STREAMLINE
®
Products for the Pure Water Cleaning Industry
INSTRUCTION MANUAL
PRODUCT
FILTERPLUS ®CLK
50, 75 & 100GPD Pumped RO Water Filtration
Systems.
PRODUCT CODE
50GPD-FP-CLK, 75GPD-FP-CLK,
100GPD-FP-CLK
WARRANTY
Covered for one year from
recorded date of purchase.
(See back page for further details)
Packed By_________ Checked By_________
Date ____/____/____
The
STREAMLINE
® water filtration system is designed to de-ionise
tap water and is simple to install and maintain.
It is the installer’s responsibility to ensure that this appliance is
plumbed in accordance with local authority’s bye-law regulations.
THIS KIT INCLUDES
1 x Filtration System
1 x Tap Valve
1 x Waste Saddle Clamp
5m x White Tube
(No faucet included)
SET UP INSTRUCTIONS
The system should be positioned near to a 15mm mains water
supply and a 40mm waste outlet. Fix the filtration system in the
desired location though the holes on the metal base plate (screws
not included). Position the holding tank in close proximity. Remove the wrapping from the pre-filter cartridges and click them
into place.
Remove wrapping from RO Membrane. Remove the RO feed tube
from the housing cap by undoing the nut. Unscrew the housing
cap and insert the RO membrane (See Fig 2) Replace the housing
cap, but leave the feed tube unscrewed to allow filter fines to be
flushed out once the system is plumbed in.
FIG. 2
RO MEMBRANE
HOUSING CAP
RO FEED
TUBE
WATER INLET
Connect an appropriate length of white tubing to the elbow
marked ‘Water Inlet’, allowing enough tubing to connect to the
mains water supply. The plastic fastening nut should be loosened, and the tube pushed in as far as possible, before tightening
the plastic nut securely .
MAINS & WASTE WATER CONNECTIONS
Turn the mains water supply o. Attach the tap valve to a standard 15mm copper, water supply. (See Fig 4)
Ensure that the tap valve is eectively sealed by using PTFE tape
on each joint. Connect a suitable length of tube from the tap
valve to the connection marked ‘water inlet’ on the filter system.
(See Fig 3)
FEED TO FAUCET
WASTE WATER
WATER INLET
FIG. 3
Connect an appropriate length of tubing to the fitting marked
‘Drain’ or ‘Waste Water Tube’ (See Fig 5), allowing enough tubing
to reach the nearest 40mm waste pipe.
Attach the black saddle clamp to a 40mm waste outlet pipe by
using the two bolts supplied.
Remove fastening nut mounted on the saddle clamp and drill a
6mm hole through the tube connection. Replace fastening nut and
connect the tube coming from the fitting marked ‘Waste Water
Tube’. (See Fig 5 & 7).
FIG. 4
TAP
WATER FEED
15mm WATER
SUPPLY
START UP
Ensure that all fittings are tightened securely. Turn the mains
water supply on and check for leaks. Allow a few minutes for the
system to allow trapped air to escape and for filter fines to be
flushed out before securing the feed tube on the RO housing.
Plug the booster pump into a mains power supply and switch it
on.
When fully pressurised, check all fittings again for leaks.
MAINTENANCE
Quarterly Replace the three prefilters every 3 months, or
sooner in very hard water areas (300TDS+).
Replace the RO Membrane when the TDS reading rises above an
acceptable figure (10ppm) or when pure water flow becomes
minimal.
STREAMLINE
® WARRANTY
The warranty on Machines and Equipment is for 1 year from RECORDED DATE
OF PURCHASE.
THIS WARRANTY EXCLUDES NORMAL MAINTENANCE ITEMS, including but
not limited to HOSES, FILTERS, O-RINGS, DIAPHRAGMS, VALVES, GASKETS,
CARBON BRUSHES and damage to motors and other components as a result
of failure to replace normal maintenance items. THIS LIST IS NOT
EXHAUSTIVE.
If VARITECH receives notice of such defects during the warranty period,
STREAMLINE
® will either, at its opinion, repair or replace components which
prove to be defective.
Replacement parts will only be supplied under warranty, upon the inspection
and approval of the defective parts by
STREAMLINE
®.
Should it be necessary to supply replacement parts before the opportunity to
inspect, these will be charged at current prices and credit will only be issued
upon subsequent inspection and warranty approval by
STREAMLINE
®.
The customer is responsible for the cost of return of the defective part. If
warranty is approved,
STREAMLINE
® will pay for the cost of the repaired or
replacement part.
REPLACEMENT PARTS SUPPLIED UNDER WARRANTY WILL BE
GUARANTEED FOR THE REMAINDER OF THE ORIGINAL PARTS WARRANTY
AND NOT FROM THE INSTALLATION DATE.
This warranty excludes the following conditions and circumstances which are
at the discretion of
STREAMLINE
®
:-
WEAR AND TEAR, MISUSE, ABUSE, IMPROPER MAINTENANCE, FROST
DAMAGE, THE USE OF CHEMICALS OTHER THAN THOSE SUPPLIED OR
APPROVED BY
STREAMLINE
®, IMPROPER INSTALLATION OR REPAIR,
UNAUTHORISED MODIFICATION, INCIDENTAL OR CONSEQUENTIAL COSTS,
LOSS OR DAMAGE, SERVICE, LABOUR OR THIRD PARTY CHARGES, THE
COST OF RETURNING DEFECTIVE PARTS TO
STREAMLINE
®.
This warranty constitutes the exclusive remedy of any purchaser of a
STREAMLINE
® unit and is in lieu of all other warranties, express or implied,
including without limitation any implied warranty of merchantability or fitness
for use, to the fullest extent permitted by law. In no event shall any implied
warranty of merchantability or fitness for use exceed the term of the
applicable warranty stated above and
STREAMLINE
® shall have no other
obligation or liability.
These rights cannot be transferred to a third party.
August 2015
Loading...