Sub-Zero 601F User Manual

Planning Information

Built-In Model 601F

All Freezer

odel 601F/F

M

ramed

F

Model 601F/O
Overlay

Lighted electronic
control panel

Adjustable wire

helves

s

utomatic ice

A

aker

m

ull-out ice

P
container

Roll-out storage
baskets

Hermetically sealed
refrigeration units

Removable kickplate

Serial and model
number plate

Front venting allows unit
to be completely built in

(Stainless steel design shown )

Adjustable door

helves

s

our-sided

F
magnetic gaskets

Door closers

Model 601F/S (P/B)
Stainless Steel

The Sub-Zero Model 601F all freezer
is available in your choice of the framed,
overlay or stainless steel design application.
Three stainless steel finishes are offered—
classic (/S), platinum (/P) and carbon (/B).

Dimensions in parentheses are in
millimeters unless otherwise specified.

11/06

With the installation of a harness kit, these
appliances are Star-K compliant to meet strict
religious regulations in conjunction with specific
instructions found on star-k.org. You may purchase
this harness kit through your Sub-Zero dealer.
To obtain local dealer information, visit the Locator
section of our website, subzero.com.

Combined with the Model 601R or 601RG this

popular all freezer model strik
This combination is formida

es a handsome pose

ble and no one else in the
market can boast the performance these two offer.
The automatic ice maker has a large storage drawer
for easy access to the crescent-shaped ice.

.

1

36"

(914)

24"

(610)

73"

(1854)

36"

(914)

361/16"

(916)

351/4"

(895)

237/8"

(606)

BEHIND

FRAME

3

/8" (10)

FRAME

EXTENSION

Planning Information

Built-In Model 601F

FEATURES

36" (914) wide all freezer

S

ub-Zero's refrigeration system ensures the

best storage and energy efficiency

Shallow-depth design means access is easy
to any area of the freezer

Electronic digital controls are up front and
easy to use

Bright interior lighting

Adjustable wire shelves

Door alarm will let you know with an audible
beeping if your freezer door is left ajar

Automatic ice maker provides an ample
supply of crescent-shaped ice

Front venting allows unit to be completely
built in and serviced from the front

Meets strict Department of Energy require­ments

UL approved for US and Canada

Two, five and twelve year residential
warranty – exclusions apply; warranty
information can be found on our website,
subzero.com

OVERALL DIMENSIONS

Stainless steel design shown.

1

±

y

ary b

Dimensions ma

Dimensions in parentheses are in
millimeters unless otherwise specified.

y v

/8" (3).

2

Planning Information

Built-In Model 601F

SPECIFICATIONS

M

odel 601F All Freezer

Overall Width 36" (914)

Overall Height 73" (1854)

MODEL OPTIONS

Framed Design 601F/F

Overlay Design 601F/O

Classic Stainless Steel 601F/S

Platinum Stainless Steel 601F/P

Carbon Stainless Steel 601F/B

ou must allow 90 days from order to

Y
delivery for platinum and carbon finishes.

A CCESSORIES

Front panels for framed design
in white, almond and classic
stainless steel

Side panels in white, almond and
classic stainless steel

Extended framed handle

Stainless steel and polished
chrome handles for overlay design

90˚ and 105˚ door stop kits

Accessories are av
Sub-Zero dealer. To obtain local dealer
information, visit the Locator section of
our website, subzero.com.

ailable through your

Overall Depth 24" (610)

Freezer Capacity 19.3 cu ft (547 L)

M

inimum Height (levelers in) 72

3

/4"

(1848)

Door Swing Clearance 361/16" (916)

Electrical Requirements 115 V AC, 60 Hz, 15 amp circuit

Plumbing Requirements

ater Supply 20–100 psi

W

1

/4" copper line

Annual Energy Usage 737 kWh / $ 67
(based on 9.06 cents per kilowatt hour)

Shipping Weight Framed – 378 lbs (171 kg)

Overlay – 378 lbs (171 kg)

Stainless Steel – 406 lbs (184 kg)

Specifications are subject to change without notice.

Dimensions in parentheses are in
millimeters unless otherwise specified.

