Strong 5 IN 1 User Manual
GB
STRONG UNIVERSAL REMOTE CONTROL “5 in 1”
Thank you for purchasing the STRONG “5 in 1” Universal Remote Control.
The remote can operate up to 5 dierent devices: TV, VCR, DVD player and
2 satellite receivers or cable TV boxes. The remote is powered by 2 “AAA”
type 1.5 Volt batteries – not included in this packaging.
Easy set-up
1. Insert 2 new batteries into the back of the remote. Following the
markings in the battery compartment.
2. Switch “ON” the device you wish to operate (e.g. your TV).
3. Look for the brand name of the device you wish to control in the
attached CODE LIST at the end of this user-manual (e.g. TV: SONY).
4. Next to the brand name you will nd one or more 3-digit code numbers
(e.g. SONY: 028) which have to be entered in the following way:
5. Press and hold both the key and the appropriate device key , ,
, , on the remote until the LED turns ON and then release both
keys. Then enter the 3-digit code numbers by using the numeric keys.
The key-in time is 10 seconds (see point 4). (e.g. + + 028).
Use following device keys:
for your TELEVISION,
for your VIDEO RECORDER,
for your DVD-PLAYER,
for your SATELLITE RECEIVER – default setting for
STRONG SRT 6125, 6155, 6355
for your second device: SATELLITE RECEIVER / CABLE BOX.
If the code number you inserted is correct (present in the database) then
the LED light will turn OFF immediately. If this number does not exist then
the LED is still ON. The key-in time is 10 seconds, if any key is not pressed
within 10 seconds then the LED will turn OFF and the same procedure must
be followed again (points 4-5).
6. Aim your remote control at the selected device and press the
Power key. Your remote control is set up correctly if the device switches
OFF and ON. Then check if keys e.g. VOLUME -/+ or e.g. at VCR/DVDPlayer: key can be operated.
7. If your device does not react and/or operates incorrectly, repeat step 3
to step 6 by entering the next 3-digit-code from the list.
8. If the brand of your device is not shown in the code number list, or if
none of the digit codes operates your device properly, you can try the
“automatic search function” :
Automatic search function
1. Switch ON the selected device you would like to control: TV, VCR,
DVD-Player, STB 1 or STB2.
2. Press and hold both the key and the appropriate device key until
LED light is ON and then release both keys.
www.strongsat.com
1
Use following device keys:
for your TELEVISION,
for your VIDEO RECORDER,
for your DVD-PLAYER,
for your SATELLITE RECEIVER – default setting for
STRONG SRT 6125, 6155, 6355
for your second device: SATELLITE RECEIVER / CABLE BOX
3. Press the key again, and then the LED should start blinking which
means your remote is in code search mode.
4. Press the key on remote and check if your device (e.g. TV) switches
OFF. Continue pressing this button slowly with intervals of about 2
seconds between each press until the device is switched OFF.
5. If it switches OFF, press the appropriate device key (e.g. ). LED light will
turn OFF now. Your device code for the selected device is now stored.
6. Aim the remote control at the selected device and press the key.
Your remote control is set up correctly if the device switches ON;
e.g. VOLUME -/+ or e.g. at VCR/DVD-Player: key can be operated.
7. If the selected devices operated incorrectly, repeat step 2 to step 6.
Note: If a key is not pressed within 30 seconds in the search mode, the
remote will stop the search.
Identifying CODE numbers – from the automatic search:
1. Press the key on the remote control. Now press both & key
and release.
Note: If the LED does not blink at all, the corresponding code for the rst
digit is 0.
2. Count the number of times the LED blinks and record this number.
3. Continue by pressing & and count the number of times the LED
blinks then record this number. For the second digit.
4. Continue by pressing & and count the number of times the
LED blinks then record this number for the third digit. You have now
identied the 3-digit code from the search.
Example: Key does not blink at all, it means the 1st digit of the code
number is [0], key blinking twice means 2nd digit is [2], key
blinking 8 times means 3rd digit is [8], therefore the code
number is 028.
If you think that the searching process is too slow, you can advance the
database searching process by pressing button.
