Stow CX22DUO, CX44DUO, CX44DUOE, CX22DUOE Operation And Parts Manual

Download

Page 1

OPERATION AND PARTS MANUAL

DUO HAND MIXERS

CX22DUO

CX22DUOE

CX44DUO

CX44DUOE

Revision #1 (06/15/07)

STOW CONSTRUCTION EQUIPMENT

A DIVISION OF STOW INC.

POST OFFICE BOX 6254

CARSON, CA 90749 310-537-3700 • 888-252-STOW [888-252-7869] FAX: 310-537-1986 • FAX: 800-556-1986 E-MAIL: STOW@STOW.com • WWW: stowmfg.com

PARTS DEPARTMENT:

800-427-1244 FAX: 800-672-7877

SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:

800-478-1244 FAX: 310-631-5032

Page 2

CX22/CX44 DUO HAND MIXER — SILICOSIS WARNING

WARNING

SILICOSIS WARNING RESPIRATORY HAZARDS

Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In addition, California and some other authorities have listed respirable crystalline silica as a substance known to cause cancer. When cutting such materials, always follow the respiratory precautions mentioned above.

WARNING

Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar with the risks associated with the particular process and/or material being cut or the composition of the tool being used, review the material safety data sheet and/or consult your employer, the material manufacturer/supplier, governmental agencies such as OSHA and NIOSH and other sources on hazardous materials. California and some other authorities, for instance, have published lists of substances known to cause cancer, reproductive toxicity, or other harmful effects.

Control dust, mist and fumes at the source where possible. In this regard use good work practices and follow the recommendations of the manufacturers or suppliers, OSHA/NIOSH, and occupational and trade associations. Water should be used for dust suppression when wet cutting is feasible. When the hazards from inhalation of dust, mists and fumes cannot be eliminated, the operator and any bystanders should always wear a respirator approved by NIOSH/MSHA for the materials being used.

Page 3

CX22/CX44 DUO HAND MIXER — TABLE OF CONTENTS

STOW CX22/CX44 DUO HAND MIXER

Silicosis Warning ....................................................... 2

Table Of Contents ..................................................... 3

Parts Ordering Procedures ....................................... 4

Safety Message Alert Symbols ................................. 5

Rules For Safe Operation ...................................... 6-7

Specifications ............................................................ 8

General Information .................................................. 9

Components............................................................ 10

Setup ....................................................................... 11

Operation ................................................................ 12

Maintenance ........................................................... 13

Explanation Of Code In Remarks Column .............. 14

Suggested Spare Parts ........................................... 15

Component Drawings

Mixer Assembly (CX22) ..................................... 16-19

Mixer Assembly (CX44) ..................................... 20-23

Terms and Conditions of Sale - Parts ..................... 24

NOTE

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 3

Specification and part number are subject to change without notice.

Page 4

CX22/CX44 DUO HAND MIXER — PARTS ORDERING PROCEDURES

When ordering parts,

please supply the following information:

❒❒

❒ Dealer account number

❒❒ ❒❒

❒ Dealer name and address

❒❒ ❒❒

❒ Shipping address (if different than billing address)

❒❒ ❒❒

❒ Return fax number

❒❒ ❒❒

❒ Applicable model number

❒❒ ❒❒

❒ Quantity, part number and description of each part

❒❒ ❒❒

❒ Specify preferred method of shipment:

❒❒

✓ FedEx or UPS Ground ✓ FedEx or UPS Second Day or Third Day ✓ FedEx or UPS Next Day ✓ Federal Express Priority One ✓ DHL ✓ Tr u ck

Here’s how to get help...

Please have the model and serial number on hand when calling.

Note: Unless otherwise indicated by customer, all orders are treated as “Standard Orders”, and will ship within 24 hours. We will make every effort to ship “Air Shipments” the same day that the order is received, if prior to 2PM west coast time. “Stock Orders” must be so noted on fax or web forms.

Place Your Parts Order Via Web or Fax

For Even More Savings!

Parts Department

800-427-1244 Fax: 800-672-7877

310-537-3700 Fax: 310-637-3284

Service Department

800-478-1244 Fax: 310-537-4259

310-537-3700

Technical Assistance

800-478-1244 Fax: 310-631-5032

Warranty Department

800-421-1244, Ext. 279 Fax: 310-537-1173

310-537-3700, Ext. 279

Sales Department

310-661-4242 Fax: 310-604-9237

877-289-7869 (877-BUY-STOW)

STOW CONSTRUCTION EQUIPMENTSTOW CONSTRUCTION EQUIPMENT

STOW CONSTRUCTION EQUIPMENT

STOW CONSTRUCTION EQUIPMENTSTOW CONSTRUCTION EQUIPMENT

A DIVISION OF STOW INC.

POST OFFICE BOX 6254

CARSON, CA 90749 310-537-3700 • 888-252-STOW [888-252-7869] FAX: 310-537-1986 • FAX: 800-556-1986 E-MAIL: stow@STOW.com • WWW: stowmfg.com

Extra Discounts!

