Sub-Zero WS30OLH, WS30O, 424GOLH, WS30STH, 424GORH Installation Guide
...
Wine Storage Installation Guide
WINE STORAGE
Contents
3 Wine Storage
4 Model 424G / 424FSG Site Preparation
7 Model 424G / 424FSG Installation
11 Model 427G / 427RG Site Preparation
14 Model 427G / 427RG Installation
18 Model WS-30 Site Preparation
25 Model WS-30 Installation
Features and specications are subject to change at any
time without notice. Visit subzero.com/specs for the most
up-to-date information.
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
IMPORTANT NOTE: Save these instructions for the local
electrical inspector.
WINE STORAGE
Product Information
Important product information including the model and
serial number are listed on the product rating plate. The
rating plate is located on the underside of the control panel,
on the left. Refer to the illustrations below.
If service is necessary, contact Sub-Zero factory certied
service with the model and serial number. For the name
of the nearest Sub-Zero factory certied service or for
questions regarding the installation, visit the contact & support section of our website, subzero.com or call Sub-Zero
customer care at 800-222-7820.
RATING PLATE
RATING PLATE
Tools and Materials
• Screwdrivers—standard, Phillips and Torx.
• Power drill.
• Drill bits (masonry bits required for concrete installation).
• Standard socket and wrench set.
• 2' and 4' levels.
• Material to protect home, ooring and cabinetry during
installation.
Full-size models.
Undercounter models.
subzero.com | 3
MODEL 424G / 424FSG SITE PREPARATION
SIDE
Opening Dimensions
MODEL 424G
341/2"
(876)
OPENING
HEIGHT
VIEW FRONT VIEW
OPENING WIDTH
24" (610)
OPENING
DEPTH
TOP VIEW
W
DUAL INSTALLATION
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom ller strip
require a dual installation kit. If a dual installation kit is not
specied, a 2"
(51) ller strip is recommended between units.
Dual installations without a ller strip can only be accomplished using two units with opposite hinges. Refer to the
illustrations below.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care
at 800-222-7820.
OPENING WIDTH W
424G 24"
(610)
DUAL OPENING WIDTH W
(610) Models 48
Two 24"
Dual installation kit required.
1
/8" (1222)
WITHOUT FILLER STRIP
Opposite hinges.
FILLER STRIP
Same side hinges.
4 | Sub-Zero Customer Care 800.222.7820
MODEL 424G / 424FSG SITE PREPARATION
Electrical
Installation must comply with all applicable electrical codes.
The electrical supply should be located within the shaded
area shown in the illustration below. A separate circuit,
servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause
interruption of operation.
IMPORTANT NOTE: The electrical outlet must be placed so
the grounding prong is to the right of the thinner blades.
The outlet must be ush with the back wall.
ELECTRICAL REQUIREMENTS
Electrical Supply 115 VAC, 60 Hz
Service 15 amp
Receptacle 3-prong grounding-type
WARNING
Do not use an extension cord, two-prong adapter or
remove the power cord ground prong.
Preparation
To operate properly, the door must open a minimum of 90°.
Use a minimum 3"
a 90° door opening.
Uncrate the unit and inspect for damage. Remove and
recycle packing materials. Do not discard the kickplate, antitip bracket, hardware and the leveling legs which hold the
wood base to the bottom of the unit.
(76) ller in corner installations to assure
LEFT SIDE
OF OPENING
2"
151/2"
(51)
Electrical supply location.
(394)
FLOOR
3" (76)
subzero.com | 5
MODEL 424G / 424FSG SITE PREPARATION
Anti-Tip Bracket
WARNING
To prevent the unit from tipping forward, the anti-tip
bracket must be installed.
MODEL 424G
The anti-tip bracket should be attached to the wall behind
1
the unit with the bracket ange located
/4" (6) above the top
of the unit. Refer to the illustration below. Failure to properly
position the anti-tip bracket will prevent proper engagement.
For installations that cannot accommodate the anti-tip
bracket, a countertop bracket is provided to secure the unit
to the countertop. Refer to the illustration below.
COUNTERTOP
BRACKET
1
/4" (6)
ANTI-TIP
BRACKET
MODEL 424FSG
The back of the anti-tip bracket must be installed 245/8"
(625)
from the front and centered behind the unit. Refer to
the illustration below. Refer to page 13 for wood and concrete oor applications.
ANTI-TIP BRACKET
Anti-tip bracket (424FSG).
