuit breaker to the Sub-Zero
unit, and follow any local codes that apply.
The Sub-Zero unit comes with a power supply cord with a
three-prong grounding plug. The refrigerator must be
plugged into a mating three-prong wall receptacle grounded in accordance with the National Electrical Code and local
codes.
PREPARING PLUMBING
CONNECTIONS
Step 4: For units with automatic ice makers, first rough in
the water supply line. Connect a 1/4" copper line to the
house supply. Use an easily accessible shut-off valve
between the supply and the refrigerator. This is usually
about 6" (152) from the compression fitting. The ice maker
operates on water pressure of 20 psi (1.4 bar) to 100 psi
(6.9 bar).
If the local water supply has high levels of sediment, consider adding an in-line filter. But don’t use a self-piercing
valve. See your Sub-Zero dealer for a saddle valve kit, ask
for part number 4200880.
Good water is important for good ice quality. It is not recommended that the ice maker be connected to a softened
water supply. Water softener chemicals, such as salt from a
malfunctioning softener, can damage the ice maker mold
and lead to poor ice quality. If a softened water supply cannot be avoided, it is important that the water softener be
well maintained and operating properly.
Reverse osmosis systems can be used, provided there is a
consistent water pressure of 20 psi (1.4 bar) to 100 psi (6.9
bar) supplied to the water valve at all times.
Route the water line through the floor within 1/2" (13) from
the wall and no higher than 3" (76) from the floor. If the
water supply is brought in from behind the unit, route the
water line through the wall no more than 3" (76) from the
floor. In either case, allow at least 3' (1 m) of excess copper
tubing outside the wall or floor for easy connection to the
refrigerator.
WARNING
Do not use an extension cord, or two prong adapter.
Electrical ground is required on this appliance.
Do not under any circumstances remove the power supply cord ground prong.
600
SERIES
Dimensions in parentheses are in millimeters unless otherwise specified.
CAUTION
This outlet must be checked by a qualified electrician to
see if it is wired with the correct polarity.Verify that the
outlet provides 115 volts and is correctly grounded. If a
ground fault circuit interrupter (GFCI) circuit is used,
product operation interruptions may occur.
Page 7
7
For Models 601R, 601RG and 601F (stainless steel), the
lower grille snaps out by pulling forward on the bottom of
the grille.
If you’re installing overlay Models 611, 611G, 650, 650G,
561, 661, 642, 685, 632 and 695, first remove the inner
grille panel assembly,as shown in illustration 4. Lift up, then
pull out at the bottom, pull the top section down and out of
the top key slot. Next, remove the five mounting screws
that hold the outer grille panel assembly to the top compartment. See illustration 5.
UNPACKING THE SUB-ZERO
Step 5: Uncrate the unit, remove its wood base and discard
the shipping bolts that hold the wood base to the bottom
of the refrigerator. Remove all packing materials and tape
as well. Do not discard the kickplate. Also, do not discard
the anti-tip kit and hardware, because you may need them
to block your installation. Next, retract the front leveler legs
to let you move the unit more easily during installation.
To reduce the possibility of the unit tipping forward, position the front levelers flat on the floor. Extend these legs
when the unit is finally positioned.
REMOVING THE GRILLE
Step 6: Remove the grille in order to get to the power cord
and move the unit through doorways. For framed and stainless steel Models 611, 611G,650, 650G, 561, 661,642, 680,
685, 632, 690 and 695, remove three counter-sunk grille
screws at the bottom of the grille and cut the red nylon
shipping strap. NOTE: Grille screws are accessed with
door(s) open. Then tilt the grille forward and release the
springs from behind the grille. See illustration 2.
For Models 601R, 601RG and 601F (framed and overlay),
remove the two black screws in the lowest louver in the
grille.Tilt the bottom of the grille out and away. It’ll release
from the top of the grille. See illustration 3.
Grille Springs
Grille
Screws
(inside door)
Illus. 2 Illus. 3
600
SERIES
WARNING
Keep door(s) and drawer(s) taped closed while moving
unit.
Illus. 4 Illus. 5
INNER
GRILLE PANEL
ASSEMBLY
Page 8
8
1"(25)
SOFFIT
3"
(76)
WOOD BLOCK
SHROUD
WALL STUD
SCREW
BLOCKING FOR SAFETY
Step 7: If there is a solid soffit above the unit with clear-
ance between the unit and the soffit of 1" (25) or less, you
won't need to block the unit. See illustration 6. But for
installations with clearances of more than 1" (25), you must
block the unit.