All parts orders which include complete part numbers and are received by our automated web parts order system, or by fax qualify for the following extra discounts:

Ordered Standard Stock orders

via orders ($750 list and above)

Fax 3% 10%

Web 5% 10%

Special freight allowances when you order 10 or more line items via Web or Fax!**

FedEx Ground Service

No other allowances on freight shipped by any other carrier.

NOTE: DISCOUNTS ARE SUBJECT TO CHANGE

at no charge for freight

Direct TOLL-FREE access

to our Parts Department:

Toll-free nationwide — 800-427-1244

PAGE 4 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)

Page 5

CX22/CX44 DUO HAND MIXER — SAFETY MESSAGE ALERT SYMBOLS

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.

This Manual has been developed to provide complete instructions for the safe and efficient operation of

NOTE

the STOW

HAND MIXER.

Before using this mixer, ensure that the operating individual has read and understands all instructions in this manual.

Model CX22/CX44 D UO

HAZARD SYMBOLS

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you about potential hazards that could injure you or others. The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words: DANGER,

WARNING, or CAUTION.

Rotating Parts

NEVER operate equipment with covers or

guards removed. Keep fingers, hands, hair and clothing away from all moving parts to prevent injury.

Accidental Starting

ALWAYS place power ON/OFF switch in the OFF position when the mixer is not in use.

Sight and Hearing hazard

ALWAYS wear approved eye and hearing

protection.

DANGER

You WILL be

KILLED

SERIOUSLY

injured if you DO

NOT follow directions.

WARNING

You CAN be

KILLED

SERIOUSLY

injured if you DO

NOT follow directions.

CAUTION

You CAN be

Potential hazards associated with the STOW CX22/CX44 DUO HAND MIXER operation will be referenced with Hazard Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Message Alert Symbols.

INJURED

if you DO NOT follow directions.

Other important messages are provided throughout this manual to help prevent damage to your mixer, other property, or the surrounding environment.

NOTE

Respiratory Hazard

ALWAYS wear approved respiratory

protection.

Equipment Damage Messages

This mixer, other property, or the surrounding environment could be damaged if you do not follow instructions.

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 5

Page 6

CX22/CX44 DUO HAND MIXER — RULES FOR SAFE OPERATION

■

NEVER use accessories or attachments, which are not

DANGER

Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only.

The following safety guidelines should always be used when operating the

Multiquip CX22/CX44 Duo Hand Mixers.

GENERAL SAFETY

■

DO NOT operate or service this equipment before reading this entire manual.

■

This equipment should not be operated by persons under 18 years of age.

■

NEVER operate this equipment without proper protective clothing, shatterproof glasses, steel-toed boots and other protective devices required by the job.

recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.

■

Manufacturer does not assume responsibility for any accident due to equipment modifications.

■

ALWAYS read, understand, and follow procedures in Operator’s Manual before attempting to operate equipment.

■

ALWAYS be sure the operator is familiar with proper safety precautions and operations techniques before using mixer.

■

ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children.

■

NEVER leave the mixer unattended, turn off electric motor when unattended.

■

CAUTION must always be observed while servicing this mixer. Rotating parts can cause injury if contacted.

■

Unauthorized equipment modifications will void all warranties.

■

Ensure that any extension cable is protected against damage and not liable to be tripped over or trapped underneath the mixer.

■

NEVER operate this equipment when not feeling well due to fatigue, illness or taking medicine.

■

NEVER operate this equipment under the influence or drugs or alcohol.

■

Whenever necessary, replace nameplate, operation and safety decals when they become difficult read.

■

ALWAYS check the machine for loosened threads or bolts before starting.

■

ALWAYS wear proper respiratory (mask) hearing and eye protection equipment when operating the mixer.

■

DO NOT allow extension cord to come into contact with water or fluids.

■

DO NOT spray water onto electric motor.

■

Mixer must be used only for its intended purpose.

■

This mixer is not suitable for the mixing of

explosive

■

NEVER operate the mixer in an

■

Keep area around the mixer could cause persons to fall onto

■

ALWAYS ensure mixer is on level ground before mixing.

■

Become familiar with the controls of the mixer before

substances.

explosive

clear of obstructions

moving parts

flammable

atmosphere.

which

operating.

■

ALWAYS disconnect AC power plug from power source before moving mixer.

■

If mixer is equipped with an electric motor, operate electric motor only at the specified voltage indicated on the nameplate.

■

Make sure the

always

in the

OFF/ON

OFF

power switch on the electric motor is

position before inserting the mixer's power

plug into an AC receptacle (electric model only).

PAGE 6 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)

Page 7

CX22/CX44 DUO HAND MIXER — RULES FOR SAFE OPERATION

Maintenance Safety

■

NEVER lubricate components or attempt service on a running machine.