Anti-tip bracket (424G).
6 | Sub-Zero Customer Care 800.222.7820
Countertop bracket.
MODEL 424G / 424FSG INSTALLATION
Custom Panel
MODEL 424G
For overlay applications, a custom door panel must be
installed. Panel size is critical for a proper t. To verify panel
requirements and dimensions, refer to the Sub-Zero design
guide at subzero.com/specs.
Finish all sides of the custom panel. They may be visible
when the door is open or through the glass door.
The custom overlay door panel is attached using screws
provided, through the door frame. Screw locations are
marked on the back of the custom panel using tenon centers inserted into holes of the door frame.
With the unit secured and door closed, hold the custom
panel in desired position on the door. Lightly tap the front
of the panel to locate mounting positions. Remove tenon
centers. Refer to the illustration below.
The door frame has mounting holes to accommodate
Sub-Zero accessory handles. If handle mounting holes are
not utilized, the handle should be attached to the custom
panel prior to mounting. Screw heads may need to be countersunk into the panel for proper alignment.
To mount the custom panel, open the door and use predrilled holes to position the panel. Drive screws into the
panel through black tape on the door frame. Screw holes
are hidden behind the door gasket. Use as many screws as
necessary to secure the custom panel. Refer to the illustration below.
Adjustments can be made to the custom panel with a few
mounting screws in place, but not fully tightened. Once the
proper position is achieved, install and secure all screws.
Cover holes on the inside of the door frame with the cover
patches or plugs provided.
CAUTION
A solid panel cannot be installed over the glass door. A
solid door is available through an authorized Sub-Zero
dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com.
Tenon center.
DOOR
FRAMEPANEL
TENON CENTER
GASKET
Door frame cross section.
13
/32" (11)
DIAMETER
GLASS
1
/4" (6)
DIAMETER
subzero.com | 7
MODEL 424G / 424FSG INSTALLATION
Placement
CAUTION
Before moving the unit into position, secure the door
closed and protect any nished ooring.
Use an appliance dolly to move the unit near the opening.
If the unit has been on its back or side, it must stand upright
for a minimum of 24 hours before connecting power.
If the unit will be connected to a home security system,
run lead wires through the compressor compartment prior
to positioning the unit. Refer to page 9. Once the unit is in
position, wiring connection can be completed from the front.
Alignment
LEVELING
Level the unit before sliding it into position. Turn each of the
four leveling legs clockwise to raise the unit and counterclockwise to lower. Refer to the illustration below.
DOOR ADJUSTMENT
The top and bottom cabinet hinges are held in place with
three permanent adjustment screws. For adjustments,
loosen the screws, adjust the door and tighten screws.
Refer to the illustration below. For model 424FSG, only the
bottom door hinge can be adjusted.
SCREW
HINGEADJUSTMENT
LEVELING LEGS
Leveling.
Door adjustment.
8 | Sub-Zero Customer Care 800.222.7820
MODEL 424G / 424FSG INSTALLATION
Completion
Plug the power cord into the grounded outlet, then slide
the unit into position. Verify the anti-tip bracket is properly
engaged.
1
It may be necessary to install the unit
/4" (6) beyond the
front surface of adjacent cabinetry, to prevent interference
when the door is opened to 145°. Refer to the full-scale
template on page 10.
HOME SECURITY CONNECTION
If the unit will be connected to a home security system,
make connections to the leads shown in the illustration
below. Refer to the following color codes:
• Normally open contacts—white with red stripe wire.
• Normally closed contacts—white with blue stripe wire.
• Common—gray with white stripe wire.
Use the spade terminals or wire nuts provided to make
proper wiring connections.
CAUTION
The alarm circuit in the unit is intended as a lowvoltage, low-current device only. It should not be used
to switch line power. Any unused terminals should be
completely insulated and all wires should be secured
away from conductive or moving components.
ANCHORING
To anchor, use the countertop bracket provided to secure
the unit to the underside of the countertop. Refer to the
illustration below. If the countertop bracket can not be
utilized, install shims along the top and sides of the unit.
KICKPLATE INSTALLATION
Install the kickplate using the two screws provided. Refer
to the illustration below. The kickplate must be removable
for service. The oor cannot interfere with removal. Do not
cover the louvered section of the kickplate.
COUNTERTOP
BRACKET
KICKPLATE
Anchoring.
Kickplate installation.