3

Planning Information

723/4"

(

1848)

ROUGH

OPENING

HEIGHT

351/2"

(902)

ROUGH OPENING WIDTH

24"

(

610)

R

OUGH

O

PENING

D

EPTH

11"

(279)

3"

(76)

24"

(610)

W

LOCATE WATER SUPPLY

WITHIN BOTTOM SHADED

AREA ONLY

LOCATE ELECTRICAL

WITHIN ENTIRE SHADED AREA

6"

(152)

E

SHUT-OFF

VALVE

E

XTEND WATER LINE

A

PPROX. 36" (914)

F

ROM BACK WALL

FRONT VIEW

TOP VIEW

Built-In Model 601F

INSTALLATION SPECIFICATIONS

DIMENSIONS

Finished Rough Opening Width 351/2" (902)

Finished Rough Opening Height 723/4" (1848)

Finished Rough Opening Depth 24" (610)

Location of Electrical Within entire shaded area

Location of W

See Installation Instructions shipped with unit for detailed specifications.
Refer to the Sub-Zero Design Guide pdf file for additional specifications.

Dimensions in parentheses are in
millimeters unless otherwise specified.

ater Supply

Within lower shaded area

4

Planning Information

Built-In Model 601F

INSTALLATION NOTES

R

efer to the illustrations and specifications
for overall dimensions, finished rough opening
dimensions and installation specifics.

A

llow the door to open a minimum of 90˚ or
you'll have problems removing drawers. With
the door opening at 90˚, you may have to move
drawers slightly to clear the door interior. Refer
to the minimum door swing clearance in the
specifications chart.

For corner installations, allow for a minimum
3" (76) filler so that the door can open to 90˚.
If you're using raised panels, consider using a
wider filler. A 90˚ door stop is available as an
accessory.

When units are installed side by side, a filler
strip is recommended. The width of this filler
strip will vary depending on the configuration
and panels you use. An anchoring kit may also
be used to attach two units together. This kit is
available through your Sub-Zero dealer.

Be sure to add the filler strip width to your
finished rough opening dimension. In any side­by-side installation without a filler strip, add an
additional
This will allow for the proper width.

Refer to the full-scale illustrations at the end
of this section for specifics on door openings
and filler size alternatives.

If your client has chosen the stainless steel
design, the unit will be shipped complete with
wrapped stainless steel doors and handle
hardware. You will not have to install front
panels.

If y
overlay design, you will be adding front panels
to give the unit the custom Sub-Zero look. The
overlay design also allows you to add your own
handles, or you may choose accessory handles

ailable through your Sub-Zero dealer. Refer to

av
pages
panels.

F
maker, rough in the water supply line. Connect

1

a

/4" OD copper line to the house supply
sure to use an easily accessible shut off valve
between the supply and the unit.

1

/2" (13) to y

our client has chosen the fr

10 for detailed information on adding

–

6

our combined number

amed or

s.

or Built-In models with an automatic ice

, being

D

o not use self-piercing valves. A saddle
valve kit (4200880) is available from your
Sub-Zero dealer. To obtain local dealer informa­tion, visit the Locator section of our website,
s

ubzero.com.

A line filter is required when water condi­tions have a high sediment content. The ice
maker operates on water pressure of 20 psi
(1.4 bar) to 100 psi (6.9 bar). In some cases a
reverse osmosis water filter system may not be
able to maintain the minimum water pressure
consistently.

The water line should be routed up through

1

the floor within

/2" (13) from the back wall and
no higher than 3" (76) off the floor. If you have
to come through the wall, make sure the water
line is no more than 3" (76) fr

om the floor.
Locate water supply within the lower shaded
area shown in the installation
illustration.

Regardless of the routing, allow 3' (.9 m) of
excess copper tubing to remain outside the wall
or floor for easy connection to the unit.

A 115 v

olt, 60 Hz, 15 amp electrical supply
is required. The supply circuit for this appliance
must be pr

otected by a 15 amp fuse or circuit
breaker. It is recommended that a separate
circuit, serving only this appliance, be provided.

All Built-In models are equipped with a 6'
(1.8 m) power supply cord with a 3-prong
grounding plug which must be plugged into a
mating 3-prong grounding type wall receptacle.
Locate electrical within the shaded area shown
in the installation illustration.

ou must follow all National Electrical Code

Y
regulations. In addition, be aware of local codes
and ordinances when installing your service.