■

ALWAYS allow the machine a proper amount of time to cool

before servicing.

■

Keep the machinery in proper running condition.

■

Fix damage to the machine immediately and always replace broken parts, or missing decals.

■

Dispose of hazardous waste properly.

■

DO NOT use food or plastic containers to dispose of hazardous waste.

Emergencies

■

ALWAYS know the location of the nearest

and first aid kit.

fire extinguisher

■

In emergencies

nearest phone or Also know the phone numbers of the nearest

ambulance, doctor

information will be invaluable in the case of an emergency.

always

know the location of the

keep a phone on the job site

and

fire department

. This

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 7

Page 8

CX22/CX44 DUO HAND MIXER — SPECIFICATIONS

snoitacificepS44XC/22XC.1elbaT

ledoM

EOUD22XC/OUD22XCEOUD44XC/OUD44XC

egatloVV032/V021-011V032/V021-011

sttaW000,1/008004,1

PH4/1/1.12

spmA4.4/2.

70.6/7.21

sraeG22

1raeG-daoLrednUMPR004-0053-0

2raeG-daoLrednUMPR025-0005-0

retemaiDlooTgnixiMdednemmoceR)mc21(se

hcni57.4)mc41(sehcni5.5

retemaiDkceNeldnipS)mc5(sehcni2)mc5(sehcni2

leveLerusserPdnuoS)A(Bd48)A(Bd48

ssimEesioN)A(Bd79)A(Bd79

leveLnoi

noitarbiVmrA-dnaHtf2.8<

m67.0(

)tf2.8<

m67.0(

)

noitcetorPlacirtcelEdetalusnI-elbuoDdetalusnI-elbuoD

yticapaCgnixiM)sretil94-91(snollag31-5)sretil59-83(s

thgieW)gk7.7(bl71)gk5.9(bl12

nollag52-01

PAGE 8 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)

Page 9

CX22/CX44 DUO HAND MIXER — GENERAL INFORMATION

Application

The Stow CX22/CX44 Duo Hand Mixer is designed for mixing of chemical building products of all standard viscosities (liquid, pasty, viscous, powdery) used in the building industry and building-related trades.

The right mixing tool should be selected depending on the consistency of the material and the quantity to be mixed.

Ensure that the extension cable is carefully laid out avoid-

wet areas, sharp edges

ing might run over it.

Unroll the extension cable fully or it will overheat and could catch fire. Make sure that all extension cable connections are dry and safe. Replace any defective or worn-out extension cable immediately.

If used properly, the hand mixer will provide years of safe and reliable service.

The CX22/CX44 is not to be used for the processing or preparation of food or similar products. The machine is also not suitable for mixing materials containing graphite powder, hydrochloric solutions or liquid manure. Mixing such

erepmA gnitaR egnaR

materials can damage or destroy machine.

Paddles

The CX22DUO and CX22DUOE hand mixers come with MKD120HF paddles. The MKD120HF paddles have a diameter of 4 3/4 inches and are used to mix a volume of 5 to 13 gallons. The CX44DUO and CX44DUOE hand mixers come with MKD140HF paddles. The MKD140HF paddles have a diameter of 5 1/2 inches and are used to mix a volume of 10 to 25 gallons.

Electrical

Make sure that the power being supplied to the motor corresponds to the voltage rating label on the motor. Supplying the wrong voltage to the electric motor will cause severe electrical damage to the motor.

Always make sure the is in the

OFF

position before applying power.

OFF/ON

switch on the electric motor

and locations where vehicles

seziSdroCnoisnetxE.2ELBAT

stloV teeFnidroCfohtgneL

V511 .tF52 .tF05 .tF001 .tF051 .tF002 .tF052

V032 .tF05 .tF001 .tF002 .tF003 .tF004 .tF005

2-0 81 81 81 61 61 41

3-2 81 81 61 41 41 21

4-3 81 81 61 41 21 21

5-4 81 81 41 21 21 01

6-5 81 61 41 21 01 01

8-6 81 61 21 01 01 8

01-8 81 41 21 01 8 8

21-01 61 41 01 8 8 6

41-21 61 21 01 8 6 6

61-41 61 21 01 8 6 6

81-61 41 21 8 8 6 4

02-81 41 21 8 6 6 4

Extension Cables

The extension cable should be a 3-wire configuration that includes a ground wire that conforms to UL code. Choose the correct size of an extension cord as shown in Table 2. Remember

distance

affects the wire size of the extension

cable.

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 9

Page 10

CX22/CX44 DUO HAND MIXER — COMPONENTS

Figure 1. Mixer Major Components

Refer to Figure 1 for the location of the following mixer components.