HOME SECURITY
LEADS
Home security connection.
subzero.com | 9
MODEL 424G / 424FSG INSTALLATION
Door Clearance
FULL-SCALE TEMPLATE
To allow for a 145° door opening, the unit should extend
1
a minimum of
/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed ush, however,
there is potential for interference with the panel if the
door is opened past 90°.
UNDERCOUNTER
UNIT
DOOR CLOSED
1
/2"
(13)
ADJACENT
CABINETRY
3
/4" (19) DOOR PANEL
1" (25)0"
SCALE
145° door opening (top view).
10 | Sub-Zero Customer Care 800.222.7820
1
/4"
(6)
1
/8" (3)
HINGE AT 145°
OPENING
(DOOR OPENS PAST 145°)
MODEL 427G / 427RG SITE PREPARATION
SIDE
Opening Dimensions
MODELS 427G AND 427RG
H
OPENING
HEIGHT
25" (635)
OPENING
DEPTH
TOP VIEW
W
OPENING WIDTH
DUAL INSTALLATION
When installing two units side by side in a dual installation, the opening width is determined by adding the single
opening widths together. A dual installation kit is required,
but does not affect the opening width.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care
at 800-222-7820.
VIEW
FRONT VIEW
OPENING W H
427G 27"
(686) 80" (2032)
427RG 27" (686) 80" (2032)
The depth of models 427G and 427RG is 24" (610). Allow for
panel thickness when planning the nished opening depth.
subzero.com | 11
MODEL 427G / 427RG SITE PREPARATION
Electrical
Installation must comply with all applicable electrical codes.
The electrical supply must be located within the shaded
area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit
interrupter (GFCI) is not recommended and may cause interruption of operation.
The electrical outlet must be positioned with the grounding
prong to the right of the thinner blades.
ELECTRICAL REQUIREMENTS
Electrical Supply 115 VAC, 60 Hz
Service 15 amp
Receptacle 3-prong grounding-type
CAUTION
The outlet must be checked by a qualied electrician to
be sure that it is wired with the correct polarity. Verify
that the outlet is properly grounded.
WARNING
Do not use an extension cord, two-prong adapter or
remove the power cord ground prong.
Preparation
Uncrate the unit and inspect for damage. Remove the wood
base and discard shipping bolts and brackets. Remove and
recycle packing materials. Do not discard the kickplate, antitip bracket and hardware.
IMPORTANT NOTE: For model 427RG, the upper drawer has
a control cable that must be disconnected before removing
the drawer. Refer to the illustration below.
Control cable (model 427RG).
LEFT SIDE
OF OPENING
21/2"
(64)
13" (330)
41/2"
(
)
114
1
/4"
(6)
Electrical supply location.
12 | Sub-Zero Customer Care 800.222.7820
FLOOR
MODEL 427G / 427RG SITE PREPARATION
Anti-Tip Bracket
WARNING
To prevent the unit from tipping forward, the anti-tip
bracket must be installed.
The back of the anti-tip bracket must be installed 24" (610)
from the front of the unit (without panels).
Use all anti-tip bracket hardware as instructed for wood or
concrete oors.
IMPORTANT NOTE: For wood or concrete oor applications,
if the #12 screws do not hit a wall stud or wall plate, use the
#8 screws and #12 washers with the wall anchors.
IMPORTANT NOTE: In some installations the subooring or
nished oor may necessitate angling the screws used to
fasten the anti-tip bracket to the back wall.
ANTI-TIP HARDWARE
1 Anti-tip bracket
1
12 #12 x 2
4
12 #12 at washers
4 #8–18 x 1
4 Nylon Zip-it
/2" pan head screws
3
/8"–16 x 33/4" wedge anchors
1
/4" truss head screws
®
wall anchors
WOOD FLOOR
After properly locating the anti-tip bracket in the opening,
3
drill pilot holes
/16" (5) diameter maximum in the wall studs
or wall plate. Use the #12 screws and washers to secure the
brackets. Verify the screws penetrate through the ooring
material and into wall studs or wall plate a minimum of
3
/4" (19). Refer to the illustration and chart below.
CONCRETE FLOOR
After properly locating the anti-tip bracket in the opening,
3
drill pilot holes
or wall plate. Drill
a minimum of 1
washers to secure the brackets to the wall, and use the
/16" (5) diameter maximum in the wall studs
3
/8" (10) diameter holes into the concrete
1
/2" (38) deep. Use the #12 screws and
3
/8"
wedge anchors to secure the brackets to the oor. Verify
the screws penetrate wall studs or wall plate a minimum of
3
/4" (19). Refer to the illustration and chart below.