Use the anti-tip kit (wood block and hardware) provided
with the shipping crate. Locate and mark two wall studs
against the wall where the refrigerator will be located.
Next, locate the proper height to clear the unit. The space
between the unit top and the bottom of the wood block
must not be more than 1/4" (6).
Position the wood block over the unit and use the screws
and "L" brackets to lock it in place. Make sure the screws
extend a minimum of 7/8" (22) into each of the two wall
studs. Make sure the wood block extends at least 3" (76)
over the unit and is securely in place. Refer to illustration 7.
Using the front and rear levelers, raise the unit until it
makes contact with the wood block.
Make sure that the front levelers are firmly on the floor, to
reduce the possibility of the cabinet tipping forward.
IMPORTANT NOTE: If at all possible, keep door(s) closed
on the unit until it is properly anchored.
WARNING
To prevent the unit from tipping forward and provide a
stable installation, the unit must be secured in place
with an anti-tip device.
600
SERIES
Illus. 6
Illus. 7
Dimensions in parentheses are in millimeters unless otherwise specified.
Page 9
9
Step 9: Now, level the unit.To adjust the height, turn the
front leveling legs counterclockwise to lower it. Adjust the
rear levelers from the front of the base. Turn the 5/16" hex
bolt clockwise to raise the cabinet, counterclockwise to
lower the cabinet. Refer to illustration 10. When the unit is
leveled properly, or squared off, door adjustments are less
likely to be necessary.
IMPORTANT NOTE: Be sure to reference leveling of the
unit to the floor and not to surrounding cabinetry, by using
the unit main frame and door trim as leveling reference
points. This could effect the operation of the unit, such as
door(s) not closing properly.
Step 10: After the unit has been leveled, install the kick-
plate as shown in illustration 11. Be sure the drain pan is
installed properly.
COMPLETING THE INSTALLATION
Step 8: To complete the installation, first shut off power
to the wall outlet. Plug into a 15 amp grounded outlet
and roll the unit into position under the wood block or soffit. Now you have to connect the ice maker water line.
Remove the 1/4" compression fitting from its plastic bag
and join the water supply line to the solenoid valve.
If desired, the water valve can be removed from mounting
bracket to gain easier access to water connection, as shown
in illustration 8. Purge the line before making the final connection. Illustration 9 applies only to Model 680 and 690.
IMPORTANT NOTE: Turn on the water supply and
check all fittings for leaks. Make certain the electrical
harness is attached to the solenoid.
In areas with water of high mineral content, the use of an
in-line water filter is recommended. Make sure the filter is
positioned and accessible for replacement when necessary.
IMPORTANT NOTE: Let your customer know that the
ice maker will not fill with water immediately, and
that the first three batches of ice produced should be
discarded. Allow 24 hours for proper ice production.
ELECTRICAL
CONNECTION
SOLENOID
VALV E
1
/4" COPPER
SLEEVE
1
/4" COMPRESSION NUT
FRONT
LEVELERS
REAR
ADJUSTMENT
CAUTION
Protect any finished flooring before moving the unit in
place. All full-size Sub-Zero models are equipped with
rollers, so you can easily move the unit into place. If for
any reason the unit has been laid on its back or side,
you must allow the unit to stand upright for a minimum
of 24 hours before connecting power.
WARNING
To reduce the possibility of the cabinet tipping forward,
the front levelers must be in contact with the floor.
CAUTION
The kickplate must be removed for servicing. The floor
cannot interfere with removal. Refer to label mounted
on kickplate support for height clearance.
Step 11: Replace the grille by reversing the procedure in
Step 6 and turn the power back on. If you’re using a panel
grille, refer to Installing Overlay Grille Panels, page 13.
600
SERIES
Illus. 8 Illus. 9
Illus. 10 Illus. 11
Page 10
10
Step 14: With a Phillips screwdriver, remove the handles
from the freezer and refrigerator doors. Slide the panel into
the frame on the door. With the panel in position, replace
the handles. Be sure the panel is inserted completely into
the channel for proper fit and alignment. See illustration 13.
Next, replace the trim moldings by inserting the top, then
the bottom into the handle channel. Release the middle and
set the magnets.