1. Ventilation Slits — These openings allow ventilation to the unit to prevent overheating.

2. Safety Lock-off Button — When on, prevents the unit from being operated accidentally.

3. Protection Frame — Protects the machine casing from dirt and breakage.

4. ON/OFF Switch with Speed Control — Turns the power on and off and regulates the mxing speed.

PAGE 10 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)

5. Gear Selection Lever — This lever is used to select the gear (slow or fast) at which the unit is operating.

6. Protection Frame Fastening Screws — Holds the protection frame securely in place.

7. Machine Neck — The mixing tools are attached to the machine neck.

8. HEXAFIX

Quick Action Coupling — These connectors

attach the mixing tools to the machine neck.

9. Mixing Tools — These tools are used to mix chemical building products.

Page 11

CX22/CX44 DUO HAND MIXER — SETUP

Assembly

Electric Connections

Before using the hand mixer, the following steps need to be performed.

DO NOT attempt to operate the mixer until the Safety, General

1. Insert the mixing tools into the HEXAFIX coupling as far as necessary to lock the tools in place, automatically

Information and Set-Up sections have been read and understood.

(see Figure 2).

PULL BACK

Before plugging the power cable, check and make sure that the ON/OFF switch operates properly and returns to the OFF position when released.

INSERT

1. Connect the hand mixer power cable to a 110 V or 230V, 50/60 Hz power source, depending on the unit you have. Make sure you conform to the specifications on the nameplate of the mixer.

2. A 120V/230V power supply can also be used. Make

Figure 2. Inserting Mixing Tools

sure that the power supply conforms to the specifications on the nameplate of the mixer. Voltage

2. When installing the mixing tools, make sure that the blades are correctly positioned as shown in Figure 3.

decrease of more than 10% will cause loss of power and overheating.

CAUTION

Correct position of the blades

Figure 3. Positioning Blades

3. When inserting mixing tools, also make sure that the identifying marks on both the mixing shaft and the mixing blades match as shown in Figure 4.

IDENTIFYING MARKS SHOULD MATCH

3. Use an extension cord (see Table 2) of adequate current carrying capacity.

NEVER

use a

worn

frayed

extension cord. Insert the electric motor's power plug into one end of the extension cord.

DANGER

NEVER

while

touch the power cord (Figure 5) with

standing in water

when it is connected to a power

wet hands

source. The possibly exists of electrical shock (electrocution) even death.

NEVER

spray water directly on the electric motor.

Figure 5. Extension Cord (Wet Hands)

IDENTIFYING MARKS SHOULD MATCH

Figure 4. Matching Identifying Marks

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 11

NOTE

To prevent personnel from tripping over the extension cord, position the extension cord so that it lays flat and is

not curled.

Page 12

CX22/CX44 DUO HAND MIXER — OPERATION

CAUTION

ALWAYS hold the machine with both hands while working.

4. When submerging the mixing tool in the mixing material or when lifting out the mixing tool, always reduce the speed. When the mixing tool is fully submerged, increase the speed again to ensure that the motor is adequately cooled.

1. To start , press the starting lockout button then press the ON/OFF switch (Figure 6). The integrated electronic controls will start the machine in a controlled speed.

STARTING LOCKOUT BUTTON

ON/OFF SWITCH

Figure 6. ON/OFF Switch

2. To make the motor run faster, apply more pressure to the ON/OFF switch.

3. To change the maximum speed, turn the gear selection lever 180° (Figure 7). First gear is slow and second gear is fast.

5. During mixing, guide the mixer around the mixing container (Figure 8). Continue mixing until all of the material is completely mixed.

GUIDE MIXER

Figure 8. Mixing the Material

6. To stop the mixer, release the On/OFF switch.

7. Always clean the mixing tool after every use.

FAST

Figure 7. Gear Selection Lever

PAGE 12 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)

SLOW

Page 13

CX22/CX44 DUO HAND MIXER — MAINTENANCE

CAUTION

ALWAYS disconnect the mixer from the power supply

before cleaning, changing the mixing paddles or performing any maintenance.

CAUTION

Mixer Storage

For storage of the mixer for over 30 days, the following is recommended:

Clean the mixer and mixing tools.

Cover the mixer and place it a clean dry area, that is protected from harsh elements.

To assure product safety and reliability, repairs, maintenance, and adjustments should be performed by an authorized service center or qualified technician to prevent any misplaced wires and components that could cause serious hazards.

1. Clean the machine and mixing tools after every use.

2. Keep the quick-action coupling clean and free of dust. Apply grease to the hexagon mount regularly.

3. Keep the ventilation slits clean and free of foreign matter so that machine can be properly cooled.

4. Replace the carbon brushes when worn. The machine is equipped with self-deactivating carbon brushes. The machine will shut itself down when a certain level of wear is reached, indicating that carbon brushes should be replaced.

5. Clean and lubricate gear care yearly or whenever servicing requires that the gear case to be removed.

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 13

Page 14

EXPLANATION OF CODE IN REMARKS COLUMN

The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions.

The contents and part numbers listed in the parts section are subject to change guarantee the availibility of the parts listed.