ANTI-TIP BRACKET
MODEL A
427G and 427RG 131/2" (343)
WALL PLATE
SUBFLOORING
Wood oor.
A
FINISHED
FLOORING
WOOD FLOOR
A
A
WALL PLATE
SUBFLOORING
CONCRETE
FLOOR
A
FINISHED
FLOORING
11/2"(38)
min
Concrete oor.
subzero.com | 13
MODEL 427G / 427RG INSTALLATION
Anti-Tip Bracket
CONCRETE WEDGE ANCHOR INSTALLATION
1 Drill a
2 Assemble the washer and nut ush with the end of
3 Expand the anchor by tightening the nut 3–5 turns past
Verify there are no electrical wires or plumbing in the
area which the screws could penetrate.
Always wear safety glasses and use other necessary
protective devices or apparel when installing or working
with anchors.
Anchors are not recommended for use in lightweight
masonry material such as block or brick, or for use in
new concrete which has not had sufcient time to cure.
The use of core drills is not recommended to drill holes
for the anchors.
3
/8" (10) diameter hole any depth exceeding the
minimum embedment. Clean the hole or drill additional
depth to accommodate drill nes.
anchor to protect threads. Drive the anchor through the
material to be fastened until the washer is ush with the
surface material.
hand-tight position or to 25 ft-lb of torque.
WARNING
CAUTION
Custom Panels
For models 427G and 427RG, custom panels and handle
hardware must be installed. Stainless steel panels are
available through an authorized Sub-Zero dealer. For local
dealer information, visit the nd a showroom section of our
website, subzero.com.
PANEL REQUIREMENTS
PANEL WEIGHT MAX
Door 20 lb (9 kg)
Drawer (427RG) 12 lb (5 kg)
PANEL THICKNESS MIN
All Panels
Reveals between panels can vary, 1/8" (3) reveals are typical.
CAUTION
When using a panel thicker than 3/4" (19) with reveal less
1
than
/4" (6), panel may cause damage to the unit when
door is opened to 105°. Use the built-in 90° door stop.
CAUTION
As reveals between cabinetry and the unit decrease,
severe nger pinching can occur while door is closing.
Finish all sides of the custom panel. They may be visible
when the door is open or through the glass door.
5
/8" (16)
14 | Sub-Zero Customer Care 800.222.7820
D-style handles are recommended. Stainless steel tubular
and pro handles are avail able through an authorized
Sub-Zero dealer. For local dealer information, visit the nd
a showroom section of our website, subzero.com. The door
handle must be located near the edge of the panel opposite
the hinge and should be centered top to bottom.
CAUTION
A solid panel cannot be installed over the glass door. A
solid door is available through an authorized Sub-Zero
dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com.
MODEL 427G / 427RG INSTALLATION
Panel Installation
The custom overlay door panel is attached using screws
provided through the door frame. Screw locations are
marked on the back of the custom panel using tenon centers inserted into holes of the door frame.
With the unit secured and door closed, hold the custom
panel in desired position on the door. Lightly tap the front
of the panel to locate mounting positions. Remove tenon
centers. Refer to the illustration below.
The door frame has mounting holes to accommodate
Sub-Zero accessory handles. If handle mounting holes are
not utilized, the handle should be attached to the custom
panel prior to mounting. Screw heads may need to be countersunk into the panel for proper alignment.
To mount the custom panel, open the door and use predrilled holes to position the panel. Drive screws into the
panel through black tape on the door frame. Screw holes
are hidden behind the door gasket. Use as many screws as
necessary to secure the custom panel. Refer to the illustration below.
Adjustments can be made to the custom panel with a few
mounting screws in place, but not fully tightened. Once the
proper position is achieved, install and secure all screws.
Cover holes on the inside of the door frame with the cover
patches or plugs provided.
DRAWER PANELS (MODEL 427RG)
Remove the mounting hardware attached to the front of the
unit and set aside. Place the panel face down on a protected work surface.
Position the top edge of the template ush with the top
edge of the panel. Depending on the height and thickness of
the lower drawer panel, the bracket may need to be inverted
for proper placement. Mark and drill pilot holes, then secure
1
brackets to panel using the #8 x
/2" screws provided. Refer
to the illustration below.
To help with placement of drawer panels, examine the lower
L-bracket and panel to determine the slotted holes on the
bracket that will be used. Then position screws into the
lower portion of the drawer that correspond with these slots.