To prevent the unit from tipping forward and

ovide a stable installation, the unit must be

pr
secured in place with an anti-tip bloc

king kit. If
there is a solid soffit above the unit with clear­ance between the unit and the soffit of 1" (25)
or less, y

ou won't need to bloc

or installations with clear

F

k the unit.

ances of more
than 1" (25), you must block the unit with the
anti-tip blocking kit (wood block and hardware)
provided with each Built-In unit.

Refer to the Built-In Installation Instructions

ed with the a

k

pac

ppliance

, which pr

ovides
step-by-step procedures for making sure the
unit is installed properly.

Dimensions in parentheses are in
millimeters unless otherwise specified.

5

Planning Information

Built-In Model 601F

ADDING PANELS

In your plan for panels, be sure you are working with the
Sub-Zero panel design family called for in your design. If
you have chosen the stainless steel design, the unit will be
shipped complete with wrapped stainless steel doors and
h

andle hardware. You will not have to install front door

panels.

If you and your client have ordered a framed or overlay
design model, you will be adding panels to give the unit
the custom Sub-Zero look. Specifications on the following
pages provide installation considerations for framed and
overlay door panels.

Side panels can be used with the framed, overlay and
stainless steel design applications. Refer to specifications
on page 10.

Dimensions in parentheses are in
millimeters unless otherwise specified.

6

Planning Information

PANELS

1

/4" (6) THICK OR LESS

1

/4" (6) Panel

Trim reveal

1

/4" (6) min

PANELS THICKER THAN

1

/4" (6)

Trim reveal

1

/4" (6) min

Rout to 1/4" (6)

thickness

W

H

A

14" (356)

Built-In Model 601F

FRAMED PANELS

Framed door panel 1/4" (6) thick or less

FRAMED PANELS

If the thickness of the custom panels is less than 1/4"
(6), they must be backed up with a sheet of shim material
to build the total thickness to

1

than

/4" (6), an edge must be routed around the panel to

1

/4" (6). If the panel is thicker

ensure a proper fit. Refer to the illustrations on this page.

I

MPORTANT NOTE:Routing, recessing or optional

extended handles may be required on raised panels for
finger clearance under the handle. Refer to the full-scale
illustrations on pages 11– 14.

IMPORTANT NOTE: The weight of each panel cannot
exceed 50 lbs (23 kg).

The traditional framed models come with an 11" (279)
louvered grille and elegant full-length handle. Optional
extended full-length handles that provide additional finger
clearance for raised panels are available through your
Sub-Zero dealer. To obtain local dealer information, visit
the Locator section of our website

, subzero.com.

Framed door panel thicker than 1/4" (6)

To install framed panels, refer to the installation instruc­tions shipped with each unit

. These instructions can also

be found on our website, subzero.com.

FRAMED PANEL DIMENSIONS

WIDTH HEIGHT

Door Panel 341/8" (867) 5815/16"(1497)

Handle Recess Location A – 2915/32" (749)

Maximum Panel Weight 50 lbs (23 kg)

Framed Door Panel

Dimensions in parentheses are in
millimeters unless otherwise specified.

7

Planning Information

Door/Drawer /

Grille Trim

1

/16" (2)

5

/32" (4)

1

/4" (6) Backer Panel

5

/16" (8) min

.

10"

(3)

Spacer Panel

Overlay Panel

Spacer Panel

Overlay Panel

1

/4" (6)

Backer

Panel

.10"

(3)

~3/4"

(19)

Built-In Model 601F

OVERLAY PANELS

OVERLAY PANELS

The overlay design allows decorative panels to cover the
door trim for a more seamless appearance that blends
with the design of the room. To achieve this look, the
most common way is to work with three panels—the
decorative overlay panel, a .10" (3) spacer panel and a

1

/4"
(6) backer panel. Depending on your cabinet manufacturer,
this could be one panel routed for different dimensions or
more likely, three different panels.

Regardless of the physical construction of the panels
(routing or three panel assembly), you will need to follow
the exact dimensions and panel placement to ensure a
proper fit.

The top illustration on this page is a cross section view of
the three panel assembly showing placement of the
door / drawer / grille trim. The bottom illustration shows a
rear view of the three panel assembly and critical dimen­sions, standard for all overlay models.