INSTALLING PANELS
Before you begin installing panels, refer to the Panel
Specifications charts, and be sure you are working with the
Sub-Zero panel design called for in your installation plans.
If your customer has chosen the stainless steel design, the
unit has been shipped complete with a finished stainless
steel look. No panels or handle hardware are necessary to
install. In your final preparation for stainless steel units use
a stainless steel cleaner to remove any marks. Abrasive
cleaners should NOT be used, as they may scratch the surface.
If your customer has ordered either framed or overlay units,
you will be installing panels to give the unit the custom
Sub-Zero look.
FRAMED PANELS
Step 12: If your customer has chosen a framed design
application, first remove the door handles to install the
front panels. The handle screws are hidden by a magnet
backed trim molding. Remove the molding using a piece of
tape to pull it away from the handle and expose the handle
screws.The molding will bend at the center so that you can
remove it. See illustration 12.
Step 13: If the thickness of the custom panels is less than
a 1/4" (6), back them up with a sheet of shim material to
build the total thickness to a 1/4" (6). If the panel is thicker than a 1/4" (6), rout an edge around the panel to get a
proper fit. Keep in mind that the weight of each panel cannot exceed 50 lbs (23 kg). Refer to the Framed Panel
Specifications chart on page 12 for panel dimensions.
Additional panel design information can be found in the
Sub-Zero Design Guide.
IMPORTANT NOTE: On all models except Model 680 and
690, routing, recessing or optional extended handles may
be required on raised panels for finger clearance under the
handle. See Accommodations for Raised Panels, page 11.
600
SERIES
Illus. 12 Illus. 13
Dimensions in parentheses are in millimeters unless otherwise specified.
Page 11
INSTALLING FRAMED PANELS
MODEL 680 AND 690
If you're installing a Model 680 or 690 refrigerator/freezer,
first remove the door handle and trim. The screws are hidden by a magnet-backed trim molding. Remove the molding
using a piece of tape to pull it away from the handle and
expose the handle screws.The trim molding will bend out at
the center to allow you to remove it.
With a Phillips screwdriver, remove the door handles on
freezer and refrigerator doors. The door handles also act as
a door trim.
Remove the handle trim panels by sliding them out of the
doors. Different colored handle trim panels and glasswells
are available through your Sub-Zero dealer.
Next, remove the water and ice glasswell by removing the
mounting screw.Then slide the glasswell up and pull it out.
Remove the top and bottom trim fillers held on by the
mounting screws, and the screws holding the vertical trim
strip. Install the door panels by sliding them into the frame
on the door. Refer to illustrations 14 and 15. With the door
panels in place, reverse the steps to reassemble.
11
600
SERIES
Illus. 14 Illus. 15
PARTIAL FRAMED ACCESSORY KIT
MODEL 685 AND 695
If you choose not to use custom wood panels above or
below the glasswell for Model 685 or 695 framed application, a stainless steel insert panel will be provided with the
partial framed accessory kit. This accessory kit (part
#FRAMPAR / #0000034), available through your Sub-Zero
dealer, includes molding and a stainless steel insert panel
for above and below the glasswell on a framed unit.
Detailed installation instructions are included with the partial framed accessory kit.
FRAMED RETROFIT ACCESSORY KIT
MODEL 685 AND 695
With the framed retrofit accessory kit, existing Model 680
or 690 door panels can be used on a new Model 685 or
695 framed unit. This accessory kit (part #FRAMRET /
#0000035), available through your Sub-Zero dealer,
includes moldings and stainless steel insert panels to
accommodate existing Model 680 or 690 framed door
panels.
Detailed installation instructions are included with the
framed retrofit accessory kit.
A CCOMMODATIONS FOR RAISED
P ANELS
You may have to rout, recess or use optional extended handles with some door panel designs to allow for finger clearance. This is particularly true if your unit has raised panels
greater than 1/4" (6) total thickness. Remember, there is a
maximum weight limit of 50 lbs (23 kg) per door panel as
well.
Check the location of offset when you’re using specific routing for the grip area only. Refer to the 600 Series section of
the Sub-Zero Design Guide for a full-scale template of the
standard full length handle and panel. Use this grid template to lay out your panel design for finger clearance when
standard full length handles are used.
