Sub-Zero 315W User Manual

INSTALLATION GUIDE

Model 315W Wine Storage

Contents

Important Note

Model 315W Wine Storage . . . . . . . . . . . . . . . . . . . . . 3

Model 315W Specifications . . . . . . . . . . . . . . . . . . . . . 4

odel 315W Installation . . . . . . . . . . . . . . . . . . . . . . . 6

M

Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . 10

Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Features and specifications are subject to change at any time
without notice. Visit subzero.com/ specs for the most up-to­date information.

IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specified.

o ensure the safe and efficient installation of Sub-Zero

T
equipment, please take note of the following types of
highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially
relevant to a problem-free installation.

CAUTION signals a situation where minor injury or product
damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or
death if precautions are not followed.

Sub-Zero Model 315W Wine Storage 3

subzero.com/specs

Model 315W Wine Storage

IMPORTANT NOTE: T

he importance of the installation
of the undercounter wine storage unit cannot be overem­phasized. Installation must be completed by a qualified
installer.

Read this entire installation guide prior to installation.
There are key details that you should observe during the
installation to make the process easier, problem-free and,
most importantly, safe. The homeowner should keep this
installation guide for future reference.

Any questions or problems regarding the installation
should be directed to your authorized Sub-Zero dealer or
Sub-Zero customer care at 800-222-7820. You may also
check the contact & support sectionofour website,
subzero.com.

Important product information, including the model and
serial number of your unit are listed on the product rating
plate, located on the underside of the top wall. Refer to
the illustration.

ATING PLATE

R

Location of rating plate.

Model 315W Specifications 4

1

5

1

/8" (

384)

2

4"

(

610)

3

4

1

/16"

(865)

165/8"

(422)

4" (102)

13/4" (44)

24" (610)

OPENING

DEPTH

151/4"

(387)

OPENING

WIDTH

24" (610)

OPENING DEPTH

341/2" (876)

OPENING

HEIGHT

TOP VIEW

FRONT VIEWSIDE VIEW

Model 315W Specifications

OVERALL DIMENSIONS

INSTALLATION

Overall dimensions are based on stainless steel panels
and handles.

NOTE: Door swing is not reversible.

Specifications

Wine Storage Capacity 26 bottles (750 ml)

Shipping Weight 118 lbs (54 kg)

IMPORTANT NOTE:

It is recommended that the electrical
supply be placed in an adjacent cabinet. If it is placed
within the opening, additional cabinet depth may be
required.

Model 315W Specifications 5

E

E

E

GROUNDING

PLUG

GROUNDED

ELECTRICAL OUTLET

subzero.com/specs

Area Requirements

efore moving the unit into place, make sure the opening

B
dimensions, door clearance and electrical service are
correct. Refer to the illustrations on the previous page.

IMPORTANT NOTE: For corner installations, door swing

may be limited due to handle contact with the adjacent
wall or cabinet. You must allow a minimum of 2"
the wall for a 90˚ door opening. This will ensure that the
wine shelves can be fully extended.

Wine bottles are heavy. A fully loaded unit will weigh
over 200 lbs

(91 kg). Be sure the subflooring is adequate

for the weight of both the unit and its contents.

Model 315W is intended for indoor use only.

(51) from

Electrical Requirements

odel 315W must be installed with adequate clearance

M
for electrical connection at the rear of the unit. The elec­trical supply requires installation of a grounded receptacle
on a separate circuit, servicing only this appliance. A
ground fault circuit interrupter (GFCI) is not recommended
and may cause interruption of operation. Follow the
National Electrical Code and local codes and ordinances
when installing the receptacle.

IMPORTANT NOTE: Although it can be located anywhere

on the back wall, it is recommended that the receptacle be
placed in an adjacent cabinet or in the lower right of the
opening. If it is placed within the opening, additional
cabinet depth may be required. Refer to the illustrations
below.

Do not use an extension cord or two-prong adapter.
Electrical ground is required on this appliance.

Electrical Requirements

Power Supply 115 V AC, 60 Hz

Receptacle 3-prong grounding-type

Circuit Breaker 15 amp

Location of electrical supply. Electrical ground.

Model 315W Installation 6

ANTI-TIP BRACKET

Unpack the Unit

efore moving the wine storage unit into position, make

B
sure the opening dimensions and electrical requirements
are complete and accurate.

IMPORTANT NOTE: The floor under the wine storage unit

must be at the same level as the surrounding finished floor
to allow for removal of the unit for servicing.

Use an appliance dolly to move the wine storage unit near
the installation opening. Position the dolly at the side of
the unit to prevent damage to finished surfaces. Remove
and discard all packing materials and tape.

IMPORTANT NOTE: Do not discard the kickplate, anti-tip

bracket and hardware. These items will be needed for the
installation.

The roller-assembly wine shelves should be removed to
reduce weight and prevent them from rolling. To remove,
pull the shelf out to its full extension, gently and evenly lift
up on both sides of the front of the shelf and remove.
Reverse the procedure to reinstall the shelf.