Leave the screws out slightly so the slotted holes will slide
under the heads.
Install the panel by engaging the tabbed bracket to the top
of the drawer, then rotate the panel until the lower bracket
is properly positioned below the drawer. The panel can be
1
adjusted
/4" (6) up and down and side to side.
Once the panel is properly aligned, attach the remaining
1
/2" screws to the mounting bracket.
#10 x
Reconnect the control cable before reinstalling the top
drawer. Refer to page 12.
Tenon center.
DOOR
FRAMEPANEL
TENON CENTER
GASKET
Door frame cross section.
13
/32" (11)
DIAMETER
GLASS
1
/4" (6)
DIAMETER
TEMPLATE FLUSH WITH
TOP OF PANEL
SIDE
EDGE GAP
WILL VARY
BACK OF PANEL
Template position.
TABBED BRACKET
L BRACKET
Drawer panel installation.
subzero.com | 15
MODEL 427G / 427RG INSTALLATION
Placement
CAUTION
Before moving the unit into position, secure the door/
drawers closed and protect any nished ooring.
Use an appliance dolly to move the unit near the opening.
Front and rear leveling legs can be adjusted from the front
once the unit is positioned.
If the unit has been on its back or side, it must stand upright
for a minimum of 24 hours before connecting power.
If the unit will be connected to a home security system, run
lead wires through the compressor compartment prior to
positioning the unit. Refer to page 17. Once the unit is in
position, wiring connection can be completed from the front.
Plug the power cord into the grounded outlet, then slide
the unit into position. Verify the anti-tip bracket is properly
engaged.
Alignment
LEVELING
Once the unit is in position, height adjustment can be made
from the front. Using a standard screwdriver, turn front
leveling legs clockwise to raise the unit or counterclockwise
to lower. Using a Phillips drive, turn rear adjustment screws
clockwise to raise the unit or counterclockwise to lower. Use
the lowest torque setting when using a power drill (18 revolutions equals
rear leveling legs by hand. Refer to the illustrations below.
Level the unit to the oor, not surrounding cabinetry. This
could affect the operation of the unit, such as door closing.
When the unit is properly leveled, door/drawer adjustments
are less likely to be necessary.
Secure the unit in place using the side mounting clips and
1
/2" screws provided.
#8 x
WARNING
To reduce the possibility of the unit tipping forward,
the front leveling legs must be in contact with the oor.
1
/16" of height adjustment). Do not turn the
16 | Sub-Zero Customer Care 800.222.7820
Front adjustment.
Rear adjustment.
MODEL 427G / 427RG INSTALLATION
Completion
TRIM INSTALLATION
Install decorative trim strips to the top and sides of the unit.
Attach the top trim using the double-sided velcro, then snap
side trim over brackets on the sides of the unit. Refer to the
illustration below.
HOME SECURITY CONNECTION
If the unit will be connected to a home security system,
make connections to the leads shown in the illustration
below. Refer to the following color codes:
• Normally open contacts—white with red stripe wire.
• Normally closed contacts—white with blue stripe wire.
• Common—gray with white stripe wire.
Use the spade terminals or wire nuts provided to make
proper wiring connections.
CAUTION
The alarm circuit in the unit is intended as a lowvoltage, low-current device only. It should not be used
to switch line power. Any unused terminals should be
completely insulated and all wires should be secured
away from conductive or moving components.
KICKPLATE INSTALLATION
Install the kickplate using the screws provided. The
mounting bracket may be adjusted slightly for a ush t. The
kickplate must be removable for service. The oor cannot
interfere with removal. Refer to the illustration below.
A decorative kickplate can be added to the factory-installed
kickplate but cannot block the kickplate louvers.
Turn power on by touching POWER on the control panel.
90° DOOR STOP
The door opens to 105°. A 90° door stop is built into the
hinge system for installations where the door opening must
be limited.
To engage the door stop, use a standard screwdriver and
rotate the center cam of the hinge. The adjustment must be
made to both upper and lower hinges. Refer to the illustration below.
HOME SECURITY
LEADS
Home security connection.
SIDE TRIM
Trim installation.
TOP TRIM
Kickplate installation.
MOUNTING
BRACKET
90° door stop.
subzero.com | 17
MODEL WS-30 SITE PREPARATION
NOTE: Shaded line represents profile of unit.