Page 12
12
600
SERIES
WW WW
H
14" (356)
WW
H
A
WW
H
G
F
E
H
C
C C
H
W
H
A
B
D
14"
(356)
H
W
H
A
B
14"(356)
C
W
H
A
C C
D
14"(356)
W
H
A
14"(356)
J
I
Models 601R and 601F
Models 611 and 650 Models 561, 661, 642
and 632
Models 685 and 695
Model 601RG
Models 611G and 650G
Framed Refrigerator Panel Framed Freezer Panel
Raised Panel Handle Recess
Model (W) (H) (W) (H) (A) (B)
601R / 601RG
341/8"(867) 5815/16"(1497) 2915/32"(749)
601F
341/8"(867) 5815/16"(1497) 2915/32"(749)
611 / 611G
281/8"(714) 481/16"(1221) 281/8"(714) 183/8"(467) 241/32"(610) 141/16"(357)
650 / 650G
341/8"(867) 481/16"(1221) 341/8"(867) 183/8"(467) 241/32"(610) 171/16"(433)
561 / 661
191/8"(486) 6711/16"(1719) 145/8"(371) 6711/16"(1719) 385/32"(969)
642
24"(610) 6711/16"(1719) 155/8"(397) 6711/16"(1719) 385/32"(969)
680
167/8"(429) 6711/16"(1719) 1213/16"(325) 6711/16"(1719)
685
24"(610) 6711/16"(1719) 155/8"(397) 6711/16"(1719)
685
(Partial Framed) 15
5
/8"(397) 6711/16"(1719) 155/8"(397) 6711/16"(1719)
632
2711/16"(703) 6711/16"(1719) 1715/16"(456) 6711/16"(1719) 385/32"(969)
690
209/16"(522) 6711/16"(1719) 151/8"(384) 6711/16"(1719)
695
2711/16"(703) 6711/16"(1719) 1715/16"(456) 6711/16"(1719)
695
(Partial Framed) 17
15
/16"(456) 6711/16"(1719) 1715/16"(456) 6711/16"(1719)
FRAMED PANEL SPECIFICATIONS
Window Cut-out Location (C) (D)
601RG
43/8"(111) 133/8"(340)
611G / 650G
43/8"(111) 43/8"(111)
Trim Panel Dimension
680 / 690
(Panel E) 6
7
/8"(175) W x 257/32"(641) H
680 / 690
(Panel F) 6
7
/8"(175) W x 317/32"(793) H
680 / 690
(Panel G) 2
9
/16"(65) W x 6711/16"(1719) H
NOTE: Trim panels are .05" (1) thick.
Glasswell Cut-out Location (I) (J)
685 / 695
19/16"(39) 289/16"(726)
Glasswell Cut-out Dimensions
685 / 695
57/8"(150) W x 127/16"(315) H
NOTE: Dimensions in parentheses are in millimeters.
NOTE: Panel specifications are for 600 Series framed (F) models.
Models 680 and 690 Models 685 and 695
Partial Framed
NOTE: For Models 685 and 695, panel thickness in the glasswell
area can range from 1/4" (6) to a maximum of 1-1/8" (29). If the
panel is thicker, you must rout out a minimum 1/4" (6) flat landing
area to accommodate the bezel surrounding the glasswell.
Window Cut-out Dimensions
601RG
253/8"(645) W x 413/16"(1046) H
611G
193/8"(492) W x 395/16"(999) H
650G
253/8"(645) W x 395/16"(999) H
Page 13
If you use screws with thick heads, you will need to countersink the screws into the backer panel before sliding the
assembly into place.
Step 16: Slide the panel into the frame on the door. With
the panel in position, replace the frame end. Be sure the
panel is inserted completely into the channel for proper fit
and alignment. Next, replace the trim molding by inserting
the top, then the bottom into the frame channel. Release
the middle and set the magnets.
GLASSWELL – MODELS 685 AND 695
The dispenser area of Models 685 and 695 has been engineered to enable the use of the overlay panel application.
Installing overlay panels for these models is the same procedure as other 600 Series units.The refrigerator door panel
will need to accommodate a cutout for the glasswell bezel.
To remove the glasswell bezel for Models 685 and 695
overlay application, the water grille and touch pad must be
removed. Lift the water grille up and out. Next remove the
touch pad assembly which is taped in place, by removing
the center plastic mandrel supports. Carefully tilt the touch
pad out and disconnect the wire harness (blue side up) from
the back side of the touch pad. Remove the bezel by removing the (4) four screws. Insert overlay panel into door trim.
