Page 1
Planning Information
Wine Storage Model 424
Undercounter
odel 424/O
M
verlay
O
Model 424/S
Classic
Stainless Steel
iscreet lighting
D
Lighted electronic
ontrol panel
c
oller-assembly
R
shelves
Stationary shelf UV-resistant glass
ront venting with
Home security tie-in
With the installation of a harness kit, these appliances
are Star-K compliant to meet strict religious regulations
in conjunction with specific instructions found on
star-k.org. You may purchase this harness kit through
your Sub-Zero dealer. To obtain local dealer information,
visit the Locator section of our website, subzero.com.
F
removable kickplate
erial and model
S
number plate
Full-view glass
oor
d
ivider gasket
D
The Sub-Zero undercounter Model
424 Wine Storage unit is available in your
choice of the overlay or classic stainless
steel design application. A unit with high
altitude glass may be special ordered for
installations at or above 5,000' (1524 m)
in elevation.
Dimensions in parentheses are in
millimeters unless otherwise specified.
11/06
A great addition to Sub-Zero's complete line of
residential refrigeration is the Wine Storage equipment.
But it is more than just wine storage in the conventional sense. It is wine storage as only Sub-Zero could
make it. The ultimate in beauty, engineering, attention
to detail and smart thinking.
The most popular unit of the Wine Storage equipment,
Model 424, offer
bility as the larger models in this line, but in a
pa
ca
compact manner
your kitchen or bar area where you can ensure your
clients have the opportunity to store and offer their
wines at the proper drinking temperatures.
s your client all of the functioning
. It’s ideal for those small places in
1
Page 2
Planning Information
FRONT VIEW SIDE VIEW
(CABINET DIMENSION)
4
(102)
3
4
(273)
10
CENTERED
DOOR FRAME
(597)
1
2
23
30
(767)
DOOR
FRAME
*34
(864)
(587)
1
8
23
3
16
23
7
8
(606)
*
1
/2" (13)
+
_
ADJUSTMENT IN LEVELING LEGS
90˚
253/8"
(645)
TOP VIEW
Wine Storage Model 424
FEATURES
Undercounter Wine Storage unit with 46
(750 ml) bottle capacity
Overlay and stainless steel design options
Refrigeration system allows individual
temperature control of the two wine
c
ompartments and ideal humidity
Sturdy, rustproof wire shelves accommodate
standard 750 ml bottles, half-bottles, as well
as magnums
Roller-glide shelves faced with natural cherry
wood have a three-quarter extension for
easy access
Full-view glass door with UV-resistant glass
protection
High altitude glass door unit can be special
ordered
Discreet low voltage interior lighting
Service light indicator, optional lock and
tie-in to home security system
UL approved for US and Canada
Two, five and twelve year residential
arranty—exclusions apply; warranty
w
information can be found on our website,
subzero.com
OVERALL DIMENSIONS
Dimensions may vary by ±1/8" (3).
Dimensions in parentheses are in
millimeters unless otherwise specified.
2
Page 3
Planning Information
Wine Storage Model 424
SPECIFICATIONS
M
odel 424 Undercounter Wine Storage Unit
Overall Width 237/8" (606)
Overall Height 34 " (864)
MODEL OPTIONS
Overlay Design 424__/O
Classic Stainless Steel 424__/S
DOOR OPTIONS
Full-View Glass Door 424G/__
High Altitude Glass Door 424HAG/__
You must allow 90 days from order to
delivery for high altitude glass door unit.
ACCESSORIES
Tubular handles in classic,
platinum and carbon stainless
steel
Polished chrome handle for
overlay design
UL approved door lock kit
Accessories are available through your
Sub-Zero dealer. To obtain local dealer
information, visit the Locator section of
our website, subzero.com.
Overall Depth 24" (610)
Wine Storage Capacity 46 Bottles (750 ml)
M
inimum Height Required 34
1
/4"
(870)
Door Swing Clearance 253/8" (645)
Electrical Requirements 115 V AC, 60 Hz, 15 amp circuit
Shipping Weight Overlay – 190 lbs (86 kg)
Stainless Steel – 195 lbs (88 kg)
Special Note High altitude glass door is available
for elevations 5,000' (1524 m) or above
Specifications are subject to change without notice.
Dimensions in parentheses are in
millimeters unless otherwise specified.
3
Page 4
Planning Information
A
NTI-TIP BRACKET
FRONT VIEW
TOP VIEW
341/2"
(
876)
ROUGH
O
PENING
HEIGHT
341/4"
(870)
MINIMUM
HEIGHT
REQUIRED
24"(610)
ROUGH OPENING
WIDTH
151/2"
(394)
24"
(
610)
R
OUGH
OPENING
D
EPTH
LOCATE ELECTRICAL
WITHIN SHADED AREA
E
41/2"
(
114
)
21/2"
(64)
Wine Storage Model 424
INSTALLATION SPECIFICATIONS
DIMENSIONS
Finished Rough Opening Width 24" (610)
inished Rough Opening Height
F
inished Rough Opening Depth
F
Location of Electrical Within shaded area
See Installation Instructions shipped with unit for detailed specifications.