Sample Parts List:

NO. PART NO. PART NAME QTY. REMARKS

1 12345 BOLT ....................... 1 .... INCLUDES ITEMS W/

2*12347 WASHER, 3/8 IN. .... 1 ....

3 12348 HOSE .................... A/R .. MAKE LOCALLY

4 12349 BEARING ................ 1 .... S/N 2345B AND ABOVE

NO. Column

Unique Symbols - All items with same unique symbol

, #, +, %, or >) in the number column belong to the same

(

assembly or kit, which is indicated by a note in the “Remarks” column.

Duplicate Item Numbers - Duplicate numbers indicate multiple part numbers are in effect for the same general item, such as different size saw blade guards in use or a part that has been updated on newer versions of the same machine.

NOTE

without notice

WASHER, 1/4 IN. ...........

When ordering a part that has more than one item number listed, check the remarks column for help in determining the proper part to order.

. Multiquip does not

NOT SOLD SEPARATELY MQ-45T ONLY

QTY. Column

Numbers Used - Item quantity can be indicated by a number,

a blank entry, or A/R. A/R (As Required) is generally used for hoses or other parts

that are sold in bulk and cut to length. A blank entry generally indicates that the item is not sold

separately. Other entries will be clarified in the “Remarks” Column.

REMARKS Column

Some of the most common notes found in the “Remarks”

Column are listed below. Other additional notes needed to describe the item can also be shown.

Assembly/Kit

symbol will be included when this item is purchased. Indicated by:

“INCLUDES ITEMS W/(unique symbol)”

Serial Number Break

range where a particular part is used. Indicated by:

“S/N XXXXX AND BELOW” “S/N XXXX AND ABOVE” “S/N XXXX TO S/N XXX”

Specific Model Number Use

only with the specific model number or model number variant listed. It can also be used to show a part is NOT used on a specific model or model number variant.

Indicated by:

“XXXXX ONLY” “NOT USED ON XXXX”

- All items on the parts list with the same unique

- Used to list an effective serial number

- Indicates that the part is used

PART NO. Column

Numbers Used - Part numbers can be indicated by a number,

a blank entry, or TBD. TBD (To Be Determined) is generally used to show a part that

has not been assigned a formal part number at time of publication.

A blank entry generally indicates that the item is not sold separately or is not sold by Multiquip. Other entries will be clarified in the “Remarks” Column.

PAGE 14 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)

“Make/Obtain Locally”

purchased at any hardware shop or made out of available items. Examples include battery cables, shims, and certain washers and nuts.

“Not Sold Separately”

purchased as a separate item and is either part of an assembly/kit that can be purchased, or is not available for sale through Multiquip.

- Indicates that the part can be

- Indicates that an item cannot be

Page 15

CX22/CX44 DUO HAND MIXER — SUGGESTED SPARE PARTS

CX22/CX44 DUO HAND MIXER 1 TO 4 UNITS

Qty. P/N Description

2 ....... CM20509 ........... SPRING FOR BRUSH ASSY (CX22)

1 ....... CM20567 ........... BRUSH SET (CX22)

2 ....... CM20569 ........... BRUSH HOLDER (CX44)

1 ....... CM20566 ........... BRUSH SET (CX44)

Part numbers on this Suggested

NOTE

Spare Parts List may supercede/ replace the P/N's shown in the test pages of this manual.

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 15

Page 16

CX22 DUO HAND MIXER — MIXER ASSEMBLY

BODY ASSY.

121

113

111

109

112

116

117

116

119

120

114

118

116

117

116

119

120

115

PAGE 16 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)

110

Page 17

CX22 DUO HAND MIXER — MIXER ASSEMBLY

BODY ASSY.

NO PART NO PART NAME QTY. REMARKS

1 CM20530 MOTOR HOUSING TOP 1 2 CM20531 MOTOR HOUSING BOTTOM 1 3 CM20654 GEAR HOUSING ASSY 1 4 CM20655 PLATE ASSY 1 5 CM20524 BAFFLE PLATE 1 6 CM20525 RECTIFIER 1 7 CM20656 SPINDLE, RIGHT 1 8 CM20522 COVER 1

9 CM20559 ARMATURE 230V .............................................. 1 ......... CX22DUOE ONLY

9 CM20591 ARMATURE 110V ............................................... 1 ......... CX22DUO ONLY

10 CM20556 FIELD COIL 110 - 230V 1 11 CM20657 SPINDLE, LEFT 1 12 CM20658 MIDDLE SHAFT 1 13 CM20518 WASHER 3 14 CM20504 MIDDLE SHAFT 1 15 CM20546 GEAR ASSY 1 16 CM20501 GEAR 2 17 CM20506 SLEEVE 2 18 CM28543 GUIDE 1 19 CM20659 FORK 1 20 CM20660 SLIDING PLUG 1 21 CM20508 SPRING FOR GEAR SHIFTER 2 22 CM20513 WASHER 2 23 CM20540 FRAME PROTECTION RIGHT 1 24 CM20541 FRAME PROTECTION LEFT 1 25 CM20528 GEAR KNOB 1 26 CM20562 KNOB ASSY 1 27 CM20581 SEALING 1 29 CM25022 SLEEVE 1 30 CM29523 RUBBER SLEEVE 1 31 CM29522 BALL BEARING 607 2Z 1 32 CM25055 BALL BEARING 6000 2RS 1 35 CM23507 BALL BEARING 6002 2RS 2 36 CM23016 BALL BEARING 6204 2RS 2 37 CM20509 SPRING FOR BRUSH ASSY 2 38 CM20661 COVER 1 39 CM20609 SCREW 4X12 2

