Subaru LEGACY H7110LS200 User Manual
1
INSTALLATION
INSTRUCTIONS
SECURITY SYSTEM
UPGRADE
LEGACY
P/N: H7110LS200
Kit Contents:
1 Security Control Module w/Integral Bracket
1 Starter Interrupt/Horn Relays w/Integral Bracket
1 Horn w/Integral Bracket
1 Security Radio Mounting Bracket
2 Pan Head Screws (M5×8mm)
2 M6 Nuts
2 Window Decals
1 Installation Manual
Tools Required:
#1 Flat-tip Screwdriver
#2 Phillips Head Screwdriver
Electrical Tape
1/4” Drive Ratchet
10-inch 1/4” Drive Extension
10mm Socket
This device complies with FCC rules part 15. Operation is
subject to the following two conditions: (1) this device may
not cause harmful interference and (2) this device must
accept any interference that may cause undesired operation.
NOTE: This system requires prior installation of Keyless Entry
System. If installing both systems at the same time, install the
Keyless Entry System first.
00.08
UT28L-11
Printed in Japan
39412/SUBARU (P.01-09) 8/1/00 5:39 PM Page 1
2
Figure 1
Figure 2
Figure 3
A. Pre-Installation Notes
B. Security Module Installation
1. Vehicle Preparation
a. Lower the driver’s side window to avoid inadvertently locking the keys in the vehicle dur-
ing installation.
b. Disconnect negative battery terminal to prevent accidental shorting of any power circuits.
2. System Preparation
Remove the security module from the package and inspect for any physical damage.
3. Shock Sensor Adjustment
The shock sensor adjustment knob is recessed inside the unit and is covered by a protective
seal.
This adjustment is PRESET at the factory.
1. Remove the gearshift cover by pulling up in areas
indicated by arrows in Figure 1.
a. For automatic transmission, shifter must tem-
porarily be placed into neutral.
b. For standard transmission, the shift knob must
be removed by unscrewing.
2. Remove the tray by removing the two screws indicated by arrows in Figure 2.
3. Remove the ashtray. Disassemble ashtray assembly
by removing the two screws indicated by arrows in
Figure 3.
39412/SUBARU (P.01-09) 8/1/00 5:39 PM Page 2
3
Figure 4
Figure 5
Figure 6
4. Lift the center console cover by carefully pulling
outward in areas indicated by arrows in Figure 4.
5. Remove the six screws indicated by the arrows in
Figure 5. Do not disconnect any connectors. Pull the
unit out just far enough to access the passenger side
of the unit. See Figure 6.
NOTE: While the HVAC unit is pulled foward,
the ASPIRATOR SENSOR hose (located
on the driver’s side of the HVAC unit)
may disconnect. The hose must be reconnected during re-installation.
6. Install the security radio mounting bracket per
Figure 6, by first removing all radio, CD, etc. mounting screws visible on passenger side of car radio
bracket. Locate and install security radio mounting
bracket utilizing these screws.
7. Locate the security module 18-pin (white housing)
wire harness connector which is located behind or to
the right side of the audio unit.
8. Re-install the radio assembly. Insure all connectors
and ground wires are fully seated and secure.
Insure that the HVAC unit is functioning properly.
9. Insert the security module 18-pin connector into the
security module.
10. Mount the security module onto the support bracket
with two screws (M5
×8mm). See Figure 7.
NOTE: The security module must be firmly and
securely fastened to the support bracket.
If the security module is not properly
installed, the system’s shock sensor will
not function as intended.
Figure 7
39412/SUBARU (P.01-09)5ÇÃÉRÉsÅ[ 8/28/00 11:42 AM Page 3
Loading...