Dimensions in parentheses are in
millimeter
s unless otherwise specified.
1
4
3
/2" (876)
24" (610)
4
Page 5
Planning Information
Wine Storage Model 424
INSTALLATION NOTES
R
efer to the illustrations and specifications
for overall dimensions, finished rough opening
dimensions and installation specifics.
T
he Wine Storage unit must be installed to
open a minimum of 90˚ or you will have
problems pulling the shelves out.
For corner installations, you need allow for a
minimum 3" (76) filler so the door can open to
90˚. If you are using some larger handle
hardware, you will also need to take that into
account.
If you are installing a wine unit next to an
existing Sub-Zero unit, you may have to allow
for a filler strip. Also, if there is 2" (51) or less in
between units, an optional heater kit will need
to be installed to prevent moisture from forming
in between units. The optional heater kit is available from your Sub-Zero dealer. To obtain local
dealer information, visit the Locator section of
our website, subzero.com.
If you are connecting the unit to your home
security system, you must allow a minimum of
36" (914) of the system's wiring to be routed in
the electrical area designated for y
The anti-tip bracket must be installed to
prevent the unit from tipping forward.
When planning to install the Model 424 next
to adjoining cabinetry, you must make provisions to allow the door to open to a maximum
of 145˚ and not interfere with the door panel.
Refer to the full-scale illustration on page 11 for
cabinetry dimensions.
For the overlay design, you will need to
ovide a door panel fr
pr
ame for the glass door
Refer to pages 6–7 for complete panel
information.
our model.
.
I
MPORTANT NOTE:Asolid door panel must
not be installed on a glass door unit, as this
may cause moisture to form behind the panel.
F
or overlay panel applications, you must
supply your own handle hardware. It is recommended you use our optional handles and use
the pre-drilled holes supplied to locate the
handles within the frame of our unit. Refer to
page 8 for specifics about installing handle
hardware.
For Model 424, the weight limit for the door
panel frame is 10 lbs (5 kg).
Sub-Zero has provided a natural cherry wood
facing to each of the wine shelves. You can
choose to replace these strips with wood more
complementary to your design and surrounding
cabinetry. Refer to the full-scale illustration on
page 10 for dimensions on the wood facing.
A 115 V AC, 60 Hz, 15 amp fused electrical
supply is required. It is recommended that a
separate circuit, serving only this appliance, be
provided.
All Sub-Zero Wine Storage units are
equipped with a power supply cord with a
3-prong grounding plug which must be plugged
into a mating 3-prong grounding type wall
receptacle. Locate electrical within the shaded
area shown in the installation illustr
ation on
page 4.
You must follow all National Electrical Code
regulations. In addition, be aware of local codes
and ordinances when installing your service.
Refer to the Wine Storage Installation Instructions
ed with the a
k
pac
ppliance
, which provides
step-by-step procedures for making sure the
unit is installed properly.
Dimensions in parentheses are in
millimeters unless otherwise specified.
5
Page 6
Planning Information
Wine Storage Model 424
A solid panel must not be
installed on a glass door unit, as
this may cause moisture to form
behind the panel.
INTEGRATING CABINETRY
Unless you are installing a stainless steel unit, you will
need to provide a door panel frame for the glass door. If
you order a stainless steel unit, the Model 424 will be
shipped with panels and hardware installed.
OVERLAY PANELS
The overlay panel applied to Model 424 should not be
confused with the Built-In overlay panel application. The
overlay panel will consist of only a frame and would be
either the
5
/8" (16) or 3/4" (19) panel you may be using. It is
affixed directly to the door itself with screws through a
series of pre-drilled holes in the perimeter of the door
itself. You do not need any backer or spacer panel.
The glass door opening of the Model 424 is designed to
be exposed to room air circulation. Decorative overlays on
the glass should be k
ept to a minimum. Also, r
ails and
stiles can be increased in size but should not exceed
cabinet manufacturers standard width. They cannot
exceed over
all door panel dimensions specified, as they
would interfere with the operation of the door. The back
sides of rails and stiles that will be visible through the
glass door will need to be finished
. Also, the inside edges
of the frame must be finished to match the front surface.
Dimensions in parentheses are in
millimeters unless otherwise specified.
6
Page 7
Planning Information
* INCH (13) ADJUSTMENT IN LEVELING LEGS
**
MODEL 424/S (STAINLESS STEEL WRAPPED DOOR) FINISHES OFF AT 23 INCHES DEEP
MODEL 424 CABINETRY DIMENSIONS
1
2
FRONT VIEW SIDE VIEW
(CABINET DIMENSION)
DOOR PANEL
(
603)
3
4
23
30
(764)
DOOR
PANEL
CENTERED
VERTICALLY
*34
1
2
(877)
(606)
7
8
**23
1
16
TOE
KICK
23
7
8
(606)
4
(102)
7
8
Wine Storage Model 424
A solid panel must not be
installed on a glass door unit, as
this may cause moisture to form
behind the panel.