Three panel assembly— cross section

Three panel assembl

y— rear view

Overlay models will come with no handle hardware,
because the beauty of this design is that you can match
the surr

ounding cabinetry hardware. For overlay door panel

dimensions, refer to specifications on page 9.

IMPOR

TANT NOTE:

Keep in mind that the Sub-Zer

o door
panels have the potential for hitting adjacent cabinets
and/ or countertops when they are opened. You need to be

are of your surrounding cabinetry and space limitations

aw
when using the overlay models. Refer to the full-scale
illustrations on pages 13 –14.

IMPORTANT NOTE: The weight of each door panel
assembly cannot exceed 50 lbs (23 kg). The total thick­ness of all panels for an overlay model must be at least

5

/8" (16) thick.

To install overlay panels, refer to the installation instruc­tions shipped with each unit

. These instructions can also

be found on our website, subzero.com.

Dimensions in parentheses are in
millimeters unless otherwise specified.

8

Planning Information

W

H

Built-In Model 601F

Overlay Door Panel

OVERLAY PANELS

OVERLAY PANEL DIMENSIONS

WIDTH HEIGHT

Door Panel 347/16" (875) 591/4" (1505)

Door Spacer 331/2" (851) 585/16" (1481)

5

Door Backer 341/8" (867) 58

1

/16"(1497)

Maximum Weight (panel assembly) 50 lbs (23 kg)

Dimensions in parentheses are in
millimeters unless otherwise specified.

9

Planning Information

4"

(102)

3" (76)

237/8" (

606)

B

EHIND FRAME

Built-In Model 601F

SIDE PANELS

SIDE PANELS

Side panels can be used with the framed, overlay and
stainless steel design applications. When planning for side
panels with the installation of the Built-In model, you need
to be aware of space configuration to achieve a pleasing
fit. Depending on the exact panel you are using with your
unit, the height of the panel will vary.

Cut-outs around the toe kick and grille area are required if

1

a

/4" (6) thick panel will be inserted into the main frame
channel. The panel will need to be 24" (610) deep. Refer to
the illustration on this page for placement of toe kick and
grille area cut-outs. If a
panel will abut the main frame and should be 23

3

/8" (10) thick panel is used, the

7

/8" (606)
deep. The toe kick area may or may not be cut out
depending on the look you want to achieve.

IMPORTANT NOTE: The use of side panels may change
the width of your rough opening.

Cut-outs for grille and toe kick area

HARDWARE CONSIDERATIONS

Overlay models come without handle hardware. The
beauty of this design is that you can match the surround­ing cabinet hardware. You or the cabinet manufacturer
must provide handle hardware to match the overall deco­rating scheme.

The handle hardware must be installed before installing
the panel assembly. Use larger D-style handles. If screws
with thick heads are used, the screws will need to be
countersunk into the door before the panel is put into

. Refer to the full-scale illustr

place

ations on pages 1

1–12

for handle hardware considerations.

IMPORTANT NOTE: Sub-Zero does not recommend using
single pull knobs on any of its Built-In models.

Optional stainless steel handles are available in a variety of
diameter

s and lengths in the classic, platinum and carbon
stainless steel finishes and polished chrome. Contact
your Sub-Zero dealer for specifics. To obtain local dealer
information, visit the Locator section of our website,

o.com.

subzer

Dimensions in parentheses are in
millimeters unless otherwise specified.

10

Planning Information

11/4"(

32) PANEL

1"(25) PANEL

1

/4"(6) P

ANEL

1

/2"(13) PANEL

3

/4"(19) PANEL

O

PTIONAL

EXTENDED

FULL-LENGTH

HANDLE

S

TANDARD

FULL-LENGTH

HANDLE

DOOR

1

/4"(

6)

FRAMED PANEL

1"

(25)

2"

(

51)

3"

(

76)

Built-In Model 601F

HANDLE PROFILE – FRAMED APPLICATION

FULL-SCALE TEMPLATES

The following full-scale illustrations enable you
to under

stand some of the unique situations
you may face as you design the Built-In units
into homes. These templates can be easily
photocopied or used in y

Dimensions in parentheses are in
millimeters unless otherwise specified.

our tr

acings.