Your Code Numbers
For future reference please record your CODE numbers in the elds for your
devices:
TV VCR DVD-Player STB 1 STB 2
2GBwww.strongsat.com
www.strongsat.com
GB
Basic functions:
1. STANDBY ON/OFF – Switches the device ON or OFF.
2. LED indicator – Blinks when remote control buttons are pressed.
3. TV – TV mode. Press this button to control your TV set.
4. SET – Used for programming other devices, such as VCR/DVD-Player etc.
5. VCR – VCR mode. Press this button to control your VCR.
6. STB2 –
7. DVD –
8. STB1 –
9. TV/RAD – Switches between TV or Radio mode in STB1 mode.
10. FAV – Displays the list of favourite channels in STB1 mode.
11. Mute – Enables or disables the sound Mutes in all modes
12. SUB –
13. CHANNEL Up/Down – Used for stepping through the channels or
14. VOL Left/Right – Used for adjusting the volume or for navigating
15. OK – In SAT1 mode: To conrm actions in the menu systems. In view
16. SAT – STB1 mode: Displays the list of satellites which have previously
17. TEXT – Enables / disables Teletext in STB1 and TV modes.
18. MENU – STB1 mode: The main menu for setting up the receiver.
19. Information – STB1 mode: Shows program information.
20. BACK –
21. AV – Selects TV or Digital TV
22. PAGE / Plus-Minus – STB1 mode: Scrolling page by page. Page+ for
23. EPG – Display the EPG (Electronic Program Guide).
24. PAUSE – STB1 mode: Freezes the picture. VCR/DVD-Player mode:
25. AUDIO – STB1 mode: Displays all available audio tracks on current
26. Blue – STB1 mode: The blue coloured button is used for various
27. Yellow – STB1 mode: The yellow colour is used for various functions in the
28. Red – STB1 mode: The red colour is used for various functions in the menus.
29. Green – STB1 mode: The green colour is used for various functions in
Buttons 26-29 – In Teletext mode: Functions according to Teletext content.
30. 0 - 9 Numeric – Direct entry of numerical functions in the menus or in
Second set top box mode. Press this button to controlyour second STB.
DVD-Playermode. Press this button to control your DVD-Player.
Default button for Strong SRT 6125/6155/6355 digital satellite receivers.
Display subtitles of broadcast in STB1 mode Used for stepping through
the channels or navigating within the OSD Menus in STB1 mode.
navigating within the OSD Menus in STB1 mode.
within the OSD Menus (left / right) in all modes.
mode: Displays the current channel list. (For example TV, Radio or
Favourite). In VCR/DVD-Player mode: Selects PLAY function.
installed channels.VCR/DVD-Player mode: STOP function.
VCR mode: RECORD function.
In STB1 and DVD-Player modes: Exits the current OSD (Menu) page. In
TV mode: switches back to previous channels
the next 10 items, Page- for the previous 10 items.
VCR/DVD-Player mode: FORWARD & BACKWARD functions.
PAUSE function.
service. It also displays all the available languages.
functions in the menus. TV mode: Brightness increase function
menu. TV mode: Brightness decrease function.
TV mode: Colour decrease function.
the menu. TV mode: Colour increase function.
channels selection
3
Specic functions of the remote control:
TV
All functions are marked directly on the keys.
Stepping through the channels
Displays current channel list
Enables/disables Teletext and use 4 colour buttons
Switches back to previous channel
RED - / GREEN +
YELLOW - / BLUE +
VCR
DVD
Colour function: increase/ decrease
Brightness function: increase/ decrease
PLAY function
STOP function
Record function
Forward function
Backward function
Pause function
PLAY function
STOP function
Forward function
Backward function
Pause function
GB
STB
3456
RED, GREEN,
YELLOW, BLUE
4
Displays the list of favourite channels
Displays subtitle of broadcast
Cursor for navigating within the OSD menu
Conrm actions in the menu system
Switches between TV or Radio mode
Setting up the receiver
Shows program information.
Exits the current OSD page
Selects TV or DIGITAL TV
Scrolling page by page. Page + for the next 10
items, Page - for the previous 10 items.
Used for various functions in the menu.
Freezes the picture
Displays all available audio languages/ tracks on
current service
www.strongsat.com
Loading...