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 17

Page 18

CX22 DUO HAND MIXER — MIXER ASSEMBLY

BODY ASSY.

121

113

111

109

112

116

117

116

119

120

118

114

118

116

117

116

119

120

115

PAGE 18 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)

110

Page 19

CX22 DUO HAND MIXER — MIXER ASSEMBLY

BODY ASSY.

NO PART NO PART NAME QTY. REMARKS

41 42 CM20571 CIRCLIP 20 2 43 CM20572 CIRCLIP 47 2 46 CM28548 PIN 5X5X10 2

50 CM20565 SWITCH ASSY 230V .......................................... 1 .......... CX22DUOE ONLY

50 CM20593 SWITCH ASSY 110V .......................................... 1 .......... CX22DUO ONLY

55 CM29534 CAPACITOR

57 CM23557 CORD, ELECTRIC, 230 V WITH EU PLUG ......... 1 .......... CX22DUOE ONLY

57 CM27030 CORD, ELECTRIC, 230 V WITH CH PLUG ........ 1 .......... CX22DUOE ONLY

57 CM27053 CORD, ELECTRIC, 230 V WITH UK PLUG ........ 1 .......... CX22DUOE ONLY

57 CM27035 CORD, ELECTRIC, 110 V WITH UK PLUG ......... 1 .......... CX22DUO ONLY

57 CM27054 CORD, ELECTRIC, 110 V WITH USA PLUG ...... 1 .......... CX22DUO ONLY

58 CM20588 CABLE SWITCH 1 59 CM23556 CORD GUARD 1 60 CM20584 WIRE RED 1 61 CM20583 WIRE BLUE 1 62 CM20584 WIRE RED 1 64 CM20579 TERMINAL BLOCK 1 68 CM20567 BRUSH SET 1 70 CM25062 SCREW 4 X 15 14 71 CM20636 SCREW 4X55/20 2 72 CM20574 SCREW 4X70/30 4 73 CM20575 SCREW M6X20 8 74 CM20577 SCREW 30X12 2 76 CM20576 NUT M6 8 78 CM20578 BALL 5 MM 1 79 CM20507 SPRING FOR GEAR SWITCH 1 80 CM23555 CORD CLAMP 1 82 CM27011 WASHER 2 85 CM20662 SEALING 1 109 CM29544 BALL BEARING 608 2RS 1 110 CM20663 SHAFT 1 111 CM28568 CIRCLIP 22 2 112 CM20664 GEAR 1 113 CM28569 CIRCLIP 8 1

114 CM20665 HEXAFIX® LEFT - I ............................................. 1 .......... INCLUDES ITEMS W/ #

115 CM20666 HEXAFIX® RIGHT - II ......................................... 1 .......... INCLUDES ITEMS W/ $

116#$ CM20667 RING FOR HEXAFIX 117#$ CM20668 SPRING FOR HEXAFIX 118#$ CM20669 PIN FOR HEXAFIX 119#$ CM20670 SLEEVE FOR HEXAFIX 120#$ CM20571 CIRCLIP 20 2 121 DCL1260 DECAL; STOW LOGO 1

CM24060 CIRCLIP A15 X1.5 2

4 2 4 2

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 19

Page 20

CX44 DUO HAND MIXER — MIXER ASSEMBLY

BODY ASSY.

107

176

175

174

105

123

121

122

126

127

126

129

130

128

114

128

126

127

126

129

130

125

PAGE 20 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)

103

120

101

Page 21

CX44 DUO HAND MIXER — MIXER ASSEMBLY

BODY ASSY.