SIDE
Opening Dimensions
STANDARD INSTALLATION
24" (610)
OPENING
DEPTH
TOP VIEW
W
OPENING WIDTH
FRONT VIEW
VIEW
833/4"
(2127)
OPENING
HEIGHT
OPENING WIDTH W
1
WS-30 29
/2" (749)
If two units are installed side by side, refer to page 20.
18 | Sub-Zero Customer Care 800.222.7820
MODEL WS-30 SITE PREPARATION
*3
NOTE: Shaded line represents profile of unit with
SIDE
Opening Dimensions
FLUSH INSET INSTALLATION
263/16"
(665)
FLUSH
INSET
23/16"
DEPTH
(56)
TOP VIEW
FINISHED
CLEATS*
1
/4"
(6)
84"
(2134)
FLUSH
INSET
HEIGHT
VIEW
" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
3/4" (19) panel.
11/4"
(32)
FLUSH INSET WIDTH
FRONT VIEW
W
4" (102)
11/4"
(32)
3"
(76)*
TYPICAL
23/16"
(56)
FLUSH INSET WIDTH W
WS-30 32"
(813)
Dimensions assume a 3/4" (19) panel thickness. If two units
are installed side by side, refer to page 21.
subzero.com | 19
MODEL WS-30 SITE PREPARATION
NOTE: Shaded line represents profile of unit.
SIDE
Opening Dimensions
DUAL STANDARD INSTALLATION
24" (610)
OPENING
DEPTH
TOP VIEW
VIEW
833/4"
(2127)
OPENING
HEIGHT
OPENING WIDTH
OPENING WIDTH W
3
WS-30 and 30" Built-In Model 59
/4" (1518)
WS-30 and 36" Built-In Model 653/4" (1670)
W
FRONT VIEW
A dual installation kit will be required for this installation.
20 | Sub-Zero Customer Care 800.222.7820
MODEL WS-30 SITE PREPARATION
*3
NOTE: Shaded line represents profile of unit with
SIDE
Opening Dimensions
DUAL FLUSH INSET INSTALLATION
263/16"
(665)
FLUSH
INSET
23/16"
DEPTH
(56)
TOP VIEW
FINISHED
CLEATS*
1
/4"
(6)
84"
(2134)
FLUSH
INSET
HEIGHT
VIEW
" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
3/4" (19) panel.
11/4"
(32)
FLUSH INSET WIDTH
FRONT VIEW
W
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
23/16"
(56)
FLUSH INSET WIDTH W
WS-30 and 30" Built-In Model 62
WS-30 and 36" Built-In Model 681/4" (1734)
1
/4" (1581)
Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.
subzero.com | 21
MODEL WS-30 SITE PREPARATION
Dual Installation
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom ller strip
require a dual installation kit. If a dual installation kit is not
specied, a 2"
Dual installations without a ller strip can only be accomplished using two units with opposite hinges. Refer to the
illustrations below.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care
at 800-222-7820.
(51) ller strip is recommended between units.
Electrical
Installation must comply with all applicable electrical codes.
The electrical supply should be located within the shaded
area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit
interrupter (GFCI) is not recommended and may cause interruption of operation.
ELECTRICAL REQUIREMENTS
Electrical Supply 115 VAC, 60 Hz
Service 15 amp
Receptacle 3-prong grounding-type
CAUTION
The outlet must be checked by a qualied electrician to
be sure that it is wired with the correct polarity. Verify
that the outlet is properly grounded.
WARNING
Do not use an extension cord, two-prong adapter or
remove the power cord ground prong.
WITHOUT FILLER STRIP
Opposite hinges.
FILLER STRIP
Same side hinges.
7"
E
(178)
6"
(152)
751/2" (1918)
FROM FLOOR
RIGHT SIDE
OF OPENING
Electrical supply location.
22 | Sub-Zero Customer Care 800.222.7820
MODEL WS-30 SITE PREPARATION
Preparation
Uncrate the unit and inspect for damage. Remove the wood
base and discard shipping bolts and brackets. Remove and
recycle packing materials. Do not discard the kickplate, antitip brackets and hardware.
Completely retract the front leveling legs to allow the unit to
be moved into position. The front and rear leveling legs can
be adjusted from the front once the unit is in position.
Remove the drain pan to avoid damage, and allow for
proper appliance dolly placement.
The grille assembly should be removed prior to moving the
unit. To remove, pull out on the bottom edge of the grille and
rotate upward. Loosen the two back grille mounting screws
and remove the two front grille mounting screws. With the
grille held rmly, pull forward to remove. Refer to the illustrations below.