Anti-Tip Bracket

To prevent the unit from tipping forward and provide a
stable installation, the unit must be secured in place
with the anti-tip bracket.

An anti-tip bracket and hardware is provided with model
315W. Placement of the anti-tip bracket is critical to a
stable installation. The anti-tip bracket must be installed
securely.

Attach the anti-tip bracket to the top of the unit, opposite
the hinge side. The bracket offset flange should be facing
up with the two oblong holes in the front. Once the unit is
moved into position, open the door and secure the anti-tip
bracket to the countertop. Refer to illustration below.

Before moving the wine storage unit into position,
protect any finished flooring with appropriate materials
and secure the door closed.

Anti-tip bracket.

Model 315W Installation 7

LEVELING

LEG

subzero.com/specs

Installation

IMPORTANT NOTE: I

f the wine storage unit has been laid
on its back or side, you must allow the unit to stand
upright for a minimum of 24 hours before connecting
power.

With the wine storage unit near the installation opening,
plug the power supply cord into the electrical outlet. With
power applied to the unit, check for lighting and cooling.
Once you are satisfied that the unit is operating properly,
shut off power to the electrical outlet at the circuit breaker
and proceed.

Shut off power to the electrical outlet.

LEVEL THE UNIT

Level the wine storage unit before sliding it into position.
Leveling cannot be completed with the unit pushed back
in the installation opening.

Using an adjustable wrench or pliers, turn each of the four
leveling legs clockwise to raise the unit and counterclock­wise to lower the unit. For the location of the leveling legs,
refer to the illustration below.

o determine the horizontal or vertical level point, place a

T
2'

(.6 m) level along the top of the unit or on either exterior

side of the unit. In order to access these leveling posi­tions, the unit will have to be slightly out of the opening.

To reduce the possibility of the unit tipping forward, the
front leveling legs must be in contact with the floor.

POSITION THE UNIT

Slide the wine storage unit back into position in the
installation opening.

IMPORTANT NOTE: Model 315W has been designed to be

serviced in place, but in some cases it may be necessary
to pull the unit out for service.

If a floor is to be installed after the unit has been installed,
spacing shims equal to the thickness of the floor should
be installed under the unit to keep it level with the floor.

Turn power back on to the electrical outlet.

Adjust leveling legs.

Model 315W Installation 8

KICKPLATE

O
F
F

O
N

C

O

L

D

E

S

T

WARM AIR

OUT

ROOM AIR IN

Kickplate

INSTALL KICKPLATE

Once the wine storage unit is in position, install the kick­plate using the screws provided. Refer to the illustration.
There is some adjustment to the mounting assembly so
that the kickplate will fit flush with the surrounding area.

The kickplate must be removed for servicing. The floor
cannot interfere with removal. Do not cover the vents of
the kickplate to allow proper airflow.

If you choose, the kickplate may be painted another color.
Follow these steps: Rough up the surface to be painted
with fine grit sandpaper. Wipe with alcohol to ensure that
the surface is clean and dry. Use an appliance or industrial
grade, oil base, high gloss enamel paint.

KICKPLATE AIRFLOW

Model 315W uses a fan to take in room air through vents
in the left side of the kickplate, and discharges warm air
through vents in the right side. These vents must be kept
clear of obstructions or decorative panels. Blocking or
obstructing the kickplate will restrict airflow and cause
a decrease in performance and efficiency. Refer to the
illustration below.

Panel Specifications

odel 315W is offered in two design applications; stain-

M
less steel (/S) and overlay (/O). Each of these designs have
a full-view glass door.

The stainless steel model 315W/S is shipped from the
factory with the decorative stainless steel door panel and
matching handle in place.

The overlay model 315W/O is designed to accept a deco­rative door panel to match surrounding cabinetry. The
door panel and handle will be provided by the customer.
Refer to the chart for overlay panel specifications

For overlay panel handle hardware, we recommend a
D-style handle, centered top to bottom along the edge
opposite the hinge. You may have to countersink screw
heads to ensure hardware does not interfere with panels
fitting flush with unit doors.

Additional panel information can be found in the wine
storage section of the Sub-Zero design guide, or check
our website at subzero.com.

A solid panel cannot be installed over the glass door,
as this may cause moisture to form behind the panel.

IMPORTANT NOTE: The minimum air temperature the

wine storage unit will operate in is 50˚F
maximum is 100˚F

(38˚C).

(10˚C), and the

Install kickplate. Kickplate airflow.

Panel Specifications

OVER LAY PANEL WH

Panel Dimensions 15" (381) 301/16" (764)

Width of Rails and Stiles 21/4" (57) min

Panel Thickness

5

/8" (16) min

Panel Weight 10 lbs (5 kg) max

Model 315W Installation 9

GASKET

GLASS

13

/32" (11)

DIAMETER

1

/4" (6)

DIAMETER

OVERLAY

PANEL

DOOR

FRAME

TENON CENTER

subzero.com/specs

Overlay Panel Installation

nspect the overlay door panel for minimum thickness,

I
weight limit and finished inside edges. Decide if the handle
will be attached through the glass door frame or just
through the decorative door panel. If it is just through the
door panel, the handle must be attached first.