NO PART NO PART NAME QTY. REMARKS

1 CM20532 MOTOR HOUSING TOP 1 2 CM20533 MOTOR HOUSING BOTTOM 1 3 CM20654 GEAR HOUSING ASSY 1 4 CM20671 PLATE ASSY 1 5 CM20646 RIGHT AND LEFT HANDLE ASSY 1 10 CM20523 COVER 1 14 CM20656 SPINDLE RIGHT 1 15 CM20535 BAFFLE PLATE 1 16 CM20525 RECTIFIER 1

19 CM20672 ARMATURE 230V ................................................ 1 ......... CX44DUOE ONLY

19 CM20673 ARMATURE 110V ................................................ 1 ......... CX44DUO ONLY

20 CM20555 FIELD COIL 110 - 230V 1 22 CM20516 CARRIER 2 25 CM20657 SPINDLE LEFT 1 26 CM20550 MIDDLE SHAFT 1 27 CM20504 MIDDLE SHAFT 1 28 CM20545 GEAR ASSY 1 29 CM20501 GEAR 2 30 CM20518 WASHER 3 31 CM20506 SLEEVE 2 34 CM28543 GUIDE 1 35 CM20659 FORK 1 36 CM20660 SLIDING PLUG 1 37 CM20508 SPRING FOR GEAR SHIFTER 1 38 CM20661 COVER 1 39 CM20609 SCREW 4X12 1 40 CM20513 WASHER 2 41 CM20542 FRAME PROTECTION RIGHT 1 42 CM20543 FRAME PROTECTION LEFT 1 44 CM20528 GEAR KNOB 1 45 CM20562 KNOB ASSY 1 46 CM20581 SEALING 1 48 CM25022 SLEEVE 1 50 CM25053 RUBBER SLEEVE 1 51 CM29544 BALL BEARING 608 2RS 2 52 CM24523 BALL BEARING 6001 ZZ 1 55 CM23507 BALL BEARING 6002 2RS 2 56 CM26016 BALL BEARING 6204 2RS 2 60 CM24060 CIRCLIP A15 X1,5 2 61 CM20571 CIRCLIP 20 2 62 CM20572 CIRCLIP 47 2 66 CM28548 PIN 5X5X10 2

70 CM20580 SWITCH 230V ...................................................... 1 ......... CX44DUOE ONLY

70 CM20597 SWITCH110 V ...................................................... 1 ......... CX44DUO ONLY

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 21

Page 22

CX44 DUO HAND MIXER — MIXER ASSEMBLY

BODY ASSY.

176

105

175

174

123

121

122

107

126

127

126

129

130

128

126

127

126

129

130

114

125

PAGE 22 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)

103

120

101

Page 23

CX44 DUO HAND MIXER — MIXER ASSEMBLY

BODY ASSY.

NO PART NO PART NAME QTY. REMARKS

71 CM20649 KNOB SWITCH 1 72 CM20650 LEVER 1 73 CM20568 SUPPRESSOR 1

76 CM23557 CORD, ELECTRIC 230 V WITH EU PLUG ........... 1 ........ CX44DUOE ONLY

76 CM27030 CORD, ELECTRIC 230 V WITH CH PLUG ............ 1 ........ CX44DUOE ONLY

76 CM27053 CORD, ELECTRIC 230 V WITH UK PLUG ............ 1 ........ CX44DUOE ONLY

76 CM27035 CORD, ELECTRIC 110 V WITH UK PLUG ............ 1 ........ CX44DUO ONLY

76 CM27054 CORD, ELECTRIC 110 V WITH USA PLUG ......... 1 ........ CX44DUO ONLY

77 CM20564 CABLE 1 79 CM20520 CORD GUARD 1 80 CM20586 WIRE BLUE 1 81 CM20586 WIRE BLUE 1 82 CM20587 WIRE 1 83 CM20587 WIRE 1 85 CM20579 TERMINAL BLOCK 1 86 CM20569 BRUSH HOLDER 1 87 CM20566 BRUSH SET 1 90 CM25062 SCREW 4 X 15 2 91 CM25049 SCREW 4 X 16 18 93 CM20636 SCREW 4X55 4 94 CM25031 SCREW 4X70 2 95 CM20574 SCREW 4X70/30 2 96 CM20575 SCREW M6X20 8 97 CM20577 SCREW 30X12 2 101 CM20578 BALL 5 MM 1 103 CM20507 SPRING FOR GEAR SWITCH 1 105 CM20521 CORD CLAMP 1 107 CM20662 SEALING 1 120 CM20663 SHAFT 1 121 CM28568 CIRCLIP 2 122 CM20664 GEAR 1 123 CM28569 CIRCLIP 8 1

124 CM20665 HEXAFIX® LEFT ................................................... 1 ........ INCLUDES ITEMS W/ #

125 CM20666 HEXAFIX® RIGHT ................................................. 1 ........ INCLUDES ITEMS W/ $

126#$ CM20667 RING HEXAFIX 127#$ CM20668 SPRING FOR HEXAFIX 128#$ CM20669 PIN FOR HEXAFIX 129#$ CM20670 SLEEVE HEXAFIX 130#$ CM20571 CIRCLIP 20 2 174 CM20510 SPRING FOR SWITCH 1 175 CM20607 SPRING FOR KNOB 1 176 DCL1260 DECAL; STOW LOGO 1

4 2 4 2

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 23

Page 24

Effective: February 22, 2006

TERMS AND CONDITIONS OF SALE — PARTS

PAYMENT TERMS

Terms of payment for parts are net 30 days.