Grille removal.
BACK GRILLE
SCREW
Grille mounting screws.
ADJUSTMENT
FRONT
GRILLE SCREW
SCREWS
GRILLE
subzero.com | 23
MODEL WS-30 SITE PREPARATION
Anti-Tip Bracket
WARNING
To prevent the unit from tipping forward, the anti-tip
brackets must be installed.
The two anti-tip brackets must be installed exactly 24"
(610)
from the front of the opening to the back of the
brackets and a minimum of 4"
opening. This depth will increase to 26
inset installation, based on
(102) from the sides of the
3
3
/4" (19) thick panels. Failure to
/16" (665) for a ush
properly position the anti-tip brackets will prevent proper
engagement.
Use all anti-tip bracket hardware as instructed for wood or
concrete oors.
IMPORTANT NOTE: For wood or concrete oor applications,
if the #12 screws do not hit a wall stud or wall plate, use the
#8 screws and #12 washers with the wall anchors.
IMPORTANT NOTE: In some installations the subooring or
nished oor may necessitate angling the screws used to
fasten the anti-tip brackets to the back wall.
ANTI-TIP HARDWARE
2 Anti-tip brackets
1
12 #12 x 2
4
12 #12 at washers
4 #8–18 x 1
4 Nylon Zip-it
/2" pan head screws
3
/8"–16 x 33/4" wedge anchors
1
/4" truss head screws
®
wall anchors
WOOD FLOOR
After properly locating the anti-tip brackets in the opening,
3
drill pilot holes
/16" (5) diameter maximum in the wall studs
or wall plate. Use the #12 screws and washers to secure the
brackets. Verify the screws penetrate through the ooring
3
material and into wall studs or wall plate a minimum of
(19)
. Refer to the illustration below.
/4"
CONCRETE FLOOR
After properly locating the anti-tip brackets in the opening,
3
drill pilot holes
or wall plate. Drill
a minimum of 1
washers to secure the brackets to the wall, and use the
/16" (5) diameter maximum in the wall studs
3
/8" (10) diameter holes into the concrete
1
/2" (38) deep. Use the #12 screws and
3
/8"
wedge anchors to secure the brackets to the oor. Verify the
3
24"
(610)
4" (102)
MIN
/4"
screws penetrate wall studs or wall plate a minimum of
(19)
. Refer to the illustration below.
24"
(610)
4" (102)
MIN
24 | Sub-Zero Customer Care 800.222.7820
WALL PLATE
SUBFLOORING
Wood oor.
FINISHED
FLOORING
WOOD FLOOR
WALL PLATE
WALL PLATE
SUBFLOORING
SUBFLOORING
CONCRETE
CONCRETE
FLOOR
FLOOR
Concrete oor.
FINISHED
FINISHED
FLOORING
FLOORING
11/2"(38)
11/2"(38)
min
MIN
MODEL WS-30 INSTALLATION
Anti-Tip Bracket
CONCRETE WEDGE ANCHOR INSTALLATION
1 Drill a
2 Assemble the washer and nut ush with the end of
3 Expand the anchor by tightening the nut 3–5 turns past
Verify there are no electrical wires or plumbing in the
area which the screws could penetrate.
Always wear safety glasses and use other necessary
protective devices or apparel when installing or working
with anchors.
Anchors are not recommended for use in lightweight
masonry material such as block or brick, or for use in
new concrete which has not had sufcient time to cure.
The use of core drills is not recommended to drill holes
for the anchors.
3
/8" (10) diameter hole any depth exceeding the
minimum embedment. Clean the hole or drill additional
depth to accommodate drill nes.
anchor to protect threads. Drive the anchor through the
material to be fastened until the washer is ush with the
surface material.
hand-tight position or to 25 ft-lb of torque.
WARNING
CAUTION
Custom Panels
For overlay and ush inset applications, custom door and
grille panels must be installed. Panel size is critical for a
proper t. To verify panel requirements and dimensions,
refer to the Sub-Zero design guide at subzero.com/specs.
IMPORTANT NOTE: Flush inset applications require a
minimum
Finish all sides of the custom panel. They may be visible
when the door is open or through the glass door.
A solid panel cannot be installed over the glass door.
1
/2" (13) reveal on all sides.
CAUTION
subzero.com | 25
MODEL WS-30 INSTALLATION
Panel Installation
DOOR PANEL
To install the custom door panel, remove the handle side
trim molding. Insert a screwdriver tip into the top corner slot
on the handle side and pop out the trim. Remove the screws
and frame. Refer to the illustration below.