HANDLE PROFILE

The full-scale illustration above shows handle
placement for the fr

amed a

pplication standard
full-length handle and the optional extended
full-length handle shown in the dashed line.

11

Planning Information

11/4" (32) PANEL

1" (25) PANEL

1

/4" (

6) PANEL

1

/2" (

13) PANEL

3

/4" (19) PANEL

5

/8" (16) PANEL

DOOR

1

/4" (

6)

APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR

NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE

MUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK.

1"

2"

(

51)

3"

(

76)

S

TANDARD STAINLESS STEEL HANDLE

Built-In Model 601F

HANDLE PROFILE – STAINLESS STEEL / OVERLAY APPLICATIONS

PANEL AND HANDLE PROFILE

The full-scale illustr
placement for the standard stainless steel

ation a

bove shows handle

handle on the wrapped stainless steel door and
on overla
dashed line

y panel applications shown in the

.

IMPORTANT NOTE: For overlay applications,
the optional stainless steel handle must be
mounted on a panel at least

5

/8" (16) thick.

For overlay applications, mount door handles
close to the opening edge of the door for ease
of opening

.

Dimensions in parentheses are in
millimeters unless otherwise specified.

12

1

1

/

4

"

(32)

PA N

EL

1"

(25)

PA N

EL

*

1

/

4

"

(6)

PA N

EL

1

/

2

"

(13)

PA N

EL

3

/

4

"

(19)

PA N

EL

130˚ DOOR OPENING

WITH 2" (51) FILLER STRIP

(

TOP VIEW)

OPTIONAL

FRAMED EXTENDED

FULL-LENGTH HANDLE

STANDARD

FRAMED

FULL-LENGTH

HANDLE

D

OOR CLOSED

DOOR OPEN @ 130˚

HINGE

2" (51)

F

ILLER STRIP

MAIN FRAME

A

LLOW FOR FILLER LAP

BEHIND FLANGE

APPROX

PROFILE OF

STAINLESS
STEEL DOOR
AND HANDLE

OVERLAY PANEL

3/4" (19) THICK

(NOMINAL)

S

UB-ZERO UNITSUB-ZERO UNIT

Planning Information

Built-In Model 601F

PANEL AND HANDLE PROFILE – 130˚ DOOR OPENING

The full-scale illustration above shows the panel
and handle profile of a 130˚ door opening with
2" (51) filler strip for framed applications.

Interference of door panels with handles at
maximum door s
optional 90˚ door stop available through your
Sub-Zero dealer.

Appr

*
stainless steel door

Dimensions in parentheses are in
millimeters unless otherwise specified.

oximate thic

wing ma

y require the use of an

kness of wr

.

pped

a

To obtain local dealer information, visit the
Locator section of our website, subzero.com.

The full-scale illustration on the following page
lets you see what considerations you need to

e for any overla

mak
how they may interact with adjacent cabinets

y panel applications, and

and/ or countertops.

13

Planning Information

1

1

/4

"

(32)

PA N

EL

1"

(25)

PA N

EL

*

1

/4

"

(6)

PA N

EL

1

/2

"

(13)

PA N

EL

3

/4

"

(19)

PA N

EL

1

1

/4

"

(32)

1

1

/2

"

(38)

1

3

/4

"

(44)

0"

(0)

1"

(25)

2"

(51)

2

1

/4

"

(57)

2

1

/

2

"

(63)

2

3

/

4

"

(70)

3"

(76)

3

1

/4

"

(83)

3

1

/

2

"

(89)

1

/4

"

(6)

1

/2

"

(25)

3

/4

"

(19)

HINGE

OVERLAY PANEL

3/4" (19) THICK (NOMINAL)

DOOR CLOSED

DOOR OPEN @ 90˚

90˚ DOOR OPENING

(TOP VIEW)

M

AIN FRAME

NOMINAL OVERALL

WIDTH OF SUB-ZERO

S

UB-ZERO UNIT

237/8" (606) TO REAR

O

F SUB-ZERO

Built-In Model 601F

OVERLAY PANEL APPLICATION – 90˚ DOOR OPENING

kness of wr

.

oximate thic

Appr

*
stainless steel door

Dimensions in parentheses are in

pped

a

millimeters unless otherwise specified.

14