Reverse procedure to install bezel, touch pad and water
grille. To install the plastic rivets, insert rivets though the
touch pad and into the control housing and secure by pressing mandrels into the body of the rivets. Refer to illustrations 18 and 19.
IMPORTANT NOTE: Total panel thickness (including backer
and spacer, if used) in the glasswell bezel area can range
from 1/4" (6) to a maximum of 1-1/8" (29). If the panel is
thicker, provisions must be made to router out a space to
accommodate the bezel surrounding the glasswell.
13
INSTALLING OVERLAY PANELS
If your customer has chosen overlay decorative door panels
and grille panel, the unit will be shipped without handle
hardware. The cabinet manufacturer or designer will provide handle hardware at the job site to match the overall
decorating scheme. To install overlay panels, first remove
the magnet backed trim molding using a piece of tape to
pull it away from the frame and expose the screws. The
molding will bend at the center so that you can remove it.
Remove the frame by removing the four screws. The door
channel is now ready to accept the overlay paneling.
Sub-Zero allows a 1/4" (6) space to slide the backing material into place in the frame. If your material is thicker than a
1/4" (6), either rout an edge around the panel to get a proper fit or mount the decorative overlay panel on a sheet of
1/4" (6) thick material and insert the backing material into
the channel.
You must allow for 0.10" (3) space between the backer
board and the decorative panel, so the panel will slide easily into the door frame. Keep in mind that the weight of
each panel assembly cannot exceed 50 lbs (23 kg).
Illustration 16 is a cross section view of the three panel
assembly showing placement of the door/drawer /grille
trim. Illustration 17 shows a rear view of the three panel
assembly and critical dimensions, standard for all models.
IMPORTANT NOTE: The size of the overlay panel is critical. It must fit over the door frame.
Refer to the Overlay Panel Specifications chart on page 14
for exact sizing of all three panels. Additional panel design
information can be found in the Sub-Zero Design Guide.
Step 15: Install the handle hardware before inserting the
panel. We recommend larger D-style pulls.The use of small,
one-piece knobs is not recommended.
600
SERIES
Door/Drawer/
Grille Trim
1
/16" (2)
5
/32" (4)
1
/4" (6) Backer Panel
5
/16" (8) min
.10"
(3)
Spacer Panel
Overlay Panel
Spacer Panel
Overlay Panel
1
/4" (6)
Backer
Panel
.10"
(3)
~3/4"
(19)
Illus. 16 Illus. 17 Illus. 19
Water
Grille
Water
Dispensing
Button
Light
Button
Ice
Dispensing
Button
Touch Pad
Lock
Indicator
Glasswell
Bezel
Illus. 18
Page 14
14
600
SERIES
WW
H
C
C C
H
W
H
D
H
W
H
C
W
H
C C
D
W
H
WW
H
E
F
Models 601R and 601F Models 611 and 650 Models 561, 661, 642
and 632
Model 601RG
O VERLAY PANEL SPECIFICATIONS
Refrigerator Panels Refrigerator Overlay Panel Refrigerator Spacer Panel Refrigerator Backer Panel
Model (W) (H) (W) (H) (W) (H)
601R / 601RG
347/16"(875) 591/4"(1505) 331/2"(851) 585/16"(1481) 341/8"(867) 5815/16"(1497)
611 / 611G
287/16"(722) 487/8"(1241) 271/2"(699) 477/16"(1205) 281/8"(714) 481/16"(1221)
650 / 650G
347/16"(875) 487/8"(1241) 331/2"(851) 477/16"(1205) 341/8"(867) 481/16"(1221)
561 / 661
197/16"(494) 68"(1727) 181/2"(470) 671/16"(1703) 191/8"(486) 6711/16"(1719)
642 / 685
245/16"(618) 68"(1727) 233/8"(594) 671/16"(1703) 24"(610) 6711/16"(1719)
632 / 695
28"(711) 68"(1727) 271/16"(687) 671/16"(1703) 2711/16"(703) 6711/16"(1719)
Freezer Panels Freezer Overlay Panel Freezer Spacer Panel Freezer Backer Panel
Model (W) (H) (W) (H) (W) (H)
601F
347/16"(875) 591/4"(1505) 331/2"(851) 585/16"(1481) 341/8"(867) 5815/16"(1497)
611 / 611G
287/16"(722) 1811/16"(475) 271/2"(699) 173/4"(451) 281/8"(714) 183/8"(467)
650 / 650G
347/16"(875) 1811/16"(475) 331/2"(851) 173/4"(451) 341/8"(867) 183/8"(467)
561 / 661
1415/16"(379) 68"(1727) 14"(356) 671/16"(1703) 145/8"(371) 6711/16"(1719)
642 / 685
1515/16"(405) 68"(1727) 15"(381) 671/16"(1703) 155/8"(397) 6711/16"(1719)
632 / 695
181/4"(464) 68"(1727) 175/16"(440) 671/16"(1703) 1715/16"(456) 6711/16"(1719)
NOTE:
Refer to illustration 20 on the following page for additional overlay panel dimensions.