1
The door has a
into. If the panel is thicker than a
around the panel or mount the panel on a sheet of
/4" (6) frame for the custom panel to slide
1
/4" (6), rout an edge
1
/4" (6)
thick material, then insert into the frame.
Door side trim.
(3) space is required between the backer panel and
A .10"
the custom panel to allow the panel to slide into the door
frame. Refer to the illustrations below for critical dimensions.
Install handle hardware before inserting the panel. Large
D-style handles are recommend rather than knobs. Screw
heads must be countersunk into the panel.
Slide the panel into the frame.
To reinstall the door trim molding, insert the top of the trim
into grooves at the top of the door and work downward,
snapping the trim into clips on the door frame.
SPACER PANEL
CUSTOM PANEL
BACKER PANEL
TRIM
5
/16" (8) min
1
/8" (3) (OVERLAY)
Panel assembly cross section
(overlay).
CUSTOM
PANEL
3
/4"
(19)
.10" (3)
typical
Panel assembly rear view.
1
/4" (6)
SPACER
PANEL
BACKER
PANEL
26 | Sub-Zero Customer Care 800.222.7820
MODEL WS-30 INSTALLATION
84"
(2134)
24"
(610)
OPTIONAL
TOE KICK
CUT-OUT
4" (102)
17/8"(48)
1" (25)
ROUT TO
1
/8"
(3)
FRONT
OF SIDE
PANEL
25/8"
(67)
MAIN
FRAME
SIDE PANEL
ROUTING
1" (25)
17/8" (48)
1
/8" (3)
1
/2" (13)
Panel Installation
GRILLE PANEL
Remove the bottom grille frame by extracting the lower
two corner screws from each side of the grille assembly.
Refer to the illustration below.
With the bottom section removed, slide the custom grille
1
panel into the frame. If the panel is thinner than
/4" (6), a
ller material will need to be installed to achieve a proper
t. Once the panel is installed, reattach the bottom grille
frame by sliding the corner brackets back into position, then
reinstall the four corner screws.
BOTTOM
GRILLE
FRAME
SIDE PANEL
When installing a custom side panel, an accessory kit is
required and is available through an authorized Sub-Zero
dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. Stainless steel
and white enamel side panels are also available from an
authorized Sub-Zero dealer.
IMPORTANT NOTE: The use of side panels may change the
width of the opening.
A custom side panel must be a minimum of 24"
1
/2" (13) thick. Routing will be necessary for the side
and
(610) deep
panel to t ush against the side of the unit. Refer to the
illustrations below.
IMPORTANT NOTE: The height of the side panel will vary
with the height of the grille. Verify the nished height before
modifying panels.
Grille frame assembly.
Routing detail.
Side panel dimensions.
subzero.com | 27
MODEL WS-30 INSTALLATION
Placement
CAUTION
Before moving the unit into position, secure the door
closed and protect any nished ooring.
Use an appliance dolly to move the unit near the opening.
If the unit has been on its back or side, it must stand upright
for a minimum of 24 hours before connecting power.
If the unit will be connected to a home security system, run
lead wires through the compressor compartment prior to
positioning the unit. Refer to page 30. Once the unit is in
position, wiring connection can be completed from the front.
Plug the power cord into the grounded outlet, then roll the
unit into position. Verify the anti-tip brackets are properly
engaged.
IMPORTANT NOTE: If used, side panels will need to be
installed before the unit is placed in its nal position. Refer
to page 27.
Alignment
LEVELING
Once the unit is in position, turn the front leveling legs
clockwise to adjust the height. The rear height adjustment
can be made from the front of the roller base. Using a
3
socket, turn the
/8" hex bolt clockwise to raise the unit or
counterclockwise to lower. Use the lowest torque setting
when using a power drill. Do not turn the rear leveling legs
by hand. Refer to the illustration below.
When the unit is properly leveled, door adjustments are less
likely to be necessary.
IMPORTANT NOTE: Level the unit to the oor, not sur-
rounding cabinetry. This could affect the operation of the
unit, such as door closing.
WARNING
To reduce the possibility of the unit tipping forward, the
front leveling legs must be in contact with the oor.
3
/8"
28 | Sub-Zero Customer Care 800.222.7820
Leveling.
FRONT
LEVELING LEG
REAR
ADJUSTMENT
Loading...