Sub-zero 315I DATASHEET
Sub-Zero Undercounter units simplify
life at home by bringing refrigeration
anywhere it’s needed. In the kitchen,
a high-volume ice maker is a must
for entertaining. The Model 315I(P) ice
maker produces ice that resembles
a small barrel. Model 315I(P) has a
storage capacity of 26 pounds of ice.
Model 315I(P)
Undercounter Ice Maker
Interior Features
Ice Maker
Automatic Ice Maker
Automatic Defrost
Ice Scoop
Accessories
Classic stainless steel door front panel
with tubular handle in 15" and 18" widths
Classic stainless steel handle for custom
panel application
Filler strip for 18" opening
Accessories are available through your Sub-Zero
dealer. To obtain local dealer information, visit the
Locator section of our website, subzero.com.
Features
Can be fitted with a custom overlay or
stainless steel door front panel
Classic stainless steel door panel
with tubular handle available as sales
accessory
Model 315I has a gravity drain, while
Model 315IP has a built-in pump to allow
water to drain into adjacent sink
Automatic ice maker provides high-quality,
clear ice
Ice storage capacity of up to 26 lbs
Automatic defrost
Reversible door swing
Front venting with removable kickplate
allows unit to be serviced from the front
Meets strict Department of Energy
requirements
Model Options 315I 315IP
Drain Type Gravity Drain Drain Pump
Model 315I(P) shown with custom overlay door panel.
Classic
Installation Notes
The ice maker can be ordered with (Model
315IP) or without (Model 315I) a drain pump.
Each model has specific plumbing requirements. If you order the unit without a pump, a
drain must be installed.
Complete installation specifications, including
panel sizes, can be found on our website,
subzero.com.
Unit dimensions may vary by ±1/8".
Specifications
Overall Width 153/16"
Overall Height 335/8"
Overall Depth 24"
Door Clearance 151/4"
Ice Storage Capacity 26 lbs
Opening Width 151/4"
Opening Height 341/2"
Opening Depth 24"
Minimum Height Required 333/4"
Electrical Requirements 115 V AC, 60 Hz
15 amp dedicated circuit
Plumbing Requirements*
1
/4" copper line
20–100 psi
Shipping Weight 100 lbs
*Additional plumbing requirements are necessary
for the gravity drain (Model 315I) and the drain
pump (Model 315IP).
Installation Specifications
Overall Dimensions
Model 315I(P)
Undercounter Ice Maker
335/8"
(854)
153/16"
(386)
293/8"
(746)
4"(102)
335/8"
(854)
19"
(483)
21/8"(54)
SIDE VIEW FRONT VIEW
19"
(483)
TOP VIEW
153/16"
(386)
115˚
DOOR SWING
FRONT VIEW
SHUT-OFF
VALVE
WATER
FILTER
WATER
INLET TUBE
AIR GAP
DEVICE
DRAIN
TUBE
TOP VIEW
SHUT-OFF
VALVE
WATER
FILTER
WATER
INLET TUBE
DRAIN
TUBE
AIR GAP
DEVICE
24"
(609)
1
/8"(3)
151/4"
(387) MIN.
151/4"
(387) MIN.
341/2"
(876) NOMINAL
333/4"
(857) MIN.
Model 315I – Gravity Drain Model 315IP – Drain Pump
Dimensions in parentheses are in
millimeters unless otherwise specified.
1
/8"(3)
WATER
INLET
TUBE
DRAIN
24"
(610)
TUBE
LOCATE DRAIN
WITHIN 2" DIA.
AREA 23" BACK
FROM FRONT
OF UNIT
151/4"
(387) MIN.
TOP VIEW
341/2"
(876) NOMINAL
333/4"
(857) MIN.
WATER
INLET TUBE
DRAIN
TUBE
151/4"
(387) MIN.
FRONT VIEW
WATER
FILTER
WATER
FILTER
SHUT-OFF
VALVE
SHUT-OFF
VALVE
Loading...