Models 611G and 650G
Window Cutout Location (C) (D)
601RG
41/2"(114) 131/2"(343)
611G / 650G
41/2"(114) 41/2"(114)
Window Cutout Dimensions
Model 601RG
257/16"(646) W x 411/4"(1048) H
Model 611G
197/16"(494) W x 393/8"(1000) H
Model 650G
257/16"(646) W x 393/8"(1000) H
NOTE: Overlay panel design is not available for Model 680 or 690.
NOTE: Dimensions in parentheses are in millimeters.
NOTE: Panel specifications are for 600 Series overlay (O) models.
Glasswell Cut-out Location (E) (F)
685 / 695
(Door Panel) 1
11
/16"(43) 283/4"(730)
685 / 695
(Spacer Panel) 1
1
/4"(31) 281/4"(718)
685 / 695
(Backer Panel) 1
9
/16"(39) 289/16"(726)
Glasswell Cut-out Dimensions
685 / 695
57/8"(150) W x 127/16"(315) H
Models 685 and 695
NOTE: For Models 685 and 695, panel thickness in the glasswell
area can range from 1/4" (6) to a maximum of 1-1/8" (29). If the
panel is thicker, you must rout out a minimum 1/4" (6) flat landing
area to accommodate the bezel surrounding the glasswell.
Page 15
15
OPTIONAL GRILLE PANEL –
FRAMED APPLICATION
O VERLAY GRILLE PANEL
SPECIFICATIONS
Overlay Spacer Backer
Model Panel (W) Panel (W) Panel (W)
611 / 611G
287/16"(722) 271/2"(699) 283/16"(716)
650 / 650G
347/16"(875) 331/2"(851) 343/16"(868)
561 / 661
347/16"(875) 331/2"(851) 343/16"(868)
642
407/16"(1027) 391/2"(1003) 403/16"(1021)
680 / 685
407/16"(1027) 391/2"(1003) 403/16"(1021)
632
467/16"(1180) 451/2"(1156) 463/16"(1173)
690 / 695
467/16"(1180) 451/2"(1156) 463/16"(1173)
Overlay Spacer Backer
Grille Height Panel (H) Panel (H) Panel (H)
10" Grille
91/4"(235) 85/16"(211) 815/16"(227)
11" Grille*
101/4"(260) 95/16"(237) 915/16"(252)
12" Grille
111/4"(286) 105/16"(262) 1015/16"(278)
13" Grille
121/4"(311) 115/16"(287) 1115/16"(303)
14" Grille
131/4"(337) 125/16"(313) 1215/16"(329)
15" Grille
141/4"(362) 135/16"(338) 1315/16"(354)
*The 11" (279) high grille is standard on overlay models.
NOTE: Dimensions in parentheses are in millimeters.
Model Grille Panel Width (W)
611 / 611G
283/16"(716)
650 / 650G
343/16"(868)
561 / 661
343/16"(868)
642 / 680 / 685
403/16"(1021)
632 / 690 / 695
463/16"(1173)
Grille Height Grille Panel Height (H)
10" Grille
815/16"(227)
11" Grille
915/16"(252)
12" Grille
1015/16"(278)
13" Grille
1115/16"(303)
14" Grille
1215/16"(329)
15" Grille
1315/16"(354)
The 11" (279) high louvered grille is standard on framed models.
NOTE: Dimensions in parentheses are in millimeters.