The overlay panel is attached using #8 x

5

/8" square drive
screws passing through the door frame from the rear,
behind the gasket into the panel. The panel is marked for
screw locations by the use of tenon centers, which are
temporarily inserted into the

1

/4" (6) diameter holes in the

front of the door frame. Refer to the illustration below.

With the unit secured in place and the door closed, hold
the panel in the desired position on the door and rap by
hand from the front, putting center marks on the rear
surface of the panel. If the door panel is made of such a
material that pre-drilling is needed, all of the mounting
holes should be marked. If not, only enough holes to hold
the panel in place temporarily, are necessary.

emove the door panel from the door frame and remove

R
tenon centers. Open the door. Using the center marks to
locate screws, drive the screws into the panel through the
black tape on the door frame.

The screw holes inside the door are hidden under a cover
flap on the door gasket. It is necessary to lift the flap to
insert the screws. Use as many screws as necessary to
hold the door panel in place securely.

IMPORTANT NOTE: After the first three or four mounting

screws are in place, but not completely tightened, close
the door and check the panel fit. This is the time to make
small adjustments. Once you are satisfied with the appear­ance, open the door and add the rest of the screws.
Check all screws for tightness.

The metal frame on the door has numerous mounting
holes on each side of the door. This is to accommodate
Sub-Zero accessory handles and provide for easy attach­ment of the handle through the door frame.

If you choose not to use the pre-drilled handle mounting
holes, it will be necessary to fasten the handle from the
rear of the door panel only, or drill one or more additional
holes through the metal frame of the door.

Tenon centers. Door frame cross section.

The cross-section illustration shows how the hole passes
through the door frame. The hole center is on the small
locator groove in the front of the frame. A
hole is made in the front wall of the extrusion and a

(11) diameter hole through the rest of the frame.

1

/4" (6) diameter

13

/32"

Exercise caution when drilling holes for mounting the
panel to the door frame.

Model 315W Installation 10

Overlay Panel Installation

The model 315W glass door is made with a sealed,
double-wall tempered glass core. The drill must not
contact this core when drilling. Be sure the hole is
centered on the small groove in the front of the door
frame and the drill passes squarely through the frame.
If you are inexperienced with drilling, fasten the handle
from the rear of the door panel only.

IMPORTANT NOTE:

holes in the door frame. The nature of the door panel with
a narrow outer rim and no connecting center member
requires the support provided by the glass door.

After the door panel installation is complete, apply the
cover patches or plugs provided over the holes on the
inside surface of the door.

The cover patches or plugs are part of the insulation
system on the door of the wine storage unit. Be sure to
cover all the holes in the door that were used.

Install screws in all the mounting

Installation Checklist

o ensure a safe and proper installation, the following

T
checklist should be completed by the installer to ensure
that no part of the installation has been overlooked.

Has all packing material been removed?

Turn the unit on. Is it operating properly? If not, is the
unit plugged in? Is the control turned on?

Has the unit been secured in place with the anti-tip
bracket?

Is the unit level? Are all leveling legs making contact
with the floor?

Is the power cord plugged into a properly grounded
3-prong outlet, which has been installed in accordance
with all applicable electrical codes?

Is the kickplate installed properly?

Is the door panel attached securely and properly
aligned?

Is the door aligned for proper appearance and
operation?

Have any installation or service problems been noted
on the product registration card? Has the registration
card been mailed in?

Has the stainless steel door been inspected for any
imperfections? This is to be done by the dealer or
installer with the customer upon completion of the
installation. Stainless steel panels are covered by a
limited 60-day parts and labor warranty for cosmetic
defects.

Service Information 11

subzero.com/specs

Service Information

f service is necessary, maintain the quality built into your

I
wine storage unit by calling Sub-Zero factory certified
service.

For the name and number of Sub-Zero factory certified
service nearest you, check the contact & support section
of our website, subzero.com or call Sub-Zero customer
care at 800-222-7820.

When calling for service, you will need the model and
serial numbers of your unit. Both numbers are listed on the
product rating plate, located on the underside of the top
wall. Refer to the illustration below.

If you are storing or disposing of your old refrigerator
or freezer, please do it
safely. Remove the
doors or tightly secure
the doors closed.
Child entrapment
accidents can be tragic.

RATING PLATE

Location of rating plate.

The information and images in this guide are the copyright property of Sub-Zero, Inc. Neither this guide nor any information or images contained herein may be
copied or used in whole or in part without the express written permission of Sub-Zero, Inc. © Sub-Zero, Inc. all rights reserved.

Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc.
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care and The Living Kitchen are registered trademarks and service marks of Sub-Zero, Inc.
(collectively,the“Company Marks.”) All other trademarks or registered trademarks arepropertyof theirrespectiveownersin the United States andothercountries.

SU B-ZER O, IN C. P. O. BOX 44 848 MA DISON , WI 5 3744 SUBZ ERO.C OM 800.222.7820

701 2206 RE V-A 9/20 11