FREIGHT POLICY

All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier.

MINIMUM ORDER

The minimum charge for orders from Multiquip is $15.00 net. Customers will be asked for instructions regarding handling of orders not meeting this requirement.

RETURNED GOODS POLICY

Return shipments will be accepted and credit will be allowed, subject to the following provisions:

1. A Returned Material Authorization must be approved by Multiquip prior to shipment.

2. To obtain a Return Mater ial Authorization, a list must be provided to Multiquip Parts Sales that defines item numbers, quantities, and descriptions of the items to be returned.

a. The parts numbers and descriptions

must match the current parts price list.

b. The list must be typed or computer

generated.

c. The list must state the reason(s) for

the return.

d. The list must reference the sales

order(s) or invoice(s) under which the items were originally purchased.

e. The list must include the name and

phone number of the person requesting the RMA.

3. A copy of the Return Material Authorization must accompany the return shipment.

4. Freight is at the sender’s expense. All parts must be returned freight prepaid to Multiquip’s designated receiving point.

5. Parts must be in new and resalable con-

6. The following items are not returnable:

7. The sender will be notified of any material

8. Such material will be held for five working

9. Credit on returned parts will be issued at

10. In cases where an item is accepted, for

11. Credit issued will be applied to future

PRICING AND REBATES

Prices are subject to change without prior notice. Price changes are effective on a specific date and all orders received on or after that date will be billed at the revised price. Rebates for price declines and added charges for price increases will not be made for stock on hand at the time of any price change.

Multiquip reserves the right to quote and sell dition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked.

a. Obsolete parts. (If an item is in the

price book and shows as being replaced by another item, it is obsolete.)

b. Any parts with a limited shelf life

(such as gaskets, seals, “O” rings, and other rubber parts) that were purchased more than six months prior to the return date.

c. Any line item with an extended dealer

net price of less than $5.00. d. Special order items.

e. Electrical components.

f. Paint, chemicals, and lubricants.

g. Decals and paper products. h. Items purchased in kits.

received that is not acceptable.

days from notification, pending instructions. If a reply is not received within five days, the material will be returned to the sender at his expense.

dealer net price at time of the original purchase, less a 15% restocking charge.

which the original purchase document can not be determined, the price will be based on the list price that was effective twelve months prior to the RMA date.

purchases only.

direct to Government agencies, and to Original Equipment Manufacturer accounts who use our products as integral parts of their own products.

SPECIAL EXPEDITING SERVICE

A $35.00 surcharge will be added to the invoice for special handling including bus shipments, insured parcel post or in cases where Multiquip must personally deliver the parts to the carrier.

LIMITATIONS OF SELLER’S LIABILITY

Multiquip shall not be liable hereunder for damages in excess of the purchase price of the item with respect to which damages are claimed, and in no event shall Multiquip be liable for loss of profit or good will or for any other special, consequential or incidental damages.

LIMITATION OF WARRANTIES

No warranties, express or implied, are made in connection with the sale of parts or trade accessories nor as to any engine not manufactured by Multiquip. Such warranties made in connection with the sale of new, complete units are made exclusively by a statement of warranty packaged with such units, and Multiquip neither assumes nor authorizes any person to assume for it any other obligation or liability whatever in connection with the sale of its products. Apart from such written statement of warranty, there are no warranties, express, implied or statutory, which extend beyond the description of the products on the face hereof.

PAGE 24 — CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07)

Page 25

NOTE PAGE

CX22/CX44 DUO HAND MIXERS — OPERATION AND PARTS MANUAL — REV. #1 (06/15/07) — PAGE 25

Page 26

OPERATION AND PARTS MANUAL

HERE'S HOW TO GET HELP

PLEASE HAVE THE MODEL AND SERIAL

NUMBER

ON-HAND

WHEN CALLING

PARTS DEPARTMENT

800-427-1244 FAX: 800-672-7877 310-537-3700 FAX: 310-637-3284

SERVICE DEPARTMENT

800-478-1244 FAX: 310-537-4259 310-537-3700

TECHNICAL ASSISTANCE

800-478-1244 FAX: 310-631-5032

WARRANTY DEPARTMENT

800-421-1244, EXT. 279 FAX: 310-537-1173 310-537-3700, EXT. 279

SALES DEPARTMENT

310-661-4242 FAX: 310-604-9237 877-289-7869 (877-BUY-STOW)

STOW CONSTRUCTION EQUIPMENT

A DIVISION OF MULTIQUIP INC.

POST OFFICE BOX 6254

CARSON, CA 90749 310-537-3700 • 888-252-STOW [888-252-7869] FAX: 310-537-1986 • FAX: 800-556-1986 E-MAIL: STOW@multiquip.com • WWW: stowmfg.com

PARTS DEPARTMENT:

800-427-1244 FAX: 800-672-7877

SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:

800-478-1244 FAX: 310-631-5032