W
Overlay Grille Panel
H
Overlay Grille Panel Specifications
600
SERIES
INSTALLING OVERLAY GRILLE PANELS
Remove the inner grille panel assembly, see Step 6 on page
7. Remove the top two corner screws and pull away the top
frame. Slide the panel into position in the grille frame. If you
are using a grille panel 1/4" (6) or thinner, you will need to
install a filler.
Reattach the top frame by reinstalling the two top corner
screws. Install the inner grille panel assembly onto the unit,
as described in Step 6.
Refer to the Overlay Grille Panel Specifications chart and
illustration 20 for exact sizing of all three panels.Additional
panel design information can be found in the Sub-Zero
Design Guide.
Spacer Panel
Overlay Panel
1
/4" (6)
Backer
Panel
.10"
(3)
~3/4"
(19)
Illus. 20
CAUTION
Do not exceed the panel dimensions listed for the
appropriate overlay grille panel you are specifying. The
overlay decorative panel cannot be any larger or it may
restrict the air flow to the compressor area and cause
problems with the operation of the Sub-Zero unit.
Page 16
INSTALLING SIDE PANELS
If you’re installing a unit with side panels, check with your
installer or use one of the side panel installation options
shown in illustration 22.
Drill three holes equidistant in a vertical section of the aluminum frame, and install pan head screws. Do not drill
through model and serial number plate. Anchor the side
panel with decorative screws or finishing nails from a local
hardware store. Do not use adhesives. See illustration 21.
The dimensions given in illustration 22 are for typical wood
side panels. If a 1/4" (6) or less panel is used and inserted
into the return channel extrusion, then a 24-1/4" (616) size
is necessary for width. The sheet must also be notched for
grille and other brackets or screws that are in the return
channel. This is only necessary on this application.
IMPORTANT NOTE: The use of side panels may change
the width of your rough opening.
The overall height on the side panel will vary with the
height of the grille being used. Make sure you know your
finished height before cutting any panels.
16
600
SERIES
3" (76)
1
/4" (6)
237/8"
(606)
1
/4" (6)
3" (76)
4" (102)
131/4" (337)
DOOR
FRAME
SIDE PANEL
PAN HEAD
SCREW
11/8"
(29)
24" (610)
24" (610)
241/4" (616)
FRAME
1/4" (6) THICK SIDE PANEL FITTED IN TO UNIT FRAME
600 SERIES SIDE PANEL OPTIONS (top view)
1/8" (3) THICK BATTENS
DOOR PAN HEAD SCREW
SIDE OF SUB-ZERO UNIT
1/4" (6) SIDE PANEL MATERIAL
FRAME
3/8" (10) THICK SIDE PANEL FITTED UP TO UNIT FRAME
1/8" (3) THICK BATTENS
DOOR PAN HEAD SCREW
SIDE OF SUB-ZERO UNIT
3/8" (10) SIDE PANEL MATERIAL
24" (610)
FRAME
METAL SIDE PANEL FITTED UP TO UNIT FRAME
DOOR PAN HEAD SCREW
SIDE OF SUB-ZERO UNIT
METAL SIDE PANEL MATERIAL
24" (610)
FRAME
1/2" (13) THICK SIDE PANEL FITTED UP TO UNIT FRAME
1/8" (3) ROUT
DOOR PAN HEAD SCREW
SIDE OF SUB-ZERO UNIT
1/2" (13) SIDE PANEL MATERIAL
NOTE: Dimensions in parentheses are in millimeters.
FRAME
1/4" (6)
THICK BATTENS
DOOR PAN HEAD SCREW
SIDE OF SUB-ZERO UNIT
1/4" (6) SIDE PANEL MATERIAL
1/4" (6) THICK SIDE PANEL FITTED UP TO UNIT FRAME
1/8" (3) THICK BACK-UP
21/2"
(64)
Illus. 21
Illus. 22
Dimensions in parentheses are in millimeters unless otherwise specified.
Page 17
If you are fastening units to cabinetry:
• First, make sure units have been leveled and aligned, and
doors adjusted.
• Drill three 3/16" (5) holes through both outer trims as
shown in illustration 24.
• Drill a 1/8" (3) pilot hole into the cabinetry.
• Install all six Sems.
ANCHORING THE UNIT
Step 17: After installing front and side panels, leveling,
alignment and door adjustment, anchor the unit to the
opening to assure a proper fit. The Sub-Zero Anchoring Kit
(part #4200900) is available from your Sub-Zero dealer. Be
sure to level and square the unit before anchoring it.