OVERLAY PANELS
The door frame of the unit has pre-drilled holes for our
optional handle hardware. Refer to Hardware Considerations on page 8 for specifics about installing handle
hardware on this overlay application.
When planning to install the Model 424 next to adjoining
c
abinetry, you must make provisions to allow the door to
open to a maximum of 145˚ and not hit the door panel.
Refer to the full-scale illustration at the end of this section.
To give you a better idea of the exact space the Model 424
needs and how the panel fits in relationship with the unit,
refer to the chart and illustration below.
For additional specifications and installation information
specific to Model 424, refer to pages 2-5.
OVERLAY PANEL SPECIFICATIONS
3
Door P
anel (W x H)
23
/4" (603) x 301/16" (764)
Width of Rails and Stiles 21/4" (57) min
Door Panel Weight Limit 10 lbs (5 kg)
Panel Thickness
5
/8" (16) min
Dimensions in parentheses are in
millimeters unless otherwise specified.
7
Page 8
Planning Information
Wine Storage Model 424
When planning for hardware,
please refer to the Door Frame
Profile full-scale illustration on
the following page to give you a
better understanding of the
unit's frame and positioning of
the glass for the door. You must
not drill through the glass.
HARDWARE CONSIDERATIONS
With the Model 424 (overlay), you must supply your own
handle hardware. It is recommended you use our optional
handles and use the pre-drilled holes supplied to locate the
handles within the frame of our unit. The metal frame on
the door has numerous mounting holes on each side to
accommodate Sub-Zero accessory handles. This will allow
you to provide the best possible handle alignment and not
take away from the strength of the stile in this area after
the unit is used a number of times. We recommend using
a pull handle and not a pull knob.
If you elect to place different hardware on these units, we
encourage you to fasten the hardware by passing through
our door and attach the hardware through the Sub-Zero
door's frame.
Optional stainless steel handles are available in a variety of
diameters and lengths in the classic, platinum and carbon
stainless steel finishes and polished chrome. Contact
your Sub-Zero dealer for specifics. To obtain local dealer
information, visit the Locator section of our website,
subzero.com.
W OOD FA CING – WINE SHELVES
Sub-Zero has provided a natural cherry wood facing to
each of its wine shelves in each model. If, however, you
would like to replace these strips with wood more complementary to your design and surrounding cabinetry, you
can.
The Wine Shelf Wood Facing Dimensions illustration, on
page 10, can be used as a full-scale template. You must
follow the la
yout of this format to accommodate the
shelves properly. To remove the cherry strips, take the
shelves out and merely remove the screws. Reverse the
ocedure to affix the new wood
pr
.
If you choose to stain or seal the wood facing, be aware
that some of these substances are hazardous and will
damage stored wine.
Dimensions in parentheses are in
millimeters unless otherwise specified.
8
Page 9
Planning Information
1" (
25)
DOOR FRAME PROFILE
1" (
25)
21/4" (57) Rail/Stile
Glass
C
L
Cabinet Door
Profile
Wine Storage Model 424
WINE STORAGE DOOR FRAME
The full-scale illustration above shows a
oss-section of the Model 424 door
cr
frame profile.
Dimensions in parentheses are in
millimeters unless otherwise specified.
FULL-SCALE TEMPLATE
The full-scale illustr
ations on this page and the following
pages enable you to understand some of the unique situations you may face as you design the Wine Storage units
into homes. These templates can be easily photocopied or
acings.
used in y
our tr
IMPORTANT NOTE: Rails and stiles must be a minimum
1
2
of
/4" (57) wide
will be visible thr
ough the glass door will need to be
. The bac
k sides of r
ails and stiles that
finished.
9
Page 10
Planning Information
191/2" (495)
WIDTH
Maximum Thickness
FRONT VIEW
SIDE VIEW
11/2" (
38)
5
/8"
(
16)
7
/64"
(3)
5
/64"
(
2)
2
3
/64"
(9)
9
/16" (
14)
27
/32"
(
21)
Wine Storage Model 424
WINE SHELF WOOD FACING
Dimensions in parentheses are in
millimeters unless otherwise specified.
FULL-SCALE TEMPLATE
Use the full-scale illustr
ation above as a template if you
choose to replace the natural cherry wood facing with
wood more complementary to your design and surround-
binetry.
ing ca
10
Page 11
Wine Storage Model 424
DOOR PANEL
SUB-ZERO DOOR
145˚*
1
2
(13)
1
4
(6)
*
1
8
(3)
3
4
(19)
23 (587)
TO BACK OF
APPLIANCE
1
8
*
MODEL 424 MUST
EXTEND A MINIMUM
1/4"
(6) BEYOND THE
FRONT SURFACE OF
ADJOINING
CABINETRY TO
ALLOW THE MAXIMUM
DOOR SWING
SUB-ZERO
DOOR
DOOR
PANEL
24 (610)
CABINETRY
OPENING
23 (600)
DOOR PANEL
WIDTH
3
4
DOOR CLOSED AND 145˚ MAX OPENING
Planning Information
Dimensions in parentheses are in
millimeters unless otherwise specified.
11
Loading...