If two units are being tied together:
• Drill three 13/64" (5) holes through the middle trim of
both units.
• Using the Loctite on the screws, install the three Chicago
screw posts.
• Recheck the units for level.
• Drill three 3/16" (5) holes through both outer trims. See
illustration 23.
• Using a 1/8" (3) drill bit, drill into the cabinetry for a pilot
hole.
• Install all six Sems to the cabinetry.
CAUTION
Do not drill through the model and serial number plate.
17
171/8"(435)
171/8"(435)
171/8"
(435)
171/8"(435)
171/8"(435)
171/8"(435)
171/8"(435)
171/8"
(435)
600
SERIES
Illus. 23 Illus. 24
Page 18
18
90 DEGREE DOOR STOP
All 600 Series doors open to 130 degrees. For Model 611
and 650, if you would like to stop the door swing at 90
degrees, remove the door stop pin from the plastic package
located behind the grille and insert it into the space provided on the top hinge plate. See illustration 27. For Model
611G and 650G, remove the door stop pin from the plastic
package located behind the grille and insert it into the
space provided on the hinge plate. See illustration 28.
Tighten firmly with a screwdriver. Optional 90˚ or 105˚ door
stop kits for Models 601R, 601RG,601F, 561, 661, 642,680,
685, 632, 690 and 695 are available through your Sub-Zero
dealer.
ADJUSTING THE HINGES
Now check to make sure doors are properly adjusted. If not,
adjust the top or bottom hinge by first removing and discarding the two small shipping screws. See illustration 25.
Adjust the top door hinges left to right and in or out by
loosening the three allen head screws. Adjust the bottom
door hinge with a 1/8" allen wrench. Refer to illustration
26. The door will now be able to move left to right or in and
out.
600
SERIES
Illus. 25 Illus. 26
Illus. 27 Illus. 28
Dimensions in parentheses are in millimeters unless otherwise specified.
Page 19
SERVICE FOR YOUR SUB-ZERO
REFRIGERATION SYSTEM
If you need service, check the model and serial number on
the plate at the top frame of the unit inside the door.
Contact a Sub-Zero Factory Authorized Service Center, a
dealer, or Sub-Zero Freezer Company, Customer Service
Dept., P. O. Box 44130, Madison, WI 53744-4130, call (800)
222-7820, or e-mail us at customerservice@subzero.com.
THINK SAFETY!
If you are storing or disposing of your old refrigerator,
please do it safely.
Child entrapment accidents can be tragic.
19
600
SERIES
INSTALLATION CHECKLIST
The importance of the installation of your Sub-Zero 600
Series unit cannot be overemphasized. The proper installation of your unit is the responsibility of the selling dealer or
installer.
IMPORTANT NOTE: To ensure a safe and proper installation, the following checklist should be completed by the
installer to ensure that no part of the installation has been
overlooked.
Any questions or problems about your installation should
be directed to your Sub-Zero dealer or Sub-Zero Customer
Service at (800) 222-7820.
•
Has the unit been secured in place with the provided
anti-tip blocking kit or is there clearance of 1" (25) or
less between the unit and a solid soffit
?
• Are both front levelers extended down to make contact
with the floor? Is the unit level?
• Is the power cord plugged into a properly grounded 3-
prong outlet, which has been installed in accordance
with all applicable electrical codes?
• Is the water supply connected for units with an auto-
matic ice maker? Have you checked for leaks?
• Is the drain pan in the proper position? Has the kickplate
been installed properly?
• Are panels attached securely and properly aligned?
• Have the door(s) been aligned for proper appearance
and operation?
• Have all accessories been installed?
• Have any installation/service problems been noted on
the product registration card? Has the registration card
been mailed in?
• Have stainless steel door(s) been inspected for any
imperfections? This is to be done by the dealer/installer
with the customer upon completion of the installation.
NOTE: Classic, platinum and carbon stainless steel panels are covered by a limited 60 day parts and labor warranty for cosmetic defects.
Page 20
SUB-ZERO FREEZER COMPANY, INC.
4717 Hammersley Road • Madison, Wisconsin 53711
(800) 222-7820 • (608) 271-2233 • E-mail: customerservice@subzero.com
3758428 600IG 6/04
®
Loading...